* 'stable/drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Have 'passthrough' option instead of XEN_PCIDEV_BACKEND_PASS and XEN_PCIDEV_BACKEND_VPCI
xen/pciback: Remove the DEBUG option.
xen/pciback: Drop two backends, squash and cleanup some code.
xen/pciback: Print out the MSI/MSI-X (PIRQ) values
xen/pciback: Don't setup an fake IRQ handler for SR-IOV devices.
xen: rename pciback module to xen-pciback.
xen/pciback: Fine-grain the spinlocks and fix BUG: scheduling while atomic cases.
xen/pciback: Allocate IRQ handler for device that is shared with guest.
xen/pciback: Disable MSI/MSI-X when reseting a device
xen/pciback: guest SR-IOV support for PV guest
xen/pciback: Register the owner (domain) of the PCI device.
xen/pciback: Cleanup the driver based on checkpatch warnings and errors.
xen/pciback: xen pci backend driver.
xen: tmem: self-ballooning and frontswap-selfshrinking
xen: Add module alias to autoload backend drivers
xen: Populate xenbus device attributes
xen: Add __attribute__((format(printf... where appropriate
xen: prepare tmem shim to handle frontswap
xen: allow enable use of VGA console on dom0
* 'stable/pci.cleanups.v1' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: Use 'acpi_gsi_to_irq' value unconditionally.
xen/pci: Remove 'xen_allocate_pirq_gsi'.
xen/pci: Retire unnecessary #ifdef CONFIG_ACPI
xen/pci: Move the allocation of IRQs when there are no IOAPIC's to the end
xen/pci: Squash pci_xen_initial_domain and xen_setup_pirqs together.
xen/pci: Use the xen_register_pirq for HVM and initial domain users
xen/pci: In xen_register_pirq bind the GSI to the IRQ after the hypercall.
xen/pci: Provide #ifdef CONFIG_ACPI to easy code squashing.
xen/pci: Update comments and fix empty spaces.
xen/pci: Shuffle code around.
Adds README file, TODO list, and a couple of other pieces that didn't seem
to fit into any other patch.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The OpenRISC Linux kernel conforms to the "generic" syscall interface which
contains only the reduced set of syscalls deemed necessary for new
architectures. Unfortunately, the uClibc port for OpenRISC does not fully
support this reduced set; as such, an additional patch available out-of-tree
needs to be applied to the kernel in order to use the current uClibc. This
is just a temporary measure until the libc port can be straightened out; it
is likely that OpenRISC will make the transition to glibc shortly where the
generic syscall interface is better supported.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch adds support for the OpenRISC PIC.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: tglx@linutronix.de
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Implements support for the OpenRISC timer which is a 28 bit cycle counter
that can be read out of a special purpose register. This counter is
used as a both a clock event and clocksource device.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: tglx@linutronix.de
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch implements minimal PTrace support. The pt_regs structure is
not exported to userspace for OpenRISC; rather, the GETREGSET mechanism
is intended to be used and the registers, as such, exported in the core
dump format which is ABI stable. This is in line with what is intended
for new architectures as of 2.6.34 and has the advantage of permitting
the layout of the registers on the kernel stack (as per pt_regs) to be
freely modified.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
The OpenRISC architecture uses the device tree infrastructure for the
platform description. This is currently limited to having a device tree
built into the kernel, but work is underway within the OpenRISC project
to define how this device tree blob should be passed into the kernel from
an external resource.
Patch contains a single example DTS file to go with the defconfig for
or1ksim.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Cc: devicetree-discuss@lists.ozlabs.org
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Architecture code and early setup routines for booting Linux.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
This patch moves the in-tree architectures that were using the 'generic'
delay.h over to using the header file in asm-generic.
This is not done using the generic-y mechanism as none of these arch's
have started using that mechanism yet. This is a trivial change to make
later when the arch begins using generic-y.
Note the subtle change to the avr32 and SH architectures where the argument
to __const_udelay was previously using the rounded down constant value
instead of the rounded up value.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Building kernel 3.0 for an n2100 (plat-iop) results in:
In file included from arch/arm/plat-iop/cp6.c:20:
/tmp/linux-3.0/arch/arm/include/asm/traps.h:12: warning: 'struct pt_regs' declared inside parameter list
/tmp/linux-3.0/arch/arm/include/asm/traps.h:12: warning: its scope is only this definition or declaration, which is probably not what you want
/tmp/linux-3.0/arch/arm/include/asm/traps.h:48: warning: 'struct pt_regs' declared inside parameter list
/tmp/linux-3.0/arch/arm/include/asm/traps.h:48: warning: 'struct task_struct' declared inside parameter list
arch/arm/plat-iop/cp6.c:45: warning: initialization from incompatible pointer type
Nothing here depends on the layout of pt_regs or task_struct, so this
can be fixed by adding forward struct declarations to asm/traps.h.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
pit_clockevent wants to replaced in the argument of the callback
function as well.
Reported-by; Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Improve scalability by avoiding costly and unnecessary L2 cache sync
in handling bitops.
Signed-off-by: Heechul Yun <hyun@nvidia.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've got hands on one ts-7300 board, which is equiped with 128MB RAM in two
64MB memory chips, so it's 16 banks/8MB each. Without this patch, the bootmem
init code complains about small NR_BANKS number and only lower 64MB is
accessible.
Cc: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change the string to check for CAMP mode boot on MPC85xx (eg. P2020) to match
the one in the corresponding dts files (p2020rdb_camp_core{0,1}.dts).
Without this fix the mpic is configured as in the SMP boot mode, which causes
the first core to report a protected source interrupt error for devices
of the other core and lock up.
Also add MPIC_SINGLE_DEST_CPU on both P2020 based architectures in CAMP
mode as suggested by Scott Wood. Thanks.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The comment is outdated, wikipedia now has six translations of the cpuid
page.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch fixes three typos I've accidentally spotted.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (one was already fixed)
We switch back from using vmcall in 091ebf07a2
because it was unreliable under kvm, but I missed one (rarely-used) place.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The Host used to create some page tables for the Guest to use at the
top of Guest memory; it would then tell the Guest where this was. In
particular, it created linear mappings for 0 and 0xC0000000 addresses
because lguest used to switch to its real page tables quite late in
boot.
However, since d50d8fe19 Linux initialized boot page tables in
head_32.S even before the "are we lguest?" boot jump. So, now we can
simplify things: the Host pagetable code assumes 1:1 linear mapping
until it first calls the LHCALL_NEW_PGTABLE hypercall, which we now do
before we reach C code.
This also means that the Host doesn't need to know anything about the
Guest's PAGE_OFFSET. (Non-Linux guests might not even have such a
thing).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We already did it for hard IRQs but it looks like we forgot
to do it for softirqs. Without this, we would lose flags
such as TIF_NEED_RESCHED set using current_thread_info()
by something running of a softirq.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The 64-bit Book-E parts (to date) dont utilize the 'server' class
perfmon. So building or depending on it makes no sense (and does break
FSL Book-E 64-bit support). Move the selection of PPC_HAVE_PMU_SUPPORT
to be based on PPC_BOOK3S_64.
Based on a patch from Scott Wood.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 63ab25ebbc (kgdbts: unify/generalize gdb breakpoint adjustment)
introduced a compile regression on sparc.
kgdbts.c: In function 'check_and_rewind_pc':
kgdbts.c:307: error: implicit declaration of function 'instruction_pointer_set'
Simply add the correct macro definition for instruction pointer on the
Sparc architecture.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David S. Miller <davem@davemloft.net>
The machinery for __ARCH_HAS_CLOCKSOURCE_DATA assumed a file in
asm-generic would be the default for architectures without their own
file in asm/, but that is not how it works.
Replace it with a Kconfig option instead.
Link: http://lkml.kernel.org/r/4E288AA6.7090804@zytor.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andy Lutomirski <luto@mit.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Tony Luck <tony.luck@intel.com>
An implementation of a code generator for BPF programs to speed up packet
filtering on PPC64, inspired by Eric Dumazet's x86-64 version.
Filter code is generated as an ABI-compliant function in module_alloc()'d mem
with stackframe & prologue/epilogue generated if required (simple filters don't
need anything more than an li/blr). The filter's local variables, M[], live in
registers. Supports all BPF opcodes, although "complicated" loads from negative
packet offsets (e.g. SKF_LL_OFF) are not yet supported.
There are a couple of further optimisations left for future work; many-pass
assembly with branch-reach reduction and a register allocator to push M[]
variables into volatile registers would improve the code quality further.
This currently supports big-endian 64-bit PowerPC only (but is fairly simple
to port to PPC32 or LE!).
Enabled in the same way as x86-64:
echo 1 > /proc/sys/net/core/bpf_jit_enable
Or, enabled with extra debug output:
echo 2 > /proc/sys/net/core/bpf_jit_enable
Signed-off-by: Matt Evans <matt@ozlabs.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yet another variant of the Dell Latitude series which requires
reboot=pci.
From the E5420 bug report by Daniel J Blueman:
> The E6420 is affected also (same platform, different casing and
> features), which provides an external confirmation of the issue; I can
> submit a patch for that later or include it if you prefer:
> http://linux.koolsolutions.com/2009/08/04/howto-fix-linux-hangfreeze-during-reboots-and-restarts/
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Rebooting on the Dell E5420 often hangs with the keyboard or ACPI
methods, but is reliable via the PCI method.
[ hpa: this was deferred because we believed for a long time that the
recent reshuffling of the boot priorities in commit
660e34cebf fixed this platform.
Unfortunately that turned out to be incorrect. ]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1305248699-2347-1-git-send-email-daniel.blueman@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
copy_from_user_nmi() is used in oprofile and perf. Moving it to other
library functions like copy_from_user(). As this is x86 code for 32
and 64 bits, create a new file usercopy.c for unified code.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110607172413.GJ20052@erda.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch:
- fixes typos in comments and clarifies the text
- renames obscure p4_event_alias::original and ::alter members to
::original and ::alternative as appropriate
- drops parenthesis from the return of p4_get_alias_event()
No functional changes.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Link: http://lkml.kernel.org/r/20110721160625.GX7492@sun
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 66a625a (ARM: mm: proc-macros: Add generic proc/cache/tlb struct
definition macros) introduced build errors when PM_SLEEP is not enabled.
The per-CPU do_suspend/do_resume functions are defined via the
preprocessor to constant 0. However, the macros which use these were
converted to assembly, resulting in undefined references to these
functions. Fix that by moving the ! ifdef section into proc-macros.S
and deleting it from all effected proc-*.S files.
Acked-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Previously we just assumed there were CONFIG_NR_CPUS cpus present in
the system. Instead, figure out the number of cpus from the MIDR
register.
Signed-off-by: Jeff Ohlstein <johlstei@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
[arnd: clarified patch title]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Our selection of interrupts to consider for IRQ migration is sub-
standard. We were potentially including per-CPU interrupts in our
migration strategy, but omitting chained interrupts. This caused
some interrupts to remain on a downed CPU.
We were also trying to migrate interrupts which were not migratable,
resulting in an OOPS.
Instead, iterate over all interrupts, skipping per-CPU interrupts
or interrupts whose affinity does not include the downed CPU, and
attempt to set the affinity for every one else if their chip
implements irq_set_affinity().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the GIC takes care of selecting a target interrupt from the
affinity mask, we don't need all this complexity in the core code
anymore. Just detect when we need to break affinity.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The irq_set_affinity() method can be called with masks which include
offline CPUs. This allows offline CPUs to have interrupts routed to
them by writing to /proc/irq/*/smp_affinity after hotplug has taken
a CPU offline. Fix this by ensuring that we select a target CPU
present in both the required affinity and the online CPU mask.
Ensure that we return IRQ_SET_MASK_OK (which happens to be 0) on
success to ensure generic code copies the new mask into the irq_data
structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irqdesc's node member is supposed to mark the numa node number for the
interrupt. Our use of it is non-standard. Remove this, replacing the
functionality with a test of the affinity mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In kexec jump support, jump back address passed to the kexeced
kernel via function calling ABI, that is, the function call
return address is the jump back entry.
Furthermore, jump back entry == 0 should be used to signal that
the jump back or preserve context is not enabled in the original
kernel.
But in the current implementation the stack position used for
function call return address is not cleared context
preservation is disabled. The patch fixes this bug.
Reported-and-tested-by: Yin Kangkai <kangkai.yin@intel.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1310607277-25029-1-git-send-email-ying.huang@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to carve up the configuration between:
- MID general
- Moorestown specific
- Medfield specific
- Future devices
As a base point create an INTEL_MID configuration property. We
make the existing MRST configuration a sub-option. This means
that the rest of the kernel config can still use X86_MRST checks
without anything going backwards.
After this is merged future patches will tidy up which devices
are MID and which are X86_MRST, as well as add options for
Medfield.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Link: http://lkml.kernel.org/r/20110712164859.7642.84136.stgit@bob.linux.org.uk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This code uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it wasn't converted by commit 44c10138fd ("PCI: Change all
drivers to use pci_device->revision") before being moved to arch/x86/...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dave Jones <davej@redhat.com>
Link: http://lkml.kernel.org/r/201107111901.39281.sshtylyov@ru.mvista.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The EFI specification requires that callers of the time related
runtime functions serialize with other CMOS accesses in the
kernel, as the EFI time functions may choose to also use the
legacy CMOS RTC.
Besides fixing a latent bug, this is a prerequisite to safely
enable the rtc-efi driver for x86, which ought to be preferred
over rtc-cmos on all EFI platforms.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: <mjg@redhat.com>
Link: http://lkml.kernel.org/r/4E257E33020000780004E319@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Matthew Garrett <mjg@redhat.com>
With CPU hotplug, there is a theoretical race between other CMOS
(namely RTC) accesses and those done in the SMP secondary
processor bringup path.
I am unware of the problem having been noticed by anyone in practice,
but it would very likely be rather spurious and very hard to reproduce.
So to be on the safe side, acquire rtc_lock around those accesses.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: John Stultz <john.stultz@linaro.org>
Link: http://lkml.kernel.org/r/4E257AE7020000780004E2FF@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
According to SoC name, EXYNOS4, this patch changes devname
for FIMD from 's5pv310-fb' to 'exynos4-fb'.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[kgene.kim@samsung.com: removed to change wrong clock name]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
With the write lock path simply subtracting RW_LOCK_BIAS there
is, on large systems, the theoretical possibility of overflowing
the 32-bit value that was used so far (namely if 128 or more
CPUs manage to do the subtraction, but don't get to do the
inverse addition in the failure path quickly enough).
A first measure is to modify RW_LOCK_BIAS itself - with the new
value chosen, it is good for up to 2048 CPUs each allowed to
nest over 2048 times on the read path without causing an issue.
Quite possibly it would even be sufficient to adjust the bias a
little further, assuming that allowing for significantly less
nesting would suffice.
However, as the original value chosen allowed for even more
nesting levels, to support more than 2048 CPUs (possible
currently only for 64-bit kernels) the lock itself gets widened
to 64 bits.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4E258E0D020000780004E3F0@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rather than having two functionally identical implementations
for 32- and 64-bit configurations, use the previously extended
assembly abstractions to fold the rwsem two implementations into
a shared one.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4E258DF3020000780004E3ED@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rather than having two functionally identical implementations
for 32- and 64-bit configurations, extend the existing assembly
abstractions enough to fold the two rwlock implementations into
a shared one.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/4E258DD7020000780004E3EA@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Btrfs needs to be able to control how filemap_write_and_wait_range() is called
in fsync to make it less of a painful operation, so push down taking i_mutex and
the calling of filemap_write_and_wait() down into the ->fsync() handlers. Some
file systems can drop taking the i_mutex altogether it seems, like ext3 and
ocfs2. For correctness sake I just pushed everything down in all cases to make
sure that we keep the current behavior the same for everybody, and then each
individual fs maintainer can make up their mind about what to do from there.
Thanks,
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86. reboot: Make Dell Latitude E6320 use reboot=pci
x86, doc only: Correct real-mode kernel header offset for init_size
x86: Disable AMD_NUMA for 32bit for now
Fix few issues in the Netlogic code:
- Use handle_percpu_irq to handle per-cpu interrupts
- Remove unused function nlm_common_ipi_handler()
- Call scheduler_ipi() on SMP_RESCHEDULE_YOURSELF
- Enable interrupts in nlm_smp_finish()
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2460/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit d6d5d5c4a (MIPS: Sibyte: Convert to new irq_chip functions)
removed the mask function which breaks irq_shutdown(). Restore it.
Reported-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2460/
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since 6be63bbbda (lmo) rsp.
af3a1f6f48 (kernel.org) the Malta code does
no longer probe for presence of GCMP if CMP is not configured. This means
that the variable gcmp_present well be left at its default value of -1
which normally is meant to indicate that GCMP has not yet been mmapped.
This non-zero value is now interpreted as GCMP being present resulting
in a write attempt to a GCMP register resulting in a crash.
Reported and a build fix on top of my fix by Rob Landley <rob@landley.net>.
Reported-by: Rob Landley <rob@landley.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2413/
Renumbering was necessary because I had already wired up setns(2) in the
linux-mips.org tree in commit c3fce54644cabbb90700cc3acc040718a377f609
[MIPS: Wire up new sendmmsg syscall.] but the same syscall numbers were
used by 7b21fddd08 [ns: Wire up the setns
system call] resulting in a conflict.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit ee6114202e48dc282c6d04741e9c5d7171eb8bb8 (lmo) rsp.
1685f3b158 (kernel.org) ["MIPS: SMTC: Move
declaration of smtc_init_secondary to <asm/smtc.h>."] didn't quite do
that - it rather lost the declaration of smtc_init_secondary resulting in
a build error.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
1. support brownstone
2. support mmc
3. support basic filesystem and language
4. remove dynamic_debug, since too many log during access sd
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As suggested by Arnd, move platform data to include/linux/platform_data
in order to improve build coverage for the driver.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Update MMP2 platform code to "sdhci-pxav3", following the driver rename.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-pltfm driver for PXAV3 SoCs, such as MMP2.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Mark F. Brown <mark.brown314@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The rcu callback sn_irq_info_free() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(sn_irq_info_free).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Use plat/regs-fb-v4.h in machine files instead of mach/regs-fb.h.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use plat/regs-fb-v4.h in machine files instead of mach/regs-fb.h.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Use plat/regs-fb-v4.h in machine files instead of mach/regs-fb.h.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDK6410 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDK6450 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDK6440 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDKC100 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDKV210 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDKC210 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for LCD backlight using PWM timer for
Samsung SMDKV310 board.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch creates a common structure for LCD backlight
using PWM timer to be used by various Samsung boards.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Convert the S5PV210/S5P64X0 32-bit down-counting clocksource to
the generic mmio clocksource infrastructure
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the duplicated code for SPDIF ops from S5PV210 and S5PC100.
So, the same can be used in EXYNOS4.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Removes the duplication of default info structure in
dev-i2c[0 ~ 7].c files
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Calls the generic s3c_set_platdata function instead.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is temporary patch for building with clkdev.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
[kgene.kim@samsung.com: removed changes of mach-exynos4/time.c]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The struct clk definition for Samsung platforms is extended to include
a instance of struct clk_lookup and a device name. When clocks are
registered using s3c24xx_register_clock function, the dev_id, con_id
and clk members are initialized with information from the struct clk
instance and struct clk_lookup member is registered.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Bus number 4 doesn't exist in the mainline kernel. The device is
attached to bus number 3. (In the ChromeOS kernel, one of the I2C
busses is split in two with a mux, this pushing all later busses
to a higher bus number. In this case, 4 is the correct bus number
for the ADT7461).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DAP3 is used for a bunch of GPIOs. Not tri-stating the pins means audio
signals get sent out there, and this ends up resetting USB and breaking
SDHCI too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently using just long but this is not enough for the LPAE format
(64-bit entries).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the documented kernel entry requirements are not
explicit about whether the kernel should be entered in ARM or
Thumb, leading to an ambiguitity about how to enter Thumb-2
kernels. As a result, the kernel is reliant on the zImage
decompressor to enter the kernel proper in the correct instruction
set state.
This patch changes the boot entry protocol for head.S and Image to
be the same as for zImage: in all cases, the kernel is now entered
in ARM.
Documentation/arm/Booting is updated to reflect this new policy.
A different rule will be needed for Cortex-M class CPUs as and when
support for those lands in mainline, since these CPUs don't support
the ARM instruction set at all: a note is added to the effect that
the kernel must be entered in Thumb on such systems.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel space needs very little in the way of BTC maintanence as most
mappings which are created and destroyed are non-executable, and so
could never enter the instruction stream.
The case which does warrant BTC maintanence is when a module is loaded.
This creates a new executable mapping, but at that point the pages have
not been initialized with code and data, so at that point they contain
unpredictable information. Invalidating the BTC at this stage serves
little useful purpose.
Before we execute module code, we call flush_icache_range(), which deals
with the BTC maintanence requirements. This ensures that we have a BTC
maintanence operation before we execute code via the newly created
mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.
Tested on EVM with tvp7002 input.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Kernel loadable module can use hard_smp_processor_id() if building with SMP
kernel. In order to make it work for UP kernels too, boot_cpuid_phys
symbol (which is what hard_smp_processor_id() macro resolves to
in non-SMP configuration) must be exported.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now we have the CFAR saved add it to the oops output.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
HFI creates interrupts each time a window is setup. This results in
a lot of messages in the kernel log buffer:
irq: irq 199007 on host null mapped to virtual irq 351
This box has over 3500 of them, causing more important kernel
messages to be overwritten. We can get at this information via
debugfs now so we may as well turn it into a pr_debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As a result of changes to Kconfig files, we no longer enable
the lockup and hung task detectors. Both are very light weight
and provide useful information in the event of a hang, so
reenable them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add mpt2sas driver to pseries and ppc64 defconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The IRQs off tracer enables mcount which has a big impact on
performance. Disable it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The pseries defconfig had a number of drivers enabled and we may
as well add them to the ppc64 defconfig.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Return -EAGAIN when we get H_BUSY back from the hypervisor. This
makes the hvc console driver retry, avoiding dropped printks.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The existing code it pretty ugly. How about we clean it up even more
like this?
From: Anton Blanchard <anton@samba.org>
We check for timeout expiry in the outer loop, but we also need to
check it in the inner loop or we can lock up forever waiting for a
CPU to hit real mode.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: <stable@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 32bit platforms that support >= 4GB memory total_ram was truncated.
This creates a confusing printk:
Top of RAM: 0x100000000, Total RAM: 0x0
Fix that:
Top of RAM: 0x100000000, Total RAM: 0x100000000
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes the following warning:
WARNING: arch/powerpc/kernel/built-in.o(.text+0x29768): Section mismatch in reference from the function .register_power_pmu() to the function .cpuinit.text:.power_pmu_notifier()
The function .register_power_pmu() references
the function __cpuinit .power_pmu_notifier().
This is often because .register_power_pmu lacks a __cpuinit
annotation or the annotation of .power_pmu_notifier is wrong.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The address limit is already set in flush_old_exec() so this
set_fs(USER_DS) is redundant.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Singleton calls seem to end up being pretty common, so just
directly call the hypercall rather than going via multicall.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
It's useful - and probably should be a config - but its very heavyweight,
especially with the tracing stuff to help sort out problems.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Make sure the fastpath code is inlined. Batch the page permission change
and the pin/unpin, and make sure that it can be batched with any
adjacent set_pte/pmd/etc operations.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
During the refactoring of the Orion MPP code, the detection for
the 5181l as been used to select the 5181 MPP mask, which is wrong.
Select the 5181 mask for all 5181 variants.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Now that 1b3f2a72bb is in, it is very
important that the below lying comment be removed! :-)
Signed-off-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/20110718191054.GA18359@liondog.tnic
Acked-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Having this value defined at compile time prevents multiple machines with
conflicting definitions to coexist. Move it to a variable in preparation
for having a per machine value selected at run time. This is relevant
only when CONFIG_ZONE_DMA is selected.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This was introduced more than 3 years ago, and since then only generic
janitorial changes were made without further addition of actual support
for "real" devices. This is therefore a cost with no benefits to keep
in the tree. If someone wishes to revive this code, it is always
possible to retrieve it from the Git repository.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
CC: Ke Wei <kewei@marvell.com>
CC: Saeed Bishara <saeed@marvell.com>
CC: Lennert Buytenhek <buytenh@wantstofly.org>
On Tue, 28 Jun 2011, Ben Dooks wrote:
> On Tue, Jun 28, 2011 at 11:22:57PM +0200, Arnd Bergmann wrote:
>
> > On a related note, what about mach-s3c2400? It seems to be even more
> > incomplete.
>
> Probably the same fate awaits that. It is so old that there's little
> incentive to do anything with it.
So out it goes as well.
The PORT_S3C2400 definition in include/linux/serial_core.h is left there
to prevent a reuse of the same number for another port type.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Commit bcae8aeb32 "[ARM] S3C24A0: Initial architecture support files"
brought in a bunch of files while explicitly leaving out the corresponding
Kconfig entry, stating that the series is not complete.
More than 2.5 years later, the support for this has not seen any progress.
This is therefore dead code. If someone wants to revive this code, it is
always possible to retrieve it from the Git repository.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: DMA Cleanup as per sparse
ARM: SAMSUNG: Check NULL return from irq_alloc_generic_chip
This shift instruction appears to be shifting in the wrong direction.
Without this change, my SparcStation-20MP hangs just after bringing up
the second CPU:
Entering SMP Mode...
Starting CPU 2 at f02b4e90
Brought up 2 CPUs
Total of 2 processors activated (99.52 BogoMIPS).
*** stuck ***
Signed-off-by: Will Simoneau <simoneau@ele.uri.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function declaration differs between file: dma.c and file:dma.h
and SPARSE (Documentation/sparse.txt) gives error messages
All dma channels are members of 'enum dma_ch' and not 'unsigned int'
Please have a look at channel definitions in:
arch/arm/mach-s3c64xx/include/mach/dma.h
arch/arm/plat-samsung/include/plat/s3c-dma-pl330.h
arch/arm/mach-s3c2410/include/mach/dma.h
So all arguments should be of type 'enum dma_ch'
Signed-off-by: Sangwook Lee <sangwook.lee@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 234b6ceddb
clocksource: convert ARM 32-bit up counting clocksources
broke the build for ixp4xx and made big endian operation impossible.
This commit restores the original behaviour.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
[ Thomas says that we might want to have generic BE accessor functions
to the MMIO clock source, but that hasn't happened yet, so in the
meantime this seems to be the short-term fix for the particular
problem - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code in arch/mips/kernel/i8259.c still hasn't been converted to
using struct syscore_ops instead of a sysdev for resume and shutdown.
As a result, this code doesn't build any more after suspend, resume
and shutdown callbacks have been removed from struct sysdev_class.
Fix this problem by converting i8259.c to using syscore_ops.
Reported-and-tested-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
As promised in feature-removal-schedule.txt it is time to
remove the nfsctl system call.
Userspace has perferred to not use this call throughout 2.6 and it has been
excluded in the default configuration since 2.6.36 (9 months ago).
So this patch removes all the code that was being compiled out.
There are still references to sys_nfsctl in various arch systemcall tables
and related code. These should be cleaned out too, probably in the next
merge window.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Fix the printk_once() so that it actually prints (didn't print before
due to a stray comma.)
[ hpa: changed to an incremental patch and adjusted the description
accordingly. ]
Signed-off-by: Len Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1107151732480.18606@x980
Cc: <table@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
* pm-domains: (33 commits)
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
PM / Domains: Make failing pm_genpd_prepare() clean up properly
PM / Domains: Set device state to "active" during system resume
ARM: mach-shmobile: sh7372 A3RV requires A4LC
PM / Domains: Export pm_genpd_poweron() in header
ARM: mach-shmobile: sh7372 late pm domain off
ARM: mach-shmobile: Runtime PM late init callback
ARM: mach-shmobile: sh7372 D4 support
ARM: mach-shmobile: sh7372 A4MP support
ARM: mach-shmobile: sh7372: make sure that fsi is peripheral of spu2
ARM: mach-shmobile: sh7372 A3SG support
...
Other files using dma.h may fail to compile as follows:
In file included from sound/soc/mxs/mxs-pcm.h:22,
from sound/soc/mxs/mxs-saif.h:112,
from sound/soc/mxs/mxs-sgtl5000.c:34:
arch/arm/mach-mxs/include/mach/dma.h:16: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbh':
arch/arm/mach-mxs/include/mach/dma.h:18: error: dereferencing pointer to incomplete type
arch/arm/mach-mxs/include/mach/dma.h: At top level:
arch/arm/mach-mxs/include/mach/dma.h:21: warning: 'struct dma_chan' declared inside parameter list
arch/arm/mach-mxs/include/mach/dma.h: In function 'mxs_dma_is_apbx':
arch/arm/mach-mxs/include/mach/dma.h:23: error: dereferencing pointer to incomplete type
make[3]: *** [sound/soc/mxs/mxs-sgtl5000.o] Error 1
make[2]: *** [sound/soc/mxs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
It seems it's better for dma.h to include dmaengine.h himself.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If both the RTS pad and CTS pad definitions setup
IOMUXC_UARTn_IPP_UART_RTS_MUX_SELECT_INPUT, then
the order of setup will matter. We don't want that.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
If both the RXD pad and TXD pad definitions setup
IOMUXC_UARTn_IPP_UART_RXD_MUX_SELECT_INPUT, then
the order of setup will matter. We don't want that.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The I2C controller requires the SION bit to be set on SDA and SCL pins.
This is missing on some pad definitions for the I2C function.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
handle_signal()->set_fs() has a nice comment which explains what
set_fs() is, but it doesn't explain why it is needed and why it
depends on CONFIG_X86_64.
Afaics, the history of this confusion is:
1. I guess today nobody can explain why it was needed
in arch/i386/kernel/signal.c, perhaps it was always
wrong. This predates 2.4.0 kernel.
2. then it was copy-and-past'ed to the new x86_64 arch.
3. then it was removed from i386 (but not from x86_64)
by b93b6ca3 "i386: remove unnecessary code".
4. then it was reintroduced under CONFIG_X86_64 when x86
unified i386 and x86_64, because the patch above didn't
touch x86_64.
Remove it. ->addr_limit should be correct. Even if it was possible
that it is wrong, it is too late to fix it after setup_rt_frame().
Linus commented in:
http://lkml.kernel.org/r/alpine.LFD.0.999.0707170902570.19166@woody.linux-foundation.org
... about the equivalent bit from i386:
Heh. I think it's entirely historical.
Please realize that the whole reason that function is called "set_fs()" is
that it literally used to set the %fs segment register, not
"->addr_limit".
So I think the "set_fs(USER_DS)" is there _only_ to match the other
regs->xds = __USER_DS;
regs->xes = __USER_DS;
regs->xss = __USER_DS;
regs->xcs = __USER_CS;
things, and never mattered. And now it matters even less, and has been
copied to all other architectures where it is just totally insane.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710164424.GA20261@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
1. do_signal() looks at TS_RESTORE_SIGMASK and calculates the
mask which should be stored in the signal frame, then it
passes "oldset" to the callees, down to setup_rt_frame().
This is ugly, setup_rt_frame() can do this itself and nobody
else needs this sigset_t. Move this code into setup_rt_frame.
2. do_signal() also clears TS_RESTORE_SIGMASK if handle_signal()
succeeds.
We can move this to setup_rt_frame() as well, this avoids the
unnecessary checks and makes the logic more clear.
3. use set_current_blocked() instead of sigprocmask(SIG_SETMASK),
sigprocmask() should be avoided.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710182203.GA27979@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
sys_sigsuspend() and sys_sigreturn() change ->blocked directly.
This is not correct, see the changelog in e6fa16ab
"signal: sigprocmask() should do retarget_shared_pending()"
Change them to use set_current_blocked().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710192727.GA31759@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
sys32_sigsuspend() and sys32_*sigreturn() change ->blocked directly.
This is not correct, see the changelog in e6fa16ab
"signal: sigprocmask() should do retarget_shared_pending()"
Change them to use set_current_blocked().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20110710192724.GA31755@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now that clocksource.archdata is available, use it for ia64-specific
code.
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: linux-ia64@vger.kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/d31de0ee0842a0e322fb6441571c2b0adb323fa2.1310563276.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fix a trivial typo in the name of the constant
ENERGY_PERF_BIAS_POWERSAVE. This didn't cause trouble because this
constant is not currently used for anything.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Len Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/r/tip-abe48b108247e9b90b4c6739662a2e5c765ed114@git.kernel.org
Remove wrong setting of dev->flags. NETIF_F_NO_CSUM maps to IFF_DEBUG
there, so looks like a mistake.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hw_nmi_watchdog_set_attr() weak function
and appropriate x86_pmu::hw_watchdog_set_attr() call
we introduce even alias mechanism which allow us
to drop this routines completely and isolate quirks
of Netburst architecture inside P4 PMU code only.
The main idea remains the same though -- to allow
nmi-watchdog and perf top run simultaneously.
Note the aliasing mechanism applies to generic
PERF_COUNT_HW_CPU_CYCLES event only because arbitrary
event (say passed as RAW initially) might have some
additional bits set inside ESCR register changing
the behaviour of event and we can't guarantee anymore
that alias event will give the same result.
P.S. Thanks a huge to Don and Steven for for testing
and early review.
Acked-by: Don Zickus <dzickus@redhat.com>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
CC: Ingo Molnar <mingo@elte.hu>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Stephane Eranian <eranian@google.com>
CC: Lin Ming <ming.m.lin@intel.com>
CC: Arnaldo Carvalho de Melo <acme@redhat.com>
CC: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20110708201712.GS23657@sun
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Software defined version number is not stable enough to be used
in device type naming scheme. The patch changes it to use implicit
soc name for spi device type definition. In this way, we can easily
align the naming scheme with device tree binding, which comes later.
It removes fifosize from spi_imx_data and adds devtype there, so that
fifosize can be set in an inline function according to devtype.
Also, cpu_is_mx can be replaced by inline functions checking devtype.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since 2.6.36 (23016bf0d2), Linux prints the existence of "epb" in /proc/cpuinfo,
Since 2.6.38 (d5532ee7b4), the x86_energy_perf_policy(8) utility has
been available in-tree to update MSR_IA32_ENERGY_PERF_BIAS.
However, the typical BIOS fails to initialize the MSR, presumably
because this is handled by high-volume shrink-wrap operating systems...
Linux distros, on the other hand, do not yet invoke x86_energy_perf_policy(8).
As a result, WSM-EP, SNB, and later hardware from Intel will run in its
default hardware power-on state (performance), which assumes that users
care for performance at all costs and not for energy efficiency.
While that is fine for performance benchmarks, the hardware's intended default
operating point is "normal" mode...
Initialize the MSR to the "normal" by default during kernel boot.
x86_energy_perf_policy(8) is available to change the default after boot,
should the user have a different preference.
Signed-off-by: Len Brown <len.brown@intel.com>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1107140051020.18606@x980
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@kernel.org>
Since the A4LC should only be powered off if the A3RV is off, make
the A4LC's power down routine return -EBUSY if A3RV is not off to
indicate to the core that it doesn't want to power off the domain in
that case. This will cause the core to regard A4LC as active, so
the pm_genpd_poweron() in pd_power_down_a3rv() is not necessary any
more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
Make pd_power_down_a3rv() use genpd_queue_power_off_work() to queue
up the powering off of the A4LC domain to avoid queuing it up when
it is pending.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Magnus Damm <damm@opensource.se>
This patch makes update_rq_clock() aware of steal time.
The mechanism of operation is not different from irq_time,
and follows the same principles. This lives in a CONFIG
option itself, and can be compiled out independently of
the rest of steal time reporting. The effect of disabling it
is that the scheduler will still report steal time (that cannot be
disabled), but won't use this information for cpu power adjustments.
Everytime update_rq_clock_task() is invoked, we query information
about how much time was stolen since last call, and feed it into
sched_rt_avg_update().
Although steal time reporting in account_process_tick() keeps
track of the last time we read the steal clock, in prev_steal_time,
this patch do it independently using another field,
prev_steal_time_rq. This is because otherwise, information about time
accounted in update_process_tick() would never reach us in update_rq_clock().
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Eric B Munson <emunson@mgebm.net>
CC: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
CC: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since in a later patch I intend to call jump labels inside
CONFIG_PARAVIRT, IA64 would fail to compile if they are not
provided. This patch provides those jump labels for the IA64
architecture.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
Acked-by: Rik van Riel <riel@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Eddie Dong <eddie.dong@intel.com>
CC: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Anthony Liguori <aliguori@us.ibm.com>
CC: Eric B Munson <emunson@mgebm.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds a function pointer in one of the many paravirt_ops
structs, to allow guests to register a steal time function. Besides
a steal time function, we also declare two jump_labels. They will be
used to allow the steal time code to be easily bypassed when not
in use.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Acked-by: Rik van Riel <riel@redhat.com>
Tested-by: Eric B Munson <emunson@mgebm.net>
CC: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
To implement steal time, we need the hypervisor to pass the guest
information about how much time was spent running other processes
outside the VM, while the vcpu had meaningful work to do - halt
time does not count.
This information is acquired through the run_delay field of
delayacct/schedstats infrastructure, that counts time spent in a
runqueue but not running.
Steal time is a per-cpu information, so the traditional MSR-based
infrastructure is used. A new msr, KVM_MSR_STEAL_TIME, holds the
memory area address containing information about steal time
This patch contains the hypervisor part of the steal time infrasructure,
and can be backported independently of the guest portion.
[avi, yongjie: export delayacct_on, to avoid build failures in some configs]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Tested-by: Eric B Munson <emunson@mgebm.net>
CC: Rik van Riel <riel@redhat.com>
CC: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Yongjie Ren <yongjie.ren@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
According to discussion of the ARM arch subsystem migration,
ARM cpufreq drivers move to drivers/cpufreq. So this patch
adds Kconfig.arm for ARM like x86 and adds Samsung S5PV210
and EXYNOS4210 cpufreq driver compile in there.
As a note, otherw will be moved.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This is a straight code motion patch, there are no changes to the driver
itself. The Kconfig is left untouched as the ARM CPUfreq Kconfig is all
in one big block in arm/Kconfig and should be moved en masse rather than
being done piecemeal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The vread field was bloating struct clocksource everywhere except
x86_64, and I want to change the way this works on x86_64, so let's
split it out into per-arch data.
Cc: x86@kernel.org
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: linux-ia64@vger.kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/3ae5ec76a168eaaae63f08a2a1060b91aa0b7759.1310563276.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Three fixes here:
- Send SIGSEGV if called from compat code or with a funny CS.
- Don't BUG on impossible addresses.
- Add a missing local_irq_disable.
This patch also removes an unused variable.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Link: http://lkml.kernel.org/r/6fb2b13ab39b743d1e4f466eef13425854912f7f.1310563276.git.luto@mit.edu
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
These occur extremely rarely in the kernel and writing test cases for
them is difficult.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These use the register calling conventions required by the new decoding
table framework for calling simulated instructions.
We rename the old versions of these functions to *_old for now.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is the emulation function for the instruction format used by the
ARM multiply long instructions. It replaces use of
prep_emulate_rdhi16rdlo12rs8rm0_wflags().
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is the emulation function for the instruction format used by the
ARM bit-field manipulation instructions.
Various other instruction forms can also make use of this and it is used
to replace use of prep_emulate_rd12{rm0}{_modify}
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is the emulation function for the instruction format used by the
ARM multiply-accumulate instructions. These don't allow use of PC so we
don't have to add special cases for this.
This function is used to replace use of prep_emulate_rd16rs8rm0_wflags
and prep_emulate_rd16rn12rs8rm0_wflags.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is the emulation function for the instruction format used by the
ARM media instructions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is an emulation function for the LDRD and STRD instructions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is the emulation function for the instruction format used by the
ARM data-processing instructions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This is for use by inline assembler which will be added to kprobes-arm.c
It saves memory when used on newer ARM architectures and also provides
correct interworking should ARM probes be required on Thumb kernels in
the future.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This writes a new value to PC which was obtained as the result of an ARM
ALU instruction. For ARMv7 and later this performs interworking.
On ARM kernels we shouldn't encounter any ALU instructions trying to
switch to Thumb mode so support for this isn't strictly necessary.
However, the approach taken in all other instruction decoding is for us
to avoid unpredictable modification of the PC for security reasons. This
is usually achieved by rejecting insertion of probes on problematic
instruction, but for ALU instructions we can't do this as it depends on
the contents of the CPU registers at the time the probe is hit. So, as
we require some form of run-time checking to trap undesirable PC
modification, we may as well simulate the instructions correctly, i.e.
in the way they would behave in the absence of a probe.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
We will reject probing of unprivileged load and store instructions.
These rarely occur and writing test cases for them is difficult.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
