Support for m88rs2000 chip used in lmedm04 driver.
Note there are still lock problems.
Slow channel change due to the large block of registers sent in set_frontend.
Version 2 differences.
Front end is completely shut down when in sleep mode. This allow user to regain
control of device.
Kaffeine scan problem solved by removing register calls from get_frontend.
Kaffeine seems to call get_frontend when updating signal data. This can happen
in the middle of a tune stalling the driver.
Change calculations to those in the DS3000 driver.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These were in the original lme2510 device driver.
Removing them significantly speeds up the driver.
All tuners tested.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In CDRXD(), Negative number is assigned to unsigned variable
'state->noise_cal.tdCal2.
Members of 'SNoiseCal' should be 'signed short'.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DibAcquireLock() is implemented as mutex_lock_interruptible()
but the driver does not handle unsuccessful locking.
As a result it may lead to unlock of an unheld mutex.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several error paths, where &state->platform.risc.mem_mbx_lock
is not unlocked. The patch fixes it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
linux-next:
I like to spend some time reading code, in doing so I have found some
typos in some of the comments.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ryley and me tested several eLNA configuration values with both a rooftop
and a portable antenna.
Ryley fuond out that the best value for his Elgato stick is indeed the current
default value 0xC0.
Instead, my stick is not capable of tuning VHF channels with 0xC0. With 0x80,
VHF works but the tuner sensitivity with the portable antenna is poor.
Instead, the value 0xA0 works with VHF and also gives good performance with
both the rooftop and the portable antenna.
So we concluded that devices built on the reference design work best with 0xA0,
while custom designs (Elgato, PCTV) seem to require 0xC0.
I also removed the unused parameter "minor" in struct as102_dev_t.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Ryley Angus <rangus@student.unimelb.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes a regression in kernel 3.3 due to this patch:
http://patchwork.linuxtv.org/patch/8332/
That patch changes "#pragma pack(1)" with "__packed" attributes, but it is not
complete. In fact, in the as102 driver there are a lot of structs/unions
defined inside other structs/unions.
When the "__packed" attribute is applied only on the external struct, it will
not affect the internal struct definitions.
So the regression is fixed by specifiying the "__packed" attribute also on the
internal structs.
This patch should go into 3.3, as it fixes a regression introduced in the new
kernel version.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Ryley Angus <rangus@student.unimelb.edu.au>
Cc: stable@kernel.org # for v3.3
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add CI support to az6007 driver.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx231xx_v4l2_close() there are two calls to
cx231xx_release_resources(dev) followed by kfree(dev). That is a
problem since cx231xx_release_resources() already kfree()'s its
argument, so we end up doing a double free.
Easily resolved by just removing the redundant kfree() calls after the
calls to cx231xx_release_resources().
I also changed the 'dev = NULL' assignments (which are rather
pointless since 'dev' is about to go out of scope), to 'fh->dev = NULL'
since it looks to me that that is what was actually intended.
And I removed the 'dev = NULL' assignment at the end of
cx231xx_release_resources() since it is pointless.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current delay of 30uS is too short to recover any carrier.
In the lmedm04 driver delays were added to overcome carrier lock
problems. The typical delay was 30mS (2 x 15ms register write
0x2c and read 0x24).
Other drivers that use STV0288 don't appear to have any delay are
likely to have also suffered this problem.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no known problem here, but this is one of only two non-arch files
in the kernel which use asm/atomic.h instead of linux/atomic.h.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_DEF quirk. Add a corresponding entry in
the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Userptr can be very useful if a UVC camera is requested to use video
buffers allocated by another processing device. So that buffers don't
need to be copied.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support 32-bit/64-bit compatibility for the the UVCIOC_ ioctls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-EINVAL is the wrong error code in that case, replace it with -ENOTTY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers implementing custom ioctls need to handle 32-bit/64-bit
compatibility themselves. Provide them with a way to do so.
To avoid circular module dependencies, merge the v4l2-compat-ioctl32
module into videodev. There is no point in keeping them separate, as the
v4l2_compat_ioctl32() function is required by videodev if CONFIG_COMPAT
is set anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
WARNING: drivers/media/radio/built-in.o(.data+0x284): Section mismatch in reference from the variable fmr2_driver to the function .init.text:fmr2_probe()
The variable fmr2_driver references
the function __init fmr2_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/media/built-in.o(.data+0x48200): Section mismatch in reference from the variable fmr2_driver to the function .init.text:fmr2_probe()
The variable fmr2_driver references
the function __init fmr2_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card is based on the tea575x receiver. Use the tea575x-tuner framework
instead of reinventing the wheel.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tea575x-tuner module has been updated to use the latest V4L2 framework
functionality. This also required changes in the drivers that rely on it.
The tea575x changes are:
- The drivers must provide a v4l2_device struct to the tea module.
- The radio_nr module parameter must be part of the actual radio driver,
and not of the tea module.
- Changed the frequency range to the normal 76-108 MHz range instead of
50-150.
- Add hardware frequency seek support.
- Fix broken rxsubchans/audmode handling.
- The application can now select between stereo and mono.
- Support polling for control events.
- Add V4L2 priority handling.
And radio-sf16fmr2.c now uses the isa bus kernel framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When reading IF_AGC_GAIN register a wrong value for the base address
register was used (STB0899_DEMOD instead of STB0899_S2DEMOD). That
lead to a wrong signal strength value on DVB-S2 transponders.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_read_status the FE_HAS_SIGNAL flag was not set in case of a
successful carrier lock. This change fixes that.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b2a29b578d sets accidentally
supported delivery systems as DVB-T/T2 whilst it should be
DVB-S/S2. Due to that frontend cannot be used at all.
Reported-by: Jiří Zelenka <klacek@bubakov.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull networking changes from David Miller:
"1) icmp6_dst_alloc() returns NULL instead of ERR_PTR() leading to
crashes, particularly during shutdown. Reported by Dave Jones and
fixed by Eric Dumazet.
2) hyperv and wimax/i2400m return NETDEV_TX_BUSY when they have
already freed the SKB, which causes crashes as to the caller this
means requeue the packet. Fixes from Eric Dumazet.
3) usbnet driver doesn't allocate the right amount of headroom on
fresh RX SKBs, fix from Eric Dumazet.
4) Fix regression in ip6_mc_find_dev_rcu(), as an RCU lookup it
abolutely should not take a reference to 'dev', this leads to
leaks. Fix from RonQing Li.
5) Fix netfilter ctnetlink race between delete and timeout expiration.
From Pablo Neira Ayuso.
6) Revert SFQ change which causes regressions, specifically queueing
to tail can lead to unavoidable flow starvation. From Eric
Dumazet.
7) Fix a memory leak and a crash on corrupt firmware files in bnx2x,
from Michal Schmidt."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.
In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.
In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Also increments tx_dropped counter
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A driver start_xmit() method cannot free skb and return NETDEV_TX_BUSY,
since caller is going to reuse freed skb.
This is mostly a revert of commit bf769375c (staging: hv: fix the return
status of netvsc_start_xmit())
In fact netif_tx_stop_queue() / netif_stop_queue() is needed before
returning NETDEV_TX_BUSY or you can trigger a ksoftirqd fatal loop.
In case of memory allocation error, only safe way is to drop the packet
and return NETDEV_TX_OK
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
network drivers should reserve some headroom on incoming skbs so that we
dont need expensive reallocations, eg forwarding packets in tunnels.
This NET_SKB_PAD padding is done in various helpers, like
__netdev_alloc_skb_ip_align() in this patch, combining NET_SKB_PAD and
NET_IP_ALIGN magic.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.
Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge patches from Andrew Morton:
"Nine patches - some bug fixes and some MAINTAINERS fiddling."
* emailed from Andrew Morton <akpm@linux-foundation.org>:
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
MAINTAINERS: add Johan to Bluetooth maintainers
MAINTAINERS: Gustavo has moved
prctl: use CAP_SYS_RESOURCE for PR_SET_MM option
rapidio/tsi721: fix bug in register offset definitions
MAINTAINERS: update ST's Mailing list for SPEAr
memcg: free mem_cgroup by RCU to fix oops
Pull i2c subsystem fixes from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-algo-bit: Fix spurious SCL timeouts under heavy load
i2c-core: Comment says "transmitted" but means "received"
Pull drm exynos/intel updates from Dave Airlie:
"Two minor updates from Jesse for Intel SNB fixes, and a few fixes from
Samsung for exynos. The pull req has Alan's commit in it since Intel
based their tree on my tree at that time, but it all seems fine wrt
merging."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm exynos: use drm_fb_helper_set_par directly
drm/exynos: Fix fb_videomode <-> drm_mode_modeinfo conversion
drm/exynos: fix runtime_pm fimd device state on probe
drm/exynos: use correct 'exynos-drm' name for platform device
drm/i915: support 32 bit BGR formats in sprite planes
drm/i915: fix color order for BGR formats on SNB
drm/gma500: Fix Cedarview boot failures in 3.3-rc
Pull media fixes from Mauro Carvalho Chehab:
"For 4 fixes for 3.3 (all trivial):
- uvc video driver: fixes a division by zero;
- davinci: add module.h to fix compilation;
- smsusb: fix the delivery system setting;
- smsdvb: the get_frontend implementation there is broken.
The smsdvb patch has 127 lines, but it is trivial: instead of
returning a cache of the set_frontend (with is wrong, as it doesn't
have the updated values for the data, and the implementation there is
buggy), it copies the information of the detected DVB parameters from
the smsdvb private structures into the corresponding DVBv5 struct
fields."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] smsdvb: fix get_frontend
[media] smsusb: fix the default delivery system setting
[media] media: davinci: added module.h to resolve unresolved macros
[media] [FOR,v3.3] uvcvideo: Avoid division by 0 in timestamp calculation
Pull target fixes from Nicholas Bellinger:
"This series addresses two recently reported regression bugs related to
legacy SCSI reservation usage in target core, and iscsi-target
reservation conflict handling.
The second patch in particular addresses possible data-corruption with
SCSI reservations that is specific to iscsi-target fabric LUNs with
multiple client writers. Both patches need to go into v3.2 stable
ASAP, and the branch based on the last target-pending/3.3-rc-fixes
HEAD.
Again, thanks to Martin Svec for his help to identify and address this
regression bug with iscsi-target."
* '3.3-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix reservation conflict -EBUSY response handling bug
target: Fix compatible reservation handling (CRH=1) with legacy RESERVE/RELEASE
strict_strtoul() writes a long but ->gamma_mode only has space to store an
int, so on 64 bit systems we end up scribbling over ->gamma_table_count as
well. I've changed it to use kstrtouint() instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix indexed register offset definitions that use decimal (wrong) instead
of hexadecimal (correct) notation for indexing multipliers.
Incorrect definitions do not affect Tsi721 driver in its current default
configuration because it uses only IDB queue 0. Loss of inbound
doorbell functionality should be observed if queue other than 0 is used.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Chul Kim <chul.kim@idt.com>
Cc: <stable@vger.kernel.org> [3.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When the system is under heavy load, there can be a significant delay
between the getscl() and time_after() calls inside sclhi(). That delay
may cause the time_after() check to trigger after SCL has gone high,
causing sclhi() to return -ETIMEDOUT.
To fix the problem, double check that SCL is still low after the
timeout has been reached, before deciding to return -ETIMEDOUT.
Signed-off-by: Ville Syrjala <syrjala@sci.fi>
Cc: stable@vger.kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix that. Also convert this and the related comment to proper commenting
style.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'exynos-drm-fixes' of git://git.infradead.org/users/kmpark/linux-samsung:
drm exynos: use drm_fb_helper_set_par directly
drm/exynos: Fix fb_videomode <-> drm_mode_modeinfo conversion
drm/exynos: fix runtime_pm fimd device state on probe
drm/exynos: use correct 'exynos-drm' name for platform device
info->fix.visual already is correctly set from drm_fb_helper_fill_fix.
info->fix.line_length is also set from drm_fb_helper_fill_fix,
so drm_fb_helper_set_par directly instead of a custom
exynos_drm_fbdev_set_par.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The fb_videomode structure stores the front porch and back porch in the
right_margin and left_margin fields respectively. right_margin should
thus be computed with hsync_start - hdisplay, and left_margin with
htotal - hsync_end. The same holds for the vertical direction.
Active Front Sync Back
Region Porch Porch
<-------------------><----------------><-------------><---------------->
//////////////////|
////////////////// |
////////////////// |.................. ..................
_______________
<------ xres -------><- right_margin -><- hsync_len -><- left_margin -->
<---- hdisplay ----->
<------------ hsync_start ------------>
<--------------------- hsync_end -------------------->
<--------------------------------- htotal ----------------------------->
Fix the fb_videomode <-> drm_mode_modeinfo conversion functions
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
A call to pm_runtime_set_active() forces device to be at the active
state and skips calling its runtime suspend/resume callbacks. This
results in a freeze with a new power domain code based on gen_pd. Fimd
driver does all required runtime power management calls, so this
pm_runtime_set_active call is buggy. This patch removes it and corrects
clock management in probe function (clocks are now enabled by
pm_runtime_get_sync() call).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Currently Exynos DRM driver uses DRIVER_NAME ('exynos') name for the
core platform device. This is confusing, because it doesn't refer to the
function the platform device is performing. This patch renames the
platform device to the 'exynos-drm', which matches the convention for
naming the platform devices. The name used inside DRM subsystem has not
been changed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Pull block fixes from Jens Axboe:
"Been sitting on this for a while, but lets get this out the door.
This fixes various important bugs for 3.3 final, along with a few more
trivial ones. Please pull!"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix ioc leak in put_io_context
block, sx8: fix pointer math issue getting fw version
Block: use a freezable workqueue for disk-event polling
drivers/block/DAC960: fix -Wuninitialized warning
drivers/block/DAC960: fix DAC960_V2_IOCTL_Opcode_T -Wenum-compare warning
block: fix __blkdev_get and add_disk race condition
block: Fix setting bio flags in drivers (sd_dif/floppy)
block: Fix NULL pointer dereference in sd_revalidate_disk
block: exit_io_context() should call elevator_exit_icq_fn()
block: simplify ioc_release_fn()
block: replace icq->changed with icq->flags
in the da9052 driver and a bad return value in the tps6524x driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NzBr
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Another small batch of driver specific bug fixes, a couple more errors
in the da9052 driver and a bad return value in the tps6524x driver."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9052: Ensure the selected voltage falls within the specified range
regulator: Set n_voltages for da9052 regulators
regulator: Fix setting selector in tps6524x set_voltage function
