Also added check for an error condition in bcm2835_dma_create_cb_chain
that showed up during development of this patch.
Tested using dmatest for all enabled channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add slave_sg support to bcm2835-dma using shared allocation
code for bcm2835_desc and DMA-control blocks already used by
dma_cyclic.
Note that bcm2835_dma_callback had to get modified to support
both modes of operation (cyclic and non-cyclic).
Tested using:
* Hifiberry I2S card (using cyclic DMA)
* fb_st7735r SPI-framebuffer (using slave_sg DMA via spi-bcm2835)
playing BigBuckBunny for audio and video.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bcm2835 dma system has 2 basic types of dma-channels:
* "normal" channels
* "light" channels
Lite channels are limited in several aspects:
* internal data-structure is 128 bit (not 256)
* does not support BCM2835_DMA_TDMODE (2D)
* DMA length register is limited to 16 bit.
so 0-65535 (not 0-65536 as mentioned in the official datasheet)
* BCM2835_DMA_S/D_IGNORE are not supported
The detection of the type of mode is implemented by looking at
the LITE bit in the DEBUG register for each channel.
This allows automatic detection.
Based on this the maximum block size is set to (64K - 4) or to 1G
and this limit is honored during generation of control block
chains. The effect is that when a LITE channel is used more
control blocks are used to do the same transfer (compared
to a normal channel).
As there are several sources/target DREQS that are 32 bit wide
we need to have the transfer to be a multiple of 4 as this would
break the transfer otherwise.
This is why the limit of (64K - 4) was chosen over the
alternative of (64K - 4K).
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In preparation of adding slave_sg functionality this patch moves the
generation/allocation of bcm2835_desc and the building of
the corresponding DMA-control-block chain from bcm2835_dma_prep_dma_cyclic
into the newly created method bcm2835_dma_create_cb_chain.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In preparation to consolidating code we move the cyclic member
into the bcm_2835_desc structure.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add additional defines describing the DMA registers
as well as adding some more documentation to those registers.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The original patch contained 3 dma channels that were masked out.
These - as far as research and discussions show - are a
artefacts remaining from the downstream legacy dma-api.
Right now down-stream still includes a legacy api used only
in a single (downstream only) driver (bcm2708_fb) that requires
2D DMA for speedup (DMA-channel 0).
Formerly the sd-card support driver also was using this legacy
api (DMA-channel 2), but since has been moved over to use
dmaengine directly.
The DMA-channel 3 is already masked out in the devicetree in
the default property "brcm,dma-channel-mask = <0x7f35>;"
So we can remove the whole masking of DMA channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
bcm2835-dma supports residue reporting at burst level but didn't report
this via the residue_granularity field.
See also:
b015555327
for the downstream patch.
Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
To be sure we have the cyclic transfers already gone we set cdesc to NULL. It
will prevent the double free.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Residue is a property of any active descriptor. So, any descriptor may be in
different state but residue is a feature of active descriptor. Check if the
asked descriptor is active and return proper residue value for it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Covert dwc->initialized to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have already dedicated variable for flags, therefore no need to create an
additional storage for that. Convert dwc->paused to use dwc->flags.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The code is fixed to satisfy a compiler otherwise we have
drivers/dma/dw/core.c: In function ‘dwc_handle_cyclic’:
drivers/dma/dw/core.c:568: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_tasklet’:
drivers/dma/dw/core.c:590: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_off’:
drivers/dma/dw/core.c:1103: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_cyclic_free’:
drivers/dma/dw/core.c:1469: warning: comparison between signed and unsigned
drivers/dma/dw/core.c: In function ‘dw_dma_probe’:
drivers/dma/dw/core.c:1574: warning: comparison between signed and unsigned
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since struct dw_dma is allocated and regs member is assigned properly we can
use standard IO accessors to the DMA registers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet requires that the LLP_[SD]_EN bits be cleared whenever
LLP.LOC is zero, i.e. in the last descriptor of a multi-block chain.
Make the driver do this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The LMS field indicates from which master the descriptor is to be
read. This patch assumes this is always the same as the memory
side in a peripheral transfer which is true for all known systems.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the DMA controller uses a different byte order than the host CPU,
the hardware linked list descriptor fields need to be byte-swapped.
This patch makes the driver write these fields using the same byte
order it uses for mmio accesses to the DMA engine. I do not know
if this is guaranteed to always be correct.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On some architectures the DMA controller can have two masters connected to
different buses and thus access to memory is possible only through one and
to peripheral through the other.
This patch changes the src and dst master setting to match the direction
of the transfer.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The source and destination masters are reflecting buses or their layers to
where the different devices can be connected. The patch changes the master
names to reflect which one is related to which independently on the transfer
direction.
The outcome of the change is that the memory data width is now always limited
by a data width of the master which is dedicated to communicate to memory.
The patch will not break anything since all current users have the same data
width for all masters. Though it would be nice to revisit avr32 platforms to
check what is the actual hardware topology in use there. It seems that it has
one bus and two masters on it as stated by Table 8-2, that's why everything
works independently on the master in use. The purpose of the sequential patch
is to fix the driver for configuration of more than one bus.
The change is done in the assumption that src_master and dst_master are
reflecting a connection to the memory and peripheral correspondently on avr32
and otherwise on the rest.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 8950052029 ("dmaengine: dw: apply both HS interfaces and remove
slave_id usage") cleaned up the code to avoid usage of depricated slave_id
member of generic slave configuration.
Meanwhile it broke the master selection by removing important call to
dwc_set_masters() in ->device_alloc_chan_resources() which copied masters from
custom slave configuration to the internal channel structure.
Everything works until now since there is no customized connection of
DesignWare DMA IP to the bus, i.e. one bus and one or more masters are in use.
The configurations where 2 masters are connected to the different masters are
not working anymore. We are expecting one user of such configuration and need
to select masters properly. Besides that it is obviously a performance
regression since only one master is in use in multi-master configuration.
Select masters in accordance with what user asked for. Keep this patch in a form
more suitable for back porting.
We are safe to take necessary data in ->device_alloc_chan_resources() because
we don't support generic slave configuration embedded into custom one, and thus
the only way to provide such is to use the parameter to a filter function which
is called exactly before channel resource allocation.
While here, replase BUG_ON to less noisy dev_warn() and prevent channel
allocation in case of error.
Fixes: 8950052029 ("dmaengine: dw: apply both HS interfaces and remove slave_id usage")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit ef859312c3 ("dmaengine: core: Use dev_ functions for debug and
error prints") wasn't quite right in __dma_request_channel() by claiming
that all pr_ prints have valid DMA channel pointer. Obviously it is not
true as __dma_request_channel() is looking for a channel and returns NULL
if it does not find it.
Prevent this potential NULL pointer dereference by reverting back to
pr_debug().
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the below checkpatch.pl warnings.
WARNING: void function return statements are not generally useful
+ return;
+}
WARNING: void function return statements are not generally useful
+ return;
+}
WARNING: Missing a blank line after declarations
+ u32 errors = status & XILINX_VDMA_DMASR_ALL_ERR_MASK;
+ vdma_ctrl_write(chan, XILINX_VDMA_REG_DMASR,
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When VDMA is configured in Non-sg mode
Users can queue descriptors greater than h/w configured frames.
Current driver allows the user to queue descriptors upto h/w configured.
Which is wrong for non-sg mode configuration.
This patch fixes this issue.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This VDMA is a soft ip, which can be programmed to support
32 bit addressing or greater than 32 bit addressing.
When the VDMA ip is configured for 32 bit address space
the buffer address is specified by a single register
(0x5C for MM2S and 0xAC for S2MM channel).
When the VDMA core is configured for an address space greater
than 32 then each buffer address is specified by a combination of
two registers.
The first register specifies the LSB 32 bits of address,
while the next register specifies the MSB 32 bits of address.
For example, 5Ch will specify the LSB 32 bits while 60h will
specify the MSB 32 bits of the first start address.
So we need to program two registers at a time.
This patch adds the 64 bit addressing support to the vdma driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently drivers are limited to 19 slots for cyclic transfers.
However, if the DMA burst size is the same as the period size,
the period size can be changed to the full buffer size and
intermediate interrupts activated. Since intermediate interrupts
will trigger for each burst and the burst size is the same as
the period size, the driver will get interrupts each period as
expected. This has the benefit of allowing the functionality of
many more slots, but only uses 2 slots.
This workaround is only active if more than 19 slots are needed
and the burst size matches the period size.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The dynamic or on demand pm_runtime does not work correctly on am335x and
am437x due to interference with hwmod.
Fall back using the pm_runtime usage as it was in the old driver stack,
meaning that at probe time call pm_runtime_enable() and
pm_runtime_get_sync() for the TPTCs as well.
Fixes: 1be5336bc7 ("dmaengine: edma: New device tree binding")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current OF translation of channels can never work with
any DMA client using the DMA channels directly: the only way
to get the channels initialized properly is in the
dma_async_device_register() call, where chan->dev etc is
allocated and initialized.
Allocate and initialize all possible DMA channels and
only augment a target channel with the periph_buses at
of_xlate(). Remove some const settings to make things work.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_get_slave_caps() API only checked for slave capability where
we use slave capabilities for cyclic dma operations as well, so we
should add the cyclic case here too.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When client request a non existing channel from of_dma_xilinx_xlate
we get a NULL pointer dereferencing. This patch fix this problem.
Signed-off-by: Franck Jullien <franck.jullien@odyssee-systemes.fr>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the client queues up more transfers the driver will not able to move to
the next transfer without knowing that the previous descriptor is
completed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When based on the CCR_ENABLE bit the channel is stopped we should not call
omap_dma_callback(), only change the return value to DMA_COMPLETE. Client
drivers will do the right thing to clean up the channel after the transfer
has been completed.
Check the CCR_ENABLE only if the channel is running and not paused since
pause in sDMA means that the channel is stopped.
This will fix one hard to reproduce race condition when the channel is
terminated during transfer (affecting cyclic operation).
Fixes: 1a7cf7b26f ("dmaengine: omap-dma: Handle cases when the channel is polled for completion")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch extends the capabilities of the driver to handle DMA
transfers to and from devices of 1, 2, 4, 16 (for MPC512x), and 32 byte
widths.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since the MPC8308 has no external request lines to initiate DMA transfers,
all transfers must be triggered by software.
Because of this, the current implementation of DMA transfers from and to
devices on MPC8308 SoCs using major and minor loops is faulty: After the
completion of the first major loop, the DMA engine resets the start flag in
the channel's TCD, thus halting the transfer. The driver would have to set
the start bit again to trigger the next iteration of the major loop; on
MPC512x SoCs, this is done via the external request lines, so in this case,
the driver doesn't have to interfer in any way.
This has the effect that on MPC8308s, every DMA transfer to or from a
device hangs after executing the first major loop.
The patch fixes this behavior by using just one major loop for the whole
DMA transfer on MPC8308s.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This tells, for example, IOMMU what the maximum size of a segment
the DMA controller can send.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The timeout capability is only available on the so called DMA write channels,
i.e. associated with UART Rx FIFO. It means we don't need to check the
direction of the channel to handle timeouts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current code allows only up to 3 descriptors to be programmed to the hardware
since it is used wrong calculations. Change % to min_t() to allow as many
descriptors as user supplied. At once it could be programmed up to 4
descriptors due to hardware limitations.
The issue was found under stress test, so it might not bother ordinary users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a typo in documentation regarding to descriptor empty bit (DESCE)
which is set to 1 when descriptor is empty. Thus, status register at the end of
a transfer usually returns all DESCE bits set and thus it will never be zero.
Moreover, there are 2 bits (CDESC) that encode current descriptor, on which
interrupt has been asserted. In case when we have few descriptors programmed we
might have non-zero value.
Remove DESCE and CDESC bits from DMA channel status register (HSU_CH_SR) when
reading it.
Fixes: 2b49e0c567 ("dmaengine: append hsu DMA driver")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit f0579c8cea ("dmaengine: hsu: speed up residue calculation")
speeded up calculation of the queued descriptor but broke the initial residue
value for active descriptor.
In accordance with documentation the hardware descriptor is updated each time
DMA transfered some bytes. It means we have to calculate a sum of lengths of
non-submitted hardware descriptors and whatever current values in the hardware.
Do this straightforward.
Fixes: f0579c8cea ("dmaengine: hsu: speed up residue calculation")
Cc: stable@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
HSU_CH_MTSR register should be programmed to a minimum size to transfer. This
size on a memory side of the transfer. Program it accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
According to dmaengine kerneldoc the struct dma_chan has always a non-NULL
pointer to DMA device and a test in dma_async_device_register()
validates that DMA device must also point to struct device.
All pr_ prints except one in dma_channel_table_init() have valid DMA
channel or DMA device pointer available which allow convert them to use
dev_ functions and thus able to show the associated DMA device.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There are only three patches this time, most other changes to
files in include/asm-generic tend to go through the tree of whoever
depends on the change.
Two patches are cleanups for stuff that is no longer needed,
the main change is to adapt the generic version of BUG_ON()
for CONFIG_BUG=n to make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings
about that undefined behavior in randconfig builds when
we keep going on after hitting a BUG_ON().
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8tPL
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are only three patches this time, most other changes to files in
include/asm-generic tend to go through the tree of whoever depends on
the change.
Two patches are cleanups for stuff that is no longer needed, the main
change is to adapt the generic version of BUG_ON() for CONFIG_BUG=n to
make it behave consistently with BUG().
This avoids undefined behavior along with a number of warnings about
that undefined behavior in randconfig builds when we keep going on
after hitting a BUG_ON()"
* tag 'asm-generic-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: remove old nonatomic-io wrapper files
asm-generic: default BUG_ON(x) to if(x)BUG()
asm-generic: page.h: Remove useless get_user_page and free_user_page
Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP, uniphier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ynNj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Newly added support for additional SoCs:
- Axis Artpec-6 SoC family
- Allwinner A83T SoC
- Mediatek MT7623
- NXP i.MX6QP SoC
- ST Microelectronics stm32f469 microcontroller
New features:
- SMP support for Mediatek mt2701
- Big-endian support for NXP i.MX
- DaVinci now uses the new DMA engine dma_slave_map
- OMAP now uses the new DMA engine dma_slave_map
- earlyprintk support for palmchip uart on mach-tango
- delay timer support for orion
Other:
- Exynos PMU driver moved out to drivers/soc/
- Various smaller updates for Renesas, Xilinx, PXA, AT91, OMAP,
uniphier"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: uniphier: rework SMP code to support new System Bus binding
ARM: uniphier: add missing of_node_put()
ARM: at91: avoid defining CONFIG_* symbols in source code
ARM: DRA7: hwmod: Add data for eDMA tpcc, tptc0, tptc1
ARM: imx: Make reset_control_ops const
ARM: imx: Do L2 errata only if the L2 cache isn't enabled
ARM: imx: select ARM_CPU_SUSPEND only for imx6
dmaengine: pxa_dma: fix the maximum requestor line
ARM: alpine: select the Alpine MSI controller driver
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: OMAP2+: Add rtc hwmod configuration for ti81xx
ARM: s3c24xx: Avoid warning for inb/outb
ARM: zynq: Move early printk virtual address to vmalloc area
ARM: DRA7: hwmod: Add custom reset handler for PCIeSS
ARM: SAMSUNG: Remove unused register offset definition
ARM: EXYNOS: Cleanup header files inclusion
drivers: soc: samsung: Enable COMPILE_TEST
MAINTAINERS: Add maintainers entry for drivers/soc/samsung
...
This is smallish update with minor changes to core and new driver and usual
updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the mapping.
- We now expose the maxburst for slave dma as new capability so clients can
know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in progress
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wCCJ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This is smallish update with minor changes to core and new driver and
usual updates. Nothing super exciting here..
- We have made slave address as physical to enable driver to do the
mapping.
- We now expose the maxburst for slave dma as new capability so
clients can know this and program accordingly
- addition of device synchronize callbacks on omap and edma.
- pl330 updates to support DMAFLUSHP for Rockchip platforms.
- Updates and improved sg handling in Xilinx VDMA driver.
- New hidma qualcomm dma driver, though some bits are still in
progress"
* tag 'dmaengine-4.6-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (40 commits)
dmaengine: IOATDMA: revise channel reset workaround on CB3.3 platforms
dmaengine: add Qualcomm Technologies HIDMA channel driver
dmaengine: add Qualcomm Technologies HIDMA management driver
dmaengine: hidma: Add Device Tree binding
dmaengine: qcom_bam_dma: move to qcom directory
dmaengine: tegra: Move of_device_id table near to its user
dmaengine: xilinx_vdma: Remove unnecessary variable initializations
dmaengine: sirf: use __maybe_unused to hide pm functions
dmaengine: rcar-dmac: clear pertinence number of channels
dmaengine: sh: shdmac: don't open code of_device_get_match_data()
dmaengine: tegra: don't open code of_device_get_match_data()
dmaengine: qcom_bam_dma: Make driver work for BE
dmaengine: sun4i: support module autoloading
dma/mic_x100_dma: IS_ERR() vs PTR_ERR() typo
dmaengine: xilinx_vdma: Use readl_poll_timeout instead of do while loop's
dmaengine: xilinx_vdma: Simplify spin lock handling
dmaengine: xilinx_vdma: Fix issues with non-parking mode
dmaengine: xilinx_vdma: Improve SG engine handling
dmaengine: pl330: fix to support the burst mode
dmaengine: make slave address physical
...
Pull dma_*_writecombine rename from Ingo Molnar:
"Rename dma_*_writecombine() to dma_*_wc()
This is a tree-wide API rename, to move the dma_*() write-combining
APIs closer in name to their usual API families. (The old API names
are kept as compatibility wrappers to not introduce extra breakage.)
The patch was Coccinelle generated"
* 'mm-pat-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dma, mm/pat: Rename dma_*_writecombine() to dma_*_wc()
Previously we unloaded the interrupts and reloaded in order to work around
a channel reset bug that cleared the MSIX table. This approach just isn't
practical when a reset needs to happen in the error handler that just
happens to be running in interrupt context (bottom half). It looks like we
can work around the hardware issue by just storing a shadow copy of the
MSIX table and restore it after reset.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for hidma engine. The driver consists of two
logical blocks. The DMA engine interface and the low-level interface.
The hardware only supports memcpy/memset and this driver only support
memcpy interface. HW and driver doesn't support slave interface.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The Qualcomm Technologies HIDMA device has been designed to support
virtualization technology. The driver has been divided into two to follow
the hardware design.
1. HIDMA Management driver
2. HIDMA Channel driver
Each HIDMA HW consists of multiple channels. These channels share some set
of common parameters. These parameters are initialized by the management
driver during power up. Same management driver is used for monitoring the
execution of the channels. Management driver can change the performance
behavior dynamically such as bandwidth allocation and prioritization.
The management driver is executed in host context and is the main
management entity for all channels provided by the device.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Creating a QCOM directory for all QCOM DMA source files.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When computing the residue we need two pieces of information: the current
descriptor and the remaining data of the current descriptor. To get
that information, we need to read consecutively two registers but we
can't do it in an atomic way. For that reason, we have to check manually
that current descriptor has not changed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Suggested-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reported-by: David Engraf <david.engraf@sysgo.com>
Tested-by: David Engraf <david.engraf@sysgo.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename dma_*_writecombine() to dma_*_wc(), so that the naming
is coherent across the various write-combining APIs. Keep the
old names for compatibility for a while, these can be removed
at a later time. A guard is left to enable backporting of the
rename, and later remove of the old mapping defines seemlessly.
Build tested successfully with allmodconfig.
The following Coccinelle SmPL patch was used for this simple
transformation:
@ rename_dma_alloc_writecombine @
expression dev, size, dma_addr, gfp;
@@
-dma_alloc_writecombine(dev, size, dma_addr, gfp)
+dma_alloc_wc(dev, size, dma_addr, gfp)
@ rename_dma_free_writecombine @
expression dev, size, cpu_addr, dma_addr;
@@
-dma_free_writecombine(dev, size, cpu_addr, dma_addr)
+dma_free_wc(dev, size, cpu_addr, dma_addr)
@ rename_dma_mmap_writecombine @
expression dev, vma, cpu_addr, dma_addr, size;
@@
-dma_mmap_writecombine(dev, vma, cpu_addr, dma_addr, size)
+dma_mmap_wc(dev, vma, cpu_addr, dma_addr, size)
We also keep the old names as compatibility helpers, and
guard against their definition to make backporting easier.
Generated-by: Coccinelle SmPL
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bhelgaas@google.com
Cc: bp@suse.de
Cc: dan.j.williams@intel.com
Cc: daniel.vetter@ffwll.ch
Cc: dhowells@redhat.com
Cc: julia.lawall@lip6.fr
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: luto@amacapital.net
Cc: mst@redhat.com
Cc: tomi.valkeinen@ti.com
Cc: toshi.kani@hp.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1453516462-4844-1-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
adding unmap of sources and destinations while doing dequeue.
Signed-off-by: Xuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After using the function of_device_get_match_data(), the
of_device_id table for tegra20 dma is not used by probe()
and hence moving it near to place where platform driver is
defined as this table used only on this data structure.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch removes the unnecessary variable initializations
in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The sirf dma driver uses #ifdef to check for CONFIG_PM_SLEEP
for its suspend/resume code but then has no #ifdef for the
respective runtime PM code, so we get a warning if CONFIG_PM
is disabled altogether:
drivers/dma/sirf-dma.c:1000:12: error: 'sirfsoc_dma_runtime_resume' defined but not used [-Werror=unused-function]
This removes the existing #ifdef and instead uses __maybe_unused
annotations for all four functions to let the compiler know it
can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
DMACHCLR clears each channels, but its channel number is based on
its SoC or IP. Current driver is using fixed 0x7fff (= for 15ch),
it is not good match for Gen3 or Gen2 Audio DMAC. This patch fixes it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use of_device_get_match_data() for getting matched data
instead of implementing this locally.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes the Qualcomm BAM dmaenging driver to work with big
endian kernels.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
MODULE_DEVICE_TABLE() is missing, so the module isn't auto-loading on
supported systems. This commit adds the missing line so it loads
automatically when building it as a module and running on a system
with the early sunxi DMA engine.
Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is harmless because the caller only cares about zero vs non-zero
but we should be returning PTR_ERR() here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
While testing audio with pxa2xx-ac97, underrun were happening while the
user application was correctly feeding the music. Debug proved that the
cyclic transfer is not cyclic, ie. the last descriptor did not loop on
the first.
Another issue is that the descriptor length was always set to 8192,
because of an trivial operator issue.
This was tested on a pxa27x platform.
Fixes: a57e16cf03 ("dmaengine: pxa: add pxa dmaengine driver")
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It is sometimes necessary to poll a memory-mapped register until its
value satisfies some condition use convenience macros
that do this instead of do while loop's.
This patch updates the same in the driver.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch simplifies the spin lock handling in the driver
by moving locking out of xilinx_dma_start_transfer() API
and xilinx_dma_update_completed_cookie() API.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes issues with the Non-parking mode(Cirular mode).
With the existing driver in cirular mode if we submit frames less than h/w
configured we simply end-up having misconfigured vdma h/w.
This patch fixes this issue by configuring the frame count register.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current driver allows user to queue up multiple segments
on to a single transaction descriptor. User will submit this single desc
and in the issue_pending() we decode multiple segments and submit to SG HW engine.
We free up the allocated_desc when it is submitted to the HW.
Existing code prevents the user to prepare multiple trasactions at same time as
we are overwrite with the allocated_desc.
The best utilization of HW SG engine would happen if we collate the pending
list when we start dma this patch updates the same.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The two header files got moved to include/linux, and most
users were already converted, this changes the remaining drivers
and removes the files.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
This patch fixes the burst mode that will break DMA uart on SoCFPGA.
In some cases, some SoCS didn't support the multi-burst
even if the devices who use the pl330 claim support the maxburst.
Fixes: commit 848e977
"dmaengine: pl330: support burst mode for dev-to-mem and mem-to-dev transmit"
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Tested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The current number of requestor lines is limited to 31. This was an
error of a previous commit, as this number is platform dependent, and is
actually :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
The previous testing did not reveal the faulty constant as on pxa[23]xx
platforms, only camera, MSL and USB are above requestor 32, and in these
only the camera has a driver using dma.
Fixes: e87ffbdf06 ("dmaengine: pxa_dma: fix the no-requestor case")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vinod Koul <vinod.koul@intel.com>
In acpi_dma_request_slave_chan_by_name() the debug message is printed before
the actual matching happens. Correct the message itself to be in align with the
flow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is a typo in the definition of IDMA64C_CFGH_WR_ISSUE_THD(x). Fix it by
swapping characters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The mxs-dma unit is also available on i.MX6UL. Make it possible to
select it in Kconfig.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to avoid possible race condition when client drivers are using
dmaengine_terminate_sync() call to disable the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need the callback to support the dmaengine_terminate_sync().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We need the callback to support the dmaengine_terminate_sync().
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Future IOATDMA hardware will take advantage of descriptors residing in
contiguous memory. Setting the descriptor ring in max config DMA memory
of 2MB. Each channel will need 2 of these chunks. This should provide 64k
of 64B descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Moving to contingous memory backed descriptor rings. This makes is really
difficult and complex to do reshape. Going to remove this as I don't think
we need to do it anymore.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Converting old pci_pool_* calls to "new" dma_pool_* to make everything
uniform.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The commit 2895b2cad6 ("dmaengine: dw: fix cyclic transfer callbacks")
re-enabled BLOCK interrupts with regard to make cyclic transfers work. However,
this change becomes a regression for non-cyclic transfers as interrupt counters
under stress test had been grown enormously (approximately per 4-5 bytes in the
UART loop back test).
Taking into consideration above enable BLOCK interrupts if and only if channel
is programmed to perform cyclic transfer.
Fixes: 2895b2cad6 ("dmaengine: dw: fix cyclic transfer callbacks")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mans Rullgard <mans@mansr.com>
Tested-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The datasheet requires that the user must clear LLP_[SD]_EN bits whenever
LLP.LOC is zero, i.e. in the last descriptor of a multi-block chain.
Make the driver do this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max burst capability for dmaengine and
limit burst capability to one for PL330_QUIRK_BROKEN_NO_FLUSHP
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add max_burst to dma_get_slave_caps for clients
to get the burst capability of slave dma controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch add "arm,pl330-broken-no-flushp" quirk to avoid execute
DMAFLUSHP if Soc doesn't support it.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Doug Anderson <dianders@chromium.org>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds to support burst mode for dev-to-mem and
mem-to-dev transmit.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
cc: Heiko Stuebner <heiko@sntech.de>
cc: Doug Anderson <dianders@chromium.org>
cc: Olof Johansson <olof@lixom.net>
Reviewed-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When retrieving the residue value, the SRC/DST fields of the
active PaRAM are read to determine the current position of
the DMA engine. However, the AM335x Technical Reference Manual
states:
11.3.3.6 Parameter Set Updates
After the TR is read from the PaRAM (and is in the process
of being submitted to the EDMA3TC), the following fields are
updated as needed: ... SRC DST
This means SRC/DST is incremented even though the DMA transfer
may not have started yet or is in progress. Thus if the reader
of the residue accesses the DMA buffer too quickly, the CPU is
misinformed about the data that has been successfully processed.
The CCSTAT.ACTV register is a boolean that is set if any TR is
being processed by either the EMDA3CC or EDMA3TC. By polling
this register it is possible to ensure that the residue value
returned is valid for immediate processing. However, since the
DMA engine may be active, polling may never hit a moment where
no TR is being processed. To handle this, the SRC/DST is also
polled to see if it changes. And as a last resort, a max loop
count for the busy waiting exists to avoid an infinite loop.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
WildcatPoint PCH as seen on MacBook 12-inch (Early 2015) has PCI enabled
DesignWare DMA controller. Enable it by adding its ID to the corresponding
driver.
Reported-by: Leif Liddy <leif.liddy@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=110901
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The timer_event() function seems to have a bug where it ends up marking the
last entry as non-responding and eventually attempts to restart the
channel. This also continuously happen when idle. What needs to happen is
for us to make sure there are no descriptors active and then handle that
case properly. We should only hit the "cleanup" stage if there are still
active descriptors.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
CC [M] drivers/dma/ioat/prep.o
drivers/dma/ioat/prep.c: In function 'ioat_prep_pqxor':
drivers/dma/ioat/prep.c:682:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
drivers/dma/ioat/prep.c: In function 'ioat_prep_pqxor_val':
drivers/dma/ioat/prep.c:714:1: warning: the frame size of 1048 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
gcc version 5.3.1 20151219 (Ubuntu 5.3.1-4ubuntu1)
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Debugging ALSA hangups it was found that EP9302 (latest E2 rev.) DMA controller
sometimes asserts STALL interrupt instead of NFB interrupt. Simply ignoring the
difference and simply acting upon the amount of data we still have to transfer
seems to work fine. This somehow sounds similar to M2M issue which is already
dealt with in the driver, when the controller asserts DONE interrupt too early.
The issue is not documented in Cirrus Logic erratas for EP93XX, but original
Cirrus DMA driver from 2003 (not based on DMA API) did the similar handling
of STALL interrupt. In-tree driver (6d831c65) did it also, before conversion to
DMA engine API.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The offset of SINC should be 9, not 7, here fix this
typo.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Few fixes on drivers have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one
Fixes are on dw, at_hdmac, edma
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=16UM
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Here is my second pull request for this window:
A few driver fixes have piled up and one missed rcar bindings patch
which got somehow lost in for-linus branch so cherry-picked that one.
Fixes are for dw, at_hdmac, edma"
* tag 'dmaengine-fix-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Document SoC specific bindings
dmaengine: at_xdmac: fix resume for cyclic transfers
dmaengine: dw: fix cyclic transfer callbacks
dmaengine: dw: fix cyclic transfer setup
dmaengine: edma: Fix paRAM slot allocation for entry channel 0
When having cyclic transfers, the channel was paused when performing
suspend but was not correctly resumed.
Signed-off-by: Songjun Wu <songjun.wu@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel
eXtended DMA Controller driver")
Cc: <stable@vger.kernel.org> # 4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree in
anyway sooner or later.]
Core
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc
- A few code cleanups of fm801 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Gvgb
-----END PGP SIGNATURE-----
Merge tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"We've had quite busy weeks in this cycle. Looking at ALSA core, the
significant changes are a few fixes wrt timer and sequencer ioctls
that have been revealed by fuzzer recently. Other than that, ASoC
core got a few updates about DAI link handling, but these are rather
straightforward refactoring.
In drivers scene, ASoC received quite lots of new drivers in addition
to bunch of updates for still ongoing Intel Skylake support and
topology API. HD-audio gained a new HDMI/DP hotplug notification via
component. FireWire got a pile of code refactoring/updates with
SCS.1x driver integration.
More highlights are shown below.
[ NOTE: this contains also many commits for DRM. This is due to the
pull of drm stable branch into sound tree, as the base of i915 audio
component work for HD-audio. The highlights below don't contain
these DRM changes, as these are supposed to be pulled via drm tree
in anyway sooner or later. ]
Core:
- Handful fixes to harden ALSA timer and sequencer ioctls against
races reported by syzkaller fuzzer
- Irq description string can be unique to each card; only for
HD-audio for now
ASoC:
- Conversion of the array of DAI links to a list for supporting
dynamically adding and removing DAI links
- Topology API enhancements to make everything more component based
and being able to specify PCM links via topology
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production; we really need to get to the
point where that can be done
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come
- Lots of new features and cleanups for the Renesas drivers
- ANC support for WM5110
- New drivers: Imagination Technologies IPs, Atmel class D speaker,
Cirrus CS47L24 and WM1831, Dialog DA7128, Realtek RT5659 and
RT56156, Rockchip RK3036, TI PC3168A, and AMD ACP
- Rename PCM1792a driver to be generic pcm179x
HD-Audio:
- Use audio component for i915 HDMI/DP hotplug handling
- On-demand binding with i915 driver
- bdl_pos_adj parameter adjustment for Baytrail controllers
- Enable power_save_node for CX20722; this shouldn't lead to
regression, hopefully
- Kabylake HDMI/DP codec support
- Quirks for Lenovo E50-80, Dell Latitude E-series, and other Dell
machines
- A few code refactoring
FireWire:
- Lots of code cleanup and refactoring
- Integrate the support of SCS.1x devices into snd-oxfw driver;
snd-scs1x driver is obsoleted
USB-audio:
- Fix possible NULL dereference at disconnection
- A regression fix for Native Instruments devices
Misc:
- A few code cleanups of fm801 driver"
* tag 'sound-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (722 commits)
ALSA: timer: Code cleanup
ALSA: timer: Harden slave timer list handling
ALSA: hda - Add fixup for Dell Latitidue E6540
ALSA: timer: Fix race among timer ioctls
ALSA: hda - add codec support for Kabylake display audio codec
ALSA: timer: Fix double unlink of active_list
ALSA: usb-audio: Fix mixer ctl regression of Native Instrument devices
ALSA: hda - fix the headset mic detection problem for a Dell laptop
ALSA: hda - Fix white noise on Dell Latitude E5550
ALSA: hda_intel: add card number to irq description
ALSA: seq: Fix race at timer setup and close
ALSA: seq: Fix missing NULL check at remove_events ioctl
ALSA: usb-audio: Avoid calling usb_autopm_put_interface() at disconnect
ASoC: hdac_hdmi: remove unused hdac_hdmi_query_pin_connlist
ASoC: AMD: Add missing include file
ALSA: hda - Fixup inverted internal mic for Lenovo E50-80
ALSA: usb: Add native DSD support for Oppo HA-1
ASoC: Make aux_dev more like a generic component
ASoC: bcm2835: cleanup includes by ordering them alphabetically
ASoC: AMD: Manage ACP 2.x SRAM banks power
...
Cyclic transfer callbacks rely on block completion interrupts which were
disabled in commit ff7b05f29f ("dmaengine/dw_dmac: Don't handle block
interrupts"). This re-enables block interrupts so the cyclic callbacks
can work. Other transfer types are not affected as they set the INT_EN
bit only on the last block.
Fixes: ff7b05f29f ("dmaengine/dw_dmac: Don't handle block interrupts")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
Commit 61e183f830 ("dmaengine/dw_dmac: Reconfigure interrupt and
chan_cfg register on resume") moved some channel initialisation to
a new function which must be called before starting a transfer.
This updates dw_dma_cyclic_start() to use dwc_dostart() like the other
modes, thus ensuring dwc_initialize() gets called and removing some code
duplication.
Fixes: 61e183f830 ("dmaengine/dw_dmac: Reconfigure interrupt and chan_cfg register on resume")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cc: <stable@vger.kernel.org>
This round we have few new features, new driver and updates to few drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of request
flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D5Fb
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This round we have few new features, new driver and updates to few
drivers.
The new features to dmaengine core are:
- Synchronized transfer termination API to terminate the dmaengine
transfers in synchronized and async fashion as required by users.
We have its user now in ALSA dmaengine lib, img, at_xdma, axi_dmac
drivers.
- Universal API for channel request and start consolidation of
request flows. It's user is ompa-dma driver.
- Introduce reuse of descriptors and use in pxa_dma driver
Add/Remove:
- New STM32 DMA driver
- Removal of unused R-Car HPB-DMAC driver
Updates:
- ti-dma-crossbar updates for supporting eDMA
- tegra-apb pm updates
- idma64
- mv_xor updates
- ste_dma updates"
* tag 'dmaengine-4.5-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (54 commits)
dmaengine: mv_xor: add suspend/resume support
dmaengine: mv_xor: de-duplicate mv_chan_set_mode*()
dmaengine: mv_xor: remove mv_xor_chan->current_type field
dmaengine: omap-dma: Add support for DMA filter mapping to slave devices
dmaengine: edma: Add support for DMA filter mapping to slave devices
dmaengine: core: Introduce new, universal API to request a channel
dmaengine: core: Move and merge the code paths using private_candidate
dmaengine: core: Skip mask matching when it is not provided to private_candidate
dmaengine: mdc: Correct terminate_all handling
dmaengine: edma: Add probe callback to edma_tptc_driver
dmaengine: dw: fix potential memory leak in dw_dma_parse_dt()
dmaengine: stm32-dma: Fix unchecked deference of chan->desc
dmaengine: sh: Remove unused R-Car HPB-DMAC driver
dmaengine: usb-dmac: Document SoC specific compatibility strings
ste_dma40: Delete an unnecessary variable initialisation in d40_probe()
ste_dma40: Delete another unnecessary check in d40_probe()
ste_dma40: Delete an unnecessary check before the function call "kmem_cache_destroy"
dmaengine: tegra-apb: Free interrupts before killing tasklets
dmaengine: tegra-apb: Update driver to use GFP_NOWAIT
dmaengine: tegra-apb: Only save channel state for those in use
...
edma_alloc_slot was not checking the channel mapping support existence when
slot 0 has been requested (used as entry slot for channel/event 0).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
Since we have a work around to prevent a system hangup we don't need to provide
a platform data explicitly anymore.
This reverts commit 175267b389.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to bother the hardware when all channels are idle. We have not
to get any interrupts.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have to call dw_dma_disable() to stop any ongoing transfer. On some
platforms we can't do that since DMA device is powered off. Moreover we have no
possibility at that point to check if the platform is affected or not. That's
why we call pm_runtime_get_sync() / pm_runtime_put() unconditionally. On the
other hand we can't use pm_runtime_suspended() because runtime PM framework is
not fully used by the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For interrupt controller that doesn't support irq_disable and hardware
with level interrupt, an extra interrupt can be pending. This patch fixes
the issue by setting IRQ_DISABLE_UNLAZY flag for the interrupt line.
Reference: http://git.kernel.org/tip/e9849777d0e27cdd2902805be51da73e7c79578c
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This commit adds suspend/resume support to the mv_xor driver. The
config and interrupt mask registers must be saved and restored, and
upon resume, the MBus windows configuration must also be done again.
Tested on Armada 388 GP, with a RAID 5 array, accessed before and
after a suspend to RAM cycle.
Based on work from Ofer Heifetz and Lior Amsalem.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When commit 6f166312c6 ("dmaengine: mv_xor: add support for a38x
command in descriptor mode") added support for the descriptor mode
available in Marvell Armada 38x and later SoCs, it added a new
function mv_chan_set_mode_to_desc() which allows to configure a XOR
channel to get the specific operation to be done from each individual
DMA descriptor.
However, this function was mainly a duplicate of the existing
mv_chan_set_mode(), with just the operation being different.
This commit re-organizes the code into a single mv_chan_set_mode()
function, which takes the operation mode as argument, and the
mv_xor_channel_add() function decides whether to use
XOR_OPERATION_MODE_IN_DESC or XOR_OPERATION_MODE_XOR.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Since commit 3e4f52e2da ("dma: mv_xor: Simplify the DMA_MEMCPY
operation"), this field is no longer used, so get rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This reverts commit e958e079e2 ("dmaengine: mic_x100: add missing
spin_unlock").
The above patch is incorrect. There is nothing wrong with the original
code. The spin_lock is acquired in the "prep" functions and released
in "submit".
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add support for providing device to filter_fn mapping so client drivers
can switch to use the dma_request_chan() API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The two API function can cover most, if not all current APIs used to
request a channel. With minimal effort dmaengine drivers, platforms and
dmaengine user drivers can be converted to use the two function.
struct dma_chan *dma_request_chan_by_mask(const dma_cap_mask_t *mask);
To request any channel matching with the requested capabilities, can be
used to request channel for memcpy, memset, xor, etc where no hardware
synchronization is needed.
struct dma_chan *dma_request_chan(struct device *dev, const char *name);
To request a slave channel. The dma_request_chan() will try to find the
channel via DT, ACPI or in case if the kernel booted in non DT/ACPI mode
it will use a filter lookup table and retrieves the needed information from
the dma_slave_map provided by the DMA drivers.
This legacy mode needs changes in platform code, in dmaengine drivers and
finally the dmaengine user drivers can be converted:
For each dmaengine driver an array of DMA device, slave and the parameter
for the filter function needs to be added:
static const struct dma_slave_map da830_edma_map[] = {
{ "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 0) },
{ "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 1) },
{ "davinci-mcasp.1", "rx", EDMA_FILTER_PARAM(0, 2) },
{ "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 3) },
{ "davinci-mcasp.2", "rx", EDMA_FILTER_PARAM(0, 4) },
{ "davinci-mcasp.2", "tx", EDMA_FILTER_PARAM(0, 5) },
{ "spi_davinci.0", "rx", EDMA_FILTER_PARAM(0, 14) },
{ "spi_davinci.0", "tx", EDMA_FILTER_PARAM(0, 15) },
{ "da830-mmc.0", "rx", EDMA_FILTER_PARAM(0, 16) },
{ "da830-mmc.0", "tx", EDMA_FILTER_PARAM(0, 17) },
{ "spi_davinci.1", "rx", EDMA_FILTER_PARAM(0, 18) },
{ "spi_davinci.1", "tx", EDMA_FILTER_PARAM(0, 19) },
};
This information is going to be needed by the dmaengine driver, so
modification to the platform_data is needed, and the driver map should be
added to the pdata of the DMA driver:
da8xx_edma0_pdata.slave_map = da830_edma_map;
da8xx_edma0_pdata.slavecnt = ARRAY_SIZE(da830_edma_map);
The DMA driver then needs to configure the needed device -> filter_fn
mapping before it registers with dma_async_device_register() :
ecc->dma_slave.filter_map.map = info->slave_map;
ecc->dma_slave.filter_map.mapcnt = info->slavecnt;
ecc->dma_slave.filter_map.fn = edma_filter_fn;
When neither DT or ACPI lookup is available the dma_request_chan() will
try to match the requester's device name with the filter_map's list of
device names, when a match found it will use the information from the
dma_slave_map to get the channel with the dma_get_channel() internal
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Channel matching with private_candidate() is used in two paths, the error
checking is slightly different in them and they are duplicating code also.
Move the code under find_candidate() to provide consistent execution and
going to allow us to reuse this mode of channel lookup later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If mask is NULL skip the mask matching against the DMA device capabilities.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use of the CANCEL bit in mdc_terminate_all creates an
additional 'command done' to appear in the registers (in
addition to an interrupt).
In addition, there is a potential race between
mdc_terminate_all and the irq handler if a transfer
completes at the same time as the terminate all (presently
this results in an inappropriate warning).
To handle these issues, any outstanding 'command done'
events are cleared during mdc_terminate_all and the irq
handler takes no action when there are no new 'command done'
events.
Signed-off-by: Damien.Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Due to changes in device and platform code drivers w/o probe will fail to
load. This means that the devices for eDMA TPTCs are goign to be without
driver and omap hwmod code will turn them off after the kernel finished
loading:
[ 3.015900] platform 49800000.tptc: omap_device_late_idle: enabled but no driver. Idling
[ 3.024671] platform 49a00000.tptc: omap_device_late_idle: enabled but no driver. Idling
This will prevent eDMA to work since the TPTCs are not enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes: 34635b1acc ("dmaengine: edma: Add dummy driver skeleton for edma3-tptc")
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If the "dma-channels" DT property is missing, the dw_dma_parse_dt()
function return NULL, but not before allocating memory for a struct
dw_dma_platform_data through devres. If the device supports parameter
detection, the probe still succeeds and the allocated memory is not
released until the device is removed.
Fix this by deferring the allocation until after checking the
"dma-channels" property.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch fixes at_xdmac_prep_dma_memcpy(). Indeed the data width field
of the Channel Configuration register was not updated properly in the
loop: the bits of the dwidth field were not cleared before adding their
new value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Fixes: e1f7c9eee7 ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver")
Cc: stable@vger.kernel.org #4.1 and later
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
'commit d8b468394f ("dmaengine: Add STM32 DMA driver")' leads to the
following Smatch complaint:
drivers/dma/stm32-dma.c:562 stm32_dma_issue_pending()
error: we previously assumed 'chan->desc' could be null (see line 560)
So, this patch fixes the unchecked dereference of chan->desc by returning
operation not permitted error when stm32_dma_start_transfer() does not
succeed to allocate a virtual channel descriptor.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As of commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), the Renesas R-Car HPB-DMAC driver is no longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that requires
adding DT support to the driver, which is not planned.
Remove the driver, it can be resurrected from git history when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The variable "res" will eventually be set to a resource pointer from
a call of the d40_hw_detect_init(() function.
Thus let us omit the explicit initialisation at the beginning.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
A single jump label was used by the d40_probe() function in several cases
for error handling which was a bit inefficient here.
* This implementation detail could be improved by the introduction
of another jump label.
* Remove an extra check for the variable "base".
* Omit its explicit initialisation at the beginning then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The kmem_cache_destroy() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On probe failure or driver removal, before killing any tasklets, ensure
that the channel interrupt is freed to ensure that another channel
interrupt cannot occur and schedule the tasklet again.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The tegra20-apb-dma driver currently uses the flag GFP_ATOMIC when
allocating memory for structures used in conjunction with the DMA
descriptors. It is preferred that dmaengine drivers use GFP_NOWAIT
instead and so the emergency memory pool will not be used by these
drivers.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
