New bindings use "fsl,t1040-ucc-uart" as the compatible for qe-uart.
So add it.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The maximum bitrate supported depends on the clock rate used in BRG.
This is stored in port.uartclk during probe. Respecting the 16x
oversampling higher bitrates can be supported.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Timur Tabi <timur@tabi.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
when platform_driver_register broken, we should unregister ucc_uart_driver
Signed-off-by: Libo chen <libo.chen@huawei.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Here we start with tty_buffer_request_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We transform the offenders into a test of irq <= 0 which will be ok while
the ARM people get their platform sorted. Once that is done (or in a while
if they don't do it anyway) then we will change them all to !irq checks.
For arch specific drivers that are already using NO_IRQ = 0 we just test
against zero so we don't need to re-review them later.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UCC UART driver is missing a call to uart_update_timeout().
Without this call, attempting to close the port after outputting large
amounts of data (i.e. using tty and uart buffering) results in long
timeouts before the port will actually be shut down.
For example, cat a large file to a UCC UART port. With the current
driver, the port will stay open for 30 seconds after the last byte
of data is output. But with this patch, the port is closed as
expected, just after the data has been output (tx fifos empty).
Signed-off-by: Chuck Meade <chuck@ThePTRGroup.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
linux/tty_flip.h is included in linux/serial_core.h. But this may (and
will) change in the future. Then we would get build errors such as:
.../tty/serial/max3107.c: In function ‘put_data_to_circ_buf’:
.../tty/serial/max3107.c:149:2: error: implicit declaration of function ‘tty_insert_flip_string’
So fix all the drviers which call tty flip buffer helpers to really
include linux/tty_flip.h. And also make sure that those include
linux/tty.h when operating with struct tty_struct.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/tty/serial/ucc_uart.c: In function 'qe2cpu_addr':
drivers/tty/serial/ucc_uart.c:238:2: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'dma_addr_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a call to of_node_put in the error handling code following a call to
of_find_compatible_node or of_find_node_by_type.
This patch also substantially reorganizes the error handling code in the
function, to that it is possible first to jump to code that frees qe_port
and then to jump to code that also puts np.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
local idexpression x;
expression E,E1,E2;
statement S;
@@
*x =
(of_find_node_by_path
|of_find_node_by_name
|of_find_node_by_phandle
|of_get_parent
|of_get_next_parent
|of_get_next_child
|of_find_compatible_node
|of_match_node
|of_find_node_by_type
|of_find_node_with_property
|of_find_matching_node
|of_parse_phandle
)(...);
...
if (x == NULL) S
<... when != x = E
*if (...) {
... when != of_node_put(x)
when != if (...) { ... of_node_put(x); ... }
(
return <+...x...+>;
|
* return ...;
)
}
...>
(
E2 = x;
|
of_node_put(x);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Timur Tabi <timur@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Get rid of users of of_platform_driver in drivers/serial. The
of_platform_{,un}register_driver functions are going away, so the
users need to be converted to using the platform_bus_type directly.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The serial drivers are really just tty drivers, so move them to
drivers/tty/ to make things a bit neater overall.
This is part of the tty/serial driver movement proceedure as proposed by
Arnd Bergmann and approved by everyone involved a number of months ago.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Rogier Wolff <R.E.Wolff@bitwizard.nl>
Cc: Michael H. Warfield <mhw@wittsend.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
