Current FSI-Ak4642 device had niche settings which were
FSI2-A-AK4643 and FSI-A-AK4642.
This patch add platform_device_id which can control
FSI/FSI2, PortA/PortB, AK4642/AK4643 from platform data.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch permuted clock arrays in the order of MSTP
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Have to add DMA slave configuration to enable DMA for the sh7372 MMCIF
controller.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add DMA slave IDs and slave definitions for MMCIF on sh7372.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The PLLC2 clock was utilizing the same sort of enable/disable without
regard to usecount approach that the FSIDIV clock was when being used as
a PLL pass-through. This forces the enable/disable through the clock
framework, which now prevents the clock from being ripped out or modified
underneath users that have an existing handle on it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI didn't use set_rate for ak4642,
and used dummy rate when init.
And FSI driver was modified to always call set_rate.
The user which are using FSI set_rate is only AP4 now.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current AP4 FSI set_rate function used bogus clock process
which didn't care enable/disable and clk->usecound.
To solve this issue, this patch also modify FSI driver to call
set_rate with enough options.
This patch modify it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current FSIDIV clock framework had bogus disable.
This patch remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Just add port multiplex settings to enable i2c modules.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consists of platform device resources/data for the board, and
simple clvdev entry for MSTP bit for keysc module.
This support only 49 of 80 key-switches on the board.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the AP4EVB board code to go from a single I/O
resource to two I/O resources for the MIPI-DSI driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Ag5evm board now uses gpio api to initialize pins and peripherals.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
PFC definitions for sh73a0 to support GPIO and pinmux handling.
Signed-off-by: Takashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the entry macros are all globbed together, this simply splits
them out in to their insular variants. Future work such as the GIC
generalization will replace some of these and tidy the abstraction up
further.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds initial support for Renesas SH-Mobile AG5.
At this point the AG5 CPU support is limited to the ARM
core, SCIF serial and a CMT timer together with L2 cache
and the GIC. The AG5EVM board also supports Ethernet.
Future patches will add support for GPIO, INTCS, CPGA
and platform data / driver updates for devices such as
IIC, LCDC, FSI, KEYSC, CEU and SDHI among others.
The code in entry-macro.S will be cleaned up when the
ARM IRQ demux code improvements have been merged.
Depends on the AG5EVM mach-type recently registered but
not yet present in arch/arm/tools/mach-types.
As the AG5EVM board comes with 512MiB memory it is
recommended to turn on HIGHMEM.
Many thanks to Yoshii-san for initial bring up.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix a MSTP assignment problem in the sh7372 clock
framework code. The USB drivers should attach to
MSTP322 not MSTP33 where IIC1 is located.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently each one of the CPUs manually selects the same feature set, and
there's a reasonable expectation that none of these will change for
future CPUs in the SH-Mobile / R-Mobile family, so we move those over to
the top-level ARCH_SHMOBILE.
While we're at it, all of the CPUs support optional GPIOs via the PFC,
do not have I/O ports, and expect sparse IRQ, so we bring the
configuration in line across the board.
This more or less brings the ARM-based parts in sync with their SH
counterparts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that clk_set_rate_ex() is gone, there is also no way to get at rate
setting algo id, which is now also completely unused. Kill it off before
new clock ops start using it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On ap4evb PLLC2 is only used as a parent of the HDMI clock, therefore it can
be reconfigured freely to improve HDMI clock precision.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes the loader and bootenv partitions read-only under MTD for the
on-board NOR flash.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As non-PFC chips are added that may support IRQs, pass through to the
generic helper. This follows the the SH change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The updated sh clock framework has introduced a .nr_freqs element of struct
clk, which has to be initialised with the number of possible frequencies.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many of the config bit are presently duplicated between the platforms,
which will gradually cleaned up through centralization. For the moment we
expose some new INTC features through drivers/sh/Kconfig that the ARM
platforms presently don't enable, so make it generally available.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
On AP4EVB the card detect pin of the top SD/MMC slot is not directly
connected to the tmio/mmcif controller but to a GPIO pin, so polling
needs to be done for SDHI1 and MMCIF in order to support hotplug for
that slot. SHDI1 and MMCIF share that slot, and the used controller
is selected by a DIP switch.
This patch adds a helper function to check if a card is present in that
particular slot, registers this function with SDHI1 and MMCIF and enables
polling for SDHI1.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add platform data, necessary to use Sony IMX074 camera sensor with AP4EVB.
Note: this does not work reliably without an API to reserve contiguous and
coherent memory for V4L DMA buffers. Such memory reservation has to be added as
soon as a suitable API becomes available.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
This patch adds support for the two first channels of
the TMU0 timer block on sh7372. One channel is used
for clock event, the other for clock source.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that HDMI videomodes have become optional, they can be safely removed from
ap4evb platform data, since anyway 720p seems to be the best supported mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch also registered global extal clocks to sh7372.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move SH-Mobile ARM systems over from the legacy
"clk" member of struct sh_timer_config to using
the device name and clkdev for clock matching.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces sh7372_late_devices which
should include all regular processor specific
platform devices.
Early platform devices for console and timers
should be put on the sh7372_early_devices list,
all other devices should be on sh7372_late_devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current touchpanel had below 2 issues
- LCDD2 pin which is needed for WVGA was changed to
IRQ28_123 pin on ts_get_pendown_state
- GPIO pull up on ts_init was disabled by gpio_request
on ts_get_pendown_state.
This mean the return value from gpio_get_value is untrusted.
This patch solve these issues
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add video modes for 480p and SXGA (1280x1024).
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is a preparation for HDMI hotplug support. This patch just moves all
platform defined video modes for the sh_mobile_lcdcfb driver to separate
arrays and switches all users to use element 0 of that array, so, this patch
doesn't introduce any functional changes and as such should not cause any
regressions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add ignored device name by comment-out in INTCS.
And MSIOF which has been forgotten is added
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use evt2irq() for DMAC resources on sh7372.
This makes the code easier to read and also
allows adjusting the INTC base offset without
breaking platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend dip switch comments for QHD and WVGA LCD panels
on AP4EVB. Similar to the Ecovec comments.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modify x_plate_ohms to correct value for tsc2007,
and removed un-necessary ts_get_pendown_state().
gpio_pull_up() was removed also.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SDHI1 on AP4EVB has no pin to detect write protection of a card.
This had the result that a card inserted in this slot was always detected
as read only. This patch adds the corresponding flag to disable
write protection detection for SDHI1.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
AP4EVB has to reparent PLLC2 to provide a precise HDMI clock, this is only
possible, if PLLC2 hasn't been enabled yet. Since no other driver currently
uses PLLC2 we can safely remove the CLK_ENABLE_ON_INIT flag. This fixes
the "Cannot set PLLC2 parent: -16, 1 users" error message, when trying to
use HDMI on AP4EVB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows control of the leds on the AP4EVB board by kernel events (triggers)
like mmc0/mmc1. In userland, the leds won't be available anymore over
/sys/class/gpio but via /sys/class/leds.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Two more clocks to be managed by the runtime PM.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the SH-Mobile ARM Runtime PM implementation V3.
Only clocks are managed at this point. If Runtime PM
is disabled then the clocks will be enabled before
->probe() and disabled after ->remove().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Support HDMI in 720p mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add definitions for DV_CLKI and HDMI clocks, extend support for PLLC2 and some
other clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This function is necessary to ensure the detection of pen-down.
This patch support both QHD / WVGA pannel.
Tested-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
EXTAL1 is clocked at 26.0MHz
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With these defines now it is possible to use
gpio_request(GPIO_FN_LCDC1_SELECT, NULL) or ...LCDC0... respectively to
switch between the two LCDC instances.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On AP4EVB board, it is possible to select LCD panel type
which are parallel or MIPI by SW3, SW43 dip-switch.
This patch add parallel LCD settings and
select menu to Kconfig.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce SHMOBILE_TIMER_HZ for SH-Mobile.
Allow users to select HZ on their system to
minimize potential timer drift. Use 128 Hz as
default to work well with the 32768 Hz RCLK.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NR_IRQS_LEGACY is now defined in asm/irq.h,
so drop it in mach/irqs.h.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MMC0/SDHI1 (CN7) can be selected by dip switch.
And card voltage can be selected by jumper pin.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the irq numbers for MMCIF
to make use of evt2irq().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The FSI changes introduced IS_ERR_VALUE() checks for error conditions,
despite clk_get() handing back a pointer. Switch these over to IS_ERR()
like the rest of the code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7372 can use DMA with the SCI serial driver. Add required slave IDs and slave
descriptors.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ap4evb board is equipped with two card slots: one SD-card slot and one
SD-/MMC-card slot. The latter is connected to the second SDHI interface on
sh7372 (SDHI1). Its power supply can be jumpered either to 1.8 or 3.3V, we fix
it at default 1.8V for now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds DMA support for the sh7372 sh-mobile ARM core, using the shdma
dmaengine driver, and uses DMA for the SDHI SD-card controller on this SoC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current SH7372 setup code registers 7 SCIF ports, which is wrong.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ap4evb uses an LCD, connected to the SoC over the MIPI bus. This patch adds
platform data to configure this display and a static clock activation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Define clock objects for switching on and off clocks for LCDC0, LCDC1 and MIPI
DSI-Tx.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of clock framework tables/code for sh7377.
MSTP support is included for the following hardware blocks:
KEYSC, SCIF, IIC, IRDA, FLCTL, USB, SDHI and UIO.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of clock framework tables/code for sh7367.
MSTP support is included for the following hardware blocks:
KEYSC, SCIF, IIC, IRDA, FLCTL, VOU, SIU, USB, SDHI and UIO.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixes for the sh7372 clock framework:
- remove unused #include <linux/platform_device.h>
- add sh7372 prefix to user modifiable root clocks
- put modifiable root clock prototypes in header file
- fix off-by-one id error on VEU MSTP clocks
- make arrays static
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the irq numbers on sh7372/AP4EVB
to make use of evt2irq() and intcs_evt2irq().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the irq numbers on sh7377/G4EVM
to make use of evt2irq() and intcs_evt2irq().
Makes the system cope with an updated INTCS_VECT_BASE.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the irq numbers on sh7367/G3EVM
to make use of evt2irq() and intcs_evt2irq().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch sets CONSISTENT_DMA_SIZE to 158 MB
for all SH-Mobile ARM processors.
The DMA area is mapped at 0xf6000000 - 0xffdfffff,
on top of the 256 MB I/O window at 0xe6000000.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is V2 of clock framework tables/code for sh7372.
MSTP are included for KEYSC, SCIF, IIC, USB, SDHI and UIO.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Teach SH-Mobile ARM how to make use of the shared SH clock
framework. This commit is one atomic switch that dumps the
local hackery and instead links in the shared clock framework
code in drivers/sh. A few local functions are kept in clock.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the sh7372 INTCS interrupt controller.
INTCS is the interrupt controller for the sh7372 SuperH
processor core. It is tied into the INTCA interrupt
controller which interfaces to the ARM processor.
INTCS support is implemented using a new INTC table
together with a chained interrupt handler that ties
into the already supported INTCA controller.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Change INTCS_VECT_BASE from 0x3400 to 0x2200.
The old value 0x3400 gave the INTCA and INTCS interrupt
conrollers separated spaces, but required ARM support
for more than 512 NR_IRQS which is not in place at this
point.
The value 0x2200 will make some of the INTCA interrupts
make use of empty INTCS areas. This is a bit more error
prone but works fine as a workaround for G3, G3 and AP4.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add SDHI support for G4 board.
Current gpio frame work doesn't have
the method to control only pull-up/down/free.
So, it have special gpio_pull_up function for SDHI.
It is quick hack, so this function should be replaced
by correct gpio frame work in future.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the sh7377 INTCS interrupt controller.
INTCS is the interrupt controller for the sh7377 SuperH
processor core. It is tied into the INTCA interrupt
controller which interfaces to the ARM processor.
INTCS support is implemented using a new INTC table
together with a chained interrupt handler that ties
into the already supported INTCA controller.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the sh7367 INTCS interrupt controller.
INTCS is the interrupt controller for the sh7367 SuperH
processor core. It is tied into the INTCA interrupt
controller which interfaces to the ARM processor.
INTCS support is implemented using a new INTC table
together with a chained interrupt handler that ties
into the already supported INTCA controller.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SH-Mobile ARM INTCS macros for the INTCS controller.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh7372 chip has 2 INTC.
Then, I2C0 is connected to INTCS, and I2C1 is connected to INTCA.
Both of these has no GPIO settings.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors for sh7372 using the recently
merged INTC force_enable/disable feature.
With this in place SDHI hotplug is supported using
the drivers sh_mobile_sdhi and tmio_mmc.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors for sh7377 using the recently
merged INTC force_enable/disable feature.
With this in place SDHI hotplug is supported using
the drivers sh_mobile_sdhi and tmio_mmc.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Merge the SDHI vectors for sh7367 using the recently
merged INTC force_enable/disable feature.
With this in place SDHI hotplug is supported using
the drivers sh_mobile_sdhi and tmio_mmc.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds KEYSC platform data for the G4EVM board.
Signed-off-by: NISHIMOTO Hiroki <nishimoto.hiroki@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds FLCTL platform data for the G3EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds KEYSC platform data for the G3EVM board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Because AP4 board has capacitor for KEYSC,
we need much time for waiting.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add G4EVM platform data and a magic setup sequence to
initialize the r8a66597 block aka USBHS in sh7377.
Signed-off-by: NISHIMOTO Hiroki <nishimoto.hiroki@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
