Recent changes to the link synchronization means that we can now just
drop packets arriving on the synchronizing link before the synch point
is reached. This has lead to significant simplifications to the
implementation, but also turns out to have a flip side that we need
to consider.
Under unlucky circumstances, the two endpoints may end up
repeatedly dropping each other's packets, while immediately
asking for retransmission of the same packets, just to drop
them once more. This pattern will eventually be broken when
the synch point is reached on the other link, but before that,
the endpoints may have arrived at the retransmission limit
(stale counter) that indicates that the link should be broken.
We see this happen at rare occasions.
The fix for this is to not ask for retransmissions when a link is in
state LINK_SYNCHING. The fact that the link has reached this state
means that it has already received the first SYNCH packet, and that it
knows the synch point. Hence, it doesn't need any more packets until the
other link has reached the synch point, whereafter it can go ahead and
ask for the missing packets.
However, because of the reduced traffic on the synching link that
follows this change, it may now take longer to discover that the
synch point has been reached. We compensate for this by letting all
packets, on any of the links, trig a check for synchronization
termination. This is possible because the packets themselves don't
contain any information that is needed for discovering this condition.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we introduced the new link failover/synch mechanism
in commit 6e498158a8
("tipc: move link synch and failover to link aggregation level"),
we missed the case when the non-tunnel link goes down during the link
synchronization period. In this case the tunnel link will remain in
state LINK_SYNCHING, something leading to unpredictable behavior when
the failover procedure is initiated.
In this commit, we ensure that the node and remaining link goes
back to regular communication state (SELF_UP_PEER_UP/LINK_ESTABLISHED)
when one of the parallel links goes down. We also ensure that we don't
re-enter synch mode if subsequent SYNCH packets arrive on the remaining
link.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the link creation function tipc_link_create() and the way
the link struct it is connected to the node struct. In particular, we
remove the duplicate initialization of some fields which are anyway set
in tipc_link_reset().
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we extract small messages from a message bundle, or
when many messages have accumulated in the link arrival queue, those
messages are added one by one to the lock protected link input queue.
This may increase contention with the reader of that queue, in
the function tipc_sk_rcv().
This commit introduces a temporary, unprotected input queue in
tipc_link_rcv() for such cases. Only when the arrival queue has been
emptied, and the function is ready to return, does it splice the whole
temporary queue into the real input queue.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the most recent changes, all access calls to a link which
may entail addition of messages to the link's input queue are
postpended by an explicit call to tipc_sk_rcv(), using a reference
to the correct queue.
This means that the potentially hazardous implicit delivery, using
tipc_node_unlock() in combination with a binary flag and a cached
queue pointer, now has become redundant.
This commit removes this implicit delivery mechanism both for regular
data messages and for binding table update messages.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to facilitate future improvements to the locking structure, we
want to make resetting and establishing of links non-atomic. I.e., the
functions tipc_node_link_up() and tipc_node_link_down() should be called
from outside the node lock context, and grab/release the node lock
themselves. This requires that we can freeze the link state from the
moment it is set to RESETTING or PEER_RESET in one lock context until
it is set to RESET or ESTABLISHING in a later context. The recently
introduced link FSM makes this possible, so we are now ready to introduce
the above change.
This commit implements this.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have been handling link failover and synchronization
by using an additional link state variable, "exec_mode". This variable
is not independent of the link FSM state, something causing a risk of
inconsistencies, apart from the fact that it clutters the code.
The conditions are now in place to define a new link FSM that covers
all existing use cases, including failover and synchronization, and
eliminate the "exec_mode" field altogether. The FSM must also support
non-atomic resetting of links, which will be introduced later.
The new link FSM is shown below, with 7 states and 8 events.
Only events leading to state change are shown as edges.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | | | |
| | +--------------+ | |
| RESET_EVT| |RESET_EVT |ESTABLISH_EVT |
| | | | |
| | | | |
| V V | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
These changes are fully backwards compatible.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of the link FSM currently takes decisions about and
sends out link protocol messages. This is unnecessary, since such
actions are not the result of any link state change, and are even
decided based on non-FSM state information ("silent_intv_cnt").
We now move the sending of unicast link protocol messages to the
function tipc_link_timeout(), and the initial broadcast synchronization
message to tipc_node_link_up(). The latter is done because a link
instance should not need to know whether it is the first or second
link to a destination. Such information is now restricted to and
handled by the link aggregation layer in node.c
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failover and synchronization have until now been handled by the
links themselves, forcing them to have knowledge about and to access
parallel links in order to make the two algorithms work correctly.
In this commit, we move the control part of this functionality to the
link aggregation level in node.c, which is the right location for this.
As a result, the two algorithms become easier to follow, and the link
implementation becomes simpler.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In many cases the call order when a link is reset goes as follows:
tipc_node_xx()->tipc_link_reset()->tipc_node_link_down()
This is not the right order if we want the node to be in control,
so in this commit we change the order to:
tipc_node_xx()->tipc_node_link_down()->tipc_link_reset()
The fact that tipc_link_reset() now is called from only one
location with a well-defined state will also facilitate later
simplifications of tipc_link_reset() and the link FSM.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In line with our effort to let the node level have full control over
its links, we want to move all link reset calls from link.c to node.c.
Some of the calls can be moved by simply moving the calling function,
when this is the right thing to do. For the remaining calls we use
the now established technique of returning a TIPC_LINK_DOWN_EVT
flag from tipc_link_rcv(), whereafter we perform the reset call when
the call returns.
This change serves as a preparation for the coming commits.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_activate() is redundant, since it mostly performs
settings that have already been done in a preceding tipc_link_reset().
There are three exceptions to this:
- The actual state change to TIPC_LINK_WORKING. This should anyway be done
in the FSM, and not in a separate function.
- Registration of the link with the bearer. This should be done by the
node, since we don't want the link to have any knowledge about its
specific bearer.
- Call to tipc_node_link_up() for user access registration. With the new
role distribution between link aggregation and link level this becomes
the wrong call order; tipc_node_link_up() should instead be called
directly as a result of a TIPC_LINK_UP event, hence by the node itself.
This commit implements those changes.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d999297c3d
("tipc: reduce locking scope during packet reception") we introduced
a new function tipc_build_bcast_sync_msg(), which carries initial
synchronization data between two nodes at first contact and at
re-contact. In this function, we missed to add synchronization data,
with the effect that the broadcast link endpoints will fail to
synchronize correctly at re-contact between a running and a restarted
node. All other cases work as intended.
With this commit, we fix this bug.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit d999297c3d
("tipc: reduce locking scope during packet reception") we introduced
a new function tipc_link_proto_rcv(). This function contains a bug,
so that it sometimes by error sends out a non-zero link priority value
in created protocol messages.
The bug may lead to an extra link reset at initial link establising
with older nodes. This will never happen more than once, whereafter
the link will work as intended.
We fix this bug in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We convert packet/message reception according to the same principle
we have been using for message sending and timeout handling:
We move the function tipc_rcv() to node.c, hence handling the initial
packet reception at the link aggregation level. The function grabs
the node lock, selects the receiving link, and accesses it via a new
call tipc_link_rcv(). This function appends buffers to the input
queue for delivery upwards, but it may also append outgoing packets
to the xmit queue, just as we do during regular message sending. The
latter will happen when buffers are forwarded from the link backlog,
or when retransmission is requested.
Upon return of this function, and after having released the node lock,
tipc_rcv() delivers/tranmsits the contents of those queues, but it may
also perform actions such as link activation or reset, as indicated by
the return flags from the link.
This reduces the number of cpu cycles spent inside the node spinlock,
and reduces contention on that lock.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The logics for determining when a node is permitted to establish
and maintain contact with its peer node becomes non-trivial in the
presence of multiple parallel links that may come and go independently.
A known failure scenario is that one endpoint registers both its links
to the peer lost, cleans up it binding table, and prepares for a table
update once contact is re-establihed, while the other endpoint may
see its links reset and re-established one by one, hence seeing
no need to re-synchronize the binding table. To avoid this, a node
must not allow re-establishing contact until it has confirmation that
even the peer has lost both links.
Currently, the mechanism for handling this consists of setting and
resetting two state flags from different locations in the code. This
solution is hard to understand and maintain. A closer analysis even
reveals that it is not completely safe.
In this commit we do instead introduce an FSM that keeps track of
the conditions for when the node can establish and maintain links.
It has six states and four events, and is strictly based on explicit
knowledge about the own node's and the peer node's contact states.
Only events leading to state change are shown as edges in the figure
below.
+--------------+
| SELF_UP/ |
+---------------->| PEER_COMING |-----------------+
SELF_ | +--------------+ |PEER_
ESTBL_ | | |ESTBL_
CONTACT| SELF_LOST_CONTACT | |CONTACT
| v |
| +--------------+ |
| PEER_ | SELF_DOWN/ | SELF_ |
| LOST_ +--| PEER_LEAVING |<--+ LOST_ v
+-------------+ CONTACT | +--------------+ | CONTACT +-----------+
| SELF_DOWN/ |<----------+ +----------| SELF_UP/ |
| PEER_DOWN |<----------+ +----------| PEER_UP |
+-------------+ SELF_ | +--------------+ | PEER_ +-----------+
| LOST_ +--| SELF_LEAVING/|<--+ LOST_ A
| CONTACT | PEER_DOWN | CONTACT |
| +--------------+ |
| A |
PEER_ | PEER_LOST_CONTACT | |SELF_
ESTBL_ | | |ESTBL_
CONTACT| +--------------+ |CONTACT
+---------------->| PEER_UP/ |-----------------+
| SELF_COMING |
+--------------+
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In our effort to move control of the links to the link aggregation
layer, we move the perodic link supervision timer to struct tipc_node.
The new timer is shared between all links belonging to the node, thus
saving resources, while still kicking the FSM on both its pertaining
links at each expiration.
The current link timer and corresponding functions are removed.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a second, simpler, link timer function, tipc_link_timeout().
The new function makes use of the new FSM function introduced in the
previous commit, and just like it, takes a buffer queue as parameter.
It returns an event bit field and potentially a link protocol packet
to the caller.
The existing timer function, link_timeout(), is still needed for a
while, so we redesign it to become a wrapper around the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link FSM implementation is currently unnecessarily complex.
It sometimes checks for conditional state outside the FSM data
before deciding next state, and often performs actions directly
inside the FSM logics.
In this commit, we create a second, simpler FSM implementation,
that as far as possible acts only on states and events that it is
strictly defined for, and postpone any actions until it is finished
with its decisions. It also returns an event flag field and an a
buffer queue which may potentially contain a protocol message to
be sent by the caller.
Unfortunately, we cannot yet make the FSM "clean", in the sense
that its decisions are only based on FSM state and event, and that
state changes happen only here. That will have to wait until the
activate/reset logics has been cleaned up in a future commit.
We also rename the link states as follows:
WORKING_WORKING -> TIPC_LINK_WORKING
WORKING_UNKNOWN -> TIPC_LINK_PROBING
RESET_UNKNOWN -> TIPC_LINK_RESETTING
RESET_RESET -> TIPC_LINK_ESTABLISHING
The existing FSM function, link_state_event(), is still needed for
a while, so we redesign it to make use of the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation for later changes, we introduce a new function
tipc_link_build_proto_msg(). Instead of actually sending the created
protocol message, it only creates it and adds it to the head of a
skb queue provided by the caller.
Since we still need the existing function tipc_link_protocol_xmit()
for a while, we redesign it to make use of the new function.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The status flag LINK_STOPPED is not needed any more, since the
mechanism for delayed deletion of links has been removed.
Likewise, LINK_STARTED and LINK_START_EVT are unnecessary,
because we can just as well start the link timer directly from
inside tipc_link_create().
We eliminate these flags in this commit.
Instead of the above flags, we now introduce three new link modes,
TIPC_LINK_OPEN, TIPC_LINK_BLOCKED and TIPC_LINK_TUNNEL. The values
indicate whether, and in the case of TIPC_LINK_TUNNEL, which, messages
the link is allowed to receive in this state. TIPC_LINK_BLOCKED also
blocks timer-driven protocol messages to be sent out, and any change
to the link FSM. Since the modes are mutually exclusive, we convert
them to state values, and rename the 'flags' field in struct tipc_link
to 'exec_mode'.
Finally, we move the #defines for link FSM states and events from link.h
into enums inside the file link.c, which is the real usage scope of
these definitions.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, message sending is performed through a deep call chain,
where the node spinlock is grabbed and held during a significant
part of the transmission time. This is clearly detrimental to
overall throughput performance; it would be better if we could send
the message after the spinlock has been released.
In this commit, we do instead let the call revert on the stack after
the buffer chain has been added to the transmission queue, whereafter
clones of the buffers are transmitted to the device layer outside the
spinlock scope.
As a further step in our effort to separate the roles of the node
and link entities we also move the function tipc_link_xmit() to
node.c, and rename it to tipc_node_xmit().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the function tipc_link_xmit() is given a buffer list for
transmission, it currently consumes the list both when transmission
is successful and when it fails, except for the special case when
it encounters link congestion.
This behavior is inconsistent, and needs to be corrected if we want
to avoid problems in later commits in this series.
In this commit, we change this to let the function consume the list
only when transmission is successful, and leave the list with the
sender in all other cases. We also modifiy the socket code so that
it adapts to this change, i.e., purges the list when a non-congestion
error code is returned.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, the link input queue and the name distributor receive
queues are fields aggregated in struct tipc_link. This is a hazard,
because a link might be deleted while a receiving socket still keeps
reference to one of the queues.
This commit fixes this bug. However, rather than adding yet another
reference counter to the critical data path, we move the two queues
to safe ground inside struct tipc_node, which is already protected, and
let the link code only handle references to the queues. This is also
in line with planned later changes in this area.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct 'tipc_node' currently contains two arrays for link attributes,
one for the link pointers, and one for the usable link MTUs.
We now group those into a new struct 'tipc_link_entry', and intoduce
one single array consisting of such enties. Apart from being a cosmetic
improvement, this is a starting point for the strict master-slave
relation between node and link that we will introduce in the following
commits.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1f66d161ab
("tipc: introduce starvation free send algorithm")
we introduced a counter per priority level for buffers
in the link backlog queue. We also introduced a new
function tipc_link_purge_backlog(), to reset these
counters to zero when the link is reset.
Unfortunately, we missed to call this function when
the broadcast link is reset, with the result that the
values of these counters might be permanently skewed
when new nodes are attached. This may in the worst case
lead to permananent, but spurious, broadcast link
congestion, where no broadcast packets can be sent at
all.
We fix this bug with this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit dd3f9e70f5
("tipc: add packet sequence number at instant of transmission") we
made a change with the consequence that packets in the link backlog
queue don't contain valid sequence numbers.
However, when we create a link protocol message, we still use the
sequence number of the first packet in the backlog, if there is any,
as "next_sent" indicator in the message. This may entail unnecessary
retransissions or stale packet transmission when there is very low
traffic on the link.
This commit fixes this issue by only using the current value of
tipc_link::snd_nxt as indicator.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the packet sequence number is updated and added to each
packet at the moment a packet is added to the link backlog queue.
This is wasteful, since it forces the code to traverse the send
packet list packet by packet when adding them to the backlog queue.
It would be better to just splice the whole packet list into the
backlog queue when that is the right action to do.
In this commit, we do this change. Also, since the sequence numbers
cannot now be assigned to the packets at the moment they are added
the backlog queue, we do instead calculate and add them at the moment
of transmission, when the backlog queue has to be traversed anyway.
We do this in the function tipc_link_push_packet().
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link congestion algorithm used until now implies two problems.
- It is too generous towards lower-level messages in situations of high
load by giving "absolute" bandwidth guarantees to the different
priority levels. LOW traffic is guaranteed 10%, MEDIUM is guaranted
20%, HIGH is guaranteed 30%, and CRITICAL is guaranteed 40% of the
available bandwidth. But, in the absence of higher level traffic, the
ratio between two distinct levels becomes unreasonable. E.g. if there
is only LOW and MEDIUM traffic on a system, the former is guaranteed
1/3 of the bandwidth, and the latter 2/3. This again means that if
there is e.g. one LOW user and 10 MEDIUM users, the former will have
33.3% of the bandwidth, and the others will have to compete for the
remainder, i.e. each will end up with 6.7% of the capacity.
- Packets of type MSG_BUNDLER are created at SYSTEM importance level,
but only after the packets bundled into it have passed the congestion
test for their own respective levels. Since bundled packets don't
result in incrementing the level counter for their own importance,
only occasionally for the SYSTEM level counter, they do in practice
obtain SYSTEM level importance. Hence, the current implementation
provides a gap in the congestion algorithm that in the worst case
may lead to a link reset.
We now refine the congestion algorithm as follows:
- A message is accepted to the link backlog only if its own level
counter, and all superior level counters, permit it.
- The importance of a created bundle packet is set according to its
contents. A bundle packet created from messges at levels LOW to
CRITICAL is given importance level CRITICAL, while a bundle created
from a SYSTEM level message is given importance SYSTEM. In the latter
case only subsequent SYSTEM level messages are allowed to be bundled
into it.
This solves the first problem described above, by making the bandwidth
guarantee relative to the total number of users at all levels; only
the upper limit for each level remains absolute. In the example
described above, the single LOW user would use 1/11th of the bandwidth,
the same as each of the ten MEDIUM users, but he still has the same
guarantee against starvation as the latter ones.
The fix also solves the second problem. If the CRITICAL level is filled
up by bundle packets of that level, no lower level packets will be
accepted any more.
Suggested-by: Gergely Kiss <gergely.kiss@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We change the sequence number checkpointing that is performed
by the timer in order to discover if the peer is active. Currently,
we store a checkpoint of the next expected sequence number "rcv_nxt"
at each timer expiration, and compare it to the current expected
number at next timeout expiration. Instead, we now use the already
existing field "silent_intv_cnt" for this task. We step the counter
at each timeout expiration, and zero it at each valid received packet.
If no valid packet has been received from the peer after "abort_limit"
number of silent timer intervals, the link is declared faulty and reset.
We also remove the multiple instances of timer activation from inside
the FSM function "link_state_event()", and now do it at only one place;
at the end of the timer function itself.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We rename some fields in struct tipc_link, in order to give them more
descriptive names:
next_in_no -> rcv_nxt
next_out_no-> snd_nxt
fsm_msg_cnt-> silent_intv_cnt
cont_intv -> keepalive_intv
last_retransmitted -> last_retransm
There are no functional changes in this commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the sequence number in the TIPC protocol is 16 bits, we have
until now stored it internally as an unsigned 32 bits integer.
We got around this by always doing explicit modulo-65535 operations
whenever we need to access a sequence number.
We now make the incoming and outgoing sequence numbers to unsigned
16-bit integers, and remove the modulo operations where applicable.
We also move the arithmetic inline functions for 16 bit integers
to core.h, and the function buf_seqno() to msg.h, so they can easily
be accessed from anywhere in the code.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this commit, the link timer has been running at a "continuity
interval" of configured link tolerance/4. When a timer wakes up and
discovers that there has been no sign of life from the peer during the
previous interval, it divides its own timer interval by another factor
four, and starts sending one probe per new interval. When the configured
link tolerance time has passed without answer, i.e. after 16 unacked
probes, the link is declared faulty and reset.
This is unnecessary complex. It is sufficient to continue with the
original continuity interval, and instead reset the link after four
missed probe responses. This makes the timer handling in the link
simpler, and opens up for some planned later changes in this area.
This commit implements this change.
Reviewed-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 4b475e3f2f8e4e241de101c8240f1d74d0470494
("tipc: eliminate delayed link deletion at link failover") the extra
boolean parameter "shutting_down" is not any longer needed for the
functions bearer_disable() and tipc_link_delete_list().
Furhermore, the function tipc_link_reset_links(), called from
bearer_reset() is now unnecessary. We can just as well delete
all the links, as we do in bearer_disable(), and start over with
creating new links.
This commit introduces those changes.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to get or set the broadcast link window through the
new netlink API. The functionality was unintentionally missing from
the new netlink API. Adding this means that we also fix the breakage
in the old API when coming through the compat layer.
Fixes: 37e2d4843f (tipc: convert legacy nl link prop set to nl compat)
Reported-by: Tomi Ollila <tomi.ollila@iki.fi>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we try to accumulate arrived packets in the links's
'deferred' queue during the parallel link syncronization phase.
This entails two problems:
- With an unlucky combination of arriving packets the algorithm
may go into a lockstep with the out-of-sequence handling function,
where the synch mechanism is adding a packet to the deferred queue,
while the out-of-sequence handling is retrieving it again, thus
ending up in a loop inside the node_lock scope.
- Even if this is avoided, the link will very often send out
unnecessary protocol messages, in the worst case leading to
redundant retransmissions.
We fix this by just dropping arriving packets on the upcoming link
during the synchronization phase, thus relying on the retransmission
protocol to resolve the situation once the two links have arrived to
a synchronized state.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 35b9dd7607 ("tipc: add bearer get/dump to new netlink api")
Fixes: 7be57fc691 ("tipc: add link get/dump to new netlink api")
Fixes: 46f15c6794 ("tipc: add media get/dump to new netlink api")
CC: Richard Alpe <richard.alpe@ericsson.com>
CC: Jon Maloy <jon.maloy@ericsson.com>
CC: Ying Xue <ying.xue@windriver.com>
CC: tipc-discussion@lists.sourceforge.net
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link statistics is dumped over netlink, we iterate over
the list of peer nodes and append each links statistics to
the netlink msg. In the case where the dump is resumed after
filling up a nlmsg, the node refcnt is decremented without
having been incremented previously which may cause the node
reference to be freed. When this happens, the following
info/stacktrace will be generated, followed by a crash or
undefined behavior.
We fix this by removing the erroneous call to tipc_node_put
inside the loop that iterates over nodes.
[ 384.312303] INFO: trying to register non-static key.
[ 384.313110] the code is fine but needs lockdep annotation.
[ 384.313290] turning off the locking correctness validator.
[ 384.313290] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.0.0+ #13
[ 384.313290] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 384.313290] ffff88003c6d0290 ffff88003cc03ca8 ffffffff8170adf1 0000000000000007
[ 384.313290] ffffffff82728730 ffff88003cc03d38 ffffffff810a6a6d 00000000001d7200
[ 384.313290] ffff88003c6d0ab0 ffff88003cc03ce8 0000000000000285 0000000000000001
[ 384.313290] Call Trace:
[ 384.313290] <IRQ> [<ffffffff8170adf1>] dump_stack+0x4c/0x65
[ 384.313290] [<ffffffff810a6a6d>] __lock_acquire+0xf3d/0xf50
[ 384.313290] [<ffffffff810a7375>] lock_acquire+0xd5/0x290
[ 384.313290] [<ffffffffa0043e8c>] ? link_timeout+0x1c/0x170 [tipc]
[ 384.313290] [<ffffffffa0043e70>] ? link_state_event+0x4e0/0x4e0 [tipc]
[ 384.313290] [<ffffffff81712890>] _raw_spin_lock_bh+0x40/0x80
[ 384.313290] [<ffffffffa0043e8c>] ? link_timeout+0x1c/0x170 [tipc]
[ 384.313290] [<ffffffffa0043e8c>] link_timeout+0x1c/0x170 [tipc]
[ 384.313290] [<ffffffff810c4698>] call_timer_fn+0xb8/0x490
[ 384.313290] [<ffffffff810c45e0>] ? process_timeout+0x10/0x10
[ 384.313290] [<ffffffff810c5a2c>] run_timer_softirq+0x21c/0x420
[ 384.313290] [<ffffffffa0043e70>] ? link_state_event+0x4e0/0x4e0 [tipc]
[ 384.313290] [<ffffffff8105a954>] __do_softirq+0xf4/0x630
[ 384.313290] [<ffffffff8105afdd>] irq_exit+0x5d/0x60
[ 384.313290] [<ffffffff8103ade1>] smp_apic_timer_interrupt+0x41/0x50
[ 384.313290] [<ffffffff817144a0>] apic_timer_interrupt+0x70/0x80
[ 384.313290] <EOI> [<ffffffff8100db10>] ? default_idle+0x20/0x210
[ 384.313290] [<ffffffff8100db0e>] ? default_idle+0x1e/0x210
[ 384.313290] [<ffffffff8100e61a>] arch_cpu_idle+0xa/0x10
[ 384.313290] [<ffffffff81099803>] cpu_startup_entry+0x2c3/0x530
[ 384.313290] [<ffffffff810d2893>] ? clockevents_register_device+0x113/0x200
[ 384.313290] [<ffffffff81038b0f>] start_secondary+0x13f/0x170
Fixes: 8a0f6ebe84 ("tipc: involve reference counter for node structure")
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a link is being established, the two endpoints advertise their
respective interface MTU in the transmitted RESET and ACTIVATE messages.
If there is any difference, the lower of the two MTUs will be selected
for use by both endpoints.
However, as a remnant of earlier attempts to introduce TIPC level
routing. there also exists an MTU discovery mechanism. If an intermediate
node has a lower MTU than the two endpoints, they will discover this
through a bisectional approach, and finally adopt this MTU for common use.
Since there is no TIPC level routing, and probably never will be,
this mechanism doesn't make any sense, and only serves to make the
link level protocol unecessarily complex.
In this commit, we eliminate the MTU discovery algorithm,and fall back
to the simple MTU advertising approach. This change is fully backwards
compatible.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled manually, all its links have to be reset
and deleted. However, if there is a remaining, parallel link ready
to take over a deleted link's traffic, we currently delay the delete
of the removed link until the failover procedure is finished. This
is because the remaining link needs to access state from the reset
link, such as the last received packet number, and any partially
reassembled buffer, in order to perform a successful failover.
In this commit, we do instead move the state data over to the new
link, so that it can fulfill the procedure autonomously, without
accessing any data on the old link. This means that we can now
proceed and delete all pertaining links immediately when a bearer
is disabled. This saves us from some unnecessary complexity in such
situations.
We also choose to change the confusing definitions CHANGEOVER_PROTOCOL,
ORIGINAL_MSG and DUPLICATE_MSG to the more descriptive TUNNEL_PROTOCOL,
FAILOVER_MSG and SYNCH_MSG respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8b4ed8634f
("tipc: eliminate race condition at dual link establishment")
we introduced a parallel link synchronization mechanism that
guarentees sequential delivery even for users switching from
an old to a newly established link. The new mechanism makes it
unnecessary to deliver the tunneled duplicate packets back to
the old link, as we are currently doing. It is now sufficient
to use the last tunneled packet's inner sequence number as
synchronization point between the two parallel links, whereafter
it can be dropped.
In this commit, we drop the duplicate packets arriving on the new
link, after updating the synchronization point at each new arrival.
Although it would now have been sufficient for the other endpoint
to only tunnel the last packet in its send queue, and not the
entire queue, we must still do this to maintain compatibility
with older nodes.
This commit makes it possible to get rid if some complex
interaction between the two parallel links.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TIPC node hash node table is protected with rcu lock on read side.
tipc_node_find() is used to look for a node object with node address
through iterating the hash node table. As the entire process of what
tipc_node_find() traverses the table is guarded with rcu read lock,
it's safe for us. However, when callers use the node object returned
by tipc_node_find(), there is no rcu read lock applied. Therefore,
this is absolutely unsafe for callers of tipc_node_find().
Now we introduce a reference counter for node structure. Before
tipc_node_find() returns node object to its caller, it first increases
the reference counter. Accordingly, after its caller used it up,
it decreases the counter again. This can prevent a node being used by
one thread from being freed by another thread.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Despite recent improvements, the establishment of dual parallel
links still has a small glitch where messages can bypass each
other. When the second link in a dual-link configuration is
established, part of the first link's traffic will be steered over
to the new link. Although we do have a mechanism to ensure that
packets sent before and after the establishment of the new link
arrive in sequence to the destination node, this is not enough.
The arriving messages will still be delivered upwards in different
threads, something entailing a risk of message disordering during
the transition phase.
To fix this, we introduce a synchronization mechanism between the
two parallel links, so that traffic arriving on the new link cannot
be added to its input queue until we are guaranteed that all
pre-establishment messages have been delivered on the old, parallel
link.
This problem seems to always have been around, but its occurrence is
so rare that it has not been noticed until recent intensive testing.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent changes in message importance handling it becomes
possible to simplify handling of messages and sockets when we
encounter link congestion.
We merge the function tipc_link_cong() into link_schedule_user(),
and simplify the code of the latter. The code should now be
easier to follow, especially regarding return codes and handling
of the message that caused the situation.
In case the scheduling function is unable to pre-allocate a wakeup
message buffer, it now returns -ENOBUFS, which is a more correct
code than the previously used -EHOSTUNREACH.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only use a single counter; the length of the backlog
queue, to determine whether a message should be accepted to the queue
or not. Each time a message is being sent, the queue length is compared
to a threshold value for the message's importance priority. If the queue
length is beyond this threshold, the message is rejected. This algorithm
implies a risk of starvation of low importance senders during very high
load, because it may take a long time before the backlog queue has
decreased enough to accept a lower level message.
We now eliminate this risk by introducing a counter for each importance
priority. When a message is sent, we check only the queue level for that
particular message's priority. If that is ok, the message can be added
to the backlog, irrespective of the queue level for other priorities.
This way, each level is guaranteed a certain portion of the total
bandwidth, and any risk of starvation is eliminated.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1186adf7df ("tipc: simplify message forwarding and
rejection in socket layer") -EHOSTUNREACH is propagated back to
the sending process if we fail to deliver the message to another
socket local to the node.
This is wrong, host unreachable should only be reported when the
destination port/name does not exist in the cluster, and that
check is always done before sending the message. Also, this
introduces inconsistent sendmsg() behavior for local/remote
destinations. Errors occurring on the receiving side should not
trickle up to the sender. If message delivery fails TIPC should
either discard the packet or reject it back to the sender based
on the destination droppable option.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Messages transferred by TIPC are assigned an "importance priority", -an
integer value indicating how to treat the message when there is link or
destination socket congestion.
There is no separate header field for this value. Instead, the message
user values have been chosen in ascending order according to perceived
importance, so that the message user field can be used for this.
This is not a good solution. First, we have many more users than the
needed priority levels, so we end up with treating more priority
levels than necessary. Second, the user field cannot always
accurately reflect the priority of the message. E.g., a message
fragment packet should really have the priority of the enveloped
user data message, and not the priority of the MSG_FRAGMENTER user.
Until now, we have been working around this problem in different ways,
but it is now time to implement a consistent way of handling such
priorities, although still within the constraint that we cannot
allocate any more bits in the regular data message header for this.
In this commit, we define a new priority level, TIPC_SYSTEM_IMPORTANCE,
that will be the only one used apart from the four (lower) user data
levels. All non-data messages map down to this priority. Furthermore,
we take some free bits from the MSG_FRAGMENTER header and allocate
them to store the priority of the enveloped message. We then adjust
the functions msg_importance()/msg_set_importance() so that they
read/set the correct header fields depending on user type.
This small protocol change is fully compatible, because the code at
the receiving end of a link currently reads the importance level
only from user data messages, where there is no change.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct tipc_link contains one single queue for outgoing packets,
where both transmitted and waiting packets are queued.
This infrastructure is hard to maintain, because we need
to keep a number of fields to keep track of which packets are
sent or unsent, and the number of packets in each category.
A lot of code becomes simpler if we split this queue into a transmission
queue, where sent/unacknowledged packets are kept, and a backlog queue,
where we keep the not yet sent packets.
In this commit we do this separation.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unicast packet header contains a broadcast acknowledge sequence
number, that may need to be conveyed to the broadcast link for proper
treatment. Currently, the function tipc_rcv(), which is on the most
critical data path, calls the function tipc_bclink_acknowledge() to
have this done. This call is made for each received packet, and results
in the unconditional grabbing of the broadcast link spinlock.
This is unnecessary, since we can see directly from tipc_rcv() if
the acknowledged number differs from what has been previously acked
from the node in question. In the vast majority of cases the numbers
won't differ, and there is nothing to update.
We now make the call to tipc_bclink_acknowledge() conditional
to that the two ack values differ.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
