Observed crash when module is unloaded if CONFIG_RSI_DEBUGSFS is not set.
Fix: Debugfs entry removal moved inside CONFIG_RSI_DEBUGSFS flag in
function rsi_mac80211_detach()
Memory leak found and fixed for below structures in function rsi_mac80211_detach()
* channel list for each supported band
* rsi debugfs info
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When in AP mode, scans can be done without changing firmware to
the multi-role firmware. Allow the interface to scan if forced
in the scan request.
Signed-off-by: James Minor <james.minor@ni.com>
Signed-off-by: Xander Huff <xander.huff@ni.com>
Reviewed-by: Ben Shelton <ben.shelton@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register the WLAN device as a wakeup source since it can
wake the system via wake-on-wireless-lan. In an actual wowlan
event, notify the PM core that we are the current wakeup source.
This allows the PM core to update the wakeup attributes in /sys.
This was causing wakeup issues on chromeos as the system was
apparently confused about the wakeup source.
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Reviewed-by: Eric Caruso <ejcaruso@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This event is used by the Firmware to limit the RX BA win size
for a specific link.
The event handler updates the new size in the mac's sta->sta struct.
BA sessions opened for that link will use the new restricted
win_size. This limitation remains until a new update is received or
until the link is closed.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a new BA session, we must pass the win_size to the FW.
To do this we take max_rx_aggregation_subframes (BA RX win size)
which is stored in ieee80211_sta structure (e.g per link and not per HW)
We will use the value stored per link when passing the win_size to
firmware through the ACX_BA_SESSION_RX_SETUP command.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The word "background" contains 10 characters so the third argument of
strncmp() need to be 10 in order to match this prefix correctly.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Fixes: 855aed1220 ("ath10k: add spectral scan feature")
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove extraneous error message in 'ath10k_htt_tx_alloc_cont_frag_desc'
as the caller 'ath10k_htt_tx_alloc' already dumps a proper error
message
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cleanup 'ath10k_htt_tx_alloc' by introducing the API's
'ath10k_htt_tx_alloc/free_{cont_txbuf, txdone_fifo} and
re-use them whereever needed
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This partially reverts 'commit 2cdce425aa
("ath10k: Fix broken NULL func data frame status for 10.4")'
Unfortunately this breaks sending NULL func and the existing
issue of obtaining proper tx status for NULL function will be
fixed. Also update the comments for feature flag added to be
useless and not working
Fixes: 2cdce425aa "ath10k: Fix broken NULL func data frame status for
10.4"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This switches ath9k over to using the mac80211 intermediate software
queueing mechanism for data packets. It removes the queueing inside the
driver, except for the retry queue, and instead pulls from mac80211 when
a packet is needed. The retry queue is used to store a packet that was
pulled but can't be sent immediately.
The old code path in ath_tx_start that would queue packets has been
removed completely, as has the qlen limit tunables (since there's no
longer a queue in the driver to limit).
The mac80211 intermediate software queues offer significant latency
reductions, and this patch allows ath9k to realise them. The exact gains
from this varies with the test scenario, but in an access point scenario
we have seen latency reductions ranging from 1/3 to as much as an order
of magnitude. We also achieve slightly better aggregation.
Median latency (ping) figures with this patch applied at the access point,
with two high-rate stations and one low-rate station (HT20 5Ghz), running
a Flent rtt_fair_var_up test with one TCP flow and one ping flow going to
each station:
Fast station Slow station
Default pfifo_fast qdisc: 430.4 ms 638.7 ms
fq_codel qdisc on iface: 35.5 ms 211.8 ms
This patch set: 22.4 ms 38.2 ms
Median aggregation sizes over the same test:
Default pfifo_fast qdisc: 9.5 pkts 1.9 pkts
fq_codel qdisc on iface: 11.2 pkts 1.9 pkts
This patch set: 13.9 pkts 1.9 pkts
This patch is based on Tim's original patch set, but reworked quite
thoroughly.
Cc: Tim Shepard <shep@alum.mit.edu>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add missing space in a dev_err message and join wrapped text so
it does not span multiple lines. Fix spelling mistake on "unknown".
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows setting the MAC address and specifying that the firmware
will be requested from userspace (because there might not be a hardware
EEPROM connected to the chip) for ath9k based PCI devices using
the device tree.
There is some out-of-tree code to "convert devicetree to
ath9k_platform_data" (for example in OpenWrt and LEDE) which becomes
obsolete with this patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be used when the ath_bus_type has to be presented in a log
message or firmware filename.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit
0f9edcdd88 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.
I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.
This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.
With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.
While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.
Fixes: 0f9edcdd88 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.")
Cc: <stable@vger.kernel.org> #4.7+
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Due to the cast from uint32_t to int64_t, a wrong next beacon timing is
calculated and effectively the beacon timer stops working. This is
especially bad for 802.11s mesh networks, because discovery breaks
without beacons.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to krealloc() in wsm_buf_reserve() directly assigns the newly
returned memory to buf->begin. This is all fine except when krealloc()
failes we loose the ability to free the old memory pointed to by
buf->begin. If we just create a temporary variable to assign memory to
and assign the memory to it we can mitigate the memory leak.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the missing destroy_workqueue() before return from
mwifiex_add_virtual_intf() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Marvell p2p device disappears from the list of p2p peers on the other
p2p device after disconnection.
It happens due to a bug in driver. When interface is changed from p2p
to station, certain variables(bss_type, bss_role etc.) aren't correctly
updated. This patch corrects them to fix the issue.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that if single tid 6 packet comes among with massive tid 0
packets, tid 6 packet may stay in it's queue and will never be
transmited. This is because wmm.highest_queued_prio will be set to 2
during transmission of tid 0 packets As a result, main work thread
keeps on looping without serving that packet. In this case, if command
has downloaded to firmware, driver doesn't process it's response causing
command timeout.
This patch will reset highest_queued_prio if packets exist in data
queue, and try to find a ra_list for current private.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wmm.tx_pkts_queued and ralist's total_pkt_count should be updated in
synchronization. They were not correctly updated in
mwifiex_send_processed_packet().
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for this debugfs command is available in driver. This patch
adds usage information in README file.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While copying the vendor_ie obtained from the cfg80211_find_vendor_ie()
to the struct mwifiex_types_wmm_info, length/size was inappropriate.
This patch corrects the required length needed to the
mwifiex_types_wmm_info
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At couple of places in cleanup path, we are just going through the
skb queue and freeing them without unlinking. This leads to a crash
when other thread tries to do skb_dequeue() and use already freed node.
The problem is freed by unlinking skb before freeing it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When host_sleep_config command fails, we should return an error to
PCIe, instead of continuing (and possibly panicking, when we try to keep
processing a timed-out ioctl after we return "successfully" from
suspend).
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Following is mwifiex driver-firmware host sleep handshake.
It involves three threads. suspend handler, interrupt handler, interrupt
processing in main work queue.
1) Enter suspend handler
2) Download HS_CFG command
3) Response from firmware for HS_CFG
4) Suspend thread waits until handshake completes(i.e hs_activate becomes
true)
5) SLEEP from firmware
6) SLEEP confirm downloaded to firmware.
7) SLEEP confirm response from firmware
8) Driver processes SLEEP confirm response and set hs_activate to wake up
suspend thread
9) Exit suspend handler
10) Read sleep cookie in loop and wait until it indicates firmware is
sleep.
11) After processing SLEEP confirm response, we are at the end of interrupt
processing routine. Recheck if there are interrupts received while we were
processing them.
During suspend-resume stress test, it's been observed that we may end up
acessing PCIe hardware(in 10 and 11) when PCIe bus is closed which leads
to a kernel crash.
This patch solves the problem with below changes.
a) action 10 above can be done before 8
b) Skip 11 if hs_activated is true. SLEEP confirm response
is the last interrupt from firmware. No need to recheck for
pending interrupts.
c) Add flush_workqueue() in suspend handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far our core code was calling brcmf_fws_process_skb which wasn't
a proper thing to do. If case of devices using msgbuf protocol fwsignal
shouldn't be used. It was an unnecessary extra layer simply calling
a protocol specifix txdata function.
Please note we already have txdata callback, but it's used for calls
between bcdc and fwsignal so it couldn't be simply used there.
This makes core code more generic (instead of bcdc/fwsignal specific).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some devices the EEPROMs of Ralink Wi-Fi chips have a default Ralink
MAC address set (RT3062F: 00:0C:43:30:62:00, RT3060F:
00:0C:43:30:60:00). Using multiple of these devices in the same network
can cause nasty issues.
Allow to override the MAC in the EEPROM with (a known good) one set in
the device tree to bypass the issue.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.10. Major changes:
ath10k
* allow setting coverage class for first generation cards
* read regulatory domain from ACPI
ath9k
* disable RNG by default
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
-----BEGIN PGP SIGNATURE-----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=SjfQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Among various cleanups and improvements, we have the following:
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now genl_register_family() is the only thing (other than the
users themselves, perhaps, but I didn't find any doing that)
writing to the family struct.
In all families that I found, genl_register_family() is only
called from __init functions (some indirectly, in which case
I've add __init annotations to clarifly things), so all can
actually be marked __ro_after_init.
This protects the data structure from accidental corruption.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Use dev_coredumpmsg() to prevent locking the driver;
* Small fix to pass the AID to the FW;
* Use FW PS decisions with multi-queue;
-----BEGIN PGP SIGNATURE-----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=D+eo
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-10-25-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Finalize and enable dynamic queue allocation;
* Use dev_coredumpmsg() to prevent locking the driver;
* Small fix to pass the AID to the FW;
* Use FW PS decisions with multi-queue;
A bugfix added a sanity check around the assignment and use of the
'is_11d' variable, which looks correct to me, but as the function is
rather complex already, this confuses the compiler to the point where
it can no longer figure out if the variable is always initialized
correctly:
brcm80211/brcmfmac/cfg80211.c: In function ‘brcmf_cfg80211_start_ap’:
brcm80211/brcmfmac/cfg80211.c:4586:10: error: ‘is_11d’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds an initialization for the newly introduced case in which
the variable should not really be used, in order to make the warning
go away.
Fixes: b3589dfe02 ("brcmfmac: ignore 11d configuration errors")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* a fix for a false-positive lockdep report;
* a fix for multi-queue that caused an unnecessary 1 second latency;
* a fix for an ACPI parsing bug that caused a misleading error message;
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYDyZmAAoJEKFHnKIaPMX6ruIQALv56HIAEQ1pfx0JXyignOXL
I1dc7cnuVUaQTV8RoYw57SXcY8JOZe0Dx8s8sA5tT0MG0mYtImX7gxlAhzdKL1WR
EsXhw5/veg+7C7JrXAGbimOZnHg6oEmDrLX5KVXlKfxXbGHBUc8T70zG6ooHuEx8
IBaIjVjSTxeqscHVkDOUOfD5Shf/o0Fqrf1j9WtirODwhyUTz1U48xZRFPGDAUiW
8wJyEoF/AyJp1wnUc6QwWrW/JfLhXO3jpUoF1Y20/zpV+Hb+BjIoYhoPbyZApfCn
H4e1R0KTpd0pBbpKosgSXrX2EmJcZ80brfyfffJV8ZrQ6PILI60cXBHBjyDBYwic
wzry57a7lLNSWjQBRmbLLlFOF7H8eVo6kQnxsFpJFH8uTbIb0tQaQZ1PUiG6HZSO
h63emZLZFTR6ZxftYf+Kf3jFBCfeR1BxheFPBwQmPAoVfvEdeOo7gqhpnWs7AKFx
xkic/BdEOx2geyVnDJxELo5SdCzjbYDxCK8F6gM414w0UAMM/arknmreYuzU+/gD
zSRUAwFatoriEXJhLEvIZH4oyYzDsUFo6ATqkJZlVPH7+Lc7beZQRQ4c7iQUCGYq
86Hke/7Hwk4hoO6tQXHhesQCErc4jqMI4cP654QSqXnB9oT2lF2qXzukHKrsDVhV
1g1Mz5cgzbj26jZjq0P7
=gXgM
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2015-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* some fixes for suspend/resume with unified FW images;
* a fix for a false-positive lockdep report;
* a fix for multi-queue that caused an unnecessary 1 second latency;
* a fix for an ACPI parsing bug that caused a misleading error message;
The old WDS 4-addr frame support is very limited, e.g.
* no encryption is possible on such links
* it cannot support rate/HT/VHT negotiation
* management APIs are very restricted
These make the WDS legacy mode useless in practice.
All of these are resolved by the 4-addr AP/client support,
so there's also no reason to improve WDS in the future.
Therefore, add a Kconfig option to disable legacy WDS.
This gives people an "emergency valve" while they migrate
to the better-supported 4-addr AP/client option; we plan
to remove it (and the associated cfg80211/mac80211 code,
which is the ultimate goal) in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwlmvm currently uses dev_coredumpm() to collect multiple
buffers, but this has the downside of pinning the module
until the coredump expires, if the data isn't read by any
userspace.
Avoid this by using the new dev_coredumpsg() method. We
still copy the data from the old way of generating it, but
neither hold on to vmalloc'ed data for a long time, nor do
we pin the module now.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New firmwares support dynamic queue allocation (DQA), which enables
on-demand allocation of queues per RA/TID, instead of allocating them
statically per vif. This allows an AP to send, for instance, BE
traffic to STA2 even if it also needs to send traffic to a sleeping
STA1, without being blocked by the sleeping station.
The implementation in the driver is now ready, so we can enable this
feature by default when running firmwares that support it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
[reworded the commit message]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mac80211 determines whether HW does fragmentation
by checking whether the set_frag_threshold callback is set
or not.
However, some drivers may want to set the HW fragmentation
capability depending on HW generation.
Allow this by checking a HW flag instead of checking the
callback.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
[added the flag to ath10k and wlcore]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently when configuring the cab queue the scheduler is configured
without station id - which results in station id 0.
In DQA mode this causes firmware to assert later on when the actual
station 0 is added with an empty tfd_queue_mask.
Fix that by configuring the queue to the broadcast station.
This is a bit trickier since the queue should not be included in the
tfd_queue_mask of the ADD_STA since it is a multicast queue, and the
tfd_queue_mask is only unicast queue. As a result the queue should be
enabled only after the broadcast station is added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a peer associates, the firmware will soon want to know
its AID to be able to compute the TIM IE by itself.
In DQA, the firmware has all the information it needs to
update the TIM internally. The only missing part is the
AID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of passing DRV_NAME pass a string that
represents the reason for the interrupt.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When using RSS on 9000 series devices, we can't rely on processing the
received frames for station powersave handling, since they could be
processed on different CPUs and out of order.
In order to still manage the powersave of stations, the firmware sends
a notification on sleep->wake, wake->sleep and - for U-APSD - frames
received with PM while already sleeping (with the TID.)
With this, the driver can set AP_LINK_PS, which is required for real
parallel RX. In addition, this requires checking for PS-Poll frames
and calling ieee80211_sta_pspoll() appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a STA has deferred traffic to TX, an appropriate bit
is turned on in %deferred_tx_frames to indicate deferred
traffic. This marking is never turned off, resulting in
iterating over TIDs with no deferred traffic.
Although this didn't cause any failures/errors/bugs, there
is still no point of iterating over these TIDs when not
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the TXQs are allocated on demand, so make
sure the sniffer STA tfd_queue_msk isn't set.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a TXQ's marking as a reserved queue is removed,
when removing the STA the driver might try to access
out of bounds memory. Make sure the reserved queue
is freed only if it is still reserved.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a TXQ's owner is changed, the FW is indeed notified, but
the driver doesn't update the current metadata to reflect the
owner change. Fix that.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With unified images, we need to make sure the net-detect scan is
stopped after resuming, since we don't restart the FW. Also, we need
to make sure we check if there are enough scan slots available to run
it, as we do with other scans.
Fixes: commit 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The SPLC data parsing is too restrictive and was not trying find the
correct element for WiFi. This causes problems with some BIOSes where
the SPLC method exists, but doesn't have a WiFi entry on the first
element of the list. The domain type values are also incorrect
according to the specification.
Fix this by complying with the actual specification.
Additionally, replace all occurrences of SPLX to SPLC, since SPLX is
only a structure internal to the ACPI tables, and may not even exist.
Fixes: bcb079a14d ("iwlwifi: pcie: retrieve and parse ACPI power limitations")
Reported-by: Chris Rorvick <chris@rorvick.com>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Tested-by: Chris Rorvick <chris@rorvick.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we sync the RX queues the driver waits to receive echo
notification on all the RX queues.
The wait queue is set with timeout until all queues have received
the notification.
However, iwl_mvm_rx_queue_notif() never woke up the wait queue,
with the result of the counter value being checked only when the
timeout expired.
This may cause a latency of up to 1 second.
Fixes: 0636b93821 ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the suspend flow fails, we restart the hardware to go back to
the D0 image (with non-unified images), but we don't comply with
the fw_restart module parameter. If something goes wrong when
starting the D3 image, we may want to debug it, so we should
comply with the fw_restart flag to avoid clearing everything up
and losing the firmware state when the error occurred.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a unified D0/D3 image is used, we don't restart the FW in the
D0->D3->D0 transitions. Therefore, the d3_test functionality should
not call ieee8021_restart_hw() when the resuming either.
Fixes: commit 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_dbgfs_mem_read(), the len variable may become negative and is
compared to < 0 (an error case). Comparing size_t (which is unsigned)
to < 0 causes a warning on certain platforms (like i386):
drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c:1561:5-8: WARNING: Unsigned expression compared with zero: len < 0
To prevent that, use ssize_t for len instead.
Fixes: commit 2b55f43f8e ("iwlwifi: mvm: Add mem debugfs entry")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Emmanuel reports that when CMD_WANT_ASYNC_CALLBACK is used by mvm,
the callback will be called with the command queue lock held, and
mvm will try to stop all (other) TX queues, which acquires their
locks - this caused a false lockdep recursive locking report.
Suppress this report by marking the command queue lock with a new,
separate, lock class so lockdep can tell the difference between
the two types of queues.
Fixes: 156f92f2b4 ("iwlwifi: block the queues when we send ADD_STA for uAPSD")
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
from stack removal fix that crashes things when VMAP
stack is used in conjunction with software crypto.
Aside from that, we have:
* a fix for AP_VLAN usage with the nl80211 frame command
* two fixes (and two preparation patches) for A-MSDU, one
to discard group-addressed (multicast) and unexpected
4-address A-MSDUs, the other to validate A-MSDU inner
MAC addresses properly to prevent controlled port bypass
-----BEGIN PGP SIGNATURE-----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=T6t1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-10-18' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
This is relatively small, mostly to get the SG/crypto
from stack removal fix that crashes things when VMAP
stack is used in conjunction with software crypto.
Aside from that, we have:
* a fix for AP_VLAN usage with the nl80211 frame command
* two fixes (and two preparation patches) for A-MSDU, one
to discard group-addressed (multicast) and unexpected
4-address A-MSDUs, the other to validate A-MSDU inner
MAC addresses properly to prevent controlled port bypass
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
wlcore
* fix a double free regression causing hard to track crashes
rtl8xxxu
* fix driver reload issues, a memory leak and an endian bug
rtlwifi
* fix a major regression introduced in 4.9 with firmware loading on
certain hardware
ath10k
* fix regression about broken cal_data debugfs file (since 4.7)
ath9k
* revert temperature compensation for AR9003+ devices, it was causing
too much problems
ath6kl
* add Dell OEM SDIO I/O for the Venue 8 Pro
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYAIKDAAoJEG4XJFUm622b7IcH/iV/mLuZ0Nyh7tsNeSElTjVc
AEFUdcxVRjM96n9K8AcHZVFqCSMggibOgulGiwHO48DLWOhOdzhffn3GZaRbHTbL
5o3d527R1kvx+UP8KIFF5MHjagMEC3/AYi417/DiCGH0BM6UcFPFxXOOWePiG0ov
Lz14xi/8AUrOnREc3TzvDsRUaI2VO3vvXq+IQtMwQBmtczeaKwjjw/RsqkCdkD70
yqiZVO7FJ3mDH1ybxmkbhlAklG7p9x01e3+gRbnKdEqYiaoYUrRGNE5wq00fuFBU
Xa3vbQa22csD2ShGHtPnZ6kg4X/q2gLmxNWl6M5TVvwUVD313AQepIcnTiHnwro=
=TI3A
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-10-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.9
wlcore
* fix a double free regression causing hard to track crashes
rtl8xxxu
* fix driver reload issues, a memory leak and an endian bug
rtlwifi
* fix a major regression introduced in 4.9 with firmware loading on
certain hardware
ath10k
* fix regression about broken cal_data debugfs file (since 4.7)
ath9k
* revert temperature compensation for AR9003+ devices, it was causing
too much problems
ath6kl
* add Dell OEM SDIO I/O for the Venue 8 Pro
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The quality of ADC entropy is 10 bits of min-entropy for
a 32-bit value, change '(((x) * 8 * 320) >> 10)' to
'(((x) * 8 * 10) >> 5)' for easier understanding.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
arvifs list is traversed within data_lock spin_lock in tasklet
context to fill channel information from the corresponding vif.
This means any access to arvifs list for add/del operations
should also be protected with the same spin_lock to avoid the
race. Fix this by performing list add/del on arvfis within the
data_lock. This could fix kernel panic something like the below.
LR is at ath10k_htt_rx_pktlog_completion_handler+0x100/0xb6c [ath10k_core]
PC is at ath10k_htt_rx_pktlog_completion_handler+0x1c0/0xb6c [ath10k_core]
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[<bf4857f4>] (ath10k_htt_rx_pktlog_completion_handler+0x2f4/0xb6c [ath10k_core])
[<bf487540>] (ath10k_htt_txrx_compl_task+0x8b4/0x1188 [ath10k_core])
[<c00312d4>] (tasklet_action+0x8c/0xec)
[<c00309a8>] (__do_softirq+0xdc/0x208)
[<c0030d6c>] (irq_exit+0x84/0xe0)
[<c005db04>] (__handle_domain_irq+0x80/0xa0)
[<c00085c4>] (gic_handle_irq+0x38/0x5c)
[<c0009640>] (__irq_svc+0x40/0x74)
(gdb) list *(ath10k_htt_rx_pktlog_completion_handler+0x1c0)
0x136c0 is in ath10k_htt_rx_h_channel (drivers/net/wireless/ath/ath10k/htt_rx.c:769)
764 struct cfg80211_chan_def def;
765
766 lockdep_assert_held(&ar->data_lock);
767
768 list_for_each_entry(arvif, &ar->arvifs, list) {
769 if (arvif->vdev_id == vdev_id &&
770 ath10k_mac_vif_chan(arvif->vif, &def) == 0)
771 return def.chan;
772 }
773
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_rx_h_unchain' needs to be called only if the return
value from 'ath10k_htt_rx_amsdu_pop' is 1('chained msdu's'), this
change makes it more explicit and avoids doing a skb_peek, fetching
rx descriptor pointer, checking rx msdu decap format for the case of
ret = 0 (unchained msdus). Found this change during code walk through,
not sure if this addresses any issue.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the growing parameter list to a structure for the interface
combination check and iteration functions in cfg80211 and mac80211
to make the code easier to understand.
Signed-off-by: Purushottam Kushwaha <pkushwah@qti.qualcomm.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SDIO ID 0271:0418
Signed-off-by: Alan Cox <alan@linux.intel.com>
Bugzilla-ID: https://bugzilla.kernel.org/show_bug.cgi?id=67921
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This reverts commit 171f6402e4 ("ath9k_hw: implement temperature compensation
support for AR9003+"). Some users report that this commit causes a regression
in performance under some conditions.
Fixes: 171f6402e4 ("ath9k_hw: implement temperature compensation support for AR9003+")
Cc: <stable@vger.kernel.org> # 4.8
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 0b8e3c4ca2 ("ath10k: move cal data len to hw_params") broke retrieving
the calibration data from cal_data debugfs file. The length of file was always
zero. The reason is:
static ssize_t ath10k_debug_cal_data_read(struct file *file,
char __user *user_buf,
size_t count, loff_t *ppos)
{
struct ath10k *ar = file->private_data;
void *buf = file->private_data;
This is obviously bogus, private_data cannot contain both struct ath10k and the
buffer. Fix it by caching calibration data to ar->debug.cal_data. This also
allows it to be accessed when the device is not active (interface is down).
The cal_data buffer is fixed size because during the first firmware probe we
don't yet know what will be the lenght of the calibration data. It was simplest
just to use a fixed length. There's a WARN_ON() in
ath10k_debug_cal_data_fetch() if the buffer is too small.
Tested with qca988x and firmware 10.2.4.70.56.
Reported-by: Nikolay Martynov <mar.kolya@gmail.com>
Fixes: 0b8e3c4ca2 ("ath10k: move cal data len to hw_params")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Marty Faltesek <mfaltesek@google.com>
[kvalo@qca.qualcomm.com: improve commit log and minor other changes]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In commit d86e647688 ("rtlwifi: rtl818x: constify local structures"),
the configuration struct for most of the drivers was changed to be
constant. The problem is that five of the modified drivers need to be
able to update the firmware name based on the exact model of the card.
As the file names were stored in one of the members of that struct,
these drivers would fail with a kernel BUG splat when they tried to
update the firmware name.
Rather than reverting the previous commit, I used a suggestion by
Johannes Berg and made the firmware file name pointers be local to
the routines that update the software variables.
The configuration struct of rtl8192cu, which was not touched in the
previous patch, is now constantfied.
Fixes: d86e647688 ("rtlwifi: rtl818x: constify local structures")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.8
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of building the multi-channel ops at runtime, declare
the common ops with a macro and build both that way, so that
the multi-channel ops can also be const.
As a side effect, due to the removed code, this decreases the
size of the module (while shifting data from .bss to .text
due to the newly added const).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not accept arbitrary DA/SA inside A-MSDUs, it could be used
to circumvent protections, like allowing a station to send frames and
make them seem to come from somewhere else.
Add the necessary infrastructure in cfg80211 to allow such checks, in
further patches we'll start using them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's only a single case where has_80211_header is passed as true,
which is in mac80211. Given that there's only simple code that needs
to be done before calling it, export that function from cfg80211
instead and let mac80211 call it itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull misc vfs updates from Al Viro:
"Assorted misc bits and pieces.
There are several single-topic branches left after this (rename2
series from Miklos, current_time series from Deepa Dinamani, xattr
series from Andreas, uaccess stuff from from me) and I'd prefer to
send those separately"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (39 commits)
proc: switch auxv to use of __mem_open()
hpfs: support FIEMAP
cifs: get rid of unused arguments of CIFSSMBWrite()
posix_acl: uapi header split
posix_acl: xattr representation cleanups
fs/aio.c: eliminate redundant loads in put_aio_ring_file
fs/internal.h: add const to ns_dentry_operations declaration
compat: remove compat_printk()
fs/buffer.c: make __getblk_slow() static
proc: unsigned file descriptors
fs/file: more unsigned file descriptors
fs: compat: remove redundant check of nr_segs
cachefiles: Fix attempt to read i_blocks after deleting file [ver #2]
cifs: don't use memcpy() to copy struct iov_iter
get rid of separate multipage fault-in primitives
fs: Avoid premature clearing of capabilities
fs: Give dentry to inode_change_ok() instead of inode
fuse: Propagate dentry down to inode_change_ok()
ceph: Propagate dentry down to inode_change_ok()
xfs: Propagate dentry down to inode_change_ok()
...
The 8192eu suffered from two issues when reloading the driver.
The same problems as with the 8723bu where REG_RX_WAIT_CCA bits 22 and
23 didn't get set in rtl8192e_enable_rf().
In addition it also seems prone to issues when setting REG_RF_CTRL to
0 intead of just disabling the RF_ENABLE bit. Similar to what was
causing issues with the 8188eu.
With this patch I can successfully reload the driver and reassociate
to an APi with an 8192eu dongle.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The generic disable_rf() function clears bits 22 and 23 in
REG_RX_WAIT_CCA, however we did not re-enable them again in
rtl8723b_enable_rf()
This resolves the problem for me with 8723bu devices not working again
after reloading the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The full RX descriptor is converted so converting tsfl again would
return it to it's original endian value.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A device running without RX package aggregation could return more data
in the USB packet than the actual network packet. In this case we
could would clone the skb but then determine that that there was no
packet to handle and exit without freeing the cloned skb first.
This has so far only been observed with 8188eu devices, but could
affect others.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When power is removed from the device, all of the SDIO settings
return to default. Fix that by reconfiguring after power is
applied.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows the hardware to be restarted, as it will cause the
sg to be reinitialized.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reuse the busreqs in case of hardware restart, they must be
properly reinitialized. If the scat_req pointer isn't reset to
0, __ath6kl_sdio_write_async() will assume there is sg work to be
done (causing a kernel OOPS).
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
It's not necessary to free memory allocated with devm_kzalloc
and using kfree leads to a double free.
Fixes: d776fc86b8 ("wlcore: sdio: Populate config firmware data")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.
In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be helpful for drivers that can acquire
alpha2 regulatory codes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to get the TPC stats for 10.4 fw variants.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that happened
in 4.8 for that filesystem. Overall, nothing major, just a few fixes
and cleanups.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNw4PHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspLVYAoNXr
FXBHGb2tNT/1PLfvUCwd5PqWAJ9Khb5WAHtvjTmEN1zabz45aSbcrA==
=Uz6V
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that
happened in 4.8 for that filesystem. Overall, nothing major, just a
few fixes and cleanups.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent()
drivers: dma-coherent: Fix DMA coherent size for less than page
MAINTAINERS: extend firmware_class maintainer list
debugfs: propagate release() call result
driver-core: platform: Catch errors from calls to irq_get_irq_data
sysfs print name of undiscoverable attribute group
carl9170: fix debugfs crashes
b43legacy: fix debugfs crash
b43: fix debugfs crash
debugfs: introduce a public file_operations accessor
device core: Remove deprecated create_singlethread_workqueue
drivers/base dmam_declare_coherent_memory leaks
platform: don't return 0 from platform_get_irq[_byname]() on error
cpu: clean up register_cpu func
dma-mapping: use vma_pages().
drivers: dma-coherent: use vma_pages().
attribute_container: Fix typo
base: soc: make it explicitly non-modular
drivers: base: dma-mapping: page align the size when unmap_kernel_range
platform driver: fix use-after-free in platform_device_del()
...
Major changes:
iwlwifi
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support (API 26)
* add 8275 series support
* add 9560 series support
* add support for MU-MIMO sniffer
* add support for RRM by scan
* add support for "reverse" rx packet injection faking hw descriptors
* migrate to devm memory allocation handling
* Remove support for older firmwares (API older than -17 and -22)
wl12xx
* support booting the same rootfs with both wl12xx and wl18xx
hostap
* mark the driver as obsolete
ath9k
* disable RNG by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX7UPbAAoJEG4XJFUm622bmgIH/2fCGwkejWpN/KLckRU0I+ze
Yx0o8aEmYAOnZW4tVVGAtEAxeLdzjMeHKsyJ+4RBguhRpbV2FTKnzg7LYeqqI3Vw
LjZwKLrrBj4DXQwtTxBC8uScUpDU91U4mZwOTN+UkyXQb9hDxl2CH3MUgc432hcd
flSXTnaY8TJzFuHM9Q/TORXmSx3VtMqYnqUYcyoaKEC8ZiSr6dWtzh5OkPS+O4Di
4CNPDjEK5uhe46gDWJhGY2bx6TnzGx6O5mRfWfzdvL3Fzy9a3rGabA9Iis+9b23n
m/5OKwN97jcPZiWrP+c2qfVmFjv2upCUUAuLuT0k05/DK70qpGKyMwklsNcC44Q=
=lRW5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-09-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
wireless-drivers-next patches for 4.9
Major changes:
iwlwifi
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support (API 26)
* add 8275 series support
* add 9560 series support
* add support for MU-MIMO sniffer
* add support for RRM by scan
* add support for "reverse" rx packet injection faking hw descriptors
* migrate to devm memory allocation handling
* Remove support for older firmwares (API older than -17 and -22)
wl12xx
* support booting the same rootfs with both wl12xx and wl18xx
hostap
* mark the driver as obsolete
ath9k
* disable RNG by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k RNG will dominates all the noise sources from the real HW
RNG, disable it by default. But we strongly recommand to enable
it if the system without HW RNG, especially on embedded systems.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Flowrings contain skbs waiting for transmission that were passed to us
by netif. It means we checked every one of them looking for 802.1x
Ethernet type. When deleting flowring we have to use freeing function
that will check for 802.1x type as well.
Freeing skbs without a proper check was leading to counter not being
properly decreased. This was triggering a WARNING every time
brcmf_netdev_wait_pend8021x was called.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend@broadcom.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Even with timeout increased to 950 ms we get WARNINGs from time to time.
It mostly happens on A-MPDU stalls (e.g. when station goes out of
range). It may take up to 5-10 secods for the firmware to recover and
for that time it doesn't process packets.
It's still useful to have a message on time out as it may indicate some
firmware problem and incorrect key update. Raising a WARNING however
wasn't really that necessary, it doesn't point to any driver bug anymore
and backtrace wasn't much useful.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The entries in this enum may be referenced in debug output. Adding explicit
values simplifies the lookup.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rtl8821ae implements WOWLAN; however, the other drivers may receive
a call requesting information about this mode. The other drivers need to
ignore the request rather than logging that the default branch of the
switch statement has been reached.
Reported by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Help along debugging by showing what switch/case variable is not
being processed in these messages.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Small fix in CTDP error handling;
* Remove support for older firmwares;
* Clean-ups and a few simple fixes here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJX6YI4AAoJEKFHnKIaPMX6fh0QAJwFfvpZ9gG/TQbxHeqxqQS1
ZQ8bV/8mCkMZlifAeR5NGEEkIwdHl/nCkkwZv9j4vGCb0M6qA2Pd8Uh1tpJgkSlB
c4NK9LdLdRJBJkpXOgCW9gPPgXAP3/9VqOMNm4jx0RPLpjBhCopcubLFcymND7cc
OGIvs1RkragAUkIKQw2jy9HauRV6co+R99ZFTcVCPalNhtmgrdfZzZaN13S2VYjV
ln+fepJFeL2HgDyvx4FdnfzwPHgk90/b/kSmSQJ/ebRNVn2BAkG3BEyAIG4kEcBa
jsavKYjGNXIlGOoab0gY3WZdcxk3AprOYwIELxFzMML5sXYvY9K/9EpYLNPSiHIy
cwYlvV9Itq0GAtVFyatqoqy4yO951MlLd7+gfBP8a/6K1T22sMayg+B/dHROo4UG
SIdI/Ayai1SVuAyMpO9AK9jsC+uWcyR9DhyWT2fC1zzYQ3wtfVfWlDcXqtfZDjTC
QlVI2uOGsVeNFUSNGCOxOoOBIaRzGB2FwU9jVIideeMEWVL1qVMeBz3Nooi1z33k
o6qvm6N8674JqlKC/WQn87k2+gsKSGEgRVEEF1HyA3CP5NQ7aU7ZNQJGiNxsezwd
hSSgu3WseB2OT19W6rjPkonrgS2C7ecU7oL0Y84ozW2hkS0vgtD8QLau8aIHUL/t
hqIwPQ1lb/8B/X5t7ECl
=MdMZ
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-09-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Some new HW IDs;
* Small fix in CTDP error handling;
* Remove support for older firmwares;
* Clean-ups and a few simple fixes here and there.
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of reset_control_get() to simplify the
failure path and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the managed variant of clk_get() to simplify the failure path
and the .remove callback.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Correct some trivial comment typos.
Remove unnecessary parentheses in a long line.
Signed-off-by: Joe Perches <joe@perches.com>
[kvalo@qca.qualcomm.com: drop the change for return]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we unshare a queue, the ADD_STA was not properly
initialised.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware has a new smart linker, and this table can now be
in ICCM or in SMEM. It is not hardcoded, but depends on code
size. Allow the full range.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This define should really be TX_CMD_SEC_KEY_FROM_TABLE
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW versions older than -17 for 3160 and 7260 and older than -22 for
newer NICs are not supported anymore. Don't load these versions
and remove code that handles them.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
They seem to be there from the first day. We calculate these values but
never use them.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is called from get_station callback which means that every
time user space was getting/dumping station(s) we were leaking 2 KiB.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 1f0dc59a6d ("brcmfmac: rework .get_station() callback")
Cc: stable@vger.kernel.org # 4.2+
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As soon as debugging is turned on, the logs are filled with messages
reporting the interrupt status. As this quantity is usually zero, this
output is not needed. In fact, there will be a report if the status is
not zero, thus the debug line in question could probably be deleted.
Rather than taking that action, I have changed it to only be printed
when the newly added RTL8XXXU_DEBUG_INTERRUPT bit is set in the debug
mask.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This saves some 217, or about, derefences of priv->fops.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove last_tx_page argument from the llt_init() function. The
rtl8xxxu_fileops structure contains the correct TX_TOTAL_PAGE_NUM
value for the device, and rtl8xxxu_auto_llt_table() doesn't need to
know the value in the first place.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was detected tracing the 8188eu driver, but doesn't seem to make
any difference when using it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch helps get rid of goto statement and improves readability.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that in a corner case mwifiex_usb_tx_complete()
gets called before we exit from mwifiex_usb_host_to_card() after
submitting the urb. 'data_sent' flag remains set in this case. It
blocks further Tx packets and triggers watchdog timeout.
The problem is fixed by setting data_sent and port_block flag at
correct place.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Following crash issue is observed during TCP traffic stress
test
[ 2253.625439] NMI watchdog: BUG: soft lockup - CPU#3 stuck for 22s!
[kworker/u17:1:5191]
[ 2253.625520] Call Trace:
[ 2253.625527] [<ffffffffc0b47030>] ? moal_spin_lock+0x30/0x30
[usb8xxx]
[ 2253.625533] [<ffffffffc0ac3ceb>] ? wlan_wmm_lists_empty+0xb/0xf0
[mlan]
[ 2253.625537] [<ffffffffc0ab0ea3>] mlan_main_process+0x1b3/0x720
[mlan]
[ 2253.625540] [<ffffffffc0b337f5>] woal_main_work_queue+0x45/0x80
[usb8xxx]
[ 2253.625543] [<ffffffff8108aaf0>] process_one_work+0x150/0x3f0
[ 2253.625545] [<ffffffff8108b1e1>] worker_thread+0x121/0x520
[ 2253.625547] [<ffffffff8108b0c0>] ? rescuer_thread+0x330/0x330
[ 2253.625549] [<ffffffff81090222>] kthread+0xd2/0xf0
[ 2253.625551] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
[ 2253.625553] [<ffffffff8179423c>] ret_from_fork+0x7c/0xb0
[ 2253.625555] [<ffffffff81090150>] ?
kthread_create_on_node+0x1c0/0x1c0
In mwifiex_usb_tx_complete(), we are updating port->block_status first
and then freeing the skb attached to that URB. We may end up attaching
new skb to URB in a corner case and same will be freed. This results in
the kernel crash. The problem is solved by changing the sequence.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 802.11 standard only has four valid auth type configurations of which
our firmware only supports two, ie. Open System and Shared Key. Simplify
the mapping falling back to automatic for other types specified by
user-space.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clearing the wowl wakeindicator happens with a rather odd
construction where the string "clear" is used to set the iovar
wowl_wakeind. This was implemented incorrectly as it caused an
out of bound access. Use an intermediate variable of correct
length and copy string in that. Problem was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When IPv6 address is to be cleared there is a possible out of
bound access. But also the clearing of the last entry and the
adjustment of total number of stored IPv6 addresses is not
updated. This patch fixes that bug. Bug was found using coverity.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
in the function brcmf_bus_start() in the exception handling a
check is made to dermine whether ifp is null, though this is not
possible. Removing the unnessary check.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As it turns out there is no need to use a worker for the callback
because it is not called from atomic context.
Reported-by: Dan Williams <dcbw@redhat.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of an error the variable returned is uninitialized. The caller
will probably check the error code before using it, but better assure
it is set to zero.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the error paths in brcmf_flowring_add_tdls_peer() the allocated
resource should be freed.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variable info is assigned to point to bcdc->msg[1], which is the
same as pointing to bcdc->buf. As that is what we want to access
make it clear by fixing the assignment. This also avoid out-of-bounds
errors from static analyzers are bcdc->msg[1] is not in the structure
definition.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
802.11d is not always supported by firmware anymore. Currently the
AP configuration of 11d will cause an abort if the ioctl set is
failing. This behavior is not correct and the error should be
ignored.
Reviewed-by: Arend Van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Previously device used to start using IGTK key as Tx key as soon as it
gets downloaded in add_key(). This patch implements set_default_mgmt_key
handler. We will update Tx key ID in set_default_mgmt_key().
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the wl18xx specific config firmware we now have available.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Booting multiple wl12xx and wl18xx devices using the same rootfs is
a pain. You currently have to symlink the right nvs file depending
on the wl12xx type.
For example, with wl1271-nvs.bin being a symlink to wl127x-nvs.bin
by default and trying to bring up a wl128x based device:
wlcore: ERROR nvs size is not as expected: 1113 != 912
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR NVS file is needed during boot
wlcore: ERROR firmware boot failed despite 3 retries
Note that wl18xx uses a separate config firmware wl18xx-conf.bin
that can be generated with tools using the following two git repos:
git.ti.com/wilink8-wlan/18xx-ti-utils
git.ti.com/wilink8-wlan/wl18xx_fw
So let's not configure the nvs file for wl18xx as it's not needed
AFAIK. If it turns out that we also need the nvs file for wl18xx,
we can just add it to the config firmware data for wl18xx.
Let's fix the issue by using the chip specific config firmware
data, and make sure we produce understandable warnings if something
is missing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the config firmware names and make it available
in platform data.
Let's also fix the order of the struct wilink_family_data
while at it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the config firmware names and make it available
in platform data.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move struct wilink_family_data to be available for all TI WLAN
variants. And fix familiy typo, it should be just family.
Looks like wl12xx use two different nvs.bin files and wl18xx
uses a different conf.bin file.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The upper bound IWL_RATE_COUNT_LEGACY should be used
with a >= check, rejecting the value itself; fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were assigning the return value of iwl_mvm_ctdp_command() to a
variable, but never checking it. If this command fails, we should not
allow the interface up process to proceed, since it is potentially
dangerous to ignore thermal management requirements.
Fixes: commit 5c89e7bc55 ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The various TFD/TB helpers have two code paths depending on the
type of TFD supported, with variable shadowing due to the new if
branches. Move the fall-through code into else branches to avoid
variable shadowing. While doing so, rename some of the variables
and do some other cleanups (like removing void * casts of void *
pointers.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the init_dbg check to earlier in the function to simplify the
code.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ben Greear reported:
> I see lots of instability as soon as I load up the carl9710 NIC.
> My application is going to be poking at it's debugfs files...
>
> BUG: KASAN: slab-out-of-bounds in carl9170_debugfs_read+0xd5/0x2a0
> [carl9170] at addr 0xffff8801bc1208b0
> Read of size 8 by task btserver/5888
> =======================================================================
> BUG kmalloc-256 (Tainted: G W ): kasan: bad access detected
> -----------------------------------------------------------------------
>
> INFO: Allocated in seq_open+0x50/0x100 age=2690 cpu=2 pid=772
>...
This breakage was caused by the introduction of intermediate
fops in debugfs by commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Thankfully, the original/real fops are still available in d_fsdata.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a crash that happens because b43legacy's
debugfs code expects file->f_op to be a pointer to its own
b43legacy_debugfs_fops struct. This is no longer the case
since commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a crash that happens because b43's
debugfs code expects file->f_op to be a pointer to
its own b43_debugfs_fops struct. This is no longer
the case since commit 9fd4dcece4
("debugfs: prevent access to possibly dead file_operations at file open")
Reviewed-by: Nicolai Stange <nicstange@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cc: stable <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to declare a list and then init it manually,
just use the LIST_HEAD() macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to declare a list and then init it manually,
just use the LIST_HEAD() macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently it is logged as UNKNOWN.
Also, 0x6c seems to be the permanent ID for this command, remove
incorrect comment and uncomment the command from the commands
list.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to access cached/paged memory, there are a couple of firmware
commands (one for UMAC and one for LMAC) that let the host access memory
and registers indirectly. Since this is done by the firmware on behalf
of the host, even if memory is paged out or cached, the host will
retrieve the memory as the firmware sees it (paged out memory will get
paged in).
Export this mechanism via a debugfs entry for both read and write
access.
WARNING: This mechanism has no protections at all. Invalid addresses may
crash or hang the firmware. Writing to arbitrary memory also comes with
no guarantees.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need for the common MAC context function to have an
if on AP mode, the values can be overridden in the AP-specific
function later. Clean that up by adding the full command as a
new parameter to the AP-specific function, and doing it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New function, reveals the diff between gp2 and host time.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we get an unexpected Block Ack Request frame, the BAID from
the hardware will be invalid, and we'll pass it to mac80211 for
further handling (sending a delBA action frame.)
Add a comment explaining that, in case anyone looks in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to firmware design considerations, move to wide ID for
all commands.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in making this an out-of-line function
since it just calls a single other function with a few
changed parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Log group as well. Remove 0x prefix to match TX logging.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will be used by more than MVM, so move it to iwlwifi
While at it, rename WRD_METHOD to the more appropriate
WRDD_METHOD and add some documentation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For automatic testing packet injection can be useful.
Support injection through debugfs.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement support for RRM by adding an option to configure the scan
dwell time and reporting scan start time and BSS detection time, and
Advertise support for these features.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On default queue we will not receive frame release notification,
but the BAR itself.
Upon receiving the BAR driver should look at the NSSN and adjust
window accordingly.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There was recently a Full AP mode feature added where hostap adds
the station at auth stage, and not assoc.
However, when running with legacy hostapd, we get the auth response
before station was added, and tx_skb_non_sta fails to allocate
a queue, resulting in a complete failure of association.
Take care of this situation as well.
Add a warning when no valid queue is returned at all and make mvm
drop the packet instead of passing it on.
Refactor the function a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 9000 family products we added an option to let the OEM fuse the
mac address via registers. If these registers are zeroed we use the OTP
address instead. Make sure that the address provided by the OEM is valid
and, if not, fall back to the OTP address as well.
Fixes: commit 17c867bfe8 ("iwlwifi: add support for getting HW address from CSR")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
enable MU-MIMO air sniffer if it's supported by the NIC
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When comparing command IDs, the group should be taken
into account so the same command/notification from a
different group doesn't trigger anything unexpected.
Fix this by comparing to the wide ID.
Fixes: commit 1738d60b31 ("iwlwifi: mvm: handle RX MPDUs separately")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use skb_queue_empty() and not skb_peek_tail() to check for
empty list.
Avoid a redundant check as well - loop will take care of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
-----BEGIN PGP SIGNATURE-----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=s1MY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-09-16' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have various things - all across the board:
* MU-MIMO sniffer support in mac80211
* a create_singlethread_workqueue() cleanup
* interface dump filtering that was documented but not implemented
* support for the new radiotap timestamp field
* send delBA in two unexpected conditions (as required by the spec)
* connect keys cleanups - allow only WEP with index 0-3
* per-station aggregation limit to work around broken APs
* debugfs improvement for the integrated codel algorithm
and various other small improvements and cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If adapter is null the error exit path in mwifiex_shutdown_sw is
to down the semaphore sem and print some debug via mwifiex_dbg.
However, passing a NULL adapter to mwifiex_dbg causes a null
pointer deference when accessing adapter->dev. This fix checks
for a null adapter at the start of the function and to exit
without the need to up the semaphore and we also skip the debug
to avoid the null pointer dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
smatch reports:
sta_cmdresp.c:1053 mwifiex_create_custom_regdomain() warn: possible memory leak of 'regd'
Indeed, mwifiex_create_custom_regdomain() returns NULL in the
case that channel is missing in the TLV without freeing regd.
Moreover, some other error paths in this function return ERR_PTR
values which are assigned without checking to the regd field in
the mwifiex_adapter struct. The latter is only null-checked where
used.
Fix by freeing regd in the error path, and only update
priv->adapter->regd if the returned pointer is valid.
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This powers down the 8192e correctly, or at least to the point where
the firmware will load again, when reloading the driver module.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support
* general cleanups and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SrvZ
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-09-15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support
* general cleanups and improvements
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX2rF7AAoJEG4XJFUm622bD3EH/icZDT7vVxnb0VPP8jAScA4h
bMNrI3iFxnPohO8Rzp+edWSdxEZoxwrBVk/6BHXO9PHHZwPX7/b8/OOXmLWB2X1c
ffj1jt83RENcsZFvd5OJfDYxIq89uOkWybdD6nIUd3umKC9KeFOI5nCju31fEZrQ
ZptqvKGIV36bbx07K8Y/PQRL2SA6T+09WqvuljLHZD5hfPGZ+GWXV2p+HAm3Moos
iy6HUx5+pYfC+zlcmvJvL47Wxj+HppS/48ujyQ68DD2UkjOtF620YJjVy3o+njip
GNJtCgWFDp2ar3uvRP2BfBd9FtseDTKsKusxJQvNGoSR0ON+uGIzURCznQ+2PCM=
=FyXw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-09-15' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.9
Major changes:
iwlwifi
* preparation for new a000 HW continues
* some DQA improvements
* add support for GMAC
* add support for 9460, 9270 and 9170 series
mwifiex
* support random MAC address for scanning
* add HT aggregation support for adhoc mode
* add custom regulatory domain support
* add manufacturing mode support via nl80211 testmode interface
bcma
* support BCM53573 series of wireless SoCs
bitfield.h
* add FIELD_PREP() and FIELD_GET() macros
mt7601u
* convert to use the new bitfield.h macros
brcmfmac
* add support for bcm4339 chip with modalias sdio:c00v02D0d4339
ath10k
* add nl80211 testmode support for 10.4 firmware
* hide kernel addresses from logs using %pK format specifier
* implement NAPI support
* enable peer stats by default
ath9k
* use ieee80211_tx_status_noskb where possible
wil6210
* extract firmware capabilities from the firmware file
ath6kl
* enable firmware crash dumps on the AR6004
ath-current is also merged to fix a conflict in ath10k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to initialize at runtime, when the static
declaration macro can just be used instead, so do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As pointed out by smatch, checking the BAID for just >= INVALID
is a bad idea since only 32 (IWL_MAX_BAID) actually exist. Check
the range for that and print invalid ones in the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Inside the reorder timer expire function, there's no point in
disabling BHs since it is in BH context. Remove that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware ever decides to send any new/more notifications
to the RSS queues, the driver would currently try to interpret
those as REPLY_RX_MPDU_CMD and, if the notification was small,
access invalid memory.
Prevent that by checking for REPLY_RX_MPDU_CMD explicitly which
allows ignoring unexpected notifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In MSIX mode the number of irq depends on the number of
possible cpus existing on the host.
This cause to bug in case there are offline cores.
Take into account only the online CPUs instead.
Also save it in temporary variable.
Fixes: commit 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver now support version 26 of the firmware APIs.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Function is very indented. Go to msi section if needed to avoid
it and by that make the code more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use setup_timer function instead of initializing timer with the function
and data fields
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new 8275 series and add
the first PCI ID for it.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new config struct for the new 9560 series and add
the 4 new PCI IDs for it.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to utilize the host's CPUs in the most efficient way
we bind each rx interrupt vector to each CPU on the host.
Each rx interrupt is prioritized to execute only on the designated CPU
rather than any CPU.
Processor affinity takes advantage of the fact that some remnants of
a process that was run on a given processor may remain in that
processor's memory state for example, data in the CPU cache after
another process is run on that CPU. Scheduling that process to execute
on the same processor could result in an efficient use of process by
reducing performance-degrading situations such as cache misses
and parallel processing.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a STA is removed in DQA mode, if no traffic went through
its reserved queue, the txq continues to be marked as
reserved and no STA can use it.
Make sure that in such a case the reserved queue is marked
as free when the STA is removed.
Fixes: commit 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
