We are seeing that some devices are raising the urgent bkops exception
events even when BKOPS status doesn't indicate performace impacted or
critical. Handle these device by determining their urgent bkops status
at runtime.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Query commands have 100ms timeout and it may timeout if they are
issued in parallel to ongoing read/write SCSI commands, this change
adds the retry (max: 10) in case command timeouts.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vendor's UFS device sends back to back NACs for the DL data frames
causing the host controller to raise the DFES error status. Sometimes
such UFS devices send back to back NAC without waiting for new
retransmitted DL frame from the host and in such cases it might be
possible the Host UniPro goes into bad state without raising the DFES
error interrupt. If this happens then all the pending commands would
timeout only after respective SW command (which is generally too
large).
This change workarounds such device behaviour like this:
- As soon as SW sees the DL NAC error, it would schedule the error
handler
- Error handler would sleep for 50ms to see if there any fatal errors
raised by UFS controller.
- If there are fatal errors then SW does normal error recovery.
- If there are no fatal errors then SW sends the NOP command to
device to check if link is alive.
- If NOP command times out, SW does normal error recovery
- If NOP command succeed, skip the error handling.
If DL NAC error is seen multiple times with some vendor's UFS devices
then enable this quirk to initiate quick error recovery and also
silence related error logs to reduce spamming of kernel logs.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
UFS driver's error handler forcefully tries to clear all the pending
requests. For each pending request in the queue, it waits 1 sec for it
to get cleared. If we have multiple requests in the queue then it's
possible that we might end up waiting for those many seconds before
resetting the host. But note that resetting host would any way clear
all the pending requests from the hardware. Hence this change skips
the forceful clear of the pending requests if we are anyway going to
reset the host (for fatal errors).
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices don't require VCCQ rail for device operations hence
this change adds support to recognize such devices and remove vote for
the unused VCCQ rail.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use the host quirks mechanism in order to
handle both device and host controller quirks.
In order to support various of UFS devices we should separate
handling the device quirks from the host controller's.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change adds support to read device descriptor and string descriptor
from a UFS device
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Sometimes due to hw issues it takes some time to the
host controller register to update. In order to verify the register
has updated, a polling is done until its value is set.
In addition the functions ufshcd_hba_stop() and
ufshcd_wait_for_register() was updated with an additional input
parameter, indicating the timeout between reads will
be done by sleeping or spinning the cpu.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition exists between request requeueing and scsi layer
error handling:
When UFS driver queuecommand returns a busy status for a request,
it will be requeued and its tag will be freed and set to -1.
At the same time it is possible that the request will timeout and
scsi layer will start error handling for it. The scsi layer reuses
the request and its tag to send error related commands to the device,
however its tag is no longer valid.
As this request was never really sent to the device, there is no
point to start error handling with the device.
Implement the scsi error handling timeout callback and bypass SCSI
error handling for request that were not actually sent to the device.
For such requests simply reset the block layer timer. Otherwise, let
SCSI layer perform the usual error handling.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When control reaches to Linux UFS driver during UFS boot mode, UFS host
controller interrupt status/enable registers may have left over
settings.
In order to avoid any spurious interrupts due to these left overs,
it's important to clear these interrupt status/enable registers before
enabling UFS interrupt handling.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Different platform may have different number of lanes
for the UFS link.
Add parameter to device tree specifying how many lanes
should be configured for the UFS link.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gilad Broner <gbroner@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
One of the strange things that the original sg driver did was let the
user provide both a data-out buffer (it followed the sg_header+cdb)
_and_ specify a reply length greater than zero. What happened was that
the user data-out buffer was copied into some kernel buffers and then
the mid level was told a read type operation would take place with the
data from the device overwriting the same kernel buffers. The user would
then read those kernel buffers back into the user space.
From what I can tell, the above action was broken by commit fad7f01e61
("sg: set dxferp to NULL for READ with the older SG interface") in 2008
and syzkaller found that out recently.
Make sure that a user space pointer is passed through when data follows
the sg_header structure and command. Fix the abnormal case when a
non-zero reply_len is also given.
Fixes: fad7f01e61
Cc: <stable@vger.kernel.org> #v2.6.28+
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 3209f9d780 ("scsi: storvsc: Fix a bug in the handling of SRB
status flags") filtered SRB_STATUS_AUTOSENSE_VALID out effectively making
the (SRB_STATUS_ABORTED | SRB_STATUS_AUTOSENSE_VALID) case a dead code. The
logic from this branch (e.g. storvsc_device_scan() call) is still required,
fix the check.
Cc: <stable@vger.kernel.org> #v4.4+
Fixes: 3209f9d780 ("scsi: storvsc: Fix a bug in the handling of SRB status flags")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In beiscsi_setup_boot_info(), the boot_kset pointer should be set to
NULL in case of failure otherwise an invalid pointer dereference may
occur later.
Cc: <stable@vger.kernel.org>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 397737223c ("sd: Make discard granularity match logical block
size when LBPRZ=1") accidentally set the granularity to one byte instead
of one logical block on devices that provide deterministic zeroes after
UNMAP.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Fixes: 397737223c
Cc: <stable@vger.kernel.org> #v4.4+
The test for the existence vpd_pg83 is inverted.
Fixes: 7e47976bcf ("scsi_sysfs: add 'is_bin_visible' callback")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Laurence Oberman loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are few MFI adapters which do not support MR_DCMD_PD_LIST_QUERY so
if MFI adapters fail this DCMD, it should not be considered as FATAL and
driver should not issue kill adapter and set per controller's instance
variable- pd_list_not_supported so that same variable can be used inside
functions- slave_alloc and slave_configure to allow firmware scan.
Killing adapter because of DCMD failure when this DCMD is not supported
causes driver's probe getting failed. This issue got introduced by
commit 6d40afbc7d ("megaraid_sas: MFI IO timeout handling").
Killing adapter in case of this DCMD failure should be limited to Fusion
adapters only. Per controller's instance variable allow_fw_scan is
removed as pd_list_not_supported better reflect the purpose.
Fixes: 6d40afbc7d
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling synchronize_irq() right before free_irq() is quite useless. On
one hand the IRQ can easily fire again before free_irq() is entered, on
the other hand free_irq() itself calls synchronize_irq() internally (in
a race condition free way), before any state associated with the IRQ is
freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With the current value of cmd_per_lun at 16, the throughput
over a single adapter is limited to around 150kIOPS.
Increase the value of cmd_per_lun to 256 to improve
throughput. With this change a single adapter is able to
attain close to the maximum throughput (380kIOPS).
Also change the number of RRQ entries that can be queued.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When switching to the internal LUN defined on the
IBM CXL flash adapter, there is an unnecessary
scan occurring on the second port. This scan leads
to the following extra lines in the log:
Dec 17 10:09:00 tul83p1 kernel: [ 3708.561134] cxlflash 0008:00:00.0: cxlflash_queuecommand: (scp=c0000000fc1f0f00) 11/1/0/0 cdb=(A0000000-00000000-10000000-00000000)
Dec 17 10:09:00 tul83p1 kernel: [ 3708.561147] process_cmd_err: cmd failed afu_rc=32 scsi_rc=0 fc_rc=0 afu_extra=0xE, scsi_extra=0x0, fc_extra=0x0
By definition, both of the internal LUNs are on the first port/channel.
When the lun_mode is switched to internal LUN the
same value for host->max_channel is retained. This
causes an unnecessary scan over the second port/channel.
This fix alters the host->max_channel to 0 (1 port), if internal
LUNs are configured and switches it back to 1 (2 ports) while
going back to external LUNs.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In order to support cxlflash in the PowerVM environment, underlying
hypervisor APIs have imposed a kernel API ordering change.
For the superpipe access to LUN, user applications need a context.
The cxlflash module creates this context by making a sequence of
cxl calls. In the current code, a context is initialized via
cxl_dev_context_init() followed by cxl_process_element(), a function
that obtains the process element id. Finally, cxl_start_work()
is called to attach the process element.
In the PowerVM environment, a process element id cannot be obtained
from the hypervisor until the process element is attached. The
cxlflash module is unable to create contexts without a valid
process element id.
To fix this problem, cxl_start_work() is called before obtaining
the process element id.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The cxlflash_disk_attach() routine currently uses a cascading error
gate strategy for its error cleanup path. While this strategy is
commonly used to handle cleanup scenarios, it is too restrictive when
function callouts need to be restructured. Problems range from
inserting error path bugs in previously 'good' code to the cleanup
path imposing design changes to how the normal path is structured.
A less restrictive approach is needed to support ordering changes
that come about when operating in different environments.
To overcome this restriction, the error cleanup path is modified to
have a single entrypoint and use conditional logic to cleanup where
necessary. Entities that require multiple cleanup steps must be
carefully vetted to ensure their APIs support state. In cases where
they do not (none as of this commit) additional local variables can
be used to maintain state on their behalf.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Presently, context information structures are allocated and
initialized in the same routine, create_context(). This imposes
an ordering restriction such that all pieces of information needed
to initialize a context must be known before the context is even
allocated.
This design point is not flexible when the order of context
creation needs to be modified. Specifically, this can lead to
problems when members of the context information structure are
a part of an ordering dependency (i.e. - the 'work' structure
embedded within the context).
To remedy, the allocation is left as-is, inside of the existing
create_context() routine and the initialization is transitioned
to a new void routine, init_context(). At the same time, in
anticipation of these routines not being called in sequence, a
state boolean is added to the context information structure to
track when the context has been initilized. The context teardown
routine, destroy_context(), is modified to support being called
with a non-initialized context.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When operating in the PowerVM environment, the cxlflash module can
receive an error from the hypervisor indicating that there are
existing mappings in the page table for the process MMIO space.
This issue exists because term_afu() currently invokes term_mc()
before stop_afu(), allowing for the master context to be detached
first and the problem state area to be unmapped second.
To resolve this issue, stop_afu() should be called before term_mc().
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The calls to pci_request_regions(), pci_resource_start(),
pci_set_dma_mask(), pci_set_master() and pci_save_state() are all
unnecessary for the IBM CXL flash adapter since data buffers
are not required to be mapped to the device's memory.
The use of services such as pci_set_dma_mask() are problematic on
hypervisor managed systems as the IBM CXL flash adapter is operating
under a virtual PCI Host Bridge (virtual PHB) which does not support
these services.
cxlflash 0001:00:00.0: init_pci: Failed to set PCI DMA mask rc=-5
The resolution is to simplify init_pci(), to a point where it does the
bare minimum (pci_enable_device). Similarly, remove the call the
pci_release_regions() from cxlflash_remove().
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
'device_add' will be evaluating the 'is_visible' callback when creating
the sysfs attributes. As by this time the device handler has not been
attached the 'access_state' attribute will never be visible.
This patch moves the code around so that the device handler is present
by the time 'is_visible' is evaluated to correctly display the
'access_state' attribute.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the 'access_state' field of the SCSI device whenever the path
state changes.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Track attached SCSI devices and update the 'access_state' whenever the
path state of the device changes.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Track attached SCSI devices and update the 'access_state' field whenever
an ALUA state change has been detected.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
scsi_proto.h now contains definitions for the ALUA state, so we don't
have to carry them in the device handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bart van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add an 'access_state' field to struct scsi_device and display them in
sysfs as 'access_state' and 'preferred_path' attribute.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Bart van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add 'is_bin_visible' callback to blank out unsupported vpd pages.
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The mvumi scsi hides the references to its suspend/resume functions in
an #ifdef but does not hide the implementation the same way:
drivers/scsi/mvumi.c:2632:12: error: 'mvumi_suspend' defined but not used [-Werror=unused-function]
drivers/scsi/mvumi.c:2651:12: error: 'mvumi_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations so the compiler knows it can
silently drop them instead of warning, while avoiding the addition of
another #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
tree: https://na01.safelinks.protection.outlook.com/?url=https%3a%2f%2fgit.kernel.org%2fpub%2fscm%2flinux%2fkernel%2fgit%2ftorvalds%2flinux.git&data=01%7c01%7ckys%40microsoft.com%7ce2e0622715844b79ad7108d32796ec3c%7c72f988bf86f141af91ab2d7cd011db47%7c1&sdata=ubr4GbBaNS%2ftOz%2buJBk0CL9N0UNG9x2TidLgy6Yovg4%3d master
head: 03c21cb775
commit: dac582417b storvsc: Properly support Fibre Channel devices
date: 3 weeks ago
config: x86_64-randconfig-s3-01281016 (attached as .config)
reproduce:
git checkout dac582417b
# save the attached .config to linux build tree
make ARCH=x86_64
All errors (new ones prefixed by >>):
drivers/built-in.o: In function `storvsc_remove':
>> storvsc_drv.c:(.text+0x213af7): undefined reference to `fc_remove_host'
drivers/built-in.o: In function `storvsc_drv_init':
>> storvsc_drv.c:(.init.text+0xcbcc): undefined reference to `fc_attach_transport'
>> storvsc_drv.c:(.init.text+0xcc06): undefined reference to `fc_release_transport'
drivers/built-in.o: In function `storvsc_drv_exit':
>> storvsc_drv.c:(.exit.text+0x123c): undefined reference to `fc_release_transport'
With this commit, the storvsc driver depends on FC atttributes. Make this
dependency explicit.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The snic version number is expected to be 4 decimals in the form like a
netmask string with each number stored in an element in array v.
However, there is an off-by-one check on the number of elements in v
allowing one to pass a 5 decimal version number causing v[4] to be
referenced, causing a buffer overrun. Fix the off-by-one error by
comparing to i > 3 rather than 4.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value of of_ioremap on failure should be -ENODEV and not
-1.
Found using Coccinelle. A simplified version of the semantic patch
used is:
//<smpl>
@@
expression *e;
@@
e = of_ioremap(...);
if (e == NULL) {
...
return
- -1
+ -ENODEV
;
}
//</smpl>
The single call site only checks that the return value is less than 0,
hence no change is required at the call site.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Shane Seymour <shane.seymour@hpe.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This bug causes the wrong command to have its sense pointer overwritten,
which sometimes leads to a NULL pointer deref. Fix this by checking which
command is being requeued before restoring the scsi_eh_save data.
It turns out that some targets will disconnect a REQUEST SENSE command.
The autosense algorithm doesn't anticipate this. Hence multiple commands
can end up undergoing autosense simultaneously, and they will all try to
use the same scsi_eh_save struct, which won't work. Defer autosense when
the scsi_eh_save storage is in use by another command.
Fixes: f27db8eb98 ("ncr5380: Fix autosense bugs")
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add missing checks for EH abort during arbitration and selection.
Rework the handling of NCR5380_select() result to improve clarity.
Fixes: 707d62b37f ("ncr5380: Fix EH during arbitration and selection")
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The list structures and related logic used in the NCR5380 driver mean that
a command cannot be queued twice (i.e. can't appear on more than one queue
and can't appear on the same queue more than once).
The abort handler must forget the command so that the mid-layer can re-use
it. E.g. the ML may send it back to the LLD via via scsi_eh_get_sense().
Fix this and also fix two error paths, so that commands get forgotten iff
completed.
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Calling NCR5380_select() from the abort handler causes various problems.
Firstly, it means potentially re-entering NCR5380_select(). Secondly, it
means that the lock is released, which permits the EH handlers to be
re-entered. The combination results in crashes. Don't do it.
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The calls to NCR5380_transfer_pio() for DATA IN and DATA OUT phases will
modify cmd->SCp.this_residual, cmd->SCp.ptr and cmd->SCp.buffer. That
works as long as EH does not intervene, which became possible in
atari_NCR5380.c when I changed the locking to bring it closer to
NCR5380.c.
If error recovery aborts the command, the scsi_cmnd in question and its
buffer will be returned to the mid-layer. So the transfer has to cease,
but it can't be stopped by the initiator because the target controls the
bus phase.
The problem does not arise if the lock is not released. That was fine for
atari_scsi, because it implements DMA. For the other drivers, we have to
release the lock and re-enable interrupts for long PIO data transfers.
The solution is to split the transfer into small chunks. In between chunks
the main loop releases the lock and re-enables interrupts. Thus interrupts
can be serviced and eh_bus_reset_handler can intervene if need be.
This fixes an oops in NCR5380_transfer_pio() that can happen when the EH
abort handler is invoked during DATA IN or DATA OUT phase.
Fixes: 11d2f63b9c ("ncr5380: Change instance->host_lock to hostdata->lock")
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commands subject to exception handling are to be returned to the scsi
mid-layer. Make sure that the various command pointers and command lists
in the low-level driver are correctly cleansed of affected commands.
This fixes some bugs that I accidentally introduced in v4.5-rc1 including
the removal of INIT_LIST_HEAD for the 'autosense' and 'disconnected'
command lists, and the possible NULL pointer dereference in
NCR5380_bus_reset() that was reported by Dan Carpenter.
hostdata->sensing may also point to an affected command so this pointer
also has to be cleared. The abort handler calls complete_cmd() to take
care of this; let's have the bus reset handler do the same.
The issue queue may also contain an affected command. If so, remove it.
This also follows the abort handler logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 62717f537e ("ncr5380: Implement new eh_bus_reset_handler")
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: <stable@vger.kernel.org> # 4.5
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This adds the missing error check and path for if the call to the
function hwi_init_controller fails as this error path was clearly missed
when writing beiscsi_eeh_resume and thus we must add it now in order to
be able to handle this nonrecoverable failing function call gracefully
in beiscsi_eeh_resume.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Do not reset fip selection time for every advertisement
in fcoe_ctlr_recv_adv() but set it only once for the first
validated FCF. Otherwise FCF selection won't happen when the
advertisements consistently arrive with sub FCOE_CTLR_START_DELAY
periodicity.
Tested-by: Narendra K <narendra_k@dell.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In high-datarate aging tests, it is found that the
SCSI framework can periodically issue lu resets as
some commands timeout.
Response TASK SET FULL and SAS_QUEUE_FULL may be
returned many times for the same command, causing the
timeouts.
The SAS_QUEUE_FULL errors come from
TRANS_TX_CREDIT_TIMEOUT_ERR, TRANS_TX_CLOSE_NORMAL_ERR,
and TRANS_TX_ERR_FRAME_TXED errors. They do not mean
that the queue is full in the host, but rather it is
equivalent to meaning the queue is full for the sdev.
To overcome this, the queue depth for the sdev is
reduced to 64 (from 256, set in sas_slave_configure()).
Normally error code SAS_QUEUE_FULL will result in the
sdev queue depth falling, but it falls too slowly during
high-datarate tests and commands timeout before it
has fallen to an adequete level from original value.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When TRANS_TX_ERR_FRAME_TXED error occurs in
a slot, the command should be re-attempted.
This error is equivalent to meaning that the queue
is full in the sdev (and not the host).
A superflous debug statement is also removed in the
slot complete handler.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When TRANS_TX_CREDIT_TIMEOUT_ERR or
TRANS_TX_CLOSE_NORMAL_ERR error occur in
a slot, the command should be re-attempted.
This error is equivalent to meaning that the queue
is full in the sdev (and not the host).
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a function to abort a slot (task) in the target
device and then cleanup and complete the task.
The function is called from work queue context as
it cannot be called from the context where it is
triggered (interrupt).
Flag hisi_sas_slot.abort is added as the flag used
in the slot error handler to indicate whether the
slot needs to be aborted in the sdev prior to
cleanup and finish.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>