When CONFIG_USB_ISP1761_UDC is not enabled the udc_enabled variable is
never used since it is short circuited before in the logic operations.
This would trigger the following warning by clang analyzer:
drivers/usb/isp1760/isp1760-core.c:490:2: warning: Value stored to 'udc_enabled' is never read [clang-analyzer-deadcode.DeadStores]
udc_enabled = ((devflags & ISP1760_FLAG_ISP1763) ||
^
drivers/usb/isp1760/isp1760-core.c:490:2: note: Value stored to 'udc_enabled' is never read
Just swap the other of the operands in the logic operations.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-6-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though it is not expected, and would trigger a WARN_ON, killing a
transfer in a uninitialized slot this sequence is warned by clang
analyzer, twice:
drivers/usb/isp1760/isp1760-hcd.c:1976:18: warning: The result of the left shift is undefined because the right operand is negative [clang-analyzer-core.UndefinedBinaryOperatorResult]
skip_map |= (1 << qh->slot);
drivers/usb/isp1760/isp1760-hcd.c:1983:18: warning: The result of the left shift is undefined because the right operand is negative [clang-analyzer-core.UndefinedBinaryOperatorResult]
skip_map |= (1 << qh->slot);
Only set skip map if slot is active.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-5-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not really need to reset retval before get used bellow.
This will avoid the clang-analyzer warning:
drivers/usb/isp1760/isp1760-hcd.c:1919:2: warning: Value stored to 'retval' is never read [clang-analyzer-deadcode.DeadStores]
retval = 0;
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When checking if we need one more packet on a bulk pipe we may, even
though not probable at all, get there with a zero maxpacketsize.
In that case for sure no packet, no even a one more, will be
allocated.
This will clean the clang-analyzer warning:
drivers/usb/isp1760/isp1760-hcd.c:1856:38: warning: Division by zero [clang-analyzer-core.DivideZero]
&& !(urb->transfer_buffer_length %
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not care about the return value of that read between the
scratch register write and read, we really just want to make sure that
the pattern in the bus get changed to make sure we are testing
correctly the scratch pattern.
Clang-analyzer complains about the never read scratch variable:
>> drivers/usb/isp1760/isp1760-hcd.c:735:2: warning: Value stored to 'scratch' is never read [clang-analyzer-deadcode.DeadStores]
scratch = isp1760_hcd_read(hcd, HC_CHIP_ID_HIGH);
Just ignore the return value of that CHIP_ID_HIGH read, add more
information to the comment above why we are doing this. And as at it,
just do a small format change in the error message bellow.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-2-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The description for "qlen" is missing, and there is a description
for this parameter in "Documentation/usb/gadget_printer.rst"
Signed-off-by: Wei Ming Chen <jj251510319013@gmail.com>
Link: https://lore.kernel.org/r/20210821142647.2904-1-jj251510319013@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a remote usb device is attached to the local Virtual USB
Host Controller Root Hub port, the bound device driver may send
a port reset command.
vhci_hcd accepts port resets only when the device doesn't have
port address assigned to it. When reset happens device is in
assigned/used state and vhci_hcd rejects it leaving the port in
a stuck state.
This problem was found when a blue-tooth or xbox wireless dongle
was passed through using usbip.
A few drivers reset the port during probe including mt76 driver
specific to this bug report. Fix the problem with a change to
honor reset requests when device is in used state (VDEV_ST_USED).
Reported-and-tested-by: Michael <msbroadf@gmail.com>
Suggested-by: Michael <msbroadf@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210819225937.41037-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cleanup code for unlink_tx and unlink_rx lists is almost the same.
So, extract it into a new function and call it for both unlink_rx and
unlink_tx. Also, remove unnecessary log messages.
Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com>
Link: https://lore.kernel.org/r/20210820190122.16379-3-mail@anirudhrb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IRQ occurs between calling dsps_setup_optional_vbus_irq()
and dsps_create_musb_pdev(), then null pointer dereference occurs
since glue->musb wasn't initialized yet.
The patch puts initializing of neccesery data before registration
of the interrupt handler.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819163323.17714-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD's latest platforms has DWC3 controller. Add the PCI ID and
properties for the same.
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20210823184449.2796184-2-Nehal-Bakulchandra.shah@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IRQ occurs between calling devm_request_threaded_irq() and
initializing dwc3_imx->dwc3, then null pointer dereference occurs
since dwc3_imx->dwc3 is used in dwc3_imx8mp_interrupt().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210819154818.18334-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee ("ARM: Orion: EHCI: Add support for enabling clocks")
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we register two usb buses for each xHC, and systems with several
hosts are more and more common it is getting hard to follow the
flow of debug messages without knowing which bus they belong to
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add more debugging messages to follow what happends to a URB internally
in special cases like URB cancel, halted endpoints and endpoint reset.
Helps tracking issues like URB never given back by host.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5d5323a6f3.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only TDs with status TD_CLEARING_CACHE will be given back after
cache is cleared with a set TR deq command.
xhci_invalidate_cached_td() failed to set the TD_CLEARING_CACHE status
for some cancelled TDs as it assumed an endpoint only needs to clear the
TD it stopped on.
This isn't always true. For example with streams enabled an endpoint may
have several stream rings, each stopping on a different TDs.
Note that if an endpoint has several stream rings, the current code
will still only clear the cache of the stream pointed to by the last
cancelled TD in the cancel list.
This patch only focus on making sure all canceled TDs are given back,
avoiding hung task after device removal.
Another fix to solve clearing the caches of all stream rings with
cancelled TDs is needed, but not as urgent.
This issue was simultanously discovered and debugged by
by Tao Wang, with a slightly different fix proposal.
Fixes: 674f8438c1 ("xhci: split handling halted endpoints into two steps")
Cc: <stable@vger.kernel.org> #5.12
Reported-by: Tao Wang <wat@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_ctrl_ctx()
xhci_decode_slot_context()
xhci_decode_usbsts()
xhci_decode_doorbell()
xhci_decode_ep_context()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor changes are needed in other xhci code as these functions are also
used elsewhere
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes static char buffer usage in the following decode functions:
xhci_decode_trb()
xhci_decode_ptortsc()
Caller must provide a buffer to use.
In tracing use __get_str() as recommended to pass buffer.
Minor chanes are needed in xhci debugfs code as these functions are also
used there. Changes include moving XHCI_MSG_MAX definititon from
xhci-trace.h to xhci.h
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace symbolic permission macros with octal permission numbers
because octal permission numbers are easier to read and understand
instead of their symbolic macro names.
No functional change.
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Utkarsh Verma <utkarshverma294@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 3c18e9baee.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
Reported-by: Paul Größel <pb.g@gmx.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214131
Fixes: 3c18e9baee ("USB: serial: ch341: fix character loss at high transfer rates")
Cc: stable@vger.kernel.org
Cc: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210824121926.19311-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
f_hid provides the OUT Endpoint as only way for receiving reports
from the host. SETUP/SET_REPORT method is not supported, and this causes
a number of compatibility problems with various host drivers, especially
in the case of keyboard emulation using f_hid.
- Some hosts do not support the OUT Endpoint and ignore it,
so it becomes impossible for the gadget to receive a report
from the host. In the case of a keyboard, the gadget loses
the ability to receive the status of the LEDs.
- Some BIOSes/UEFIs can't work with HID devices with the OUT Endpoint
at all. This may be due to their bugs or incomplete implementation
of the HID standard.
For example, absolutely all Apple UEFIs can't handle the OUT Endpoint
if it goes after IN Endpoint in the descriptor and require the reverse
order (OUT, IN) which is a violation of the standard.
Other hosts either do not initialize gadgets with a descriptor
containing the OUT Endpoint completely (like some HP and DELL BIOSes
and embedded firmwares like on KVM switches), or initialize them,
but will not poll the IN Endpoint.
This patch adds configfs option no_out_endpoint=1 to disable
the OUT Endpoint and allows f_hid to receive reports from the host
via SETUP/SET_REPORT.
Previously, there was such a feature in f_hid, but it was replaced
by the OUT Endpoint [1] in the commit 99c5150058 ("usb: gadget: hidg:
register OUT INT endpoint for SET_REPORT"). So this patch actually
returns the removed functionality while making it optional.
For backward compatibility reasons, the OUT Endpoint mode remains
the default behaviour.
- The OUT Endpoint mode provides the report queue and reduces
USB overhead (eliminating SETUP routine) on transmitting a report
from the host.
- If the SETUP/SET_REPORT mode is used, there is no report queue,
so the userspace will only read last report. For classic HID devices
like keyboards this is not a problem, since it's intended to transmit
the status of the LEDs and only the last report is important.
This mode provides better compatibility with strange and buggy
host drivers.
Both modes passed USBCV tests. Checking with the USB protocol analyzer
also confirmed that everything is working as it should and the new mode
ensures operability in all of the described cases.
Link: https://www.spinics.net/lists/linux-usb/msg65494.html [1]
Reviewed-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210821134004.363217-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If wIndex is 0 (and it often is), these calculations underflow and
UBSAN complains, here resolve this by not decrementing the index when
it is equal to 0, this copies the solution from commit 85e3990bea
("USB: EHCI: avoid undefined pointer arithmetic and placate UBSAN")
Reported-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1624004938-2399-1-git-send-email-jun.li@nxp.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Refactor struct ehci_regs to avoid accessing beyond the end of
port_status. This change results in no difference in the final
object code.
Avoids several warnings when building with -Warray-bounds:
drivers/usb/host/ehci-brcm.c: In function 'ehci_brcm_reset':
drivers/usb/host/ehci-brcm.c:113:32: warning: array subscript 16 is above array bounds of 'u32[15]' {aka 'unsigned int[15]'} [-Warray-bounds]
113 | ehci_writel(ehci, 0x00800040, &ehci->regs->port_status[0x10]);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/ehci.h:274,
from drivers/usb/host/ehci-brcm.c:15:
./include/linux/usb/ehci_def.h:132:7: note: while referencing 'port_status'
132 | u32 port_status[HCS_N_PORTS_MAX];
| ^~~~~~~~~~~
Note that the documentation around this proprietary register was
confusing. If "USB_EHCI_INSNREG00" is at port_status[0x0f], its offset
would be 0x80 (not 0x90). The comments have been adjusted to fix this
apparent typo.
Fixes: 9df231511b ("usb: ehci: Add new EHCI driver for Broadcom STB SoC's")
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20210818173018.2259231-3-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IRQ occurs between calling request_irq() and mv_u3d_eps_init(),
then null pointer dereference occurs since u3d->eps[] wasn't
initialized yet but used in mv_u3d_nuke().
The patch puts registration of the interrupt handler after
initializing of neccesery data.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 90fccb529d ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210818141247.4794-1-lutovinova@ispras.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a20dcf53ea ("usb: typec: tcpm: Respond Not_Supported if no
snk_vdo"), stops tcpm_pd_data_request() calling tcpm_handle_vdm_request()
when port->nr_snk_vdo is not set. But the VDM might be intended for an
altmode-driver, in which case nr_snk_vdo does not matter.
This change breaks the forwarding of connector hotplug (HPD) events
for displayport altmode on devices which don't set nr_snk_vdo.
tcpm_pd_data_request() is the only caller of tcpm_handle_vdm_request(),
so we can move the nr_snk_vdo check to inside it, at which point we
have already looked up the altmode device so we can check for this too.
Doing this check here also ensures that vdm_state gets set to
VDM_STATE_DONE if it was VDM_STATE_BUSY, even if we end up with
responding with PD_MSG_CTRL_NOT_SUPP later.
Note that tcpm_handle_vdm_request() was already sending
PD_MSG_CTRL_NOT_SUPP in some circumstances, after moving the nr_snk_vdo
check the same error-path is now taken when that check fails. So that
we have only one error-path for this and not two. Replace the
tcpm_queue_message(PD_MSG_CTRL_NOT_SUPP) used by the existing error-path
with the more robust tcpm_pd_handle_msg() from the (now removed) second
error-path.
Fixes: a20dcf53ea ("usb: typec: tcpm: Respond Not_Supported if no snk_vdo")
Cc: stable <stable@vger.kernel.org>
Cc: Kyle Tso <kyletso@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210816154632.381968-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7583b63c34 ("powerpc/40x: Remove STB03xxx") removes the config
STB03xxx, but left a reference in ./drivers/usb/Kconfig behind.
Hence, ./scripts/checkkconfigsymbols.py warns:
STB03xxx
Referencing files: drivers/usb/Kconfig
Remove this reference to the deleted config.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210818071137.22711-4-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 71ed79b0e4 ("USB: Move wusbcore and UWB to staging as it is
obsolete") misses to adjust some part in ./drivers/usb/host/Makefile.
Hence, ./scripts/checkkconfigsymbols.py warns:
USB_HWA_HCD
Referencing files: drivers/usb/Makefile
Remove the missing piece of this code removal.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210818071137.22711-3-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1b00767fd8 ("MIPS: Remove PMC MSP71xx platform") deletes
./arch/mips/pmcs-msp71xx/Kconfig, including its config MSP_HAS_USB.
Hence, since then, the corresponding EHCI support for on-chip PMC MSP71xx
USB controller is dead code. Remove this dead driver.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20210818071137.22711-2-lukas.bulwahn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DWC_usb3 revisions 3.00a and newer (including DWC_usb31 and
DWC_usb32) the GUCTL1 register gained the DEV_DECOUPLE_L1L2_EVT
field (bit 31) which when enabled allows the controller in device
mode to treat USB 2.0 L1 LPM & L2 events separately.
After commit d1d90dd272 ("usb: dwc3: gadget: Enable suspend
events") the controller will now receive events (and therefore
interrupts) for every state change when entering/exiting either
L1 or L2 states. Since L1 is handled entirely by the hardware
and requires no software intervention, there is no need to even
enable these events and unnecessarily notify the gadget driver.
Enable the aforementioned bit to help reduce the overall interrupt
count for these L1 events that don't need to be handled while
retaining the events for full L2 suspend/wakeup.
Tested-by: Jun Li <jun.li@nxp.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org> # for RB5 (sm8250)
Tested-by: John Stultz <john.stultz@linaro.org> # for HiKey960 & db845c
Reviewed-by: Jun Li <jun.li@nxp.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Link: https://lore.kernel.org/r/20210812082635.12924-1-jackp@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding an
original error code. Stop calling request_threaded_irq() with the invalid
IRQ #s.
Fixes: 9ba96ae507 ("usb: omap1: Tahvo USB transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8280d6a4-8e9a-7cfe-1aa9-db586dc9afdf@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to usb_add_hcd() (which takes
*unsigned* IRQ #), causing request_irq() that it calls to fail with
-EINVAL, overriding an original error code. Stop calling usb_add_hcd()
with the invalid IRQ #s.
Fixes: 78c73414f4 ("USB: ohci: add support for tmio-ohci cell")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/402e1a45-a0a4-0e08-566a-7ca1331506b1@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
soc_device_match() is intended as a last resort, to handle e.g. quirks
that cannot be handled by matching based on a compatible value.
As the device nodes for the Renesas USB 3.0 Peripheral Controller on
R-Car E3 and RZ/G2E do have SoC-specific compatible values, the latter
can and should be used to match against these devices.
This also fixes support for the USB 3.0 Peripheral Controller on the
R-Car E3e (R8A779M6) SoC, which is a different grading of the R-Car E3
(R8A77990) SoC, using the same SoC-specific compatible value.
Fixes: 30025efa8b ("usb: gadget: udc: renesas_usb3: add support for r8a77990")
Fixes: 546970fdab ("usb: gadget: udc: renesas_usb3: add support for r8a774c0")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/760981fb4cd110d7cbfc9dcffa365e7c8b25c6e5.1628696960.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the Type-C controller supports PD, it is doable to disable PD
capabilities with the current state machine in TCPM. Without enabling RX
in low-level drivers and with skipping the power negotiation, the port
is eligible to be a non-PD Type-C port. Use new flags whose values are
populated from the device tree to decide the port PD capability. Adding
"pd-disable" property in device tree indicates that the port does not
support PD. If PD is not supported, the device tree property
"typec-power-opmode" shall be added to specify the advertised Rp value
if the port supports SRC role.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210804081917.3390341-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_endpoint_maxp() only returns the bit[10:0] of wMaxPacketSize
of endpoint descriptor, not includes bit[12:11] anymore, so use
usb_endpoint_maxp_mult() instead.
Meanwhile no need AND 0x7ff when get maxp, remove it.
Fixes: 49db427232 ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_endpoint_maxp() only returns the bit[10:0] of wMaxPacketSize
of endpoint descriptor, not include bit[12:11] anymore, so use
usb_endpoint_maxp_mult() instead.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code. Stop calling request_threaded_irq() with the
invalid IRQ #s.
Fixes: c33fad0c37 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/9507f50b-50f1-6dc4-f57c-3ed4e53a1c25@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 0807c500a1 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/b0a86089-8b8b-122e-fd6d-73e8c2304964@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 517c4c44b3 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/806d0b1a-365b-93d9-3fc1-922105ca5e61@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 188db4435a ("usb: gadget: s3c: use platform resources")
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/bd69b22c-b484-5a1f-c798-78d4b78405f2@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 8b2e76687b ("USB: AT91 UDC updates, mostly power management")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/6654a224-739a-1a80-12f0-76d920f87b6c@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dwc3_qcom_acpi_register_core(), the driver neglects to check the result
of platform_get_irq()'s call and blithely assigns the negative error codes
to the allocated child device's IRQ resource and then passing this resource
to platform_device_add_resources() and later causing dwc3_otg_get_irq() to
fail anyway. Stop calling platform_device_add_resources() with the invalid
IRQ #s, so that there's less complexity in the IRQ error checking.
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/45fec3da-1679-5bfe-5d74-219ca3fb28e7@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_threaded_irq()
(which takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_threaded_irq() with the
invalid IRQ #s.
Fixes: f90db10779 ("usb: dwc3: meson-g12a: Add support for IRQ based OTG switching")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/96106462-5538-0b2f-f2ab-ee56e4853912@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare for removal of the request pointer by using scsi_cmd_to_rq()
instead. This patch does not change any functionality.
Link: https://lore.kernel.org/r/20210809230355.8186-52-bvanassche@acm.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This reverts commit d25d85061b as it is
reported to cause problems on many different types of boards.
Reported-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Ray Chi <raychi@google.com>
Link: https://lore.kernel.org/r/CANcMJZCEVxVLyFgLwK98hqBEdc0_n4P0x_K6Gih8zNH3ouzbJQ@mail.gmail.com
Fixes: d25d85061b ("usb: dwc3: gadget: Use list_replace_init() before traversing lists")
Cc: stable <stable@vger.kernel.org>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Wesley Cheng <wcheng@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently xhci-mtk needs software-managed bandwidth allocation for
periodic endpoints, it allocates the microframe index for the first
start-split packet for each endpoint. As this index allocation logic
should avoid the conflicts with other full/low-speed periodic endpoints,
it uses the worst case byte budgets on high-speed bus bandwidth
For example, for an isochronos IN endpoint with 192 bytes budget,
it will consume the whole 4 u-frames(188 * 4) while the actual
full-speed bus budget should be just 192bytes.
This patch changes the low/full-speed bandwidth allocation logic
to use "approximate" best case budget for lower speed bandwidth
management. For the same endpoint from the above example, the
approximate best case budget is now reduced to (188 * 2) bytes.
Without this patch, many usb audio headsets with 3 interfaces
(audio input, audio output, and HID) cannot be configured
on xhci-mtk.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133937.1.Ia8174b875bc926c12ce427a5a1415dea31cc35ae@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci-mtk depends on xhci's internal virt_dev when it retrieves its
internal data from usb_host_endpoint both in add_endpoint and
drop_endpoint callbacks. But when setup packet was retired by
transaction errors in xhci_setup_device() path, a virt_dev for the slot
is newly created with real_port 0. This leads to xhci-mtks's NULL pointer
dereference from drop_endpoint callback as xhci-mtk assumes that virt_dev's
real_port is always started from one. The similar problems were addressed
by [1] but that can't cover the failure cases from setup_device.
This patch drops the usages of xhci's virt_dev in xhci-mtk's drop_endpoint
callback by adopting rhashtable for searching mtk's schedule entity
from a given usb_host_endpoint pointer instead of searching a linked list.
So mtk's drop_endpoint callback doesn't have to rely on virt_dev at all.
[1] https://lore.kernel.org/r/1617179142-2681-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210805133731.1.Icc0f080e75b1312692d4c7c7d25e7df9fe1a05c2@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer i_feature is being initialized with a value and then immediately
re-assigned a new value in the next statement. Fix this by replacing the
the redundant initialization with the following assigned value.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210804125907.111654-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use swap() in order to make code cleaner. Issue found by coccinelle.
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Link: https://lore.kernel.org/r/20210803005343.GA1578854@pc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the cast done by ERR_PTR() and PTR_ERR() since data is of type char
* and fss_prepare_buffer() should returns a value of this type.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Link: https://lore.kernel.org/r/20210731171838.GA912463@pc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving FRS and Sourcing_Vbus events from low-level drivers, keep
other events which come a bit earlier so that they will not be ignored
in the event handler.
Fixes: 8dc4bd0736 ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)")
Cc: stable <stable@vger.kernel.org>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210803091314.3051302-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
usb_gadget_remove_driver()
-->usb_gadget_disconnect()
-->dwc3_gadget_pullup(0)
-->pm_runtime_get_sync() -> ret = 0
-->pm_runtime_put() [async]
-->usb_gadget_udc_stop()
-->dwc3_gadget_stop()
-->dwc->gadget_driver = NULL
...
dwc3_suspend_common()
-->dwc3_gadget_suspend()
-->DWC3 halt/stop routine skipped, driver_data == NULL
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
Fixes: 77adb8bdf4 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1628058245-30692-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The list_for_each_entry_safe() macro saves the current item (n) and
the item after (n+1), so that n can be safely removed without
corrupting the list. However, when traversing the list and removing
items using gadget giveback, the DWC3 lock is briefly released,
allowing other routines to execute. There is a situation where, while
items are being removed from the cancelled_list using
dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable
routine is running in parallel (due to UDC unbind). As the cleanup
routine removes n, and the pullup disable removes n+1, once the
cleanup retakes the DWC3 lock, it references a request who was already
removed/handled. With list debug enabled, this leads to a panic.
Ensure all instances of the macro are replaced where gadget giveback
is used.
Example call stack:
Thread#1:
__dwc3_gadget_ep_set_halt() - CLEAR HALT
-> dwc3_gadget_ep_cleanup_cancelled_requests()
->list_for_each_entry_safe()
->dwc3_gadget_giveback(n)
->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list]
->spin_unlock
->Thread#2 executes
...
->dwc3_gadget_giveback(n+1)
->Already removed!
Thread#2:
dwc3_gadget_pullup()
->waiting for dwc3 spin_lock
...
->Thread#1 released lock
->dwc3_stop_active_transfers()
->dwc3_remove_requests()
->fetches n+1 item from cancelled_list (n removed by Thread#1)
->dwc3_gadget_giveback()
->dwc3_gadget_del_and_unmap_request()- n+1
deleted[cancelled_list]
->spin_unlock
Fix this condition by utilizing list_replace_init(), and traversing
through a local copy of the current elements in the endpoint lists.
This will also set the parent list as empty, so if another thread is
also looping through the list, it will be empty on the next iteration.
Fixes: d4f1afe5e8 ("usb: dwc3: gadget: move requests to cancelled_list")
Cc: stable <stable@vger.kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1627543994-20327-1-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are two type-detection regression fixes for pl2303 and a patch to
increase the receive buffer size for for ch341 to avoid lost characters
at high line speeds.
Included are also some new device ids.
All but the last three commits have been in linux-next and with no
reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYQujDwAKCRALxc3C7H1l
CN84AP97UMs0lyLQjHsLMxBJonpukAddo0Um3B3tEppy+Vhm5QEAixXRw5l9HkrL
iqPFeBi9G6B9HNtCb8x4+ezfq7b94AA=
=yJ8B
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.14-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.14-rc5
Here are two type-detection regression fixes for pl2303 and a patch to
increase the receive buffer size for for ch341 to avoid lost characters
at high line speeds.
Included are also some new device ids.
All but the last three commits have been in linux-next and with no
reported issues.
* tag 'usb-serial-5.14-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: ftdi_sio: add device ID for Auto-M3 OP-COM v2
USB: serial: pl2303: fix GT type detection
USB: serial: option: add Telit FD980 composition 0x1056
USB: serial: pl2303: fix HX type detection
USB: serial: ch341: fix character loss at high transfer rates
The Auto-M3 OP-COM v2 is a OBD diagnostic device using a FTD232 for the
USB connection.
Signed-off-by: David Bauer <mail@david-bauer.net>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
At least some PL2303GT have a bcdDevice of 0x305 instead of 0x100 as the
datasheet claims. Add it to the list of known release numbers for the
HXN (G) type.
Fixes: 894758d057 ("USB: serial: pl2303: tighten type HXN (G) detection")
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com>
Cc: stable@vger.kernel.org # 5.13
Link: https://lore.kernel.org/r/20210804093100.24811-1-johan@kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
CP2105, CP2108 and CP2102N have vendor requests that can be used to
retrieve the firmware version. Having this information available is
essential when trying to work around buggy firmware as a recent CP2102N
regression showed.
Determine and log the firmware version also for CP2105 and CP2108
during type detection at probe.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up attach somewhat by moving type detection into the quirk helper
and giving it a more generic name.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the generic control request helper to implement the SET_CHARS
request.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
For consistency use the USB_CTRL_GET_TIMEOUT define for the
read-register request timeout (same value as USB_CTRL_SET_TIMEOUT).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure that the driver crtscts state is not updated in the unlikely
event that the flow-control request fails. Not doing so could break RTS
control.
Fixes: 5951b85088 ("USB: serial: cp210x: suppress modem-control errors")
Cc: stable@vger.kernel.org # 5.11
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
In the unlikely event that setting the software flow-control characters
fails the other flow-control settings should still be updated (just like
all other terminal settings).
Move out the error message printed by the set_chars() helper to make it
more obvious that this is intentional.
Fixes: 7748feffcd ("USB: serial: cp210x: add support for software flow control")
Cc: stable@vger.kernel.org # 5.11
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The device release number for HX-type devices is configurable in
EEPROM/OTPROM and cannot be used reliably for type detection.
Assume all (non-H) devices with bcdUSB 1.1 and unknown bcdDevice to be
of HX type while adding a bcdDevice check for HXD and TB (1.1 and 2.0,
respectively).
Reported-by: Chris <chris@cyber-anlage.de>
Fixes: 8a7bf7510d ("USB: serial: pl2303: amend and tighten type detection")
Cc: stable@vger.kernel.org # 5.13
Link: https://lore.kernel.org/r/20210730122156.718-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The struct pxa25x_ep_ops is only assigned to the ops field in the
usb_ep struct, which is a pointer to const struct usb_ep_ops.
Make it const to allow the compiler to put it in read-only memory.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210728092052.4178-1-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Willy Tarreau <w@1wt.eu>
Link: https://lore.kernel.org/r/20210724152739.18726-1-w@1wt.eu
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEDaZUZmFxRG/wNThrSFkpgVDWcbsFAmECS4kACgkQSFkpgVDW
cbtHIggAncAYLpf66mdiF/+uxXEIZ9wWRnB5E26o70Wpx+tFohtn/Qf9p5LWRB1y
NXDRXzf5l6pokyfzovbbw68ONEuMX8Vh5w/93Zrk1TuDmVN3cx/Tk6D7LUdVr0ZU
q1GHU21+sRV4a6UzXi6ByJKSukYYebncxYosuI6JzkeQpixq5mJW0/5J483qIKHK
F/BrdPpy+J27g8xBZRlBiG1jXhRKMiYx8++dLvUlsOMez4VLxfEz3IOlvsebMxW4
6TI6l1URPiIgoDgC7utOLWclgHFsMHVZiFjtqm8zznrEaxO9zeqsmzZYjm2a/+8u
FjAG9KZ5lIsgOf0Mx6vRxOL5aVSZPg==
=2upV
-----END PGP SIGNATURE-----
Merge tag 'usb-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Several small bug-fixes for cdns3 and cdnsp driver
* tag 'usb-v5.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: cdnsp: Fix the IMAN_IE_SET and IMAN_IE_CLEAR macro
usb: cdnsp: Fixed issue with ZLP
usb: cdnsp: Fix incorrect supported maximum speed
usb: cdns3: Fixed incorrect gadget state
IMAN_IE is BIT(1), so these macro are respectively equivalent to BIT(1)
and 0, whatever the value of 'p'.
The purpose was to set and reset a single bit in 'p'.
Fix these macros to do that correctly.
Acked-by: Pawel Laszczak <pawell@cadence.com>
Fixes: e93e58d274 ("usb: cdnsp: Device side header file for CDNSP driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d12bfcc9cbffb89e27b120668821b3c4f09b6755.1624390584.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Peter Chen <peter.chen@kernel.org>
The condition "if (need_zero_pkt && zero_len_trb)" was always false
and it caused that TRB for ZLP was not prepared.
Fix causes that after preparing last TRB in TD, the driver prepares
additional TD with ZLP when a ZLP is required.
Cc: <stable@vger.kernel.org>
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210623072728.41275-1-pawell@gli-login.cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
Driver had hardcoded in initialization maximum supported speed
to USB_SPEED_SUPER_PLUS but it should consider the speed
returned from usb_get_maximum_speed function.
Fixes: 3d82904559 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210625102502.26336-1-pawell@gli-login.cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
For delayed status phase, the usb_gadget->state was set
to USB_STATE_ADDRESS and it has never been updated to
USB_STATE_CONFIGURED.
Patch updates the gadget state to correct USB_STATE_CONFIGURED.
As a result of this bug the controller was not able to enter to
Test Mode while using MSC function.
Cc: <stable@vger.kernel.org>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20210623070247.46151-1-pawell@gli-login.cadence.com
Signed-off-by: Peter Chen <peter.chen@kernel.org>
SET_IDLE value must be shifted 8 bits to the right to get duration.
This confirmed by USBCV test.
Fixes: afcff6dc69 ("usb: gadget: f_hid: added GET_IDLE and SET_IDLE handlers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Maxim Devaev <mdevaev@gmail.com>
Link: https://lore.kernel.org/r/20210727185800.43796-1-mdevaev@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SAMA7G5 suspending ports will cut the access to OHCI registers and
any subsequent access to them will lead to CPU being blocked trying to
access that memory. Same thing happens on resume: if OHCI memory is
accessed before resuming ports the CPU will block on that access. The
OCHI memory is accessed on suspend/resume though
ohci_suspend()/ohci_resume().
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210721132905.1970713-1-claudiu.beznea@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the USB PHYs typically are on I2C or SPI bus for the 2430 glue layer,
we need configure the PHYs early for suspend.
The musb glue layer we need to suspend only after musb_suspend() in
suspend_late.
Fixes: 62d472d8ad ("usb: musb: Add missing PM suspend and resume functions for 2430 glue")
Reported-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727104134.52800-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to create qtd cache we were not destroying the
urb_listitem, rework the error handling logic to cope with that.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210727100516.4190681-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When polling for a setup or clear of a register field we were sleeping
in atomic context but using a very tight sleep interval.
Since the use cases for this poll mechanism are only in setup and
stop paths, and in practice this poll is not used most of the times
but needs to be there to comply to hardware setup times, remove the
sleep time and make the poll loop tighter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210727100516.4190681-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With usb3 we handle many more requests. Decrease the interrupt load by
only enabling the interrupt every quarter of the allocated requests.
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
--
v1 -> v2: - edited patch description
- removed extra parantheses
- added a comment for the logic
- using unsigned int instead of int
- reinitializing req_int_count in uvcg_video_enable
v2 -> v3: -
Link: https://lore.kernel.org/r/20210628155311.16762-6-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for scatter gather transfers. If the underlying
gadgets sg_supported == true, then the videeobuf2-dma-sg is used and the
encode routine maps all scatter entries to separate scatterlists for the
usb gadget.
When streaming 1080p with request size of 1024 times 3 bytes top shows a
difference of about 6.4% CPU load applying this patch:
PID USER PR NI VIRT RES %CPU %MEM TIME+ S COMMAND
64 root 0 -20 0.0m 0.0m 7.7 0.0 0:01.25 I [kworker/u5:0-uvcvideo]
83 root 0 -20 0.0m 0.0m 4.5 0.0 0:03.71 I [kworker/u5:3-uvcvideo]
307 root -51 0 0.0m 0.0m 3.8 0.0 0:01.05 S [irq/51-dwc3]
vs.
64 root 0 -20 0.0m 0.0m 5.8 0.0 0:01.79 I [kworker/u5:0-uvcvideo]
306 root -51 0 0.0m 0.0m 3.2 0.0 0:01.97 S [irq/51-dwc3]
82 root 0 -20 0.0m 0.0m 0.6 0.0 0:01.86 I [kworker/u5:1-uvcvideo]
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20210628155311.16762-5-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While sending bigger images is possible with USB_SPEED_SUPER it is
better to use more isochronous requests in flight. This patch makes the
number uvc_num_requests dynamic by changing it depending on the gadget
speed.
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20210628155311.16762-3-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of dwc3 it is possible that the sysdev is the parent of the
controller. To ensure the right dev is set to the gadget's dev parent we
will hand over sysdev instead of dev, which will always point to the
controller.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20210628155311.16762-2-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
