semaphore to mutex conversion.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
build tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Speed up i2c_smbus_write_block_data and i2c_smbus_read_i2c_block_data
a bit by using memcpy instead of an explicit loop.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop 3 useless macros in the w83792d hardware monitoring driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use arrays of attributes in the w83792d driver.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Yuan Mu <ymu@winbond.com.tw>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch refactors SENSOR_DEVICE_ATTR_2 macro, following pattern set by
SENSOR_ATTR. First it creates a new macro SENSOR_ATTR_2() which expands
to an initialization expression, then it uses that in SENSOR_DEVICE_ATTR_2,
which declares and initializes a struct sensor_device_attribute_2.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
scx200_acb is only useful on a few Geode-based systems, and won't
compile on non-x86 systems due to the lack of asm/msr.h, as reported
by Andrew Morton. Thus, we should make that driver depend on X86.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
scx200_acb: Fix and speed up the poll loop
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
scx200_acb: remove use of lock_kernel()
Signed-off-by: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch below converts a few i2c semaphores to mutexes
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert the f71805f driver to use arrays of attributes. This shrinks the
compiled module from 12.0 kB to 9.6 kB. We certainly should do the same
for as many hardware monitoring drivers as possible.
This, together with a nice chip design by Fintek, makes this driver
very small, both in terms of number of lines of code and memory
consumption.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert individual sensors to sensor-attr arrays by each sensor type,
and initialize them in loops instead of long blocks of individual calls.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch refactors SENSOR_DEVICE_ATTR macro. First it creates a new
macro SENSOR_ATTR() which expands to an initialization expression, then
it uses that in SENSOR_DEVICE_ATTR, which declares and initializes a
struct sensor_device_attribute.
IOW, SENSOR_ATTR() imitates __ATTR() in include/linux/device.h.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't need to keep track of available buffers, it is simpler
to just compute the value (ala e1000). Don't need tes on link up
because should always have available buffers then.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't free transmit buffers until the whole set of transmit descriptors
has been marked as done. Otherwise, we risk freeing a skb before the
whole transmit is done.
This changes the transmit completion handling from incremental to a
two pass algorithm. First pass scans and records the start of the last
done descriptor, second cleans up until that point.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the error case we call skge_rx_reuse twice. This is harmless
but unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver was using dev_alloc_skb which reserves space for the
Ethernet header. This unnecessary and it should just use alloc_skb,
also by using GFP_KERNEL during startup it won't run into problems when
a user asks for a huge ring size or mtu and potentially drains the
reserved atomic pool.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The skge driver aligns the header on the initial receive buffers, but
but doesn't on followon receive buffer allocations.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Transmit buffers are always freed with interrupts enabled (softirq),
so we can just call dev_kfree_skb.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unicast packets are shown as multicast, real multicast packets are missing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After a scan, we weren't switching back to the original channel if we
were associated with an AP. So NetworkManager's periodic scans would
disrupt connectivity until the ESSID was manually set again. Fix that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 659, 660) spotted this resource leak on
PCI probe error path. Free private data structure if pci_enable_device()
fails.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 58) spotted this duplicated idx != 0
validation for unicast keys in prism2_ioctl_siwencodeext().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 452, 453, 454, 455, 456) spotted this
unlikely read overrun of CIS buffer. Abort if CISTPL_CONFIG or
CISTPL_MANFID would not fit in buffer.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 930) spotted this double free on error path
(allocation failure). Do not free these here since generic error path
will take care of this.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 273) spotted this inconsequent NULL checking
(unconditionally dereferencing directly after checking for NULL
isn't a good idea). Return immediately to avoid this.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Coverity checker (CID: 59) noted that the call to prism2_hw_reset()
was dead code. Move prism2_hw_reset() call to a place where it is
actually executed.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Observed problems when multiple processes request scans and subsequently
scan results. This causes a scan result request to hit card registers
before the scan is complete, returning an incomplete scan list and
possibly making the card very angry. Instead, cache the results of a
wireless scan and serve result requests from the cache, rather than
hitting the hardware for them.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number 2312 was used all over the place to refer to the card's
default MTU. Make it a #define and use that everywhere rather than the
number.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Show the specific device that driver messages are about.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
