Trivial fix for two spelling mistakes.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
This short series fixes resource related logic in the driver, mostly
affecting the RDMA driver under corner cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea5 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver detects that resources have changed during open, it
should reset the rx and tx rings to 0. This will properly setup the
init sequence to initialize the default rings again. We also need
to signal the RDMA driver to stop and clear its interrupts. We then
call the RoCE driver to restart if a new set of default rings is
successfully reserved.
Fixes: 25e1acd6b9 ("bnxt_en: Notify firmware about IF state changes.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long says:
====================
sctp: two fixes for spp_ipv6_flowlabel and spp_dscp sockopts
This patchset fixes two problems in sctp_apply_peer_addr_params()
when setting spp_ipv6_flowlabel or spp_dscp.
====================
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When users set params.spp_address and get a trans, ipv6_flowlabel flag
should be applied into this trans. But even if this one is not an ipv6
trans, it should not go to apply it into all other transes of the asoc
but simply ignore it.
Fixes: 0b0dce7a36 ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in sctp_apply_peer_addr_params(), if SPP_IPV6_FLOWLABEL flag is set
and trans is NULL, it would use trans as the index variable to traverse
transport_addr_list, then trans is set as the last transport of it.
Later, if SPP_DSCP flag is set, it would enter into the wrong branch as
trans is actually an invalid reference.
So fix it by using a new index variable to traverse transport_addr_list
for both SPP_DSCP and SPP_IPV6_FLOWLABEL flags process.
Fixes: 0b0dce7a36 ("sctp: add spp_ipv6_flowlabel and spp_dscp for sctp_paddrparams")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__emac_calc_base_mr1 was used instead of __emac4_calc_base_mr1
by copy-paste mistake for emac4syn.
Fixes: 45d6e54550 ("net/ibm/emac: add 8192 rx/tx fifo size")
Signed-off-by: Ivan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit afb2c4437d ("drm/i915/ddi: Push pipe clock enabling to encoders")
inadvertently stopped enabling the pipe clock for any DP-MST stream
after the first one. It also rearranged the pipe clock enabling wrt.
initial MST payload allocation step (which may or may not be a
problem, but it's contrary to the spec.).
Fix things by making the above commit truly a non-functional change.
Fixes: afb2c4437d ("drm/i915/ddi: Push pipe clock enabling to encoders")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107365
Reported-by: Lyude Paul <lyude@redhat.com>
Reported-by: dmummenschanz@web.de
Tested-by: dmummenschanz@web.de
Tested-by: Lyude Paul <lyude@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: dmummenschanz@web.de
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180831174739.30387-1-imre.deak@intel.com
(cherry picked from commit 2b5cf4ef54)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
This re-applies the workaround for "some DP sinks, [which] are a
little nuts" from commit 1a36147bb9 ("drm/i915: Perform link
quality check unconditionally during long pulse").
It makes the secondary AOC E2460P monitor connected via DP to an
acer Veriton N4640G usable again.
This hunk was dropped in commit c85d200e83 ("drm/i915: Move SST
DP link retraining into the ->post_hotplug() hook")
Fixes: c85d200e83 ("drm/i915: Move SST DP link retraining into the ->post_hotplug() hook")
[Cleaned up commit message, added stable cc]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jan-Marek Glogowski <glogow@fbihome.de>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20180825191035.3945-1-lyude@redhat.com
(cherry picked from commit 3cf71bc990)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The _IOC_READ flag fits this ioctl request more because this request
actually only writes to, but doesn't read from userspace.
See NOTEs in include/uapi/asm-generic/ioctl.h for more information.
Fixes: 429711aec2 ("vhost: switch to use new message format")
Signed-off-by: Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An online resize of a file system with the bigalloc feature enabled
and a 1k block size would be refused since ext4_resize_begin() did not
understand s_first_data_block is 0 for all bigalloc file systems, even
when the block size is 1k.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
Avoid growing the file system to an extent so that the last block
group is too small to hold all of the metadata that must be stored in
the block group.
This problem can be triggered with the following reproducer:
umount /mnt
mke2fs -F -m0 -b 4096 -t ext4 -O resize_inode,^has_journal \
-E resize=1073741824 /tmp/foo.img 128M
mount /tmp/foo.img /mnt
truncate --size 1708M /tmp/foo.img
resize2fs /dev/loop0 295400
umount /mnt
e2fsck -fy /tmp/foo.img
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org
This card identifies itself as:
Ethernet controller [0200]: NCube Device [10ff:8168] (rev 06)
Subsystem: TP-LINK Technologies Co., Ltd. Device [7470:3468]
Adding a new entry to rtl8169_pci_tbl makes the card work.
Link: http://launchpad.net/bugs/1788730
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
man ip-tunnel ttl section says:
0 is a special value meaning that packets inherit the TTL value.
IPv4 tunnel respect this in ip_tunnel_xmit(), but IPv6 tunnel has not
implement it yet. To make IPv6 behave consistently with IP tunnel,
add ipv6 tunnel inherit support.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E.g. for snd_hdac_ext_link_clear_stream_id(), we should set (1 << stream)
as mask, and 0 as value, here correct it and several similar mismatches.
And, here also remove unreadable register_mask usage for those mask value
updating.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clocking operations clk_get/set_rate, are non-atomic,
they shouldn't be called in soc_pcm_trigger() which is atomic.
Following issue was found due to execution of clk_get_rate() causes
sleep in soc_pcm_trigger(), which shouldn't be blocked.
We can reproduce this issue by following
> enable CONFIG_DEBUG_ATOMIC_SLEEP=y
> compile, and boot
> mount -t debugfs none /sys/kernel/debug
> while true; do cat /sys/kernel/debug/clk/clk_summary > /dev/null; done &
> while true; do aplay xxx; done
This patch adds support to .prepare callback, and moves non-atomic
clocking operations to it. As .prepare is non-atomic, it is always
called before trigger_start/trigger_stop.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620
in_atomic(): 1, irqs_disabled(): 128, pid: 2242, name: aplay
INFO: lockdep is turned off.
irq event stamp: 5964
hardirqs last enabled at (5963): [<ffff200008e59e40>] mutex_lock_nested+0x6e8/0x6f0
hardirqs last disabled at (5964): [<ffff200008e623f0>] _raw_spin_lock_irqsave+0x24/0x68
softirqs last enabled at (5502): [<ffff200008081838>] __do_softirq+0x560/0x10c0
softirqs last disabled at (5495): [<ffff2000080c2e78>] irq_exit+0x160/0x25c
Preemption disabled at:[ 62.904063] [<ffff200008be4d48>] snd_pcm_stream_lock+0xb4/0xc0
CPU: 2 PID: 2242 Comm: aplay Tainted: G B C 4.9.54+ #186
Hardware name: Renesas Salvator-X board based on r8a7795 (DT)
Call trace:
[<ffff20000808fe48>] dump_backtrace+0x0/0x37c
[<ffff2000080901d8>] show_stack+0x14/0x1c
[<ffff2000086f4458>] dump_stack+0xfc/0x154
[<ffff2000081134a0>] ___might_sleep+0x57c/0x58c
[<ffff2000081136b8>] __might_sleep+0x208/0x21c
[<ffff200008e5980c>] mutex_lock_nested+0xb4/0x6f0
[<ffff2000087cac74>] clk_prepare_lock+0xb0/0x184
[<ffff2000087cb094>] clk_core_get_rate+0x14/0x54
[<ffff2000087cb0f4>] clk_get_rate+0x20/0x34
[<ffff20000113aa00>] rsnd_adg_ssi_clk_try_start+0x158/0x4f8 [snd_soc_rcar]
[<ffff20000113da00>] rsnd_ssi_init+0x668/0x7a0 [snd_soc_rcar]
[<ffff200001133ff4>] rsnd_soc_dai_trigger+0x4bc/0xcf8 [snd_soc_rcar]
[<ffff200008c1af24>] soc_pcm_trigger+0x2a4/0x2d4
Fixes: e7d850dd10 ("ASoC: rsnd: use mod base common method on SSI-parent")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Timo Wischer <twischer@de.adit-jv.com>
[Kuninori: tidyup for upstream]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
syzbot reported the uninitialized value exposure in certain situations
using virmidi loop. It's likely a very small race at writing and
reading, and the influence is almost negligible. But it's safer to
paper over this just by replacing the existing kvmalloc() with
kvzalloc().
Reported-by: syzbot+194dffdb8b22fc5d207a@syzkaller.appspotmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 92183a4289 ("fsnotify: fix ignore mask logic in
send_to_group()") acknoledges the use case of ignoring an event on
an inode mark, because of an ignore mask on a mount mark of the same
group (i.e. I want to get all events on this file, except for the events
that came from that mount).
This change depends on correctly merging the inode marks and mount marks
group lists, so that the mount mark ignore mask would be tested in
send_to_group(). Alas, the merging of the lists did not take into
account the case where event in question is not in the mask of any of
the mount marks.
To fix this, completely remove the tests for inode and mount event masks
from the lists merging code.
Fixes: 92183a4289 ("fsnotify: fix ignore mask logic in send_to_group")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
It is read_persistent_wall_and_boot_offset() and not
read_persistent_clock_and_boot_offset()
Fixes: 3eca993740 ("timekeeping: Replace read_boot_clock64() with read_persistent_wall_and_boot_offset()")
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Pavel Tatashin <pasha.tatashin@oracle.com>
Link: https://lkml.kernel.org/r/20180903081533.34366-1-borntraeger@de.ibm.com
Some of the router data fields are left as default zeros which are
valid dai ids, so initialize these to invalid value of -1.
Without intializing these correctly get_session_from_id() can return
incorrect session resulting in not closing the opened copp and messing
up with the copp ref count.
Fixes: e3a33673e8 ("ASoC: qdsp6: q6routing: Add q6routing driver")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix kernel-doc warnings in arch/x86/include/asm/atomic.h that are caused by
having a #define macro between the kernel-doc notation and the function
name. Fixed by moving the #define macro to after the function
implementation.
Make the same change for atomic64_{32,64}.h for consistency even though
there were no kernel-doc warnings found in these header files, but there
would be if they were used in generation of documentation.
Fixes these kernel-doc warnings:
../arch/x86/include/asm/atomic.h:84: warning: Excess function parameter 'i' description in 'arch_atomic_sub_and_test'
../arch/x86/include/asm/atomic.h:84: warning: Excess function parameter 'v' description in 'arch_atomic_sub_and_test'
../arch/x86/include/asm/atomic.h:96: warning: Excess function parameter 'v' description in 'arch_atomic_inc'
../arch/x86/include/asm/atomic.h:109: warning: Excess function parameter 'v' description in 'arch_atomic_dec'
../arch/x86/include/asm/atomic.h:124: warning: Excess function parameter 'v' description in 'arch_atomic_dec_and_test'
../arch/x86/include/asm/atomic.h:138: warning: Excess function parameter 'v' description in 'arch_atomic_inc_and_test'
../arch/x86/include/asm/atomic.h:153: warning: Excess function parameter 'i' description in 'arch_atomic_add_negative'
../arch/x86/include/asm/atomic.h:153: warning: Excess function parameter 'v' description in 'arch_atomic_add_negative'
Fixes: 18cc1814d4 ("atomics/treewide: Make test ops optional")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lkml.kernel.org/r/0a1e678d-c8c5-b32c-2640-ed4e94d399d2@infradead.org
When tracing is enabled, all the debug messages are recorded and must
not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the
user with:
WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Call Trace:
__sdata_dbg+0xbd/0x120 [mac80211]
ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
ieee80211_iface_work+0x21d/0x320 [mac80211]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.
Make sure that we don't send the deauthentication frame in
this case.
In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We hit a problem with iwlwifi that was caused by a bug in
mac80211. A bug in iwlwifi caused the firwmare to crash in
certain cases in channel switch. Because of that bug,
drv_pre_channel_switch would fail and trigger the restart
flow.
Now we had the hw restart worker which runs on the system's
workqueue and the csa_connection_drop_work worker that runs
on mac80211's workqueue that can run together. This is
obviously problematic since the restart work wants to
reconfigure the connection, while the csa_connection_drop_work
worker does the exact opposite: it tries to disconnect.
Fix this by cancelling the csa_connection_drop_work worker
in the restart worker.
Note that this can sound racy: we could have:
driver iface_work CSA_work restart_work
+++++++++++++++++++++++++++++++++++++++++++++
|
<--drv_cs ---|
<FW CRASH!>
-CS FAILED-->
| |
| cancel_work(CSA)
schedule |
CSA work |
| |
Race between those 2
But this is not possible because we flush the workqueue
in the restart worker before we cancel the CSA worker.
That would be bullet proof if we could guarantee that
we schedule the CSA worker only from the iface_work
which runs on the workqueue (and not on the system's
workqueue), but unfortunately we do have an instance
in which we schedule the CSA work outside the context
of the workqueue (ieee80211_chswitch_done).
Note also that we should probably cancel other workers
like beacon_connection_loss_work and possibly others
for different types of interfaces, at the very least,
IBSS should suffer from the exact same problem, but for
now, do the minimum to fix the actual bug that was actually
experienced and reproduced.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 9236c4523e5b ("mac80211: limit wmm params to comply
with ETSI requirements"), we have limited the WMM parameters to
comply with 802.11 and ETSI standard. Mistakenly the TXOP value
was caluclated wrong. Fix it by taking the minimum between
802.11 to ETSI to make sure we are not violating both.
Fixes: e552af0581 ("mac80211: limit wmm params to comply with ETSI requirements")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The "chandef->center_freq1" variable is a u32 but "freq" is a u16 so we
are truncating away the high bits. I noticed this bug because in commit
9cf0a0b4b6 ("cfg80211: Add support for 60GHz band channels 5 and 6")
we made "freq <= 56160 + 2160 * 6" a valid requency when before it was
only "freq <= 56160 + 2160 * 4" that was valid. It introduces a static
checker warning:
net/wireless/util.c:1571 ieee80211_chandef_to_operating_class()
warn: always true condition '(freq <= 56160 + 2160 * 6) => (0-u16max <= 69120)'
But really we probably shouldn't have been truncating the high bits
away to begin with.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Initialize 'n' to 2 in order to take into account also the first
packet in the estimation of max_subframe limit for a given A-MSDU
since frag_tail pointer is NULL when ieee80211_amsdu_aggregate
routine analyzes the second frame.
Fixes: 6e0456b545 ("mac80211: add A-MSDU tx support")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This trys to give new born vGPU with higher scheduling chance
not only with adding to sched list head and also have higher
priority for workload sched for 2 seconds after starting to
schedule it. In order for fast GPU execution during VM boot,
and ensure guest driver setup with required state given in time.
This fixes recent failure seen on one VM with multiple linux VMs
running on kernel with commit 2621cefaa42b3("drm/i915: Provide a timeout to i915_gem_wait_for_idle() on setup"),
which had shorter setup timeout that caused context state init failed.
v2: change to 2s for higher scheduling period
Cc: Yuan Hang <hang.yuan@intel.com>
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
This patch is required allows access to a Microsoft fileserver failover
cluster behind a 1:1 NAT firewall.
The change also provides stronger context for authentication and share
connection (see MS-SMB2 3.3.5.7 and MS-SRVS 3.1.6.8) as noted by
Tom Talpey, and addresses comments about the buffer size for the UNC
made by Aurélien Aptel.
Signed-off-by: Thomas Werschlein <thomas.werschlein@geo.uzh.ch>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Tom Talpey <ttalpey@microsoft.com>
Reviewed-by: Aurelien Aptel <aaptel@suse.com>
CC: Stable <stable@vger.kernel.org>
Although servers will typically ignore unsupported features,
we should advertise the support for directory leases (as
Windows e.g. does) in the negotiate protocol capabilities we
pass to the server, and should check for the server capability
(CAP_DIRECTORY_LEASING) before sending a lease request for an
open of a directory. This will prevent us from accidentally
sending directory leases to SMB2.1 or SMB2 server for example.
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
I ran into some cases where server was returning the wrong length
on frames but I couldn't easily match them to the command in the
network trace (or server logs) since I need the command and/or
multiplex id to find the offending SMB2/SMB3 command. Add these
two fields to the log message. In the case of padding too much
it may not be a problem in all cases but might have correlated
to a network disconnect case in some problems we have been
looking at. In the case of frame too short is even more important.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
When "backup intent" is requested on the mount (e.g. backupuid or
backupgid mount options), the corresponding flag needs to be set
on opens of directories (and files) but was missing in some
places causing access denied trying to enumerate and backup
servers.
Fixes kernel bugzilla #200953https://bugzilla.kernel.org/show_bug.cgi?id=200953
Reported-and-tested-by: <whh@rubrik.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
When a Mac client saves an item containing a backslash to a file server
the backslash is represented in the CIFS/SMB protocol as as U+F026.
Before this change, listing a directory containing an item with a
backslash in its name will return that item with the backslash
represented with a true backslash character (U+005C) because
convert_sfm_character mapped U+F026 to U+005C when interpretting the
CIFS/SMB protocol response. However, attempting to open or stat the
path using a true backslash will result in an error because
convert_to_sfm_char does not map U+005C back to U+F026 causing the
CIFS/SMB request to be made with the backslash represented as U+005C.
This change simply prevents the U+F026 to U+005C conversion from
happenning. This is analogous to how the code does not do any
translation of UNI_SLASH (U+F000).
Signed-off-by: Jon Kuhn <jkuhn@barracuda.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
A few fixes for the fallout of being a little more pedantic about
dma masks.
-----BEGIN PGP SIGNATURE-----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=GFai
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-4.19-2' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"A few fixes for the fallout of being a little more pedantic about dma
masks"
* tag 'dma-mapping-4.19-2' of git://git.infradead.org/users/hch/dma-mapping:
of/platform: initialise AMBA default DMA masks
sparc: set a default 32-bit dma mask for OF devices
kernel/dma/direct: take DMA offset into account in dma_direct_supported
The bootmem to memblock conversion introduced by the commit 1008a11590
("m68k: switch to MEMBLOCK + NO_BOOTMEM") made reservation of kernel code
and data to start from a wrong address.
Fix it.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Include linux/in6.h for struct in6_addr.
/usr/include/linux/rds.h:156:18: error: field ‘laddr’ has incomplete type
struct in6_addr laddr;
^~~~~
/usr/include/linux/rds.h:157:18: error: field ‘faddr’ has incomplete type
struct in6_addr faddr;
^~~~~
/usr/include/linux/rds.h:178:18: error: field ‘laddr’ has incomplete type
struct in6_addr laddr;
^~~~~
/usr/include/linux/rds.h:179:18: error: field ‘faddr’ has incomplete type
struct in6_addr faddr;
^~~~~
/usr/include/linux/rds.h:198:18: error: field ‘bound_addr’ has incomplete type
struct in6_addr bound_addr;
^~~~~~~~~~
/usr/include/linux/rds.h:199:18: error: field ‘connected_addr’ has incomplete type
struct in6_addr connected_addr;
^~~~~~~~~~~~~~
/usr/include/linux/rds.h:219:18: error: field ‘local_addr’ has incomplete type
struct in6_addr local_addr;
^~~~~~~~~~
/usr/include/linux/rds.h:221:18: error: field ‘peer_addr’ has incomplete type
struct in6_addr peer_addr;
^~~~~~~~~
/usr/include/linux/rds.h:245:18: error: field ‘src_addr’ has incomplete type
struct in6_addr src_addr;
^~~~~~~~
/usr/include/linux/rds.h:246:18: error: field ‘dst_addr’ has incomplete type
struct in6_addr dst_addr;
^~~~~~~~
Fixes: b7ff8b1036 ("rds: Extend RDS API for IPv6 support")
Signed-off-by: Vinson Lee <vlee@freedesktop.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel module may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] usleep_range
drivers/net/ethernet/cadence/macb_main.c, 648:
usleep_range in macb_halt_tx
drivers/net/ethernet/cadence/macb_main.c, 730:
macb_halt_tx in macb_tx_error_task
drivers/net/ethernet/cadence/macb_main.c, 721:
_raw_spin_lock_irqsave in macb_tx_error_task
To fix this bug, usleep_range() is replaced with udelay().
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-09-02
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix one remaining buggy offset override in sockmap's bpf_msg_pull_data()
when linearizing multiple scatterlist elements, from Tushar.
2) Fix BPF sockmap's misuse of ULP when a collision with another ULP is
found on map update where it would release existing ULP. syzbot found and
triggered this couple of times now, fix from John.
3) Add missing xskmap type to bpftool so it will properly show the type
on map dump, from Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mx8dv never entered into production and there is no other place
in the kernel referring to this SoC, so remove it from the
driver's compatible entry.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mx8dv never entered into production and there is no other place
in the kernel referring to this SoC, so remove it from the
dt bindings documentation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver currently emits a STOP if the next message is not
I2C_MD_RD. It should not do it because it disturbs the I2C_RDWR
ioctl, where read/write transactions are combined without STOP
between.
Issue STOP only when the message is the last one _or_ flagged with
I2C_M_STOP.
Fixes: 6a62974b66 ("i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>