If something goes wrong, return an error code, instead of
assuming that everything went fine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Be sure that I2C reads won't use stack by passing
a pointer to the state buffer, that we know it was
allocated via kmalloc, instead of relying on the buffer
allocated by an I2C client.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
dib0700_ctrl_rd() takes a RX and a TX pointer. Be sure that
both will point to a memory allocated via kmalloc().
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of sending USB commands for every stats call, collect
them once, when status is updated. As the frontend kthread
will call it on every few seconds, the stats will still be
collected.
Besides reducing the amount of USB/I2C transfers, this also
warrants that all stats will be collected at the same time,
and makes easier to convert it to DVBv5 stats in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's no sense on decoding and generating a RC key code if
there was an error on the URB control message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Reviewed-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into patchwork
Linux 4.8
* tag 'v4.8': (1761 commits)
Linux 4.8
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
MAINTAINERS: Switch to kernel.org email address for Javi Merino
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
x86/init: Fix cr4_init_shadow() on CR4-less machines
MIPS: Fix detection of unsupported highmem with cache aliases
MIPS: Malta: Fix IOCU disable switch read for MIPS64
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
...
Fixes this smatch warning:
drivers/media/usb/ttusb-dec/ttusb_dec.c:243 ttusb_dec_handle_irq() error: buffer overflow 'rc_keys' 26 <= 126
As the RC keys should be enabled previously, via:
set_bit(rc_keys[i], input_dev->keybit);
It wouldn't go past the buffer in practice. Yet, as bad
things may happen when going past buffer, it doesn't hurt adding
a check here.
While here, fix CodingStyle issues on the routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This avoids some low-level operations.
It has the benefit that now register values van be read from /sys/kernel/debug/regmap
The maximum register value is just a guess - all higher addresses read as zero.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that there is a i2c_client, use the more specific dev for logging.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that all users of legacy attach are converted it can be removed.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cx231xx does not yet support attaching new-style i2c_client DVB demod
drivers. Add necessary code base on tuner support for i2c_client.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Afterwards it is possible to convert attaching in card drivers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When si2165_init fails, the clk values in state are still at zero.
But the dvb-core ignores the return value of init will call tune
afterwards.
This will trigger a division by zero when tuning.
At least check for the variables to be non-zero before dividing.
This happened for a system with WinTV HVR-4400 PCIe-card after suspend-to-disk.
Do suspend-to-disk without accessing the DVB device before.
After wakeup try to tune.
si2165_init fails at checking the chip_mode and aborts.
Then si2165_set_if_freq_shift will fail with div-by-zero.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Such fallback string is present in the 'soc_camera' version of the R-Car VIN
driver, so need to add it here as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
inside lgdt3306a_search we reading demod status 20 times with 50 msec sleep after each read.
This gives us more than 1 sec of delay. Removing this delay should not affect demod functionality.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Acked-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "_irq_audio_queues" runs the audio upstream handler.
It has a single work item(&dev->_audio_work_entry) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work item has been flushed in cx25821_stop_upstream_audio() to ensure
that nothing is pending when the driver is disconnected.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Workqueues shouldn't be freed. destroy_workqueue should be used instead.
destroy_workqueue safely destroys a workqueue and ensures that all pending
work items are done before destroying the workqueue.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
if specified DVB-C bandwidth not supported then force 8MHz.
Should work for most cases.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add these options as module parameters for now; should other drivers
need similar options we could add it to the LIRC api.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a duplicate of the timeout in rc_dev.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Added function to read BER for ISDB-T
Also SNR values fixed for ISDB-T
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tha ARM randconfig builds came up with another rare build failure
for the dib3000mc driver, when dvb-usb-dibusb-mb is built-in and
dib3000mc is a loadable module:
ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
Apparently this used to be a valid configuration (build-time, not
run-time), but broke as part of a cleanup.
I tried reverting the cleanup, but saw that the code was still wrong
then. This version adds a dependency for dib3000mb, to ensure that
dib3000mb does not force the dibusb_dib3000mc_frontend_attach function
to be built-in when dib3000mc is a loadable module.
I have also checked the two other files that were changed in the original
cleanup, and found them to be correct in either version, so I do not
touch that part.
As this is a rather obscure bug, there is no need for backports.
Fixes: 028c70ff42 ("[media] dvb-usb/dvb-usb-v2: use IS_ENABLED")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Tha ARM randconfig builds came up with another rare build failure
for the dib3000mc driver, when dvb-usb-dibusb-mb is built-in and
dib3000mc is a loadable module:
ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/usb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
Apparently this used to be a valid configuration (build-time, not
run-time), but broke as part of a cleanup.
I tried reverting the cleanup, but saw that the code was still wrong
then. This tries to fix the code properly, by moving the problematic
functions into a new file that now is built as a loadable module or
built-in, whichever is correct for a particular configuration. It fixes
the regression as well as the runtime problem that already existed.
The new module dependency chain is now:
dvb-usb-{dibusb_mc,a800,dib0700,umt-010,gp8psk} dvb-usb-dibusb-mb
| | | |
dvb-usb-dibusb-mc-common | ___________| |
| | | | |
dib3000mc (frontend) | | | dib3000mb (frontend)
| | |
| | |
dvb-usb-dibusb-common
I have also checked the two other files that were changed in the original
cleanup, and found them to be correct in either version, so I do not
touch that part.
As this is a rather obscure bug, there is no need for backports.
Fixes: 028c70ff42 ("[media] dvb-usb/dvb-usb-v2: use IS_ENABLED")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ensure multiple separate register reads are from the same snapshot
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently we do not know what variant (bit length) of the nec protocol
is used, other than from guessing from the length of the scancode. Now
nec will be handled the same way as the sony protocol or the rc6 protocol;
one variant per bit length.
In the future we might want to expose the rc protocol type to userspace
and we don't want to be introducing this world of pain into userspace
too.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The hardware does not decode the 16, 20 or 24 bit variety.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When reporting decoded protocol use the enum rather than the bitmap.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ir_raw_event_handle is called anyway after the hw fifo content stored
in nvt->buf[] has been written to the kfifo. There is not really a
benefit in the potential additional call to ir_raw_event_handle
whilst nvt->buf[] is being processed.
Getting rid of this additional call allows to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The call to nvt_get_rx_ir_data and nvt_process_rx_ir_data from
the ISR is protected with spinlock nvt->lock. Therefore it's
guaranteed that nvt->pkts is 0 when entering nvt_get_rx_ir_data
(as nvt->pkts is set to 0 at the end of nvt_process_rx_ir_data).
Having said that we can remove b_idx.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When removing module nuvoton-cir I get a fifo overrun warning.
It turned out to be caused by a spurious interrupt when the logical CIR
device is being disabled (although no interrupt source bit being set).
Reading the interrupt status register returns 0xff, therefore the fifo
overrun bit is mistakenly interpreted as being set.
Fix this by ignoring interrupts when interrupt source and status register
reads return 0xff.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This partly reverts commit 078600f514.
Due to the relocation of input_register_device() call, holding down a
button on an IR remote no longer resulted in repeated key down events.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check demod and ts locks and report lock status according to those.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use correct device for logging functions as we now have it due to
proper I2C client bindings.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add I2C driver bindings in order to support proper I2C driver
registration with driver core.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
