Turbo mode allows to read data to shift register when rx-buffer
is full thus improving the perfomance. This feature is available
for RX-only mode.
In PIO turbo mode when the penultimate word is available
in RX-buffer the controller should be disabled before reading data
to prevent the next transaction triggering. The controller itself
handles the last word to be correctly loaded to shift-register and
then transferred to RX-buffer.
The turbo mode is enabled by setting turbo_mode parameter to 1.
This parameter is a part of omap2_mcspi_device_config structure
which is passed through the spi_device controller_data pointer.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The value 160 has been obtained as optimal in testing it for
wl1271 which use spi for communication.
In some sense this change might also influence on other spi devices
connected to omap2_mcspi controller.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fix prevents queue being marked as "stopped", if data exists
in the queue list.
Signed-off-by: Grzegorz Sygieda <grzegorz.sygieda@tieto.com>
Signed-off-by: Lukasz Baj <lukasz.baj@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds support for a further ST variant of the PL022 called
PL023. Some differences in the control registers due to being
stripped down to SPI mode only, and a new clock feedback sample
delay config setting is available.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PL022 SPI driver did not cleanly separate between the
original unmodified ARM version and the ST Microelectronics
versions. Split this more cleanly and fix some whitespace
moaning from checkpatch at the same time.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes a typo were map_tx_dma is used instead of
map_rx_dma, casing the driver to unmap rx_dma when it
shouldn't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
QE mode uses Little Endian so words > 8 bits are byte swapped.
Workaround this by always enforcing wordsize 8 for words
> 8 bits. Unfortunately this will not work for LSB transfers
where wordsize is > 8 bits so disable these for now.
Also move the different quirks into its own function to keep
mpc8xxx_spi_setup_transfer() sane.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Under abnormal termination, modify_qp() closes the QP, and async event
(AE) handling also attempts to close the same QP, causing a crash.
Fix this by checking the state of the QP before processing the AE.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enhance ethtool to read hardware registers for rcv/tx error stats.
Also add support for free pbl resources. Remove cq depth stats, which
are not used.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- wrap cq->cqidx_inc based on cq size.
- optimize t4_arm_cq logic.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
1) save the timestamp flit in the cq when we consume a CQE.
2) always compare the saved flit with the previous entry flit when
reading the next CQE entry. If the flits don't compare, then we
have overflowed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need 1 extra entry for the status page and 1 to always have 1 free
entry to detect when the queue is full.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LLD now supports proper UP state change events, so move the RDMA
provider registration to UP path.
This fixes a crash when loading iw_cxgb4 _after_ the NFS/RDMA
transport is up and running.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the RDMA core unregister path, kernel users will be calling down
into the T4 provider to release resources. So we cannot detach from
the LLD until this process completes.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes possible memory leak.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI function reset needs to invoked after fw init ioctl is issued.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because MIPS's EDQUOT value is 1133(0x46d).
It's larger than u8.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add audio support part in arch/arm/mach-w90x900
Signed-off-by: Wan ZongShun<mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an option to force usage of the in-kernel cmdline even if the boot
loader passes another command string to the kernel.
Useful if someone cannot or don't want to change the
command-line options of the boot loader but is able to change
the kernel.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The check for compiler which is supposed to miscompile unwind tables
clearly has nothing to do with sparse (which does not define necessary
macros anyway), so simply silence it.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/board-sam9m10g45ek.c: mach/hardware.h is included more than once
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/nwfpe/fpsr.h:33: ERROR: trailing whitespace
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-shark/pci.c:19: ERROR: trailing statements should be on next line
arch/arm/mach-shark/pci.c:20: ERROR: trailing statements should be on next line
arch/arm/mach-shark/pci.c:21: ERROR: trailing statements should be on next line
arch/arm/mach-shark/pci.c:24: WARNING: externs should be avoided in .c files
arch/arm/mach-shark/pci.c:28: WARNING: please, no space before tabs
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/nwfpe/ChangeLog:75: ERROR: trailing whitespace
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-sa1100/leds.c:21: ERROR: code indent should use tabs where possible
arch/arm/mach-sa1100/leds.c:21: WARNING: please, no space before tabs
arch/arm/mach-sa1100/leds.c:22: ERROR: code indent should use tabs where possible
arch/arm/mach-sa1100/leds.c:22: WARNING: please, no space before tabs
arch/arm/mach-sa1100/leds.c:24: ERROR: code indent should use tabs where possible
arch/arm/mach-sa1100/leds.c:24: WARNING: please, no space before tabs
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-h720x/common.h:17: WARNING: space prohibited between function name and open parenthesis '('
arch/arm/mach-h720x/common.h:23: WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-footbridge/ebsa285-pci.c:22: ERROR: switch and case should be at the same indent
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-clps711x/Makefile.boot:2: ERROR: trailing whitespace
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/boot/bootp/bootp.lds:22: ERROR: trailing whitespace
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove duplicated #include('s) in
arch/arm/mach-spear6xx/spear6xx.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The functionality to keep the device awake until it is done with
the rx of any mcast/bcast frames which are pending on AP should
also be added to the hardwares which support auto sleep feature.
This patch fixes frequent failures in ARP resolution when it is
initiated by the other end. Currently auto sleep is enabled only
for ar9003 in ath9k.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sta_info.h kernel-doc warnings:
Warning(net/mac80211/sta_info.h:164): No description found for parameter 'tid_active_rx[STA_TID_NUM]'
Warning(net/mac80211/sta_info.h:164): Excess struct/union/enum/typedef member 'tid_state_rx' description in 'sta_ampdu_mlme'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix kernel-doc warnings in mac80211.h:
Warning(include/net/mac80211.h:838): No description found for parameter 'ap_addr'
Warning(include/net/mac80211.h:1726): No description found for parameter 'get_survey'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The intent here is to test that "sta_id_r" is a valid pointer. We do
this same test later on in the function.
Btw iwl_add_bssid_station() is called from two places and "sta_id_r" is
a valid pointer from both callers.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is obviously a small picky thing. The original error handling code
doesn't free the most recent allocations which haven't been added to the
hif_dev->tx.tx_buf list yet.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After c11d8f89d3: "ath9k_htc: Simplify TX URB management" we no longer
assume that tx_buf is a non-null pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent changes to skb handling introduced a bug in the rt2800usb
TX descriptor writing whereby the length of the USB packet wasn't
calculated correctly.
Found via code inspection, as the devices themselves didn't seem to mind.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Based on a patch created by Ondrej Zary)
In some circumstances the Ralink devices do not properly go to sleep
or wake up, with timeouts occurring.
Fix this by retrying telling the device that it has to wake up or
sleep.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 03ceedea97.
This patch was reported to cause a regression in which connectivity is
lost and cannot be reestablished after a suspend/resume cycle.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
