Set the default status for UARTs to disabled in the zynq-7000.dtsi file
and let board dts files enable the UARTs on demand.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When zImage is loaded into RAM at a low address but TEXT_OFFSET
is set higher, we risk overwriting ourself with the page table
needed to turn on the cache as it is located relative to the relocation
address. Let's defer the cache setup after relocation in that case.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reported-by: Stephen Boyd <sboyd@codeurora.org>
Tested-by: Stephen Boyd <sboyd@codeurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the missing VPU devicetree node for i.MX27 CPUs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The gpio-ranges properties in vf610.dtsi were written according to an
older version of the GPIO bindings. Unfortunately, these were changed
incompatibly in commit 86853c8 "gpio: add gpio offset in gpio range
cells property". This patch adds the missing required extra cell in each
gpio-ranges property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10,
so add a regulator controled by GPIO_4_10 for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds name for NOR flash. This keeps compatibility for
commandline partitions parsing from old bootloaders and make name
of device same for DT and non-DT boot.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the WEIM NOR for imx6q{dl}-sabreauto boards.
For the pin conflict with SPI NOR, its status is set to "disabled".
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add two pinctrls for WEIM:
one for the weim nor, another for the chipselect.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add the clock and compatible information for the weim.
Also adds the weim label.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.
In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.
The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[Steffen: split up patch into tqma53+mba53 part]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add properties to make use of pca9554 gpio expander.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable the sgtl5000 found on MBa53 mainboard.
Also enable audio muxer and ssi, which are needed for sound to work.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As the displays are optional and we have more than one, also
set the status of the parallel display and the ldb to disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds the Television Encoder (TVEv2) device tree node
to the i.MX53 dtsi.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
FEC (KSZ8001L) reset pin is connected to GPIOC30.
Add this definition to dts.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add a group to the fec pinctrl, for use with MII interface.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Configure the data and tag latency for the L2 cache. This improves the
system performance.
This configuration is taken from Freescale's kernel patch
"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]
which does
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL));
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL));
In this patch we are doing the same via the device tree.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1
Since the SPI/NOR has pin conflict with the WEIM NOR,
we disable the spi/nor by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and
MX6Q_PAD_NANDF_CS3__NAND_CE3_B.
Just remove them.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This adds support for the Ka-Ro TX53 System-On-Module.
As a baseboard is needed to operate it, only a *.dtsi and no Makefile entry.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for the DENX M53EVK board. The board currently supports
NAND, Ethernet, UART, CAN, I2C.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.
Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for NAND on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of I2C2 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of I2C1 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for different mux of CAN1 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pinctrl data for the AUDMUX4 on MX53.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This allows to order the i2c character devices correctly,
so that /dev/i2c-0 corresponds to i2c1, /dev/i2c-1 corresponds
to i2c2, and so on. Currently they are ordered by register
address.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CFA-10057 is a breakout board for the CFA-10036 that has Ethernet,
USB and a 4.3" LCD screen on it.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CFA-10055 is yet another breakout board for the CFA-10036, and is
basically a CFA-10037, with the screen and LCD controller found on the
CFA-10049.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The early prototypes had the chip select pin for the LCD controller
wired on the GPIO 3-23, while the production run of the CFA-10049 have
this chip select on the GPIO 3-5.
Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Make use of RTS/CTS lines on AUART0 and register AUART1 and AUART2
which are routed onto a pin header.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The OLED display can work faster. Change the i2c controller clock
frequency to remove the tearing effect that can be seen on the display.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The SSD1307 was used in an early prototype that will never get
distributed. The final board now has a SSD1306 instead, that has its own
power generation unit and thus doesn't need any PWM. The panel attached
to it also changed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MX28 has the same DIGCTL block as MX23, so adjust the compatible string to
reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical since
it fixes a problem where multiplatform kernels panic on all but prima2
hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=c555
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703
This registers the memory ranges for I/O, non-prefetched and
prefetched memory and configuration space for the PCIv3 bridge
and let us fetch these basic memory resources from the device
tree in the device tree boot path. Remove the stepping stone
platform device. This is an either/or approach - the platform
data path is mutually exclusive to the plain platform data
path and provided addresses from the device tree have to be
correct.
This adds the interrupt-map property to the PCIv3 DTS file
and makes the bridge obtain mappings from the device tree.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cubieboard makes use of the first two i2c controllers found on the
Allwinner A10; i2c-0 is used internally for the PMIC, while i2c-1
is exposed on the board headers. This patch enables them in the device
tree.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
The A13-Olinuxino makes use of the 3 i2c controllers found on the Allwinner
A13. Enable them in the device tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
The i2c controller found on the Allwinner A13 has only one muxing option
available for each controller. Add them to the dtsi
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
The i2c controller found on the Allwinner A10 has only one muxing option
available for each controller. Add them to the dtsi
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
The Allwinner A10 and A13 both have 3 i2c controller embedded.
Add those to the common sunxi dtsi.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRu5FQAAoJEAf03oE53VmQB40H/RfSFjAMRak2yPSb+4Cw2038
3BQ7iDowps/jJwD7D79SZOY44X+dOMfGO5Pj9C1J61y5ThhiS3QDFnpfzHb74Cl8
AHLRI9ugG496pdKk6aWjAq4oJozDBrwznnwTJpZshrkSkfOklHjhd/Z5uTIBW3pn
gQL9tbcTmjqhemhRB160ZHaJebMZBDZgAtft4pVt2JFjXZCokkHLxpf57z4S79D9
RJ84AU/o2IlQnrcY8fwnyWiU9LNeFzEF+bhNH7XiSoN5suTAdIN6grmHvkqdbSon
GCiAGp2samBoewnSa+Je32jXdqHORnxHZ6gaZsj+WOnz8zqJG7VNpc4KCJs0Hos=
=MvZy
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://github.com/at91linux/linux-at91 into next/drivers
From Nicolas Ferre:
Adding the DT support to USB gadget High-Speed aka usba.
* tag 'at91-drivers' of git://github.com/at91linux/linux-at91:
USB: gadget: atmel_usba: add DT support
USB: gadget: atmel_usba: allow multi instance
USB: gadget: atmel_usba: move global struct usba_ep usba_ep to struct usba_udc
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
ARM: at91: dt: use #include for all device trees
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/at91sam9260.dtsi
arch/arm/boot/dts/sama5d3.dtsi
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRu5r2AAoJEAf03oE53VmQvAsIAMa06mb42kGJQ6JhUV0HcL+8
+a2FHN076DreWEtM5vq9ibIEF2pnz+XHafUYGRfjfYRsbEfy41N0OmISNBwIRgP6
yKB6ZnGQp21Fw/SwOGntuEw0PH9bQmM9pNYttMlBfvMlM3TdFWc2fztwvqpP71x4
a1zOsLRNYLk4WO33gh50bRTQeS81GRvn3hrGPKKFXuC7AQ0TCHOH/l1c1Fo5INpk
TiQMy5JvkrJNSerdq23u5uAp2zstuhiVMbSY6eWQwJy1RfOSqVYY91KzGKGpOPT2
g6LB/Z6sZ5wwJ8jbbPV1XAEl45oojPDyNl+KxJc5gir5wfWEVpoayRt1Nfggz98=
=MZkL
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Again some nice DT updates for AT91:
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9m10g45ek add udc DT support
ARM: at91: sam9g45 add udc DT support
ARM: at91: sam9x5ek add udc DT support
ARM: at91: sam9x5 add udc DT support
ARM: at91: dt: at91sam9x5: add SPI DMA client infos
ARM: at91: dt: switch DMA DT bindings to pre-processor
ARM: at91: dt: add header to define at_hdmac configuration
- Switch to using the sun5i clocks for the A13
- Register the pio node as an interrupt controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3kFd
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.11' of git://github.com/mripard/linux into next/dt
From Maxime Ripard:
Allwinner SoCs DT additions for 3.11
- Switch to using the sun5i clocks for the A13
- Register the pio node as an interrupt controller
* tag 'sunxi-dt-for-3.11' of git://github.com/mripard/linux:
ARM: sunxi: dt: Register the pio node as interrupt controller
ARM: sun5i: Update the clock compatible strings
Signed-off-by: Olof Johansson <olof@lixom.net>
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=9wS3
-----END PGP SIGNATURE-----
Merge tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
Cleanups for MSM for 3.11
These are a handful of cleanups to the MSM tree. The gpio cleanups
get us closer to having proper pinmux and gpio support.
* tag 'msm-cleanup-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
mfd: ssbi: Use devm_* and simplify code
gpio: msm: Add device tree and irqdomain support for gpio-msm-v2
ARM: msm: Remove gpiomux-v2 and re-organize MSM_GPIOMUX configs
msm: iomap: Remove unused bases and mappings
msm: Remove unused file core.h
ARM: msm: Remove init_irq declaration in machine description
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/boot/dts/msm8660-surf.dts
arch/arm/boot/dts/msm8960-cdp.dts
I don't expect these to be necessary for stable, since the fixes are
to recently added code. The strncpy fix is only in debug code that
isn't normally compiled or used (and is being removed in upcoming
patches).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=XyCL
-----END PGP SIGNATURE-----
Merge tag 'msm-fix-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From David Brown:
Some minor fixes for MSM for 3.11
I don't expect these to be necessary for stable, since the fixes are
to recently added code. The strncpy fix is only in debug code that
isn't normally compiled or used (and is being removed in upcoming
patches).
* tag 'msm-fix-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
gpio: msm-v1: Remove errant __devinit to fix compile
mfd: ssbi: Add MODULE_DEVICE_TABLE
ARM: dts: msm: Fix bad register addresses
arch: arm: mach-msm: using strlcpy instead of strncpy
Signed-off-by: Olof Johansson <olof@lixom.net>
I don't expect these to be necessary for stable, since the fixes are
to recently added code. The strncpy fix is only in debug code that
isn't normally compiled or used (and is being removed in upcoming
patches).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJRu1dtAAoJEOa6n1xeVN+C1JIQAMbo/i20+rRdXutDqwQa+XY7
TaDi4Ltqb5xE8OOIToJlUeI6pJzWIrM5KvSDLJ6BVd1UYm5BEye/oxI6T95F+aZT
iND8nD8ZFJAGbUoviw+1WOQVXK8kyZFv7oDqmh5F5NieKD5UNoc0W5r3um0wrZC7
33QLl7P0sNg9H98IkbnpA8nMmWnrVs7HXPZjRgoEycj+BtLT2yIx7CSANIbBjspz
CLBpjvOEzG0Qv86jp6FzRS7oSz7AAy2fTIVvHCyrCtvXY8X2CnXuvMk+Ppuby0rN
M95r3g03gaL4P2fgehp2p3Kg4dBQ05h8dMtdc53/TU8ow1NCXG7OXZ10jm9sBoMw
K7HUYwV+mkWkpM6DFv0Sf5YEOOr2lVAqnJyDvd3MfihC6QTlOVCvPuYMqYndpDmd
yOWhS7a4NBanJxXJI9MAR64X36+Zt9VKzKTTn8sMzNZvotMl6tAS03KCNB6NeIGQ
XmYjTUIkzynw7YFdCwAxVtN8KegsNe2t3tWUyoNWiZbEPOVISl1z7NwsqXS4sJKU
p7QpqQRGBIw1QMPnbNhLGR4PouTSXK2iNMXjrpcTD85olgzV1K0Za4qFvOdcTZCY
PeVHfhG1xTGPoXj/UHr5RG4oAswbfLvrtGxp6AAS3yOJt0P6rLZ5BwpqgQdtTScd
UjmLUYDIUWnF3dSrkAy1
=XyCL
-----END PGP SIGNATURE-----
Merge tag 'msm-fix-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/fixes-non-critical
From David Brown:
Some minor fixes for MSM for 3.11
I don't expect these to be necessary for stable, since the fixes are
to recently added code. The strncpy fix is only in debug code that
isn't normally compiled or used (and is being removed in upcoming
patches).
* tag 'msm-fix-for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
gpio: msm-v1: Remove errant __devinit to fix compile
mfd: ssbi: Add MODULE_DEVICE_TABLE
ARM: dts: msm: Fix bad register addresses
arch: arm: mach-msm: using strlcpy instead of strncpy
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch contains all device tree updates for Tegra boards.
The changes are:
* Converted all DT files to use the C pre-processor, to support the use
of named constants. This included use of defines for GPIO, IRQ, and
clock constants.
* Enabling new features such as:
- SPI on Dalmore.
- Audio on Dalmore and Beaver.
- gpio-leds on Beaver.
- Power-supply/batter linkage on Dalmore.
* A minor fix to the RAM size node on Beaver.
It is based on previous pull request tegra-for-3.11-deps-for-usb
followed by a merge of tegra-for-3.11-deps-for-clk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4sJe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.11-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree updates
This branch contains all device tree updates for Tegra boards.
The changes are:
* Converted all DT files to use the C pre-processor, to support the use
of named constants. This included use of defines for GPIO, IRQ, and
clock constants.
* Enabling new features such as:
- SPI on Dalmore.
- Audio on Dalmore and Beaver.
- gpio-leds on Beaver.
- Power-supply/batter linkage on Dalmore.
* A minor fix to the RAM size node on Beaver.
It is based on previous pull request tegra-for-3.11-deps-for-usb
followed by a merge of tegra-for-3.11-deps-for-clk.
* tag 'tegra-for-3.11-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (21 commits)
ARM: tegra: enable audio on Beaver
ARM: tegra: enable audio on Dalmore
ARM: tegra: add power-supplies link between battery and charger
ARM: tegra: add audio-related nodes to Tegra114 DT
ARM: tegra114: convert device tree files to use CLK defines
ARM: tegra30: convert device tree files to use CLK defines
ARM: tegra20: convert device tree files to use CLK defines
ARM: tegra: Add charger subnode to tps65090 node
ARM: tegra: convert device tree files to use IRQ defines
ARM: tegra: convert device tree files to use GPIO defines
ARM: tegra: create a DT header defining GPIO IDs
ARM: tegra: use #include for all device trees
ARM: tegra: Add gpio-leds to Tegra30 Beaver
ARM: tegra: fix memory size on Beaver
ARM: tegra: enable spi4 on Dalmore
ARM: tegra114: create a DT header defining CLK IDs
ARM: tegra30: create a DT header defining CLK IDs
ARM: tegra20: create a DT header defining CLK IDs
ARM: tegra: update device trees for USB binding rework
ARM: tegra: modify ULPI reset GPIO properties
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Just one patch this time: enable the LED via gpio-leds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJRuT7vAAoJEJuNpwkmVCGc14EQAIGfMzSI47biW9MlVqEfb7Q1
4q+PotOL6XZgBQLV2xRAgi/DKlHNF/6M/63pwAWNWBrzvdoCd4LdZqomB3L0O2Ao
BvTMTRWG6UsgyECgTWliiik99DWDpTi5rhwJ6nl9IocCv+bA7yD2e4H2wp0jzvcz
QagWz3I0f2tP17feZdm4JxrF0vofWLVtGn/+67/ZMfAergRNnu6pdGqWu6d+a7T8
DbBLQFjXa1ezmeYNb8NzlGCY708EfgumiKh8b8AnVhV9aIl0GZo/Wd0F2axbWKEP
EhuBPit0Bt/H4PLEbKhgMnvhO3FjRidKS93Eht3p6rz6lPZMhuHa8slcfYrYEYxG
AeDEucfUU681vUIpmbs/PZI2tb5LHKDDHActQE7V8o13jDEXF1U2pU5EzX2+nk42
jRgT5noGvVtFfD7AnBdW7Do9wicgXdMeP0TaWWs2LcZfvpTtPk4AJvqxPJUmxL4t
Rcs0gZYP2vGddntf518u5hmhlOV80tA6p6FdyjEmxiJOItXcojnimuMprHT+4agX
c5vn60Dcor/RM9LiZbZQXPzqhDUy+sua9JwHFbtRbhgBHZShgpMp51546hiUPjpD
YzGuFXobnNg23TepKB1VB3aLzW+05Hx0YTda37JwYPod8EGQjd7T+IxibxU1w4Xh
jRVjo0fJBw3WVCduV1wZ
=uRgd
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-for-3.11-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi into next/dt
From Stephen Warren:
ARM: bcm2835: device tree updates
Just one patch this time: enable the LED via gpio-leds.
* tag 'bcm2835-for-3.11-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi:
ARM: bcm2835: Add Raspberry Pi's ACT LED to DT
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=cph0
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Device tree patches for ux500, basically trees and auxdata:
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: drop any 0x prefix from I2C DT devices
ARM: ux500: Allocate correct amount of memory for the u8540 in DT
ARM: ux500: Provide auxdata to ux500 ASoC driver
ARM: ux500: Add DT regulators for ab8500-codec
ARM: ux500: Correct anamic2 typo in DT files
ARM: ux500: Fix trivial typo in v-anamic1 comment
ARM: ux500: Reduce PRCMU reg-names to shorter form for u8540 DT
ARM: ux500: Add an auxdata entry for MUSB for clock-name look-up
ARM: ux500: cut chip-select GPIOs from SSP device
ARM: ux500: use symbolic names for interrupt flags
ARM: ux500: use #include syntax to include *.dtsi.
ARM: ux500: bump MMC/SD max frequency for DT boots
ARM: ux500: Apply other compatible name to the u8540 DTS file
pinctrl/nomadik: Standardise Pinctrl compat string for DBx5x based platforms
ARM: ux500: Standardise Pinctrl compatible string for DBx5x based platforms
ARM: ux500: Standardise DBx5x0 based Pinctrl compat string in the DTS
crypto: ux500/hash - Enable DT probing of the driver
crypto: ux500/cryp - Enable DT probing of the driver
ARM: ux500: enable the crypto and hash on all dbx500
ARM: ux500: Provide an AUXDATA entry for ux500-hash
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series removes the hardcoded register base address for mvebu.
Depends:
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJRujY/AAoJEAi3KVZQDZAeQ/8H/186TUo1jWJJP/Tdp6Rg09qK
FeZeVH9YrViLO2g2iO338TlfIjshJW8HgMv8tnuJo9xLz5wtws3Dpv5BpcYoGoKs
vU/d1EZC4vJTs5IZ2fS6p0LpvV8YrUYVi9v7uPWHFx6DYGznuHPP/q8Hu6Pa0Tok
MoPNAihBYMEhePGuBQo1j3xPtteifJy/CUv5iSrAAJSEI5zGRc7QO/0ItS2gc9qy
odFZKTZnGPlp/79np4I1/cjNTRuD5kf/9IzNFxl4ZL4X7Nre9J+8IFoPU671EDw1
XMBEtf6ThO6Z8oLiVPxeHlSLO2o7xQj7VEAUoSEsiK4whJAfxFiOqIiIC5SXfDA=
=hKzx
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
mvebu register map changes for v3.11
This series removes the hardcoded register base address for mvebu.
Depends:
- mvebu/fixes-non-critical (up to tags/fixes-non-3.11-1)
- mvebu/cleanup (up to tags/cleanup-3.11-3)
* tag 'regmap-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: disable DEBUG_LL/EARLY_PRINTK in defconfig
arm: mvebu: add another earlyprintk Kconfig option
arm: mvebu: don't hardcode the physical address for mvebu-mbus
arm: mvebu: don't hardcode a physical address in headsmp.S
arm: mvebu: remove hardcoded static I/O mapping
arm: mvebu: move cache and mvebu-mbus initialization later
arm: mvebu: avoid hardcoded virtual address in coherency code
arm: mvebu: remove dependency of SMP init on static I/O mapping
arm: mvebu: fix length of Ethernet registers area in .dtsi
arm: mvebu: fix length of SATA registers area in .dtsi
arm: mvebu: mark functions of armada-370-xp.c as static
ARM: mvebu: Remove init_irq declaration in machine description
ARM: Orion: Remove redundant init_dma_coherent_pool_size()
Signed-off-by: Olof Johansson <olof@lixom.net>
- mvebu
- set aliases for ethernet interfaces
- PCIe range for armada-xp-db
- rm unused properties on A370
- kirkwood
- assign sheevaplug pinmuxs to correct devices
- enable second PCIe port for ts219
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJRujTWAAoJEAi3KVZQDZAewwYH/iWl8JcRm0i0xyjYjj6v+XMk
2NauOq3A5yTWbI0H3oXi8QH0BBlUie30SuT85O675KS9no0tIbv8JlLx3PfhTjoB
3hrDKkhcD6jTqg7TgWL9w3Qdq2S0/XLgoZ4RDo35nrXsCodpkr5XaEPJP3ES1Zo+
n57cAgyw7edhohcIT/mKSv5WyOajbU4uWPxBr9i8sqZf9uTFOyOYQpWZMCvbJKc2
/MrQ0UfRhMgymcaYiO5oqihYn8C0HhxRBno1muXemR4Ovaxgdp040gPB0QnmGONo
oibfWbOWnlx6KK8I/B231uCWuDEFm5q1sr/L/e17f1hi0S+R6fwREVgH/5Hf6MQ=
=UXHW
-----END PGP SIGNATURE-----
Merge tag 'dt-3.11-5' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
mvebu dt changes for v3.11 (round 5)
- mvebu
- set aliases for ethernet interfaces
- PCIe range for armada-xp-db
- rm unused properties on A370
- kirkwood
- assign sheevaplug pinmuxs to correct devices
- enable second PCIe port for ts219
* tag 'dt-3.11-5' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: ts219: Enable second PCIe port in DT.
ARM: mvebu: Remove device tree unused properties on A370
arm: mvebu: armada-xp-db: ensure PCIe range is specified
arm: kirkwood: sheevaplug: move pinmux configs to the right devices
ARM: mvebu: set aliases for ethernet controllers
Signed-off-by: Olof Johansson <olof@lixom.net>
minimal support for am43x SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3bVH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
From Tony Lindgren:
Omap SoC changes. Mostly improves am33xx support, and adds
minimal support for am43x SoCs.
* tag 'omap-for-v3.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43x: SRAM base and size
ARM: OMAP2+: AM43x: GP or HS ?
ARM: OMAP2+: AM43x: early init
ARM: OMAP2+: AM43x: static mapping
ARM: OMAP2+: AM437x: SoC revision detection
ARM: OMAP2+: AM43x: soc_is support
ARM: OMAP2+: AM43x: kbuild
ARM: OMAP2+: AM43x: Kconfig
ARM: OMAP2+: separate out OMAP4 restart
ARM: AM33XX: clk: Add clock node for EHRPWM TBCLK
ARM: OMAP3: clock data: get rid of unused USB host clock aliases and dummies
ARM: OMAP2+: AM33xx: Add missing reset status info to GFX hwmod
+ Linux 3.10-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vzQW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
From Tony Lindgren:
Non-critical fixes for omaps for v3.11 merge window.
* tag 'omap-for-v3.11/fixes-non-critical-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap-usb-host: Fix memory leaks
ARM: OMAP2+: Fix serial init for device tree based booting
arm/omap: use const char properly
ARM: OMAP2+: devices: Do not print error when dss_hdmi hwmod lookup fails
ARM: OMAP2+: devices: Do not print error when DMIC hwmod lookup fails
ARM: OMAP2+: devices: Do not print error when McPDM hwmod lookup fails
ARM: OMAP: add vdds_sdi supply for omapdss_sdi.0
ARM: OMAP: add vdds_dsi supply for omapdss_dpi.0
ARM: OMAP: fix dsi regulator names
+ Linux 3.10-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
- mvebu
- fix register area length in dtsi for ethernet and sata
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPK5AAoJEAi3KVZQDZAeY0IH/2zCJX+nmBBw9omcrDg3lXaU
YKrpL6d/sV1Y+gyC6Xa8OLvmOZFndwt5ePh6RRprM7wDybw5JE6inCXtLUN31f0W
ARjX6asJkPk/NqDx8Bhs+OzI157cGHKnDOTzemE0dMVtN4dBnEApKMB2w+8pzGPK
SirwBvHuaIf5eNdIv9Vnj/UguMH7UKuPb7xKnq52FavkRcHWXXJNIDEibzwOOoBG
KRjk1yBL3Spva51UwZ2Mgv+8J71y5KOGBUjEIHbVwcxl7lPQ37fP1yWDlreG0qdV
xDTiB1wwfg8/IH/M+2z0AAKK4s/ngfLujZZZsHL9HrTudstThEaTi9T6scLtqOM=
=BmX7
-----END PGP SIGNATURE-----
Merge tag 'tags/fixes-non-3.11-1' into mvebu/regmap
mvebu fixes non-critical for v3.11 (round 1)
- mvebu
- fix register area length in dtsi for ethernet and sata
- DT support for the MFD, TSC and ADC driver & platform device support,
which has no users, has been killed.
- iio_map from last series is gone and replaced by proper nodes in the
device tree.
- suspend fixes which means correct data structs are taken and no
interrupt storm
- fifo split which should problem with TSC & ADC beeing used at the same
time
- The ADC channels are now checked before blindly applied. That means the
touch part reads X, Y and Z coordinates and does not mix them up. Same
goes for the IIO ADC driver.
- The IIO ADC driver now creates files named in_voltageX_raw where X
represents the ADC line instead of a number starting at 0. A read from
this file can return -EBUSY in case touch is busy and the ADC didn't
collect a value.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=VGdP
-----END PGP SIGNATURE-----
Merge tag 'am335x_tsc-adc' of git://breakpoint.cc/bigeasy/linux
A complete refurbished series inclunding:
- DT support for the MFD, TSC and ADC driver & platform device support,
which has no users, has been killed.
- iio_map from last series is gone and replaced by proper nodes in the
device tree.
- suspend fixes which means correct data structs are taken and no
interrupt storm
- fifo split which should problem with TSC & ADC beeing used at the same
time
- The ADC channels are now checked before blindly applied. That means the
touch part reads X, Y and Z coordinates and does not mix them up. Same
goes for the IIO ADC driver.
- The IIO ADC driver now creates files named in_voltageX_raw where X
represents the ADC line instead of a number starting at 0. A read from
this file can return -EBUSY in case touch is busy and the ADC didn't
collect a value.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5U0j
-----END PGP SIGNATURE-----
Merge tag 's3c24xx-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim, DT changes for s3c24xx.
* tag 's3c24xx-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add devicetree support for s3c2416-smdk2416
Signed-off-by: Olof Johansson <olof@lixom.net>
This cleans up the gpio-msm-v2 driver of all the global define usage.
The number of gpios are now defined in the device tree. This enables
adding irqdomain support as well.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=O9AH
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Beaver uses the RT5640 audio CODEC. Instantiate this on the I2C bus, and
add the top-level "sound" node to hook everything together and provide a
"sound card" device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Dalmore uses the RT5640 audio CODEC. Instantiate this on the I2C bus.
Enable the relevant Tegra I2C controller. Add the top-level "sound" node
to hook everything together, and provide a "sound card" device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The power supply core now supports detecting linkages between batteries
and chargers through the use of the power-supplies property. Adding
this to the battery, the core will use the phandle list to find
the associated charger and pair them up. This facilitates notifications
from the charger to the battery when ac power is dissconnected
or connected for instance.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The TSC part allows to specify the input lines. The IIO part assumes
that it usues always the last few, that means if IIO has adc-channels
set to 2 it will use channel 6 and 7. However it might make sense to use
only 6.
This patch changes the device property (which was introduced recently
and was never in an official release) in a way that the user can specify
which of the AIN lines should be used. In Addition to this, the name is
now AINx where x is the channel number i.e. for AIN6 we would have 6.
Prior this, it always started counting at 0 which is confusing. In
addition to this, it also checks for correct step number during reading
and does not rely on proper FIFO depth.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Add support for core multifunctional device along
with its clients touchscreen and ADC.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Instead of relying on CONFIG_MEMORY_START for memory
base address, let each romImage board header file
specify this information.
This is reworks code not to rely on CONFIG_MEMORY_START
which in turn is needed for ARCH_MULTIPLATFORM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the ATAGS data structure from head-shmobile.S
since a default ATAGS is already provided by the code
in arch/arm/kernel/atags_parser.c. Passing a NULL as
ATAGS is valid. For actual hardware specific setup
the fixup callback in the board code may be used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- mvebu
- fix PCIe ranges property so NOR flash is visible
- kirkwood
- fix identification of 88f6282 so MPPs can be set correctly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRtjVFAAoJEAi3KVZQDZAe4g4IAJcgufr2WBHJtGwVAGiSQLCr
gI3NjyfeJP98P7Bt/7ZyXBx5CmW3I6gVLN6Sctjpk01VISregbWv8Qos8iJx31hq
gqVmPJvaJy3dwHvq15rFMzNgsZGBTVV85wdnhppfeRTtt0nmREeJsLmgI1c5z0bw
u9BolnU1+sQn0S/TV/A4EZhyc18kAGzGqOKLOm3O4Ftrxncjq0idaSC5TOTDlA8Q
1D5bDbmaXyu7J1lqnYbbIsn9E4MTxfjbcrVnK1pEf7qhhtrmfJWiqLuay5plo/43
zMHefOc8rI74QUHxXuv6IS8QZcKKcfSJBpRCmxK6Ks74I9D6T9l7FxDb/2ckgJk=
=gHgq
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.10-4' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper, mvebu fixes for v3.10 round 4:
- mvebu
- fix PCIe ranges property so NOR flash is visible
- kirkwood
- fix identification of 88f6282 so MPPs can be set correctly
* tag 'fixes-3.10-4' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
Signed-off-by: Olof Johansson <olof@lixom.net>
Add entry for 2nd GMAC controller. Add the correct clocks for the GMAC.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Olof Johansson <olof@lixom.net>
Cc: Pavel Machek <pavel@denx.de>
CC: <linux@arm.linux.org.uk>
v2:
- Moved "disabled" status to dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
From Alexander Shiyan, this is a series of cleanups of clps711x, movig it
closer to multiplatform and cleans up a bunch of old code.
* clps711x/soc:
ARM: clps711x: Update defconfig
ARM: clps711x: Add support for SYSCON driver
ARM: clps711x: edb7211: Control LCD backlight via PWM
ARM: clps711x: edb7211: Add support for I2C
ARM: clps711x: Optimize interrupt handling
ARM: clps711x: Add clocksource framework
ARM: clps711x: Replace "arch_initcall" in common code with ".init_early"
ARM: clps711x: Move specific definitions from hardware.h to boards files
ARM: clps711x: p720t: Define PLD registers as GPIOs
ARM: clps711x: autcpu12: Move remaining specific definitions to board file
ARM: clps711x: autcpu12: Special driver for handling memory is removed
ARM: clps711x: autcpu12: Add support for NOR flash
ARM: clps711x: autcpu12: Move LCD DPOT definitions to board file
ARM: clps711x: Set PLL clock to zero if we work from 13 mHz source
ARM: clps711x: Remove NEED_MACH_MEMORY_H dependency
ARM: clps711x: Re-add GPIO support
GPIO: clps711x: Add DT support
GPIO: clps711x: Rewrite driver for using generic GPIO code
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
EXYNOS5440 includes both OHCI and EHCI usb host controllers.
This patch adds device tree nodes for both of them. And the
EHCI and OHCI controllers on exynos5440 do not need any
explicit phy configuration. So need to assign a different
compatible value for these controllers.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
G2D node got added twice in exynos4412-smdk4412.dts instead of
getting added to exynos4412-origen.dts. Remove the duplicate entry
and add it to exynos4412-origen.dts.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pin state information for DP HPD support that requires
pin configuration support using pinctrl interface.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to add vmmc regulator node at MSHC and SDHCI for ODROID-X
board file.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use the standard interrupt-controller and ARM GIC constants to
improve the readability of bcm281xx DT irq properties.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Christian Daudt <csd@broadcom.com>
Replace /include/ by #include for bcm281xx device tree
files, enabling use of the C preprocessor.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Christian Daudt <csd@broadcom.com>
Enable the second PCIe port on QNAP TS-11x/TS-21x devices as newer
revisions (rev 1.3) have a USB 3.0 chip from Etron on PCIe port 1.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
* Armadillo800eva reference DT - bring up armadillo800eva baord
using DT as much as possible
* Remove unused GIC dtsi entries for r8a7790 and r8a73a4
* Add AS3711 and CPUFreq DT bindings for kzm9g-reference
* Add irqpin DT support for marzen-reference
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=6tQE
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM-based SoC DT updates for v3.11
* Armadillo800eva reference DT - bring up armadillo800eva baord
using DT as much as possible
* Remove unused GIC dtsi entries for r8a7790 and r8a73a4
* Add AS3711 and CPUFreq DT bindings for kzm9g-reference
* Add irqpin DT support for marzen-reference
* tag 'renesas-dt-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen-reference: add irqpin support in DT
ARM: shmobile: kzm9g-reference: add AS3711 and CPUFreq DT bindings
ARM: shmobile: armadillo800eva: Reference DT implementation
ARM: shmobile: Remove unused r8a7790 GIC CPU interface DT bits
ARM: shmobile: Remove unused r8a73a4 GIC CPU interface DT bits
ARM: shmobile: r8a7740: Prepare for reference DT setup
ARM: shmobile: r8a7740: Add OF support to initialze the GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
mvebu dt changes for v3.11 (round 4)
- kirkwood
- reshuffle nodes from kirkwood.dtsi to -6281.dtsi, etc
- add i2c-gpio for km_kirkwood
- add cpu node so pending cpufreq driver will init
* tag 'dt-3.11-4' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood add cpus definition needed by cpufreq driver to dtsi
ARM: kirkwood: add i2c-gpio controller for km_kirkwood
ARM: kirkwood: refactor dtsi to largest common nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
A recent series has added CPU numbers to a lot of dts files,
but unfortunately in a few cases the #address-cells
and #size-cells values are missing, which causes build warnings.
This adds the missing ones for sunxi and sama5 that I found
through build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
ODROID-X board have a max77686 PMIC on i2c channel 0. The properties of used
LDO and BUCK are defined according the schematic.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
RTC is a basic feature of EXYNOS5440. But it was disabled
by issue that comes from EXYNOS5250. (commit id: 522ccdb6)
That issue only applies to EXYNOS5250 not EXYNOS5440. So,
there is no issue with enabled RTC on EXYNOS5440. This
change was tested on EXYNOS5440.
Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds clock provider information for DP controller required by CCF.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT node for DP controller to exynos5250 based Arndale Board
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
These nodes have separately been added to 4212 and 4412 dtsi
files by commit 30269ddff1 ("ARM: exynos: add missing properties
for combiner IRQs"). The existing node also contained a few
incorrect entries.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add max8997 regulator device node for exynos4210-origen board and list
all the supported regulators.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Added keypad node entries to Exynos4412 based Origen board DT file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Keypad pins/lines are board specific and should be added to respective
board dts files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding DWC3 device tree node for Exynos5250 needed to
parse device tree data.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding usb3.0 phy node for Exynos5250 along with the
necessary device data to be parsed.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pull ARM fixes from Russell King:
"The biggest two fixes are fixing a compilation error with the
decompressor, and a problem with our __my_cpu_offset implementation.
Other changes are very trivial and small, which seems to be the way
for most -rc stuff."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7747/1: pcpu: ensure __my_cpu_offset cannot be re-ordered across barrier()
ARM: 7750/1: update legacy CPU ID in decompressor cache support jump table
ARM: 7743/1: compressed/head.S: work around new binutils warning
ARM: 7742/1: topology: export cpu_topology
ARM: 7737/1: fix kernel decompressor compilation error with CONFIG_DEBUG_SEMIHOSTING
- Replace include linux/module.h with linux/export.h
- fix a checkpatch issue
- use of_platform_populate instead of of_platform_bus_probe
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0p6b
-----END PGP SIGNATURE-----
Merge tag 'sirf-arm-soc-v3.10-fixes' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into next/fixes-non-critical
From Barry Song, SiRF fixes for v3.10 (that we're punting to 3.11):
- Replace include linux/module.h with linux/export.h
- fix a checkpatch issue
- use of_platform_populate instead of of_platform_bus_probe
* tag 'sirf-arm-soc-v3.10-fixes' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
arm: prima2: use of_platform_populate instead of of_platform_bus_probe
ARM: prima2: fix a checkpatch issue
ARM: prima2: Replace include linux/module.h with linux/export.h
+ Linux 3.10-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
These properties are not needed so it's safe to remove them.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- One device tree fix for all spi node to have per clock added.
The clock is needed by spi driver to calculate bit rate divisor.
The spi node in the current device trees either does not have the
clock or is defined as dummy clock, in which case the driver probe
will fail or spi will run at a wrong bit rate.
- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRrLClAAoJEFBXWFqHsHzO7mIH/0zrRS+0aOdrrdL6pPWW+dua
b1q5xk7vU3LU57SN6WozsfoR5zWiO3qCK5R7wvT1eYFamDryUmlNsTiFz2XG8ZdK
qYVegCh86UqteSJYRBBYAuNcBjkKryPUP+Iy2PJuZKmrwNKhFfdoYYFh68th0Dc8
UcIv999Jm0JswfQ8Av4idSSMWtPwwyBm3dBEa3nI/pDdj2Wg9UmWXFml36wiEYyd
CUdlcY4UenBvPIAXq0UwH4vD65Bkuz7XQqjuLtP7rgwJmVdedXYOLv59Cka5FBR9
cZoeoKl9lm+7fJVfWwTtMiW1jmE+nOh/cmCZN9aE/T1xWu8dl29h6nCOXUFCbfI=
=sjAQ
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.10, take 2:
- One device tree fix for all spi node to have per clock added.
The clock is needed by spi driver to calculate bit rate divisor.
The spi node in the current device trees either does not have the
clock or is defined as dummy clock, in which case the driver probe
will fail or spi will run at a wrong bit rate.
- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.
* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: clk-imx6q: AXI clock select index is incorrect
ARM: dts: imx: fix clocks for cspi
ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRrO92AAoJEAKiPfwuf9N/LsgH/RjLx3DuFYA3WjMgBXyX/wyt
7FKq7qbCd10jNm67+yPOEwGDKcBq6tOVGUpsv95gj9vZA4/w5qsSXiHM5chREyca
T6qqUgUc6Q8raeqiLys6cyk2ivfZBW3fGd0uvj2RlnmEqWfvkuijta1tfp4aIPhv
2s2pMJcsLKeUTBx3/wtZeY2kGuY0Zs5JHGeXOSgpYwDuXYo/ymFeMQnHIgP2S+TO
xDgWDX6Sou9dHKiMZ6/ZGcBXTjD8iKDrBFs+N3gApfcNS/bhiZDZ1v6zWg6OIinB
tYjeDpISDto2wvCybGfEZMzNTyRc7l2mIIjlcJ/rVz3cc983P41bEXHXaeZYsqg=
=iXVY
-----END PGP SIGNATURE-----
Merge tag 'vt8500/dts-3.11' of git://github.com/linux-wmt/linux-vtwm into next/dt
From Tony Prisk, vt8500 devicetree updates for 3.11.
* tag 'vt8500/dts-3.11' of git://github.com/linux-wmt/linux-vtwm:
dts: vt8500: Correct reference clock on WM8850 SoCs
dts: vt8500: Add ARM, AHB, APB and DDR clock nodes to SoC files
dts: vt8500: Populate missing PLL nodes
dts: clk: vt8500: Update SoC dtsi to use WM8850 PLL clocks
dts: vt8500: Update serial nodes and disable by default in SoC files
dts: vt8500: Add devicetree support for WM8750 SoC and APC8750 board
dts: vt8500: Fix invalid/missing cpu nodes for soc files.
Signed-off-by: Olof Johansson <olof@lixom.net>
Highbank supports SGPIO by bit-banging out the SGPIO signals over
three GPIO pins defined in the DTB. Add support for this SGPIO
functionality.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.
This commit fixes those platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ranges DT entry needed by the PCIe controller is defined at the
SoC .dtsi level. However, some boards have a NOR flash, and to support
it, they need to override the SoC-level ranges property to add an
additional range. Since PCIe and NOR support came separately, some
boards were not properly changed to include the PCIe range in their
ranges property at the .dts level.
This commit fixes those platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous mask values for the legacy ARM CPU IDs were conflicting
with the CPU ID assignments for late-generation CPUs (like the
Qualcomm MSM/QSD or Broadcom Brahma-15 processors). This change
corrects the legacy ARM CPU ID value so that the jump table can
fall-through to the appropriate cache maintenance / MMU functions.
Signed-off-by: Marc C <marc.ceeeee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In August 2012, Matthew Gretton-Dann checked a change into binutils
labelled "Error on obsolete & warn on deprecated registers", apparently as
part of ARMv8 support. Apparently, this was supposed to emit the message
"Warning: This coprocessor register access is deprecated in ARMv8" when
using certain mcr/mrc instructions and building for ARMv8. Unfortunately,
the message that is actually emitted appears to be '(null)', which is
less helpful in comparison.
Even more unfortunately, this is biting us on every single kernel
build with a new gas, because arch/arm/boot/compressed/head.S and some
other files in that directory are built with -march=all since kernel
commit 80cec14a8 "[ARM] Add -march=all to assembly file build in
arch/arm/boot/compressed" back in v2.6.28.
This patch reverts Russell's nice solution and instead marks the head.S
file to be built for armv7-a, which fortunately lets us build all
instructions in that file without warnings even on the broken binutils.
Without this patch, building anything results in:
arch/arm/boot/compressed/head.S: Assembler messages:
arch/arm/boot/compressed/head.S:565: Warning: (null)
arch/arm/boot/compressed/head.S:676: Warning: (null)
arch/arm/boot/compressed/head.S:698: Warning: (null)
arch/arm/boot/compressed/head.S:722: Warning: (null)
arch/arm/boot/compressed/head.S:726: Warning: (null)
arch/arm/boot/compressed/head.S:957: Warning: (null)
arch/arm/boot/compressed/head.S:996: Warning: (null)
arch/arm/boot/compressed/head.S:997: Warning: (null)
arch/arm/boot/compressed/head.S:1027: Warning: (null)
arch/arm/boot/compressed/head.S:1035: Warning: (null)
arch/arm/boot/compressed/head.S:1046: Warning: (null)
arch/arm/boot/compressed/head.S:1060: Warning: (null)
arch/arm/boot/compressed/head.S:1092: Warning: (null)
arch/arm/boot/compressed/head.S:1094: Warning: (null)
arch/arm/boot/compressed/head.S:1095: Warning: (null)
arch/arm/boot/compressed/head.S:1102: Warning: (null)
arch/arm/boot/compressed/head.S:1134: Warning: (null)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org
Cc: Matthew Gretton-Dann <matthew.gretton-dann@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Selecting this option produces:
AS arch/arm/boot/compressed/debug.o
arch/arm/boot/compressed/debug.S:4:33: fatal error: mach/debug-macro.S: No such file or directory
compilation terminated.
make[3]: *** [arch/arm/boot/compressed/debug.o] Error 1
The semihosting support cannot be modelled into a senduart macro as
it requires memory space for argument passing. So the
CONFIG_DEBUG_LL_INCLUDE may not have any sensible value and the include
directive should be omitted.
While at it, let's add proper semihosting output support to the
decompressor.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Adding phy-mode to CPSW node for beaglebone, EVM and EVMsk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phy_id device tree data to am335x-evmsk device to bring up CPSW
ethernet present on am335x starter kit.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These aliases are used when feeding the DT from ATAGS to set the
devices MAC addresses.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This removes the "0x" prefix in front of the I2C DT device
address designation for each I2C DT node in the ux500
devicetree files.
Reported-by: Bryan Wu <cooloney@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As it stands, the memory node in the u8540 Device Tree is ignored and
memory is actually stipulated by the bootloader via ATAGS. ARM core
architecture code then extracts the memory ATAG and inserts it into the
Device Tree. In the u8540 the LittleKernel bootloader only stipulates
512MB of memory; however, the u8540 actually has 2GB. We're taking the
responsibility to register the remainder from Device Tree here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add regulator DT bindings for the ab8500-codec driver.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typo of VAMIC2 LDO regulator name in some DT-related files. This
patch replaces all occurrences with the right name.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix VAMIC1 LDO comment in DT files to be make it coherent with the
others.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After some discussion and deliberation we have decided to only use the
short form of the PRCMU register names i.e. not mention the peripheral
in which the registers reside.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds DT bindings for an AS3711 PMIC, used for supplying power to the
CPU, some peripherals and the backlight, as well as extends the cpu0 DT
node with OPPs and a reference to the PMIC to support the CPUFreq and
CPU DVFS functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Provide alternate board code for the Armadillo800EVA to demonstrate how
DT may be used given the current state of driver device tree support.
This is intended to act as a reference for mach-shmobile developers.
This a rather bare bone version with the following devices supported:
- GIC
- irqpins
- i2c0/1
- touchscreen
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove unused GIC CPU interface DT bits for r8a7790.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove unused GIC CPU interface DT bits for r8a73a4.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We need three steps to prepare for the new Armadillo reference DT board code:
- Split the device list into r8a7740_early_devices used by the old platform
data setup (board-armadillo.c) and r8a7740_devices_dt used by both
setup variants.
- Introduce new r8a7740_init_delay() to be more flexible about calling
shmobile_setup_delay().
- For the generic r8a7740 support, we switch to device tree setup for
the GIC, the irqpin devices and the I2C controllers.
This is slightly similar to commit 3b00f93426
"ARM: shmobile: sh73a0: Do not use early devices with DT reference"
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
WM8850 SoCs use a 24Mhz reference clock for the PLLs but the SoC file
currently parents all PLLs to the 25Mhz reference clock.
This patch corrects the PLL parent clock references.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
The Kirkwood CPU Freq driver needs a CPU definition in order for the probe
routine to activate it. Add a suitable definition to kirkwood.dtsi
This definition is only correct for single core SoCs. There is a dual core
SoC in the kirkwood family (88F632X) but the rest of the Kirkwood drivers in
the kernel don't currently support it. If they ever do the cpus definition
would need to be duplicated in each of the SoC specific include files.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
OMAP5 has 6 timers (GPTimers 5, 6, 8 to 11) that are capable of PWM.
The PWM capability property is missing from the node definitions of
couple of timers.
Add ti,timer-pwm attribute for timer 5, 6, 8 and 11.
Signed-off-by: Suman Anna <s-anna@ti.com>
[benoit.cousson@linaro.org: Update changelog and subject to highlight
the fix]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Earlier commits ensured proper muxing of pins related to proper
TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
OMAP4: TWL: mux sys_drm_msecure as output for PMIC).
However these only fixed legacy boot and not DT boot. For DT boot,
the default mux values need to be set properly in DT.
Special thanks to Nishanth Menon for the review and catching some
major flaws in earlier versions.
Tested on OMAP4430/Panda and OMAP4460/Panda-ES.
Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[benoit.cousson@linaro.org: Slightly change the subject to align
board name with file name]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The gpmc driver is actually looking for "gpmc,num-cs" and
"gpmc,num-waitpins" properties in DT. The binding doc also states
this.
Correct the properties in the dts to provide the right values for the
gpmc driver.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Stephen Warren reported the recent commit 78506f2 (add support for
extended FIFO-size of PL011-r1p5) breaks the serial port on the
BCM2835 ARM SoC.
A UART compatible with the ARM PL011-r1p5 should have 32-deep FIFOs.
The BCM2835 UART just looks like an ARM PL011-r1p5, but has 16-deep
FIFOs just like PL011-r1p4 or earlier revisions. As a workaround for
this compatibility issue, this patch overrides the HW UART periphid
register values with the actually compatible UART periphid 0x00241011
(r1p3 or r1p4).
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRqRD8AAoJEAf03oE53VmQDXsIAI9uZ9Lrf3Hi5srFxMeDnJxD
LysPAz0BW+8XSC5CHCWhu8JxLtUnZy4y4yice/y2Uol0rzqb8gR40DRym/mHJF6t
zGRitG553zYe53rVGjOBX/e2sY+vhhm2slOdpxH5aB8ZES3WJxKYddqdvHhcwW3J
gzBP1S10mwspEuA7vQ+1r9k4WoGis7WVK1HLghga1yb4C/B5yFNhujZz3wweIIaw
eep55SDPiJhtVzlLOZOsVh3TZuSStyElfJTPk+UkFnz2QU1D7mJri55rPT121iGN
Vfc4NDAOyirOGTbSzY2cKSB53To8fipHRL0NzICCifkMuVzA2RWl13jOL/jo9QU=
=6Cw/
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Big DT-centric update for AT91:
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/dt: add pinctrl definition for at91 tc blocks
ARM: at91/dts: add the watchdog nodes for at91 boards
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
ARM: at91: drop non DT: Calao USB-A96x
ARM: at91: dt: add Calao USB-A9G20 low power version
ARM: at91: dt: usb-a9263: add dataflash support
ARM: at91: dt: usb-a9263: update shutdown controller
ARM: at91: dt: usb-a9260: update shutdown controller
ARM: at91: dt: sam9260: add i2c gpio pinctrl
ARM: at91: switch Fox G20 board .dts to pre-processor defines
ARM: at91: add Acme Systems Fox G20 board
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
ARM: at91/at91-ariag25.dts: add RTC node
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpP1WAAoJEAi3KVZQDZAeItIH/1QVHhqYSpOnXGu4zQHswvIM
SRQoy4hiCJm+yywTnIDJPMQdBKD1vURRRdGWQouNsFoBaHki4v2BBxfBNFoDN+rx
VtECH7F1SbJ/Pb7XLVnswqRXVNqrY5fOY5mW42ALFBT9VxcKoD1FyqCaXfaU9JA4
VQCzR7DjFhr8bppZknQ5ZT/qI66Wj1oNiJtBdItmxT0pVfElvAOV6FHzfMGrrDrM
+v8T8KdFIdmH1Ny5J5KLQSE9qBLqae0vlDNgsfwfh1DY/Lye3rDHqPDKrh7YZjHR
xNc6JU+zEdP3tK1f1jgmjn/giY7HqpAFm46p9k/pF9gsE5SE0L/e0Dh9apOcq24=
=qUyf
-----END PGP SIGNATURE-----
Merge tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux into next/soc
From Jason Cooper:
mvebu pcie driver (kirkwood) for v3.11
- kirkwood
- enable pcie driver
- migrate boards over to pcie dt init
depends
- mvebu/pcie
- mvebu/of_pci
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'pcie_kw-3.11' of git://git.infradead.org/users/jcooper/linux:
arm: kirkwood: convert db-88f6281/db-88f6282 to the Device Tree
arm: kirkwood: convert QNAP TS219 to use DT for the PCIe interface
arm: kirkwood: convert ZyXEL NSA310 to use DT for the PCIe interface
arm: kirkwood: convert MPL CEC4 to use DT for the PCIe interface
arm: kirkwood: convert Iomega Iconnect to use DT for the PCIe interface
arm: kirkwood: add SoC-level Device Tree data for PCIe interfaces
arm: kirkwood: move PCIe window init to legacy driver
pci: mvebu: enable driver usage on Kirkwood
- mvebu
- enable two usb interfaces on Armada XP-GP
- kirkwood
- move pinmux configs to their individual devices
- group the pinmux configs on OpenBlocks A6
- add the Init button for the OpenBlocks A6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPZAAAoJEAi3KVZQDZAe/6AIAIvtbKlec9up7/QoIzM7varY
Qfb7OU6EQYnNmTiY+n/y2REz03mUC/cnrvRZ0YD31i5WwHZWGQiz1R692Tt1e07A
Cugl75yLuOFnsSKqkvRy0Km2QF35Irk22stBRP85csGu/LjjSqr0gXDsJ2++oQfZ
ssco7I5MsTEFJDpeVAB5jFaFm+hs+uM8/WsUf7l7qjyImqkz1WZPZfkgevWm3UjH
Mz2Ur2Sbapq5gU+/h8GdzWJdCuSM0wmZ3TKGOk2BCbMFBFSr72tPUgVDwYge7Ae4
5lPoeHg00o8TM6kpf5OBGW8kq6oMij33e7YjVpAp/YdsAmyua1gFCFikW3APuJU=
=SWgl
-----END PGP SIGNATURE-----
Merge tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux into next/dt
From jason Cooper, mvebu dt changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux: (27 commits)
arm: kirkwood: openblocks-a6: add support for Init button
arm: kirkwood: openblocks-a6: group pinmux configurations
arm: kirkwood: ts219: move pinmux configs to the right devices
arm: kirkwood: topkick: move pinmux configs to the right devices
arm: kirkwood: openblocks_a6: move pinmux configs to the right devices
arm: kirkwood: nsa310: move pinmux configs to the right devices
arm: kirkwood: readynas: move pinmux configs to the right devices
arm: kirkwood: mplcec4: move pinmux configs to the right devices
arm: kirkwood: buffalo linkstation: move pinmux configs to the right devices
arm: kirkwood: keymile: move pinmux configs to the right devices
arm: kirkwood: ns2: move pinmux configs to the right devices
arm: kirkwood: iomega ix2-200: move pinmux configs to the right devices
arm: kirkwood: iconnect: move pinmux configs to the right devices
arm: kirkwood: iconnect: give meaningful names to pinmux configs
arm: kirkwood: ib62x0: move pinmux configs to the right devices
arm: kirkwood: guruplug: move pinmux configs to the right devices
arm: kirkwood: goflexnet: move pinmux configs to the right devices
arm: kirkwood: dreamplug: move pinmux configs to the right devices
arm: kirkwood: dockstar: move pinmux configs to the right devices
arm: kirkwood: dlink dns: move pinmux configs to the right devices
...
- kirkwood
- QNAP use power-off driver
- LSXL use restart-poweroff driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRpPUAAAoJEAi3KVZQDZAe1QYIAKjPpNdRsGCW6LM1qKBssDHQ
l6xYFF2y2jy/ICOgMZIWp7GAvBxnC5t35gA2niRwCYFI4bqplJ01sZ4JAQ5MIUxz
roqJta8GUYtA6dvZfr+9kfEk3TWyyUHKF1sdkg8XRm2vCPq2exXb4fz4FBhqKEia
YpRonLiM/IChHb85y/pHZ6uPuGT2OnAvvTVvZPJJFvbMKGSrKf5mP5IvZ8roBJbA
7diGav9K7xQmgAM/D2z+7O7LLizFSaZhDFsp4s/dJ+sNLB3iSBZ1TnmeAGIkEf/w
fcrazF6mek5LB3GSoqzE+kUJKFP0z4a/lMpqlehHQyRZ1EAv5YA86GNBZgniAfY=
=xYiL
-----END PGP SIGNATURE-----
Merge tag 'boards-3.11-2' of git://git.infradead.org/users/jcooper/linux into next/boards
From Jason Cooper, mvebu board changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'boards-3.11-2' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Convert LSXL to restart-poweroff driver.
ARM: Kirkwood: Make use of the QNAP Power off driver.
ARM: Kirkwood: add DT support for Sheevaplug and Sheevaplug eSATA
The Hackberry has a PHY that needs to be powered up through a GPIO, so
we need to use a fixed regulator here.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC only has one pinset available for muxing, so hopefully, we
cover all cases.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds pinctrl configurations for at91 Timer Counter blocks.
These pin definitions can be referenced by "atmel,tcb-pwm" devices to
setup pins as PWM output for instance.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: switch to pinctrl pre-processor macros]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91sam9x5, at91sam9n12
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some bad copy/paste got in as well as too many zeroes. Fix
everything up so that the registers after the @ sign are
consistent with the first reg property.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
the low power version have a mmc-spi
eanble mmc-spi and RV3029C2 RTC in at91_dt_defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
[nicolas.ferre@atmel.com: re-arranging nodes, removing nodes and some comments]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
UART0 is moved to generic at91sam9x5.dtsi file.
Both uarts are "disabled" as the corresponding pins on
Aria documentation are shown as GPIOs.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Due to a bug with RTC IMR, we cannot consider at91sam9x5 RTC compatible
with the previous one. Modify DT compatibility string, even if the driver
is not yet modified to take it into account.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
What GPIO pin is used with which device on the SSP/SPI bus
is as board-specific as it gets, so it does not belong here
in the core SoC file, and it is disabled so it doesn't hurt
to delete this.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches to including <dt-bindings/interrupt-controller/irq.h>
and referencing the apropriate flags from there instead of
open-coding the flag numerals everywhere in the ux500 device
trees.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Tegra USB bindings were in bad shape. The patches in this branch
fix the binding definitions, and make all the necessary additions to
the DT files. Stale nodes/properties will be removed early in 3.12
once the USB driver has been updated for the new binding.
These changes are needed in both the USB tree, to allow the driver to
be updated to handle them, and the Tegra tree, so that various tree-
wide DT changes (e.g. conversion of IRQ/GPIO/clock constants to defines)
can be applied on top of them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fg0r
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.11-deps-for-usb' into next
ARM: tegra: DT-related fixes needed by the USB tree
The Tegra USB bindings were in bad shape. The patches in this branch
fix the binding definitions, and make all the necessary additions to
the DT files. Stale nodes/properties will be removed early in 3.12
once the USB driver has been updated for the new binding.
These changes are needed in both the USB tree, to allow the driver to
be updated to handle them, and the Tegra tree, so that various tree-
wide DT changes (e.g. conversion of IRQ/GPIO/clock constants to defines)
can be applied on top of them.
* tag 'tegra-for-3.11-deps-for-usb':
ARM: tegra: update device trees for USB binding rework
ARM: tegra: modify ULPI reset GPIO properties
ARM: tegra: finalize USB EHCI and PHY bindings
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch prepares the use of '#define' into dts files.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that the mvebu-pcie driver is in place and enabled for kirkwood,
convert to initializing PCIe via devicetree.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Use the Tegra114 CAR binding header (tegra114-car.h) to replace magic
numbers in the device tree. For example,
- clocks = <&tegra_car 28>;
+ clocks = <&tegra_car CLK_HOST1X>;
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, updated since tegra20-car.h moved for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use the Tegra30 CAR binding header (tegra30-car.h) to replace magic
numbers in the device tree. For example,
- clocks = <&tegra_car 28>;
+ clocks = <&tegra_car CLK_HOST1X>;
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, updated since tegra30-car.h moved for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use the Tegra20 CAR binding header (tegra20-car.h) to replace magic
numbers in the device tree. For example,
- clocks = <&tegra_car 28>;
+ clocks = <&tegra_car CLK_HOST1X>;
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[swarren, updated since tegra20-car.h moved for consistency]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The charger is now represented by a distinct subnode of the tps65090
device. Add this node and enable low current charging with it.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use TEGRA_GPIO() macro to name all GPIOs referenced by GPIO properties,
and some interrupts properties. Use standard GPIO flag defines too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Replace /include/ (dtc) with #include (C pre-processor) for all Tegra DT
files, so that gcc -E handles the entire include tree, and hence any of
those files can #include some other file e.g. for constant definitions.
This allows future use of #defines and header files in order to define
names for various constants, such as the IDs and flags in GPIO
specifiers. Use of those features will increase the readability of the
device tree files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add support for general-purpose LEDs present on Beaver
Signed-off-by: Eric Brower <ebrower@nvidia.com>
[swarren: put new node in correct sort order]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra30's boot ROM masks the top 1MiB of RAM. Fix the memory node in
Beaver's DT file to reflect this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
