Detected symbol rate value was returned too small.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Inversion ON was reported as inversion OFF and vice versa.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
FEC AUTO is valid for PSK-8 modulation too. Add it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only supported modulation for DVB-S is QPSK. Modulation parameter
contains invalid value for DVB-S on some cases, which leads driver
refusing tuning attempt. Due to that, hard code modulation to QPSK
in case of DVB-S.
Cc: stable@vger.kernel.org
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
First 8 bytes belonging to firmware image were hard-coded and uploaded
by the driver mistakenly. Introduce new corrected firmware file and
remove those 8 bytes from the driver.
New firmware image could be extracted from the PCTV 292e driver CD
using following command:
$ dd if=/TVC 6.4.8/Driver/PCTV Empia/emOEM.sys ibs=1 skip=1089408 count=2728 of=dvb-demod-si2168-02.fw
$ md5sum dvb-demod-si2168-02.fw
d8da7ff67cd56cd8aa4e101aea45e052 dvb-demod-si2168-02.fw
$ sudo cp dvb-demod-si2168-02.fw /lib/firmware/
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix following warnings:
si2168_cmd_execute() warn: add some parenthesis here?
si2168_cmd_execute() warn: maybe use && instead of &
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bit3 was not cleared always leaving driver reporting demod is not
fully locked. Do not check bit0 as it seems to be always 0.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add sleep ops to lgdt3304_ops to invoke lgdt3305_sleep() to be called
from dvb_frontend_suspend(). lgdt3305_soft_reset() is called for both
3304 and 3305 devices. soft_reset and sleep touch LGDT3305_GEN_CTRL_3
on 3304 and 3305 devices. Hence, adding sleep to lgdt3304_ops will help
suspend 3304 properly from dvb_frontend_suspend().
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Kconfig entry for "Micronas DRX-J demodulator" defaults to modular
if DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, because MEDIA_SUBDRV_AUTOSELECT's logic is the opposite of
the former logic.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
fix the following warnings:
m88rs2000.c:300:16: warning: symbol 'm88rs2000_setup' was not declared. Should it be static?
m88rs2000.c:318:16: warning: symbol 'm88rs2000_shutdown' was not declared. Should it be static?
m88rs2000.c:328:16: warning: symbol 'fe_reset' was not declared. Should it be static?
m88rs2000.c:366:16: warning: symbol 'fe_trigger' was not declared. Should it be static?
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Band switching didn't worked always reliably as there was one
register bit set wrong.
Thanks to Robert Schlabbach for pointing this bug and solution.
Reported-by: Robert Schlabbach <Robert.Schlabbach@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting functions for hardware filter is a bad idea, as it
breaks compilation if:
CONFIG_DVB_USB_AF9035=y
CONFIG_DVB_AF9033=m
Because the PID filter function calls would be hardcoded at
af9035.
The same doesn't happen with af9033_attach() because the
dvb_attach() doesn't hardcode it. Instead, it dynamically
links it at runtime.
However, calling dvb_attach() multiple times is problematic,
as it increments module kref.
So, the better is to pass one parameter for the af9033 module
to fill the hardware filters, and then use it inside af9035.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PID filter and export it via symbol.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It was possible that tuner_frequency variable, used for carrier offset
compensation, was uninitialized. That happens when tuner
.get_frequency() callback is not defined.
Currently that case is not possible as only used tuner has this callback.
Coverity CID 1166057: Uninitialized scalar variable (UNINIT)
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1166051: Logically dead code (DEADCODE)
TS clock calculation could be more accurate, but as it is not,
remove those unused clock speeds.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are two troubles there:
1) the bit error measure were not accumulating;
2) it was missing the bit count.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function 'ctrl_get_qam_sig_quality':
drivers/media/dvb-frontends/drx39xyj/drxj.c:9468:6: warning: variable 'ber_cnt' set but not used [-Wunused-but-set-variable]
u32 ber_cnt = 0; /* BER count */
^
By reading the comment, it is said that BER should be calculated as:
qam_pre_rs_ber = frac_times1e6( ber_cnt, rs_bit_cnt );
Also, it makes sense to take the mantissa into account, so fix the
code to do what's commented.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that everything is set, let's enable DVBv5 stats, for
applications that support it.
DVBv3 apps will still work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of just assuming that the min resolution is 1E-6,
pass both bit error and bit counts for userspace to calculate
BER. The same applies for PER, for 8VSB. It is not clear how
to get the packet count for QAM. So, for now, don't expose PER
for QAM.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the stats internally to use DVBv5. For now, it will keep
showing everything via DVBv3 API only, as the .len value were
not initialized.
That allows testing if the new stats code didn't break anything.
A latter patch will add the final bits for the DVBv5 stats to
fully work.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We'll need to use this function. Restore it from the
git history.
This function will be used on the next patch.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
State is already used on other places for the state struct.
Don't use it here, to avoid troubles with latter patches.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported when compiled with W=1:
drivers/media/dvb-frontends/drx39xyj/drxj.c: In function ‘ctrl_set_channel’:
drivers/media/dvb-frontends/drx39xyj/drxj.c:10340:26: warning: variable ‘common_attr’ set but not used [-Wunused-but-set-variable]
struct drx_common_attr *common_attr = NULL;
^
drivers/media/dvb-frontends/drx39xyj/drxj.c:10336:6: warning: variable ‘intermediate_freq’ set but not used [-Wunused-but-set-variable]
s32 intermediate_freq = 0;
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This function is currently not used. However, it was meant to
be called at device release. So, add it there.
While here, remove the bad check, as reported by Dan, as
smatch warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:20041 drxj_close() warn: variable dereferenced before check 'demod' (see line 20036)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are large chunks of code at drx-j that aren't used. Most
of them are due to analog TV support. Well, just enabling them
won't make analog support work, as devices with DRX and analog
support requires an extra chip (avf4910).
We don't have drivers for it, nor the current device that uses
this frontend has support for analog TV.
So, let's just get rid of this code. If latter needed, this
patch can easily be reverted from git history.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by the kbuild test robot <fengguang.wu@intel.com>:
drivers/built-in.o: In function `em28xx_dvb_init':
em28xx-dvb.c:(.text+0x876f2c): undefined reference to `drx39xxj_attach'
That happens when CONFIG_VIDEO_EM28XX_DVB is selected, and neither
CONFIG_MEDIA_SUBDRV_AUTOSELECT or DVB_DRX39XYJ is selected.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fixes the following warnings:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:65: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1679:71: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:52: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drx39xyj/drxj.c:1681:58: warning: Using plain integer as NULL pointer
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
No functional changes, but removes a duplicate check, if
!state->type_A.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/dvb-frontends/drx39xyj/drxj.c:1039:16: sparse: symbol 'drxj_default_aud_data_g' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Delay possible I2C gate close a little bit in order to see if there
is next message coming to tuner in a sequence.
Also, export private muxed I2C adapter. That is aimed only for SDR
extension module as SDR belongs to same RTL2832 physical I2C bus (it
is physically property of RTL2832, whilst it is own kernel module).
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was a deadlock between master I2C adapter and muxed I2C
adapter. Implement two I2C muxed I2C adapters and leave master
alone, just only for offering I2C adapter for these mux adapters.
Reported-by: Luis Alves <ljalvs@gmail.com>
Reported-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
RTL2832 provides gated / repeater I2C adapter for tuner.
Implement it as a muxed I2C adapter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Most of those were reported by checkpatch.pl...
debug module parameter is not used anywhere so remove it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All used tuners has get_if_frequency() callback and that parameter
is not needed and will not needed as all upcoming tuner drivers
should implement get_if_frequency().
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Currently, there's just one device using this frontend: PCTV 80e,
and it works on serial mode.
Change the default here to serial mode. If we add more devices,
then this option should be set via config structure.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The cfg_mpeg_output has more fields than what it is initialized
when the code is called. Be sure to initialize everything before
use, in order to avoid random behaviors.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just like the windows driver, disable OOB after setting the driver
version.
Acked-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
