This adds an increment of the link count when we add a new directory
entry, if that entry is itself a directory. This means that we no
longer need separate code to perform this operation.
Now that both adding and removing directory entries automatically
update the parent directory's link count if required, that makes
the code shorter and simpler than before.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
When we remove an entry from a directory, we can save ourselves
some trouble if we know the type of the entry in question, since
if it is itself a directory, we can update the link count of the
parent at the same time as removing the directory entry.
In addition this patch also merges the rmdir and unlink code which
was almost identical anyway. This eliminates the calls to remove
the . and .. directory entries on each rmdir (not needed since the
directory will be deallocated, anyway) which was the only thing preventing
passing the dentry to gfs2_dir_del(). The passing of the dentry
rather than just the name allows us to figure out the type of the entry
which is being removed, and thus adjust the link count when required.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
There are three users of gfs2_change_nlink which add to the link
count. Two of these are about to be removed in later patches, so
this means that there will no callers, when that happens allowing
removal of that function, also in a later patch.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: handle errors from coalesce_t2
cifs: refactor mid finding loop in cifs_demultiplex_thread
cifs: sanitize length checking in coalesce_t2 (try #3)
cifs: check for bytes_remaining going to zero in CIFS_SessSetup
cifs: change bleft in decode_unicode_ssetup back to signed type
Otherwise corrupted EFI partition tables can cause total confusion.
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously we marked all locks being promoted to a higher mode
with the try flag to avoid any potential deadlocks issues. The
DLM is able to detect these and report them in way that GFS2 can
deal with them correctly. So we can just request the required mode
and wait for a response without needing to perform this check.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
To avoid any possible races relating to the link count, we need to
recheck it under the inode's glock in all cases where it matters.
Also to ensure we never get any nasty surprises, this patch also
ensures that once the link count has hit zero it can never be
elevated by rereading in data from disk.
The only place we cannot provide a proper solution is in rename
in the case where we are removing a target inode and we discover
that the target inode has been already unlinked on another node.
The race window is very small, and we return EAGAIN in this case
to indicate what has happened. The proper solution would be to move
the lookup parts of rename from the vfs into library calls which
the fs could call directly, but that is potentially a very big job
and this fix should cover most cases for now.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: do not call __mark_dirty_inode under i_lock
libceph: fix ceph_osdc_alloc_request error checks
ceph: handle ceph_osdc_new_request failure in ceph_writepages_start
libceph: fix ceph_msg_new error path
ceph: use ihold() when i_lock is held
The __mark_dirty_inode helper now takes i_lock as of 250df6ed. Fix the
one ceph callers that held i_lock (__ceph_mark_dirty_caps) to return the
flags value so that the callers can do it outside of i_lock.
Signed-off-by: Sage Weil <sage@newdream.net>
In particular, s_freeing_list needs to be initialized early, since it is
used on some of the error paths when mounts fail. The mapping inode,
for example, would be initialized and then free'd on an error path
before s_freeing_list was initialized, but the inode drop operation
needs the s_freeing_list to be set up.
Normally you'd never see this, because not only is logfs fairly rare,
but a successful mount will never have any issues.
Reported-by: werner <w.landgraf@ru.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We should unlock the page and return -ENOMEM if ceph_osdc_new_request
failed.
Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com>
Signed-off-by: Sage Weil <sage@newdream.net>
If the buffer is dirty or pinned, then as well as printing a
warning, we should also refuse to release the page in
question.
Currently this can occur if there is a race between mmap()ed
writers and O_DIRECT on the same file. With the addition of
->launder_page() in the future, we should be able to close
this gap.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
In the recent patches to update the AIL list code, I managed to
forget that the ail list lock got dropped, even though I
added a comment specifically to remind myself :(
Reported-by: Barry Marson <bmarson@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The GFS2 fallocate code chooses a target size to for allocating chunks of
space. Whenever it can't find any resource groups with enough space free, it
halves its target. Since this target is in bytes, eventually it will no longer
be a multiple of blksize. As long as there is more space available in the
resource group than the target, this isn't a problem, since gfs2 will use the
actual space available, which is always a multiple of blksize. However,
when gfs couldn't fallocate a bigger chunk than the target, it was using the
non-blksize aligned number. This caused a BUG in later code that required
blksize aligned offsets. GFS2 now ensures that bytes is always a multiple of
blksize
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
cifs_demultiplex_thread calls coalesce_t2 to try and merge follow-on t2
responses into the original mid buffer. coalesce_t2 however can return
errors, but the caller doesn't handle that situation properly. Fix the
thread to treat such a case as it would a malformed packet. Mark the
mid as being malformed and issue the callback.
Cc: stable@kernel.org
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
...to reduce the extreme indentation. This should introduce no
behavioral changes.
Cc: stable@kernel.org
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Some applications must be aware of clock realtime being set
backward. A simple example is a clock applet which arms a timer for
the next minute display. If clock realtime is set backward then the
applet displays a stale time for the amount of time which the clock
was set backwards. Due to that applications poll the time because we
don't have an interface.
Extend the timerfd interface by adding a flag which puts the timer
onto a different internal realtime clock. All timers on this clock are
expired whenever the clock was set.
The timerfd core records the monotonic offset when the timer is
created. When the timer is armed, then the current offset is compared
to the previous recorded offset. When it has changed, then
timerfd_settime returns -ECANCELED. When a timer is read the offset is
compared and if it changed -ECANCELED returned to user space. Periodic
timers are not rearmed in the cancelation case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Chris Friesen <chris.friesen@genband.com>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Reviewed-by: Alexander Shishkin <virtuoso@slind.org>
Link: http://lkml.kernel.org/r/%3Calpine.LFD.2.02.1104271359580.3323%40ionos%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.infradead.org/ubifs-2.6:
UBIFS: seek journal heads to the latest bud in replay
UBIFS: do not free write-buffers when in R/O mode
This is the second fix of the following symptom:
UBIFS error (pid 34456): could not find an empty LEB
which sometimes happens after power cuts when we mount the file-system - UBIFS
refuses it with the above error message which comes from the
'ubifs_rcvry_gc_commit()' function. I can reproduce this using the integck test
with the UBIFS power cut emulation enabled.
Analysis of the problem.
Currently UBIFS replay seeks the journal heads to the last _replayed_ bud.
But the buds are replayed out-of-order, so the replay basically seeks journal
heads to the "random" bud belonging to this head, and not to the _last_ one.
The result of this is that the GC head may be seeked to a full LEB with no free
space, or very little free space. And 'ubifs_rcvry_gc_commit()' tries to find a
fully or mostly dirty LEB to match the current GC head (because we need to
garbage-collect that dirty LEB at one go, because we do not have @c->gc_lnum).
So 'ubifs_find_dirty_leb()' fails and we fall back to finding an empty LEB and
also fail. As a result - recovery fails and mounting fails.
This patch teaches the replay to initialize the GC heads exactly to the latest
buds, i.e. the buds which have the largest sequence number in corresponding
log reference nodes.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
Currently UBIFS has a small optimization - it frees write-buffers when it is
re-mounted from R/W mode to R/O mode. Of course, when it is mounted R/O, it
does not allocate write-buffers as well.
This optimization is nice but it leads to subtle problems and complications
in recovery, which I can reproduce using the integck test. The symptoms are
that after a power cut the file-system cannot be mounted if we first mount
it R/O, and then re-mount R/W - 'ubifs_rcvry_gc_commit()' prints:
UBIFS error (pid 34456): could not find an empty LEB
Analysis of the problem.
When mounting R/W, the reply process sets journal heads to buds [1], but
when mounting R/O - it does not do this, because the write-buffers are not
allocated. So 'ubifs_rcvry_gc_commit()' works completely differently for the
same file-system but for the following 2 cases:
1. mounting R/W after a power cut and recover
2. mounting R/O after a power cut, re-mounting R/W and run deferred recovery
In the former case, we have journal heads seeked to the a bud, in the latter
case, they are non-seeked (wbuf->lnum == -1). So in the latter case we do not
try to recover the GC LEB by garbage-collecting to the GC head, but we just
try to find an empty LEB, and there may be no empty LEBs, so we just fail.
On the other hand, in the former case (mount R/W), we are able to make a GC LEB
(@c->gc_lnum) by garbage-collecting.
Thus, let's remove this small nice optimization and always allocate
write-buffers. This should not make too big difference - we have only 3
of them, each of max. write unit size, which is usually 2KiB. So this is
about 6KiB of RAM for the typical case, and only when mounted R/O.
[1]: Note, currently the replay process is setting (seeking) the journal heads
to _some_ buds, not necessarily to the buds which had been the journal heads
before the power cut happened. This will be fixed separately.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
__blkdev_get() doesn't rescan partitions if disk->fops->open() fails,
which leads to ghost partition devices lingering after medimum removal
is known to both the kernel and userland. The behavior also creates a
subtle inconsistency where O_NONBLOCK open, which doesn't fail even if
there's no medium, clears the ghots partitions, which is exploited to
work around the problem from userland.
Fix it by updating __blkdev_get() to issue partition rescan after
-ENOMEDIA too.
This was reported in the following bz.
https://bugzilla.kernel.org/show_bug.cgi?id=13029
Stable: 2.6.38
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Zeuthen <zeuthen@gmail.com>
Reported-by: Martin Pitt <martin.pitt@ubuntu.com>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There are a couple of places in this code where these values can wrap or
go negative, and that could potentially end up overflowing the buffer.
Ensure that that doesn't happen. Do all of the length calculation and
checks first, and only perform the memcpy after they pass.
Also, increase some stack variables to 32 bits to ensure that they don't
wrap without being detected.
Finally, change the error codes to be a bit more descriptive of any
problems detected. -EINVAL isn't very accurate.
Cc: stable@kernel.org
Reported-and-Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
It's possible that when we go to decode the string area in the
SESSION_SETUP response, that bytes_remaining will be 0. Decrementing it at
that point will mean that it can go "negative" and wrap. Check for a
bytes_remaining value of 0, and don't try to decode the string area if
that's the case.
Cc: stable@kernel.org
Reported-and-Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The buffer length checks in this function depend on this value being a
signed data type, but 690c522fa converted it to an unsigned type.
Also, eliminate a problem with the null termination check in the same
function. cifs_strndup_from_ucs handles that situation correctly
already, and the existing check could potentially lead to a buffer
overrun since it increments bleft without checking to see whether it
falls off the end of the buffer.
Cc: stable@kernel.org
Reported-and-Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
nfs: don't lose MS_SYNCHRONOUS on remount of noac mount
NFS: Return meaningful status from decode_secinfo()
NFSv4: Ensure we request the ordinary fileid when doing readdirplus
NFSv4: Ensure that clientid and session establishment can time out
SUNRPC: Allow RPC calls to return ETIMEDOUT instead of EIO
NFSv4.1: Don't loop forever in nfs4_proc_create_session
NFSv4: Handle NFS4ERR_WRONGSEC outside of nfs4_handle_exception()
NFSv4.1: Don't update sequence number if rpc_task is not sent
NFSv4.1: Ensure state manager thread dies on last umount
SUNRPC: Fix the SUNRPC Kerberos V RPCSEC_GSS module dependencies
NFS: Use correct variable for page bounds checking
NFS: don't negotiate when user specifies sec flavor
NFS: Attempt mount with default sec flavor first
NFS: flav_array honors NFS_MAX_SECFLAVORS
NFS: Fix infinite loop in gss_create_upcall()
Don't mark_inode_dirty_sync() while holding lock
NFS: Get rid of pointless test in nfs_commit_done
NFS: Remove unused argument from nfs_find_best_sec()
NFS: Eliminate duplicate call to nfs_mark_request_dirty
NFS: Remove dead code from nfs_fs_mount()
Azurit reports large increases in system time after 2.6.36 when running
Apache. It was bisected down to a892e2d7dc ("vfs: use kmalloc()
to allocate fdmem if possible").
That patch caused the vfs to use kmalloc() for very large allocations and
this is causing excessive work (and presumably excessive reclaim) within
the page allocator.
Fix it by falling back to vmalloc() earlier - when the allocation attempt
would have been considered "costly" by reclaim.
Reported-by: azurIt <azurit@pobox.sk>
Tested-by: azurIt <azurit@pobox.sk>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Cc: Americo Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
XFS_IOC_ZERO_RANGE uses struct xfs_flock64, and thus requires argument
translation for 32-bit binaries on x86. Add the required
XFS_IOC_ZERO_RANGE_32 defined and add it to the list of commands that
require xfs_flock64 translation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
xfs_fsblock_t may be a 32-bit type on if XFS_BIG_BLKNOS is not set,
make sure to cast a value of this type to an unsigned long long
before using the ll printk qualifier.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
follow these guidelines:
- leave initialization in the declaration block if it fits the line
- move to the code where it's more suitable ('for' init block)
The last chunk was modified from David's original to be a correct
fix for what appeared to be a duplicate initialization.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Instead of finding the per-ag and then taking and releasing the pagb_lock
for every single busy extent completed sort the list of busy extents and
only switch betweens AGs where nessecary. This becomes especially important
with the online discard support which will hit this lock more often.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Update the extent tree in case we have to reuse a busy extent, so that it
always is kept uptodate. This is done by replacing the busy list searches
with a new xfs_alloc_busy_reuse helper, which updates the busy extent tree
in case of a reuse. This allows us to allow reusing metadata extents
unconditionally, and thus avoid log forces especially for allocation btree
blocks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Every time we reallocate a busy extent, we cause a synchronous log force
to occur to ensure the freeing transaction is on disk before we continue
and use the newly allocated extent. This is extremely sub-optimal as we
have to mark every transaction with blocks that get reused as synchronous.
Instead of searching the busy extent list after deciding on the extent to
allocate, check each candidate extent during the allocation decisions as
to whether they are in the busy list. If they are in the busy list, we
trim the busy range out of the extent we have found and determine if that
trimmed range is still OK for allocation. In many cases, this check can
be incorporated into the allocation extent alignment code which already
does trimming of the found extent before determining if it is a valid
candidate for allocation.
Based on earlier patches from Dave Chinner.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
While we need to make sure we do not reuse busy extents, there is no need
to force out busy extents when moving them between the AGFL and the
freespace btree as we still take care of that when doing the real allocation.
To avoid the log force when just moving extents from the different free
space tracking structures, move the busy search out of
xfs_alloc_get_freelist into the callers that need it, and move the busy
list insert from xfs_free_ag_extent which is used both by AGFL refills
and real allocation to xfs_free_extent, which is only used by the latter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
On a remount, the VFS layer will clear the MS_SYNCHRONOUS bit on the
assumption that the flags on the mount syscall will have it set if the
remounted fs is supposed to keep it.
In the case of "noac" though, MS_SYNCHRONOUS is implied. A remount of
such a mount will lose the MS_SYNCHRONOUS flag since "sync" isn't part
of the mount options.
Reported-by: Max Matveev <makc@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When compiling, I was getting this warning:
fs/nfs/nfs4xdr.c: In function ‘decode_secinfo’:
fs/nfs/nfs4xdr.c:4839:6: warning: variable ‘status’ set but not used
[-Wunused-but-set-variable]
We were unconditionally returning 0 as long as there wasn't an error
coming out of xdr_inline_decode(). We probably want to check the error
status coming out of decode_op_hdr() and decode_secinfo_gss(), rather
than assuming that everything is OK all the time.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When readdir() returns a directory entry for the root of a mounted
filesystem, Linux follows the old convention of returning the inode
number of the covered directory (despite newer versions of POSIX declaring
that this is a bug).
To ensure this continues to work, the NFSv4 readdir implementation requests
the 'mounted-on-fileid' from the server.
However, readdirplus also needs to instantiate an inode for this entry, and
for that, we also need to request the real fileid as per this patch.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: cleanup error handling in inode.c
Btrfs: put the right bio if we have an error
Btrfs: free bitmaps properly when evicting the cache
Btrfs: Free free_space item properly in btrfs_trim_block_group()
btrfs: add missing spin_unlock to a rare exit path
Btrfs: check return value of kmalloc()
btrfs: fix wrong allocating flag when reading page
Btrfs: fix missing mutex_unlock in btrfs_del_dir_entries_in_log()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
eCryptfs: Flush dirty pages in setattr
eCryptfs: Handle failed metadata read in lookup
eCryptfs: Add reference counting to lower files
eCryptfs: dput dentries returned from dget_parent
eCryptfs: Remove extra d_delete in ecryptfs_rmdir
Now that the whole dcache_hash_bucket crap is gone, go all the way and
also remove the weird locking layering violations for locking the hash
buckets. Add hlist_bl_lock/unlock helpers to move the locking into the
list abstraction instead of requiring each caller to open code it.
After all allowing for the bit locks is the whole point of these helpers
over the plain hlist variant.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After 57db4e8d73 changed eCryptfs to
write-back caching, eCryptfs page writeback updates the lower inode
times due to the use of vfs_write() on the lower file.
To preserve inode metadata changes, such as 'cp -p' does with
utimensat(), we need to flush all dirty pages early in
ecryptfs_setattr() so that the user-updated lower inode metadata isn't
clobbered later in writeback.
https://bugzilla.kernel.org/show_bug.cgi?id=33372
Reported-by: Rocko <rockorequin@hotmail.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
When failing to read the lower file's crypto metadata during a lookup,
eCryptfs must continue on without throwing an error. For example, there
may be a plaintext file in the lower mount point that the user wants to
delete through the eCryptfs mount.
If an error is encountered while reading the metadata in lookup(), the
eCryptfs inode's size could be incorrect. We must be sure to reread the
plaintext inode size from the metadata when performing an open() or
setattr(). The metadata is already being read in those paths, so this
adds minimal performance overhead.
This patch introduces a flag which will track whether or not the
plaintext inode size has been read so that an incorrect i_size can be
fixed in the open() or setattr() paths.
https://bugs.launchpad.net/bugs/509180
Cc: <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
The error processing of several places is changed like setting the
error number only at the error.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
In btrfs_submit_direct_hook if the first btrfs_map_block fails we need to put
the orig_bio, not bio.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
If our space cache is wrong, we do the right thing and free up everything that
we loaded, however we don't reset the total_bitmaps counter or the thresholds or
anything. So in btrfs_remove_free_space_cache make sure to call free_bitmap()
if it's a bitmap, this will keep us from panicing when we check to make sure we
don't have too many bitmaps. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Since commit dc89e98244, we've changed
to use a specific slab for alocation of free_space items.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The check on the return value of kmalloc() is added to some places.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
the space cache use extent_readpages() to read free space information,
so we can not use GFP_KERNEL flag to allocate memory, or it may lead
to deadlock.
Signed-off-by: Itaru Kitayama <kitayama@cl.bb4u.ne.jp>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
It is necessary to unlock mutex_lock before it return an error when
btrfs_alloc_path() fails.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
For any given lower inode, eCryptfs keeps only one lower file open and
multiplexes all eCryptfs file operations through that lower file. The
lower file was considered "persistent" and stayed open from the first
lookup through the lifetime of the inode.
This patch keeps the notion of a single, per-inode lower file, but adds
reference counting around the lower file so that it is closed when not
currently in use. If the reference count is at 0 when an operation (such
as open, create, etc.) needs to use the lower file, a new lower file is
opened. Since the file is no longer persistent, all references to the
term persistent file are changed to lower file.
Locking is added around the sections of code that opens the lower file
and assign the pointer in the inode info, as well as the code the fputs
the lower file when all eCryptfs users are done with it.
This patch is needed to fix issues, when mounted on top of the NFSv3
client, where the lower file is left silly renamed until the eCryptfs
inode is destroyed.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Call dput on the dentries previously returned by dget_parent() in
ecryptfs_rename(). This is needed for supported eCryptfs mounts on top
of the NFSv3 client.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
vfs_rmdir() already calls d_delete() on the lower dentry. That was being
duplicated in ecryptfs_rmdir() and caused a NULL pointer dereference
when NFSv3 was the lower filesystem.
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
No functional changes requires that we eat errors from strtobool.
If people want to not do this, then it should be fixed at a later date.
V2: Simplification suggested by Rusty Russell removes the need for
additional variable ret.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch ensures that we do not get permanently trapped in
the RPC layer when trying to establish a new client id or session.
This again ensures that the state manager can finish in a timely
fashion when the last filesystem to reference the nfs_client exits.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If a server for some reason keeps sending NFS4ERR_DELAY errors, we can end
up looping forever inside nfs4_proc_create_session, and so the usual
mechanisms for detecting if the nfs_client is dead don't work.
Fix this by ensuring that we loop inside the nfs4_state_manager thread
instead.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://git.infradead.org/ubifs-2.6:
UBIFS: fix master node recovery
UBIFS: fix false assertion warning in case of I/O failures
UBIFS: fix false space checking failure
The dentry hashing rules have been really quite complicated for a long
while, in odd ways. That made functions like __d_drop() very fragile
and non-obvious.
In particular, whether a dentry was hashed or not was indicated with an
explicit DCACHE_UNHASHED bit. That's despite the fact that the hash
abstraction that the dentries use actually have a 'is this entry hashed
or not' model (which is a simple test of the 'pprev' pointer).
The reason that was done is because we used the normal 'is this entry
unhashed' model to mark whether the dentry had _ever_ been hashed in the
dentry hash tables, and that logic goes back many years (commit
b3423415fb: "dcache: avoid RCU for never-hashed dentries").
That, in turn, meant that __d_drop had totally different unhashing logic
for the dentry hash table case and for the anonymous dcache case,
because in order to use the "is this dentry hashed" logic as a flag for
whether it had ever been on the RCU hash table, we had to unhash such a
dentry differently so that we'd never think that it wasn't 'unhashed'
and wouldn't be free'd correctly.
That's just insane. It made the logic really hard to follow, when there
were two different kinds of "unhashed" states, and one of them (the one
that used "list_bl_unhashed()") really had nothing at all to do with
being unhashed per se, but with a very subtle lifetime rule instead.
So turn all of it around, and make it logical.
Instead of having a DENTRY_UNHASHED bit in d_flags to indicate whether
the dentry is on the hash chains or not, use the hash chain unhashed
logic for that. Suddenly "d_unhashed()" just uses "list_bl_unhashed()",
and everything makes sense.
And for the lifetime rule, just use an explicit DENTRY_RCUACCEES bit.
If we ever insert the dentry into the dentry hash table so that it is
visible to RCU lookup, we mark it DENTRY_RCUACCESS to show that it now
needs the RCU lifetime rules. Now suddently that test at dentry free
time makes sense too.
And because unhashing now is sane and doesn't depend on where the dentry
got unhashed from (because the dentry hash chain details doesn't have
some subtle side effects), we can re-unify the __d_drop() logic and use
common code for the unhashing.
Also fix one more open-coded hash chain bit_spin_lock() that I missed in
the previous chain locking cleanup commit.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's a useless abstraction for 'hlist_bl_head', and it doesn't actually
help anything - quite the reverse. All the users end up having to know
about the hlist_bl_head details anyway, using 'struct hlist_bl_node *'
etc. So it just makes the code look confusing.
And the cost of it is extra '&b->head' syntactic noise, but more
importantly it spuriously makes the hash table dentry list look
different from the per-superblock DCACHE_DISCONNECTED dentry list.
As a result, the code ended up using ad-hoc locking for one case and
special helper functions for what is really another totally identical
case in the very same function.
Make it all look and work the same.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While password processing we can get out of options array bound if
the next character after array is delimiter. The patch adds a check
if we reach the end.
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
For some reason generic_setxattr() did not pass flags (XATTR_CREATE,
XATTR_REPLACE) to the filesystem specific helper. This caused that
setxattr(2) syscall just ignored these flags.
Fix the bug by passing flags correctly.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following symptoms:
1. Unmount UBIFS cleanly.
2. Start mounting UBIFS R/W and have a power cut immediately
3. Start mounting UBIFS R/O, this succeeds
4. Try to re-mount UBIFS R/W - this fails immediately or later on,
because UBIFS will write the master node to the flash area
which has been written before.
The analysis of the problem:
1. UBIFS is unmounted cleanly, both copies of the master node are clean.
2. UBIFS is being mounter R/W, starts changing master node copy 1, and
a power cut happens. The copy N1 becomes corrupted.
3. UBIFS is being mounted R/O. It notices the copy N1 is corrupted and
reads copy N2. Copy N2 is clean.
4. Because of R/O mode, UBIFS cannot recover copy 1.
5. The mount code (ubifs_mount()) sees that the master node is clean,
so it decides that no recovery is needed.
6. We are re-mounting R/W. UBIFS believes no recovery is needed and
starts updating the master node, but copy N1 is still corrupted
and was not recovered!
Fix this problem by marking the master node as dirty every time we
recover it and we are in R/O mode. This forces further recovery and
the UBIFS cleans-up the corruptions and recovers the copy N1 when
re-mounting R/W later.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: stable@kernel.org
When UBIFS switches to R/O mode because it detects I/O failures, then
when we unmount, we still may have allocated budget, and the assertions
which verify that we have not budget will fire. But it is expected to
have the budget in case of I/O failures, so the assertion warnings will
be false. Suppress them for the I/O failure case.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'for-2.6.39' of git://linux-nfs.org/~bfields/linux:
Open with O_CREAT flag set fails to open existing files on non writable directories
nfsd4: Fix filp leak
nfsd4: fix struct file leak on delegation
Commit 957935dc ("xfs: fix xfs_debug warnings" broke the logic in
__xfs_printk(). Instead of only printing one of two possible output
strings based on whether the fs has a name or not, it outputs both.
Fix it to only output one message again.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
This patch fixes UBIFS mount failure when the debugging support is enabled,
we are recovering from a power cut, we were first mounter R/O and we are
re-mounting R/W. In this case we should not assume that the amount of free
space before we have re-mounted R/W and after are equivalent, because
when we have mounted R/O the file-system is in a non-committed state so
the amount of free space is slightly smaller, due to the fact that we cannot
predict the amount of free space precisely before we commit.
This patch fixes the issue by skipping the debugging check in case of
recovery. This issue was reported by Caizhiyong <caizhiyong@huawei.com>
here: http://thread.gmane.org/gmane.linux.drivers.mtd/34350/focus=34387
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: Caizhiyong <caizhiyong@huawei.com>
Cc: stable@kernel.org [2.6.30+]
An open on a NFS4 share using the O_CREAT flag on an existing file for
which we have permissions to open but contained in a directory with no
write permissions will fail with EACCES.
A tcpdump shows that the client had set the open mode to UNCHECKED which
indicates that the file should be created if it doesn't exist and
encountering an existing flag is not an error. Since in this case the
file exists and can be opened by the user, the NFS server is wrong in
attempting to check create permissions on the parent directory.
The patch adds a conditional statement to check for create permissions
only if the file doesn't exist.
Signed-off-by: Sachin S. Prabhu <sprabhu@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch adds writeback_control to writing back the AIL
list. This means that we can then take advantage of the
information we get in ->write_inode() in order to set off
some pre-emptive writeback.
In addition, the AIL code is cleaned up a bit to make it
a bit simpler to understand.
There is still more which can usefully be done in this area,
but this is a good start at least.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The GLF_LRU flag introduced in the previous patch can be
used to check if a glock is on the lru list when a new
holder is queued and if so remove it, without having first
to get the lru_lock.
The main purpose of this patch however is to optimise the
glocks left over when an inode at end of life is being
evicted. Previously such glocks were left with the GLF_LFLUSH
flag set, so that when reclaimed, each one required a log flush.
This patch resets the GLF_LFLUSH flag when there is nothing
left to flush thus preventing later log flushes as glocks are
reused or demoted.
In order to do this, we need to keep track of the number of
revokes which are outstanding, and also to clear the GLF_LFLUSH
bit after a log commit when only revokes have been processed.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This adds support for two new flags. One keeps track of whether
the glock is on the LRU list or not. The other isn't really a
flag as such, but an indication of whether the glock has an
attached object or not. This indication is reported without
any locking, which is ok since we do not dereference the object
pointer but merely report whether it is NULL or not.
Also, this fixes one place where a tracepoint was missing, which
was at the point we remove deallocated blocks from the journal.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This patch is designed to clean up GFS2's fsync
implementation and ensure that it really does get everything on
disk. Since ->write_inode() has been updated, we can call that
via the vfs library function sync_inode_metadata() and the only
remaining thing that has to be done is to ensure that we get
any revoke records in the log after the inode has been written back.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Rather than allowing the glocks to be scheduled for possible
reclaim as soon as they have exited the journal, this patch
delays their entry to the list until the glocks in question
are no longer in use.
This means that we will rely on the vm for writeback of all
dirty data and metadata from now on. When glocks are added
to the lru list they should be freeable much faster since all
the I/O required to free them should have already been completed.
This should lead to much better I/O patterns under low memory
conditions.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
In order to ensure that the mapping stats (and thus the bdi) are correctly
updated, this patch changes the AIL writeback to use the filemap_datawrite
function. This helps prevent stalls in balance_dirty_pages() due to
large amounts of dirty metadata when there is little or no dirty data
around.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The GFS2 ->write_inode function should be more aggressive at writing
back to the filesystem. This adopts the XFS system of returning
-EAGAIN when the writeback has not been completely done. Also, we
now kick off in-place writeback when called with WB_SYNC_NONE,
but we only wait for it and flush the log when WB_SYNC_ALL is
requested.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The previous patches made function gfs2_dir_exhash_dealloc do nothing
but call function foreach_leaf. This patch simplifies the code by
moving the entire function foreach_leaf into gfs2_dir_exhash_dealloc.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Function foreach_leaf used to look up the leaf block address and get
a buffer_head. Then it would call leaf_dealloc which did the same
lookup. This patch combines the two operations by making foreach_leaf
pass the leaf bh to leaf_dealloc.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
At the end of function gfs2_dir_exhash_dealloc, it was setting the dinode
type to "file" to prevent directory corruption in case of a crash.
It was doing so in its own journal transaction. This patch makes the
change occur when the last call is make to leaf_dealloc, since it needs
to rewrite the directory dinode at that time anyway.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Since foreach_leaf is only called with leaf_dealloc as its only possible
call function, we can simplify the code by making it call leaf_dealloc
directly. This simplifies the code and eliminates the need for
leaf_call_t, the generic call method. This is a first small step in
simplifying the directory leaf deallocation code.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
On rare occasions we encounter gfs2 problems where an
invalid bitmap state transition is attempted. For example,
trying to "unlink" a free block. In these cases, there
is really no useful information logged to debug the problem.
This patch adds more debug details that should allow us to
more closely examine the problem and possibly solve it.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The Btrfs submit bio threads have a small number of
threads responsible for pushing down bios we've collected
for a large number of devices.
Since we do all the bios for a single device at once,
we want to make sure we unplug and send down the bios
for each device as we're done processing them.
The new plugging API removed the btrfs code to
unplug while processing bios, this adds it back with
the new API.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
23fcf2ec93 (nfsd4: fix oops on lock failure)
The above patch breaks free path for stp->st_file. If stp was inserted
into sop->so_stateids, we have to free stp->st_file refcount. Because
stp->st_file refcount itself is taken whether or not any refcounts are
taken on the stp->st_file->fi_fds[].
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: stable@kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: filesystem hang caused by incorrect lock order
GFS2: Don't try to deallocate unlinked inodes when mounted ro
GFS2: directly write blocks past i_size
GFS2: write_end error path fails to unlock transaction lock
I only want to try other secflavors during an initial mount if
NFS4ERR_WRONGSEC is returned. nfs4_handle_exception() could
potentially map other errors to EPERM, so we should handle this
error specially for correctness.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If we fail to contact the gss upcall program, then no message will
be sent to the server. The client still updated the sequence number,
however, and this lead to NFS4ERR_SEQ_MISMATCH for the next several
RPC calls.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (24 commits)
Btrfs: fix free space cache leak
Btrfs: avoid taking the chunk_mutex in do_chunk_alloc
Btrfs end_bio_extent_readpage should look for locked bits
Btrfs: don't force chunk allocation in find_free_extent
Btrfs: Check validity before setting an acl
Btrfs: Fix incorrect inode nlink in btrfs_link()
Btrfs: Check if btrfs_next_leaf() returns error in btrfs_real_readdir()
Btrfs: Check if btrfs_next_leaf() returns error in btrfs_listxattr()
Btrfs: make uncache_state unconditional
btrfs: using cached extent_state in set/unlock combinations
Btrfs: avoid taking the trans_mutex in btrfs_end_transaction
Btrfs: fix subvolume mount by name problem when default mount subvolume is set
fix user annotation in ioctl.c
Btrfs: check for duplicate iov_base's when doing dio reads
btrfs: properly handle overlapping areas in memmove_extent_buffer
Btrfs: fix memory leaks in btrfs_new_inode()
Btrfs: check for duplicate iov_base's when doing dio reads
Btrfs: reuse the extent_map we found when calling btrfs_get_extent
Btrfs: do not use async submit for small DIO io's
Btrfs: don't split dio bios if we don't have to
...
Rather than pass in some random truncated offset to the pid-related
functions, check that the offset is in range up-front.
This is just cleanup, the previous commit fixed the real problem.
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduced by acfdf5c383.
Cc: stable@kernel.org
Reported-by: Gerhard Heift <ml-nfs-linux-20110412-ef47@gheift.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This patch fixes a deadlock in GFS2 where two processes are trying
to reclaim an unlinked dinode:
One holds the inode glock and calls gfs2_lookup_by_inum trying to look
up the inode, which it can't, due to I_FREEING. The other has set
I_FREEING from vfs and is at the beginning of gfs2_delete_inode
waiting for the glock, which is held by the first. The solution is to
add a new non_block parameter to the gfs2_iget function that causes it
to return -ENOENT if the inode is being freed.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
This adds a couple of missing tests to avoid read-only nodes
from attempting to deallocate unlinked inodes.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reported-by: Michel Andre de la Porte <madelaporte@ubi.com>
GFS2 was relying on the writepage code to write out the zeroed data for
fallocate. However, with FALLOC_FL_KEEP_SIZE set, this may be past i_size.
If it is, it will be ignored. To work around this, gfs2 now calls
write_dirty_buffer directly on the buffer_heads when FALLOC_FL_KEEP_SIZE
is set, and it's writing past i_size.
This version is just a cleanup of my last version
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
I did an audit of gfs2's transaction glock for bugzilla bug
658619 and ran across this:
In function gfs2_write_end, in the unlikely event that
gfs2_meta_inode_buffer returns an error, the code may forget
to unlock the transaction lock because the "failed" label
appears after the call to function gfs2_trans_end.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
The free space caching code was recently reworked to
cache all the pages it needed instead of using find_get_page everywhere.
One loop was missed though, so it ended up leaking pages. This fixes
it to use our page array instead of find_get_page.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
While checking unregister_filesystem for saftey vs extra calls for
"ext4: register ext2 and ext3 alias after ext4" I realized that
the synchronize_rcu() was called on the error path but not on
the success path.
Cc: stable (2.6.38)
Signed-off-by: Milton Miller <miltonm@bga.com>
[ This probably won't really make a difference since commit d863b50ab0
("vfs: call rcu_barrier after ->kill_sb()"), but it's the right thing
to do. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Everytime we try to allocate disk space we try and see if we can pre-emptively
allocate a chunk, but in the common case we don't allocate anything, so there is
no sense in taking the chunk_mutex at all. So instead if we are allocating a
chunk, mark it in the space_info so we don't get two people trying to allocate
at the same time. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Reviewed-by: Liu Bo <liubo2009@cn.fujitsu.com>
A recent commit caches the extent state in end_bio_extent_readpage,
but the search it does should look for locked extents. This
fixes things to make it more effective.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
net/9p: nwname should be an unsigned int
9p: Fix sparse error
fs/9p: Fix error reported by coccicheck
9p: revert tsyncfs related changes
fs/9p: Use write_inode for data sync on server
fs/9p: Fix revalidate to return correct value
Currently, the state manager may continue to try recovering state forever
even after the last filesystem to reference that nfs_client has umounted.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
During RCU walk in path_lookupat and path_openat, the rcu lookup
frequently failed if looking up an absolute path, because when root
directory was looked up, seq number was not properly set in nameidata.
We dropped out of RCU walk in nameidata_drop_rcu due to mismatch in
directory entry's seq number. We reverted to slow path walk that need
to take references.
With the following patch, I saw a 50% increase in an exim mail server
benchmark throughput on a 4-socket Nehalem-EX system.
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: stable@kernel.org (v2.6.38)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we use write_inode to flush server
cache related to fid, we don't need tsyncfs either fort dotl or dotu
protocols. For dotu this helps to do a more efficient server flush.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
revalidate should return > 0 on success. Also return 0 on ENOENT
to force do_revalidate to return NULL dentry;
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
find_free_extent likes to allocate in contiguous clusters,
which makes writeback faster, especially on SSD storage. As
the FS fragments, these clusters become harder to find and we have
to decide between allocating a new chunk to make more clusters
or giving up on the cluster to allocate from the free space
we have.
Right now it creates too many chunks, and you can end up with
a whole FS that is mostly empty metadata chunks. This commit
changes the allocation code to be more strict and only
allocate new chunks when we've made good use of the chunks we
already have.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'linux-next' of git://git.infradead.org/ubifs-2.6:
UBIFS: fix compilation warnings when compiling with gcc 4.5
UBIFS: fix oops when R/O file-system is fsync'ed
The case we should be verifying when updating the dentry name is that
the _parent_ inode (the directory) semaphore is held, not the semaphore
for the dentry itself. It's the directory locking that rename and
readdir() etc all care about.
The comment just above even says so - but then the BUG_ON() still
checked the dentry inode itself.
Very few people noticed, because this helper function really isn't used
for very much, so you had to be using ncpfs to ever hit it.
I think I should just remove the BUG_ON (the function really has just
one user), but let's run with it fixed for a while before getting rid of
it entirely.
Reported-and-tested-by: Bongani Hlope <bonganih@bankservafrica.com>
Reported-and-tested-by: Bernd Feige <bernd.feige@uniklinik-freiburg.de>
Cc: Petr Vandrovec <petr@vandrovec.name>,
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On no-mmu arch, there is a memleak during shmem test. The cause of this
memleak is ramfs_nommu_expand_for_mapping() added page refcount to 2
which makes iput() can't free that pages.
The simple test file is like this:
int main(void)
{
int i;
key_t k = ftok("/etc", 42);
for ( i=0; i<100; ++i) {
int id = shmget(k, 10000, 0644|IPC_CREAT);
if (id == -1) {
printf("shmget error\n");
}
if(shmctl(id, IPC_RMID, NULL ) == -1) {
printf("shm rm error\n");
return -1;
}
}
printf("run ok...\n");
return 0;
}
And the result:
root:/> free
total used free shared buffers
Mem: 60320 17912 42408 0 0
-/+ buffers: 17912 42408
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 19096 41224 0 0
-/+ buffers: 19096 41224
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 20296 40024 0 0
-/+ buffers: 20296 40024
...
After this patch the test result is:(no memleak anymore)
root:/> free
total used free shared buffers
Mem: 60320 16668 43652 0 0
-/+ buffers: 16668 43652
root:/> shmem
run ok...
root:/> free
total used free shared buffers
Mem: 60320 16668 43652 0 0
-/+ buffers: 16668 43652
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
force_o_largefile() on ia64 is defined in <asm/fcntl.h> and requires
<linux/personality.h>.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
5520e89 ("brk: fix min_brk lower bound computation for COMPAT_BRK")
tried to get the whole logic of brk randomization for legacy
(libc5-based) applications finally right.
It turns out that the way to detect whether brk has actually been
randomized in the end or not introduced by that patch still doesn't work
for those binaries, as reported by Geert:
: /sbin/init from my old m68k ramdisk exists prematurely.
:
: Before the patch:
:
: | brk(0x80005c8e) = 0x80006000
:
: After the patch:
:
: | brk(0x80005c8e) = 0x80005c8e
:
: Old libc5 considers brk() to have failed if the return value is not
: identical to the requested value.
I don't like it, but currently see no better option than a bit flag in
task_struct to catch the CONFIG_COMPAT_BRK && randomize_va_space == 2
case.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel automatically evaluates partition tables of storage devices.
The code for evaluating LDM partitions (in fs/partitions/ldm.c) contains
a bug that causes a kernel oops on certain corrupted LDM partitions.
A kernel subsystem seems to crash, because, after the oops, the kernel no
longer recognizes newly connected storage devices.
The patch validates the value of vblk_size.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Richard Russon <rich@flatcap.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While decoding a secinfo reply, I store the list of supported sec
flavors on a page accessible through res->flavors. Before reading
each new flavor, I do some math to determine if there is enough
space left on this page, and I break out of my read look if there
isn't. In order to perform this check correctly, I need to use the
address of res->flavors, rather than the address of res.
When this loop was broken early I lied to the caller and told them
that the entire list had been decoded. This could lead to problems
if the caller tries to use any the garbage data claiming to be a
valid sec flavor. I fixed this by using res->flavors->num_flavors
as a counter, incrementing it every time a sec flavor is
successfully decoded.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We were always attempting sec flavor negotiation, even if the user
told us a specific sec flavor to use. If that sec flavor fails,
we should return an error rather than continuing with sec flavor
negotiation.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs4_lookup_root() is already configured to use either RPC_AUTH_UNIX
or a user specified flavor (through -o sec=<whatever>). We should
use this flavor first, and only attempt negotiation if it fails
with -EPERM.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFS_MAX_SECFLAVORS should already take into account RPC_AUTH_UNIX
and RPC_AUTH_NULL, so we don't need to set aside extra slots
for them.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There can be an infinite loop if gss_create_upcall() is called without
the userspace program running. To prevent this, we return -EACCES if
we notice that pipe_version hasn't changed (indicating that the pipe
has not been opened).
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
mark_inode_dirty_sync() grabs the same inode lock!
race conditions between holding the lock in pnfs_set_layoutcommit() and in
mark_inode_dirty_sync() can result in a second call to pnfs_layoutcommit_inode(), but
this will be a noop as NFS_INO_LAYOUTCOMMIT won't be set in the second call
Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
When compiling UBIFS with CONFIG_UBIFS_FS_DEBUG not set,
gcc-4.5.2 generates a slew of "warning: statement with no effect"
on references to non-void functions defined as 0.
To avoid these warnings, replace #defines with dummy inline functions.
Artem: massage the patch a bit, also remove the duplicate
'dbg_check_lprops()' prototype.
Signed-off-by: Maksim Rayskiy <maksim.rayskiy@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch fixes severe UBIFS bug: UBIFS oopses when we 'fsync()' an
file on R/O-mounter file-system. We (the UBIFS authors) incorrectly
thought that VFS would not propagate 'fsync()' down to the file-system
if it is read-only, but this is not the case.
It is easy to exploit this bug using the following simple perl script:
use strict;
use File::Sync qw(fsync sync);
die "File path is not specified" if not defined $ARGV[0];
my $path = $ARGV[0];
open FILE, "<", "$path" or die "Cannot open $path: $!";
fsync(\*FILE) or die "cannot fsync $path: $!";
close FILE or die "Cannot close $path: $!";
Thanks to Reuben Dowle <Reuben.Dowle@navico.com> for reporting about this
issue.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reported-by: Reuben Dowle <Reuben.Dowle@navico.com>
Cc: stable@kernel.org
Call posix_acl_valid() to check if an acl is valid or not.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Link count of the inode is not decreased if btrfs_set_inode_index()
fails.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Singed-off-by: Li Zefan <lizf@cn.fujitsu.com>
btrfs_next_leaf() can return -errno, and we should propagate
it to userspace.
This also simplifies how we walk the btree path.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
btrfs_next_leaf() can return -errno, and we should propagate
it to userspace.
This also simplifies how we walk the btree path.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
The extent_io code can take cached pointers into the extent state trees,
and these can make lookups much faster in common operations. The
caching only happens when specific bits are set that prevent merging
and splitting of the extent state.
A help function was added to uncache the state, and it was testing
the same set of conditionals. This can leak in very strange corner
cases where the lock bit goes away unexpectedly.
The uncaching should be unconditional. Once we have a ref on the
extent we should always give it up.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The inode was used in an earlier version of the code, but it isn't
used anymore.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In fs/nfs/super.c::nfs_fs_mount() we test for a NULL 'data':
...
if (data == NULL || mntfh == NULL)
goto out_free_fh;
...
and then further down in the function we test 'data' again:
...
nfs_fscache_get_super_cookie(
s, data ? data->fscache_uniq : NULL, NULL);
...
this second check is just dead code since there is no way 'data' could
possibly be NULL here.
We also rely on a non-NULL 'data' in more than one location between these
two tests, further proving the point that the second test is bogus.
This patch removes the dead code.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: don't allow mmap'ed pages to be dirtied while under writeback (try #3)
[CIFS] Warn on requesting default security (ntlm) on mount
[CIFS] cifs: clarify the meaning of tcpStatus == CifsGood
cifs: wrap received signature check in srv_mutex
cifs: clean up various nits in unicode routines (try #2)
cifs: clean up length checks in check2ndT2
cifs: set ra_pages in backing_dev_info
cifs: fix broken BCC check in is_valid_oplock_break
cifs: always do is_path_accessible check in cifs_mount
various endian fixes to cifs
Elminate sparse __CHECK_ENDIAN__ warnings on port conversion
Max share size is too small
Allow user names longer than 32 bytes
cifs: replace /proc/fs/cifs/Experimental with a module parm
cifs: check for private_data before trying to put it
nfs_scan_commit() is called with the inode->i_lock held, but it then
calls __mark_inode_dirty() while still holding the lock. This causes
a deadlock.
Push the inode->i_lock into nfs_scan_commit() so it can protect only
the parts of the code it needs to and can be dropped before the call
to __mark_inode_dirty() to avoid the deadlock.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Tested-by: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 93f1c20bc8.
It turns out that libmount misparses it because it adds a '-' character
in the uuid string, which libmount then incorrectly confuses with the
separator string (" - ") at the end of all the optional arguments.
Upstream libmount (in the util-linux tree) has been fixed, but until
that fix actually percolates up to users, we'd better not expose this
change in the kernel.
Let's revisit this later (possibly by exposing the UUID without any '-'
characters in it, avoiding the user-space bug).
Reported-by: Dave Jones <davej@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Karel Zak <kzak@redhat.com>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Cc: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is more or less the same patch as before, but with some merge
conflicts fixed up.
If a process has a dirty page mapped into its page tables, then it has
the ability to change it while the client is trying to write the data
out to the server. If that happens after the signature has been
calculated then that signature will then be wrong, and the server will
likely reset the TCP connection.
This patch adds a page_mkwrite handler for CIFS that simply takes the
page lock. Because the page lock is held over the life of writepage and
writepages, this prevents the page from becoming writeable until
the write call has completed.
With this, we can also remove the "sign_zero_copy" module option and
always inline the pages when writing.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
pathconf(, _PC_NAME_MAX) is too small for long Unicode filename on fat.
255 as max filename size on fat is Unicode UTF-16 characters.
it's not byte size.
https://bugzilla.kernel.org/show_bug.cgi?id=16469
To fix it, this returns "len * NLS_MAX_CHARSET_SIZE" instead.
Reported-by: Takumi Asaki <takumi.asaki@nokia.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Add fat_msg() to replace not cosequent used printk() in fs/fat/*
New message format should be as fallow:
FAT-fs (sda1): some thing happened.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
- convert fat_fs_error to use %pV
- be consequent and use "supor_block *sb" instead of "supor_block *s"
- use devise name in each message.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Warn once if default security (ntlm) requested. We will
update the default to the stronger security mechanism
(ntlmv2) in 2.6.41. Kerberos is also stronger than
ntlm, but more servers support ntlmv2 and ntlmv2
does not require an upcall, so ntlmv2 is a better
default.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
CC: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
When the TCP_Server_Info is first allocated and connected, tcpStatus ==
CifsGood means that the NEGOTIATE_PROTOCOL request has completed and the
socket is ready for other calls. cifs_reconnect however sets tcpStatus
to CifsGood as soon as the socket is reconnected and the optional
RFC1001 session setup is done. We have no clear way to tell the
difference between these two states, and we need to know this in order
to know whether we can send an echo or not.
Resolve this by adding a new statusEnum value -- CifsNeedNegotiate. When
the socket has been connected but has not yet had a NEGOTIATE_PROTOCOL
request done, set it to this value. Once the NEGOTIATE is done,
cifs_negotiate_protocol will set tcpStatus to CifsGood.
This also fixes and cleans the logic in cifs_reconnect and
cifs_reconnect_tcon. The old code checked for specific states when what
it really wants to know is whether the state has actually changed from
CifsNeedReconnect.
Reported-and-Tested-by: JG <jg@cms.ac>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
While testing my patchset to fix asynchronous writes, I hit a bunch
of signature problems when testing with signing on. The problem seems
to be that signature checks on receive can be running at the same
time as a process that is sending, or even that multiple receives can
be checking signatures at the same time, clobbering the same data
structures.
While we're at it, clean up the comments over cifs_calculate_signature
and add a note that the srv_mutex should be held when calling this
function.
This patch seems to fix the problems for me, but I'm not clear on
whether it's the best approach. If it is, then this should probably
go to stable too.
Cc: stable@kernel.org
Cc: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Minor revision to the original patch. Don't abuse the __le16 variable
on the stack by casting it to wchar_t and handing it off to char2uni.
Declare an actual wchar_t on the stack instead. This fixes a valid
sparse warning.
Fix the spelling of UNI_ASTERISK. Eliminate the unneeded len_remaining
variable in cifsConvertToUCS.
Also, as David Howells points out. We were better off making
cifsConvertToUCS *not* use put_unaligned_le16 since it means that we
can't optimize the mapped characters at compile time. Switch them
instead to use cpu_to_le16, and simply use put_unaligned to set them
in the string.
Reported-and-acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Thus spake David Howells:
The code that follows this:
remaining = total_data_size - data_in_this_rsp;
if (remaining == 0)
return 0;
else if (remaining < 0) {
generates better code if you drop the 'remaining' variable and compare
the values directly.
Clean it up per his recommendation...
Reported-and-acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Commit 522440ed made cifs set backing_dev_info on the mapping attached
to new inodes. This change caused a fairly significant read performance
regression, as cifs started doing page-sized reads exclusively.
By virtue of the fact that they're allocated as part of cifs_sb_info by
kzalloc, the ra_pages on cifs BDIs get set to 0, which prevents any
readahead. This forces the normal read codepaths to use readpage instead
of readpages causing a four-fold increase in the number of read calls
with the default rsize.
Fix it by setting ra_pages in the BDI to the same value as that in the
default_backing_dev_info.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=31662
Cc: stable@kernel.org
Reported-and-Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The BCC is still __le16 at this point, and in any case we need to
use the get_bcc_le macro to make sure we don't hit alignment
problems.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Currently, we skip doing the is_path_accessible check in cifs_mount if
there is no prefixpath. I have a report of at least one server however
that allows a TREE_CONNECT to a share that has a DFS referral at its
root. The reporter in this case was using a UNC that had no prefixpath,
so the is_path_accessible check was not triggered and the box later hit
a BUG() because we were chasing a DFS referral on the root dentry for
the mount.
This patch fixes this by removing the check for a zero-length
prefixpath. That should make the is_path_accessible check be done in
this situation and should allow the client to chase the DFS referral at
mount time instead.
Cc: stable@kernel.org
Reported-and-Tested-by: Yogesh Sharma <ysharma@cymer.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
make modules C=2 M=fs/cifs CF=-D__CHECK_ENDIAN__
Found for example:
CHECK fs/cifs/cifssmb.c
fs/cifs/cifssmb.c:728:22: warning: incorrect type in assignment (different base types)
fs/cifs/cifssmb.c:728:22: expected unsigned short [unsigned] [usertype] Tid
fs/cifs/cifssmb.c:728:22: got restricted __le16 [usertype] <noident>
fs/cifs/cifssmb.c:1883:45: warning: incorrect type in assignment (different base types)
fs/cifs/cifssmb.c:1883:45: expected long long [signed] [usertype] fl_start
fs/cifs/cifssmb.c:1883:45: got restricted __le64 [usertype] start
fs/cifs/cifssmb.c:1884:54: warning: restricted __le64 degrades to integer
fs/cifs/cifssmb.c:1885:58: warning: restricted __le64 degrades to integer
fs/cifs/cifssmb.c:1886:43: warning: incorrect type in assignment (different base types)
fs/cifs/cifssmb.c:1886:43: expected unsigned int [unsigned] fl_pid
fs/cifs/cifssmb.c:1886:43: got restricted __le32 [usertype] pid
In checking new smb2 code for missing endian conversions, I noticed
some endian errors had crept in over the last few releases into the
cifs code (symlink, ntlmssp, posix lock, and also a less problematic warning
in fscache). A followon patch will address a few smb2 endian
problems.
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Ports are __be16 not unsigned short int
Eliminates the remaining fixable endian warnings:
~/cifs-2.6$ make modules C=1 M=fs/cifs CF=-D__CHECK_ENDIAN__
CHECK fs/cifs/connect.c
fs/cifs/connect.c:2408:23: warning: incorrect type in assignment (different base types)
fs/cifs/connect.c:2408:23: expected unsigned short *sport
fs/cifs/connect.c:2408:23: got restricted __be16 *<noident>
fs/cifs/connect.c:2410:23: warning: incorrect type in assignment (different base types)
fs/cifs/connect.c:2410:23: expected unsigned short *sport
fs/cifs/connect.c:2410:23: got restricted __be16 *<noident>
fs/cifs/connect.c:2416:24: warning: incorrect type in assignment (different base types)
fs/cifs/connect.c:2416:24: expected unsigned short [unsigned] [short] <noident>
fs/cifs/connect.c:2416:24: got restricted __be16 [usertype] <noident>
fs/cifs/connect.c:2423:24: warning: incorrect type in assignment (different base types)
fs/cifs/connect.c:2423:24: expected unsigned short [unsigned] [short] <noident>
fs/cifs/connect.c:2423:24: got restricted __be16 [usertype] <noident>
fs/cifs/connect.c:2326:23: warning: incorrect type in assignment (different base types)
fs/cifs/connect.c:2326:23: expected unsigned short [unsigned] sport
fs/cifs/connect.c:2326:23: got restricted __be16 [usertype] sin6_port
fs/cifs/connect.c:2330:23: warning: incorrect type in assignment (different base types)
fs/cifs/connect.c:2330:23: expected unsigned short [unsigned] sport
fs/cifs/connect.c:2330:23: got restricted __be16 [usertype] sin_port
fs/cifs/connect.c:2394:22: warning: restricted __be16 degrades to integer
Signed-off-by: Steve French <sfrench@us.ibm.com>
In several places the sequence (set_extent_uptodate, unlock_extent) is used.
This leads to a duplicate lookup of the extent state. This patch lets
set_extent_uptodate return a cached extent_state which can be passed to
unlock_extent_cached.
The occurences of the above sequences are updated to use the cache. Only
end_bio_extent_readpage is updated that it first gets a cached state to
pass it to the readpage_end_io_hook as the prototype requested and is later
on being used for set/unlock.
Signed-off-by: Arne Jansen <sensille@gmx.net>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
I've been working on making our O_DIRECT latency not suck and I noticed we were
taking the trans_mutex in btrfs_end_transaction. So to do this we convert
num_writers and use_count to atomic_t's and just decrement them in
btrfs_end_transaction. Instead of deleting the transaction from the trans list
in put_transaction we do that in btrfs_commit_transaction() since that's the
only time it actually needs to be removed from the list. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We artificially limited the user name to 32 bytes, but modern servers handle
larger. Set the maximum length to a reasonable 256, and make the user name
string dynamically allocated rather than a fixed size in session structure.
Also clean up old checkpatch warning.
Signed-off-by: Steve French <sfrench@us.ibm.com>
This flag currently only affects whether we allow "zero-copy" writes
with signing enabled. Typically we map pages in the pagecache directly
into the write request. If signing is enabled however and the contents
of the page change after the signature is calculated but before the
write is sent then the signature will be wrong. Servers typically
respond to this by closing down the socket.
Still, this can provide a performance benefit so the "Experimental" flag
was overloaded to allow this. That's really not a good place for this
option however since it's not clear what that flag does.
Move that flag instead to a new module parameter that better describes
its purpose. That's also better since it can be set at module insertion
time by configuring modprobe.d.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
cifs_close doesn't check that the filp->private_data is non-NULL before
trying to put it. That can cause an oops in certain error conditions
that can occur on open or lookup before the private_data is set.
Reported-by: Ben Greear <greearb@candelatech.com>
CC: Stable <stable@kernel.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We create two subvolumes (meego_root and meego_home) in
btrfs root directory. And set meego_root as default mount
subvolume. After we remount btrfs, meego_root is mounted
to top directory by default. Then when we try to mount
meego_home (subvol=meego_home) to a subdirectory, it failed.
The problem is when default mount subvolume is set to
meego_root, we search meego_home in meego_root but can not find
it. So the solution is to add a new mount option (subvolrootid)
to specify subvol id of root and search subvol name in it. For
our case, now we can use "-o subvolrootid=0,subvol=meego_home)
to mount meego_home.
Detail information can be found in meego bugzilla:
https://bugs.meego.com/show_bug.cgi?id=15055
Signed-off-by: Zhong, Xin <xin.zhong@intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Apparently it is ok to submit a read to an IDE device with the same target page
for different offsets. This is what Windows does under qemu. The problem is
under DIO we expect them to be different buffers for checksumming reasons, and
so this sort of thing will result in checksum errors, when in reality the file
is fine. So when reading, check to make sure that all iov bases are different,
and if they aren't fall back to buffered mode, since that will work out right.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
This patch fixes memory leaks in btrfs_new_inode().
Signed-off-by: Yoshinori Sano <yoshinori.sano@gmail.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: use proper interfaces for on-stack plugging
xfs: fix xfs_debug warnings
xfs: fix variable set but not used warnings
xfs: convert log tail checking to a warning
xfs: catch bad block numbers freeing extents.
xfs: push the AIL from memory reclaim and periodic sync
xfs: clean up code layout in xfs_trans_ail.c
xfs: convert the xfsaild threads to a workqueue
xfs: introduce background inode reclaim work
xfs: convert ENOSPC inode flushing to use new syncd workqueue
xfs: introduce a xfssyncd workqueue
xfs: fix extent format buffer allocation size
xfs: fix unreferenced var error in xfs_buf.c
Also, applied patch from Tony Luck that fixes ia64:
xfs_destroy_workqueues() should not be tagged with__exit
in the branch before merging.
ia64 throws away .exit sections for the built-in CONFIG case, so routines
that are used in other circumstances should not be tagged as __exit.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix data corruption regression by reverting commit 6de9843dab
ext4: Allow indirect-block file to grow the file size to max file size
ext4: allow an active handle to be started when freezing
ext4: sync the directory inode in ext4_sync_parent()
ext4: init timer earlier to avoid a kernel panic in __save_error_info
jbd2: fix potential memory leak on transaction commit
ext4: fix a double free in ext4_register_li_request
ext4: fix credits computing for indirect mapped files
ext4: remove unnecessary [cm]time update of quota file
jbd2: move bdget out of critical section
Revert commit 6de9843dab, since it
caused a data corruption regression with BitTorrent downloads. Thanks
to Damien for discovering and bisecting to find the problem commit.
https://bugzilla.kernel.org/show_bug.cgi?id=32972
Reported-by: Damien Grassart <damien@grassart.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We can create 4402345721856 byte file with indirect block mapping.
However, if we grow an indirect-block file to the size with ftruncate(),
we can see an ext4 warning. The following patch fixes this problem.
How to reproduce:
# dd if=/dev/zero of=/mnt/mp1/hoge bs=1 count=0 seek=4402345721856
0+0 records in
0+0 records out
0 bytes (0 B) copied, 0.000221428 s, 0.0 kB/s
# tail -n 1 /var/log/messages
Nov 25 15:10:27 test kernel: EXT4-fs warning (device sda8): ext4_block_to_path:345: block 1074791436 > max in inode 12
Signed-off-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4_journal_start_sb() should not prevent an active handle from being
started due to s_frozen. Otherwise, deadlock is easy to happen, below
is a situation.
================================================
freeze | truncate
================================================
| ext4_ext_truncate()
freeze_super() | starts a handle
sets s_frozen |
| ext4_ext_truncate()
| holds i_data_sem
ext4_freeze() |
waits for updates |
| ext4_free_blocks()
| calls dquot_free_block()
|
| dquot_free_blocks()
| calls ext4_dirty_inode()
|
| ext4_dirty_inode()
| trys to start an active
| handle
|
| block due to s_frozen
================================================
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reported-by: Amir Goldstein <amir73il@users.sf.net>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
ext4 has taken the stance that, in the absence of a journal,
when an fsync/fdatasync of an inode is done, the parent
directory should be sync'ed if this inode entry is new.
ext4_sync_parent(), which implements this, does indeed sync
the dirent pages for parent directories, but it does not
sync the directory *inode*. This patch fixes this.
Also now return error status from ext4_sync_parent().
I tested this using a power fail test, which panics a
machine running a file server getting requests from a
client. Without this patch, on about every other test run,
the server is missing many, many files that had been synced.
With this patch, on > 6 runs, I see zero files being lost.
Google-Bug-Id: 4179519
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When the kernel does partition detection, on certain configurations with
external fibre channel raid systems (e.g. clariion from EMC) the read
would fail. And "ldm_validate_partition_table(): Disk read failed"
messages are printed to the console.
But the failure to read is not a critical error. Now since the message
is flagged as KERN_CRIT, it gets printed even when booting with the
"quiet" kernel parameter. Fix it by using KERN_INFO, as the failure to
read here is not really an error.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Reported-by : Klaus Hartmann <Klaus.Hartmann@ts.fujitsu.com>
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the appropriate members into struct user_arg_ptr and teach
get_user_arg_ptr() to handle is_compat = T case correctly.
This allows us to remove the compat_do_execve() code from fs/compat.c
and reimplement compat_do_execve() as the trivial wrapper on top of
do_execve_common(is_compat => true).
In fact, this fixes another (minor) bug. "compat_uptr_t str" can
overflow after "str += len" in compat_copy_strings() if a 64bit
application execs via sys32_execve().
Unexport acct_arg_size() and get_arg_page(), fs/compat.c doesn't
need them any longer.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
No functional changes, preparation.
Introduce struct user_arg_ptr, change do_execve() paths to use it
instead of "char __user * const __user *argv".
This makes the argv/envp arguments opaque, we are ready to handle the
compat case which needs argv pointing to compat_uptr_t.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Introduce get_user_arg_ptr() helper, convert count() and copy_strings()
to use it.
No functional changes, preparation. This helper is trivial, it just
reads the pointer from argv/envp user-space array.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Tested-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Change initial mount authflavor only when server returns NFS4ERR_WRONGSEC
NFS: Fix a signed vs. unsigned secinfo bug
Revert "net/sunrpc: Use static const char arrays"
Apparently it is ok to submit a read to an IDE device with the same target page
for different offsets. This is what Windows does under qemu. The problem is
under DIO we expect them to be different buffers for checksumming reasons, and
so this sort of thing will result in checksum errors, when in reality the file
is fine. So when reading, check to make sure that all iov bases are different,
and if they aren't fall back to buffered mode, since that will work out right.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
In btrfs_get_block_direct we call btrfs_get_extent to lookup the extent for the
range that we are looking for. If we don't find an extent, btrfs_get_extent
will insert a extent_map for that area and mark it as a hole. So it does the
job of allocating a new extent map and inserting it into the io tree. But if
we're creating a new extent we free it up and redo all of that work. So instead
pass the em to btrfs_new_extent_direct(), and if it will work just allocate the
disk space and set it up properly and bypass the freeing/allocating of a new
extent map and the expensive operation of inserting the thing into the io_tree.
Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
When looking at our DIO performance Chris said that for small IO's doing the
async submit stuff tends to be more overhead than it's worth. With this on top
of my other fixes I get about a 17-20% speedup doing a sequential dd with 4k
IO's. Basically if we don't have to split the bio for the map length it's small
enough to be directly submitted, otherwise go back to the async submit. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
We have been unconditionally allocating a new bio and re-adding all pages from
our original bio to the new bio. This is needed if our original bio is larger
than our stripe size, but if it is smaller than the stripe size then there is no
need to do this. So check the map length and if we are under that then go ahead
and submit the original bio. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
In the DIO code we often don't update the i_disk_size because the i_size isn't
updated until after the DIO is completed, so basically we are allocating a path,
doing a search, and updating the inode item for no reason since nothing changed.
btrfs_ordered_update_i_size will return 1 if it didn't update i_disk_size, so
only run btrfs_update_inode if btrfs_ordered_update_i_size returns 0. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Instead of calling kmap_atomic for every thing we set in the inode item, map the
entire inode item at the start and unmap it at the end. This makes a sequential
dd of 400mb O_DIRECT something like 1% faster. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
I saw a lockup where we kept getting into this start transaction->commit
transaction loop because of enospce. The fact is if we fail to make our
reservation, we've tried _everything_ several times, so we only need to try and
commit the transaction once, and if that doesn't work then we really are out of
space and need to just exit. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Currently we don't handle running out of space in the cache, so to fix this we
keep track of how far in the cache we are. Then we only dirty the pages if we
successfully modify all of them, otherwise if we have an error or run out of
space we can just drop them and not worry about the vm writing them out.
Thanks,
Tested-by Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: Josef Bacik <josef@redhat.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
quota: Don't write quota info in dquot_commit()
ext3: Fix writepage credits computation for ordered mode
Add proper blk_start_plug/blk_finish_plug pairs for the two places where
we issue buffer I/O, and remove the blk_flush_plug in xfs_buf_lock and
xfs_buf_iowait, given that context switches already flush the per-process
plugging lists.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
For a CONFIG_XFS_DEBUG=n build gcc complains about statements with no
effect in xfs_debug:
fs/xfs/quota/xfs_qm_syscalls.c: In function 'xfs_qm_scall_trunc_qfiles':
fs/xfs/quota/xfs_qm_syscalls.c:291:3: warning: statement with no effect
The reason for that is that the various new xfs message functions have a
return value which is never used, and in case of the non-debug build
xfs_debug the macro evaluates to a plain 0 which produces the above
warnings. This can be fixed by turning xfs_debug into an inline function
instead of a macro, but in addition to that I've also changed all the
message helpers to return void as we never use their return values.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
GCC 4.6 now warnings about variables set but not used. Fix the trivially
fixable warnings of this sort.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
On the Power platform, the log tail debug checks fire excessively
causing the system to panic early in testing. The debug checks are
known to be racy, though on x86_64 there is no evidence that they
trigger at all.
We want to keep the checks active on debug systems to alert us to
problems with log space accounting, but we need to reduce the impact
of a racy check on testing on the Power platform.
As a result, convert the ASSERT conditions to warnings, and
allow them to fire only once per filesystem mount. This will prevent
false positives from interfering with testing, whilst still
providing us with the indication that they may be a problem with log
space accounting should that occur.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
A fuzzed filesystem crashed a kernel when freeing an extent with a
block number beyond the end of the filesystem. Convert all the debug
asserts in xfs_free_extent() to active checks so that we catch bad
extents and return that the filesytsem is corrupted rather than
crashing.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
When we are short on memory, we want to expedite the cleaning of
dirty objects. Hence when we run short on memory, we need to kick
the AIL flushing into action to clean as many dirty objects as
quickly as possible. To implement this, sample the lsn of the log
item at the head of the AIL and use that as the push target for the
AIL flush.
Further, we keep items in the AIL that are dirty that are not
tracked any other way, so we can get objects sitting in the AIL that
don't get written back until the AIL is pushed. Hence to get the
filesystem to the idle state, we might need to push the AIL to flush
out any remaining dirty objects sitting in the AIL. This requires
the same push mechanism as the reclaim push.
This patch also renames xfs_trans_ail_tail() to xfs_ail_min_lsn() to
match the new xfs_ail_max_lsn() function introduced in this patch.
Similarly for xfs_trans_ail_push -> xfs_ail_push.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
This patch rearranges the location of functions in xfs_trans_ail.c
to remove the need for forward declarations of those functions in
preparation for adding new functions without the need for forward
declarations.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Similar to the xfssyncd, the per-filesystem xfsaild threads can be
converted to a global workqueue and run periodically by delayed
works. This makes sense for the AIL pushing because it uses
variable timeouts depending on the work that needs to be done.
By removing the xfsaild, we simplify the AIL pushing code and
remove the need to spread the code to implement the threading
and pushing across multiple files.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alex Elder <aelder@sgi.com>
