Currently this error message does not say a lot:
[ 32.693498] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.699725] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.705931] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.712139] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.718347] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
[ 32.724554] DSA: failed to notify tag_8021q VLAN deletion: -ENOENT
but in this form, it is immediately obvious (at least to me) what the
problem is, even without further looking at the code:
[ 12.345566] sja1105 spi2.0: port 0 failed to notify tag_8021q VLAN 1088 deletion: -ENOENT
[ 12.353804] sja1105 spi2.0: port 0 failed to notify tag_8021q VLAN 2112 deletion: -ENOENT
[ 12.362019] sja1105 spi2.0: port 1 failed to notify tag_8021q VLAN 1089 deletion: -ENOENT
[ 12.370246] sja1105 spi2.0: port 1 failed to notify tag_8021q VLAN 2113 deletion: -ENOENT
[ 12.378466] sja1105 spi2.0: port 2 failed to notify tag_8021q VLAN 1090 deletion: -ENOENT
[ 12.386683] sja1105 spi2.0: port 2 failed to notify tag_8021q VLAN 2114 deletion: -ENOENT
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ida_alloc_range() may return other than -ENOMEM error code.
Unshadow it in the wwan_create_port().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port leaves a VLAN-aware bridge, the current code does not clear
other ports' matrix field bit. If the bridge is later set to VLAN-unaware
mode, traffic in the bridge may leak to that port.
Remove the VLAN filtering check in mt7530_port_bridge_leave.
Fixes: 474a2ddaa1 ("net: dsa: mt7530: fix VLAN traffic leaks")
Fixes: 83163f7dca ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TJA1102 provides interrupt notification for the critical health states
like overtemperature and undervoltage.
The overtemperature bit is set if package temperature is beyond 155C°.
This functionality was tested by heating the package up to 200C°
The undervoltage bit is set if supply voltage drops beyond some critical
threshold. Currently not tested.
In a typical use case, both of this events should be logged and stored
(or send to some remote system) for further investigations.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nick Richardson says:
====================
pktgen: Add IMIX mode
Adds internet mix (IMIX) mode to pktgen. Internet mix is
included in many user-space network perf testing tools. It allows
for the user to specify a distribution of discrete packet sizes to be
generated. This type of test is common among vendors when perf testing
their devices.
[RFC link: https://datatracker.ietf.org/doc/html/rfc2544#section-9.1]
This allows users to get a
more complete picture of how their device will perform in the
real-world.
This feature adds a command that allows users to specify an imix
distribution in the following format:
imix_weights size_1,weight_1 size_2,weight_2 ... size_n,weight_n
The distribution of packets with size_i will be
(weight_i / total_weights) where
total_weights = weight_1 + weight_2 + ... + weight_n
For example:
imix_weights 40,7 576,4 1500,1
The pkt_size "40" will account for 7 / (7 + 4 + 1) = ~58% of the total
packets sent.
This patch was tested with the following:
1. imix_weights = 40,7 576,4 1500,1
2. imix_weights = 0,7 576,4 1500,1
- Packet size of 0 is resized to the minimum, 42
3. imix_weights = 40,7 576,4 1500,1 count = 0
- Zero count.
- Runs until user stops pktgen.
Invalid Configurations
1. clone_skb = 200 imix_weights = 40,7 576,4 1500,1
- Returns error code -524 (-ENOTSUPP) when setting imix_weights
2. len(imix_weights) > MAX_IMIX_ENTRIES
- Returns -7 (-E2BIG)
This patch is split into three parts, each provide different aspects of
required functionality:
1. Parse internet mix input.
2. Add IMIX Distribution representation.
3. Process and output IMIX results.
Changes in v2:
* Remove __ prefix outside of uAPI.
* Use seq_puts instead of seq_printf where necessary.
* Reorder variable declaration.
* Return -EINVAL instead of -ENOTSUPP when using IMIX with clone_skb > 0
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The bps for imix mode is calculated by:
sum(imix_entry.size) / time_elapsed
The actual counts of each imix_entry are displayed under the
"Current:" section of the interface output in the following format:
imix_size_counts: size_1,count_1 size_2,count_2 ... size_n,count_n
Example (count = 200000):
imix_weights: 256,1 859,3 205,2
imix_size_counts: 256,32082 859,99796 205,68122
Result: OK: 17992362(c17964678+d27684) usec, 200000 (859byte,0frags)
11115pps 47Mb/sec (47977140bps) errors: 0
Summary of changes:
Calculate bps based on imix counters when in IMIX mode.
Add output for IMIX counters.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to represent the distribution of imix packet sizes, a
pre-computed data structure is used. It features 100 (IMIX_PRECISION)
"bins". Contiguous ranges of these bins represent the respective
packet size of each imix entry. This is done to avoid the overhead of
selecting the correct imix packet size based on the corresponding weights.
Example:
imix_weights 40,7 576,4 1500,1
total_weight = 7 + 4 + 1 = 12
pkt_size 40 occurs 7/total_weight = 58% of the time
pkt_size 576 occurs 4/total_weight = 33% of the time
pkt_size 1500 occurs 1/total_weight = 9% of the time
We generate a random number between 0-100 and select the corresponding
packet size based on the specified weights.
Eg. random number = 358723895 % 100 = 65
Selects the packet size corresponding to index:65 in the pre-computed
imix_distribution array.
An example of the pre-computed array is below:
The imix_distribution will look like the following:
0 -> 0 (index of imix_entry.size == 40)
1 -> 0 (index of imix_entry.size == 40)
2 -> 0 (index of imix_entry.size == 40)
[...] -> 0 (index of imix_entry.size == 40)
57 -> 0 (index of imix_entry.size == 40)
58 -> 1 (index of imix_entry.size == 576)
[...] -> 1 (index of imix_entry.size == 576)
90 -> 1 (index of imix_entry.size == 576)
91 -> 2 (index of imix_entry.size == 1500)
[...] -> 2 (index of imix_entry.size == 1500)
99 -> 2 (index of imix_entry.size == 1500)
Create and use "bin" representation of the imix distribution.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds "imix_weights" command for specifying internet mix distribution.
The command is in this format:
"imix_weights size_1,weight_1 size_2,weight_2 ... size_n,weight_n"
where the probability that packet size_i is picked is:
weight_i / (weight_1 + weight_2 + .. + weight_n)
The user may provide up to 100 imix entries (size_i,weight_i) in this
command.
The user specified imix entries will be displayed in the "Params"
section of the interface output.
Values for clone_skb > 0 is not supported in IMIX mode.
Summary of changes:
Add flag for enabling internet mix mode.
Add command (imix_weights) for internet mix input.
Return -ENOTSUPP when clone_skb > 0 in IMIX mode.
Display imix_weights in Params.
Create data structures to store imix entries and distribution.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When global vlan options are equal sequentially we compress them in a
range to save space and reduce processing time. In order to have the
proper range end id we need to update range_end if the options are equal
otherwise we get ranges with the same end vlan id as the start.
Fixes: 743a53d963 ("net: bridge: vlan: add support for dumping global vlan options")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210810092139.11700-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change adds a 'type' attribute to routes, which can be parsed from
a RTM_NEWROUTE message. This will help to distinguish local vs. peer
routes in a future change.
This means userspace will need to set a correct rtm_type in RTM_NEWROUTE
and RTM_DELROUTE messages; we currently only accept RTN_UNICAST.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20210810023834.2231088-1-jk@codeconstruct.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, four reset types are supported for the HNS3 ethernet
driver: IMP reset, global reset, function reset, and FLR. Only
FLR can now be triggered by the user. To restore the device when
an exception occurs, add support for triggering reset by ethtool.
Run the "ethtool --reset DEVNAME mgmt | all | dedicated" to
trigger the IMP | global | function reset manually.
In addition, VF can only trigger function reset.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Link: https://lore.kernel.org/r/1628602128-15640-1-git-send-email-huangguangbin2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonathan Toppins says:
====================
bonding: cleanup header file and error msgs
Two small patches removing unreferenced symbols and unifying error
messages across netlink and printk.
====================
Link: https://lore.kernel.org/r/cover.1628650079.git.jtoppins@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There seems to be no reason to have different error messages between
netlink and printk. It also cleans up the function slightly.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All of the symbols either only exist in bond_options.c or nowhere at
all. These symbols were verified to not exist in the code base by
using `git grep` and their removal was verified by compiling bonding.ko.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot driver makes use of regmap, wrapping it with driver specific
operations that are thin wrappers around the core regmap APIs. These are
exported with EXPORT_SYMBOL, dropping the _GPL from the core regmap
exports which is frowned upon. Add _GPL suffixes to at least the APIs that
are doing register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210810123748.47871-1-broonie@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean says:
====================
DSA tagger helpers
The goal of this series is to minimize the use of memmove and skb->data
in the DSA tagging protocol drivers. Unfiltered access to this level of
information is not very friendly to drive-by contributors, and sometimes
is also not the easiest to review.
For starters, I have converted the most common form of DSA tagging
protocols: the DSA headers which are placed where the EtherType is.
The helper functions introduced by this series are:
- dsa_alloc_etype_header
- dsa_strip_etype_header
- dsa_etype_header_pos_rx
- dsa_etype_header_pos_tx
This series is just a resend as non-RFC of v1.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a similar helper for locating the offset to the DSA header
relative to skb->data, and make the existing EtherType header taggers to
use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that protocol tagging driver writers are always surprised about
the formula they use to reach their EtherType header on RX, which
becomes apparent from the fact that there are comments in multiple
drivers that mention the same information.
Create a helper that returns a void pointer to skb->data - 2, as well as
centralize the explanation why that is the case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide away the memmove used by DSA EtherType header taggers to shift the
MAC SA and DA to the left to make room for the header, after they've
called skb_push(). The call to skb_push() is still left explicit in
drivers, to be symmetric with dsa_strip_etype_header, and because not
all callers can be refactored to do it (for example, brcm_tag_xmit_ll
has common code for a pre-Ethernet DSA tag and an EtherType DSA tag).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All header taggers open-code a memmove that is fairly not all that
obvious, and we can hide the details behind a helper function, since the
only thing specific to the driver is the length of the header tag.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit says:
====================
devlink: Control auxiliary devices
Currently, for mlx5 multi-function device, a user is not able to control
which functionality to enable/disable. For example, each PCI
PF, VF, SF function by default has netdevice, RDMA and vdpa-net
devices always enabled.
Hence, enable user to control which device functionality to enable/disable.
This is achieved by using existing devlink params [1] to
enable/disable eth, rdma and vdpa net functionality control knob.
For example user interested in only vdpa device function: performs,
$ devlink dev param set pci/0000:06:00.0 name enable_rdma value false \
cmode driverinit
$ devlink dev param set pci/0000:06:00.0 name enable_eth value false \
cmode driverinit
$ devlink dev param set pci/0000:06:00.0 name enable_vnet value true \
cmode driverinit
$ devlink dev reload pci/0000:06:00.0
Reload command honors parameters set, initializes the device that user
has composed using devlink dev params and resources.
Devices before reload:
mlx5_core.sf.4
(subfunction device)
/\
/| \
/ | \
/ | \
mlx5_core.eth.4 | mlx5_core.rdma.4
(SF eth aux dev) | (SF rdma aux dev)
| | |
| | |
enp6s0f0s88 | mlx5_0
(SF netdev) | (SF rdma device)
|
mlx5_core.vnet.4
(SF vnet aux dev)
|
|
auxiliary/mlx5_core.sf.4
(vdpa net mgmt device)
Above example reconfigures the device with only VDPA functionality.
Devices after reload:
mlx5_core.sf.4
(subfunction device)
/\
/ \
/ \
/ \
mlx5_core.vnet.4 no eth, no rdma aux devices
(SF vnet aux dev)
Above parameters enable user to compose the device as needed based
on the use case.
Since devlink params are done on the devlink instance, these
knobs are uniformly usable for PCI PF, VF and SF devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable user to disable VDPA net auxiliary device so that when it is not
required, user can disable it.
For example,
$ devlink dev param set pci/0000:06:00.0 \
name enable_vnet value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device
mlx5_core.vnet.2 for the VDPA net functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable user to disable RDMA auxiliary device so that when it is not
required, user can disable it.
For example,
$ devlink dev param set pci/0000:06:00.0 \
name enable_rdma value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device
mlx5_core.rdma.2 for the RDMA functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable user to disable Ethernet auxiliary device so that when it is not
required, user can disable it.
For example,
$ devlink dev param set pci/0000:06:00.0 \
name enable_eth value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create mlx5_core.eth.2 auxiliary
device for the Ethernet functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup routine missed to unpublish the parameters. Add it.
Fixes: e890acd5ff ("net/mlx5: Add devlink flow_steering_mode parameter")
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable drivers to publish/unpublish individual parameter.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently device configuration parameters can be registered as an array.
Due to this a constant array must be registered. A single driver
supporting multiple devices each with different device capabilities end
up registering all parameters even if it doesn't support it.
One possible workaround a driver can do is, it registers multiple single
entry arrays to overcome such limitation.
Better is to provide a API that enables driver to register/unregister a
single parameter. This also further helps in two ways.
(1) to reduce the memory of devlink_param_entry by avoiding in registering
parameters which are not supported by the device.
(2) avoid generating multiple parameter add, delete, publish, unpublish,
init value notifications for such unsupported parameters
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create and use a helper function for one parameter registration.
Subsequent patch also will reuse this for driver facing routine to
register a single parameter.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
VDPA net auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_vnet value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
VDPA net functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
RDMA auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_rdma value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
RDMA functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new device generic parameter to enable/disable creation of
Ethernet auxiliary device and associated device functionality
in the devlink instance.
User who prefers to disable such functionality can disable it using below
example.
$ devlink dev param set pci/0000:06:00.0 \
name enable_eth value false cmode driverinit
$ devlink dev reload pci/0000:06:00.0
At this point devlink instance do not create auxiliary device for the
Ethernet functionality.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
net: bridge: vlan: add global mcast options
This is the first follow-up set after the support for per-vlan multicast
contexts which extends global vlan options to support bridge's multicast
config per-vlan, it enables user-space to change and dump the already
existing bridge vlan multicast context options. The global option patches
(01 - 09 and 12-13) follow a similar pattern of changing current mcast
functions to take multicast context instead of a port/bridge directly.
Option equality checks have been added for dumping vlan range compression.
The last 2 patches extend the mcast router dump support so it can be
re-used when dumping vlan config.
patches 01 - 09: add support for various mcast options
patches 10 - 11: prepare for per-vlan querier control
patches 12 - 13: add support for querier control and router control
patches 14 - 15: add support for dumping per-vlan router ports
Next patch-sets:
- per-port/vlan router option config
- iproute2 support for all new vlan options
- selftests
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Embed the standard multicast router port export by br_rports_fill_info()
into a new global vlan attribute BRIDGE_VLANDB_GOPTS_MCAST_ROUTER_PORTS.
In order to have the same format for the global bridge mcast context and
the per-vlan mcast context we need a double-nesting:
- BRIDGE_VLANDB_GOPTS_MCAST_ROUTER_PORTS
- MDBA_ROUTER
Currently we don't compare router lists, if any router port exists in
the bridge mcast contexts we consider their option sets as different and
export them separately.
In addition we export the router port vlan id when dumping similar to
the router port notification format.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are dumping the router ports of a vlan mcast context we need to
use the bridge/vlan and port/vlan's multicast contexts to check if
IPv4/IPv6 router port is present and later to dump the vlan id.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast router state
which is used for the bridge itself. We just need to pass multicast context
to br_multicast_set_router instead of bridge device and the rest of the
logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast querier state.
We just need to pass multicast context to br_multicast_set_querier
instead of bridge device and the rest of the logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a minor optimization and better behaviour to make sure querier and
query sending routines affect only the matching multicast context
depending if vlan snooping is enabled (vlan ctx vs bridge ctx).
It also avoids sending unnecessary extra query packets.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to have the querier state per multicast context in order to have
per-vlan control, so remove the internal option bit and move it to the
multicast context. Also annotate the lockless reads of the new variable.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast startup query
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast query response
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast query interval
option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast querier interval
option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast membership
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast last member
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast startup query
count option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast last member
count option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan IGMP/MLD versions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Elder says:
====================
net: ipa: use runtime PM reference counting
This series does further rework of the IPA clock code so that we
rely on some of the core runtime power management code (including
its referencing counting) instead.
The first patch makes ipa_clock_get() act like pm_runtime_get_sync().
The second patch makes system suspend occur regardless of the
current reference count value, which is again more like how the
runtime PM core code behaves.
The third patch creates functions to encapsulate all hardware
suspend and resume activity. The fourth uses those functions as
the ->runtime_suspend and ->runtime_resume power callbacks. With
that in place, ipa_clock_get() and ipa_clock_put() are changed to
use runtime PM get and put functions when needed.
The fifth patch eliminates an extra clock reference previously used
to control system suspend. The sixth eliminates the "IPA clock"
reference count and mutex.
The final patch replaces the one call to ipa_clock_get_additional()
with a call to pm_runtime_get_if_active(), making the former
unnecessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ipa_clock_get_additional() is a trivial wrapper around
pm_runtime_get_if_active(), just open-code it in its only caller
and delete the function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The runtime power management core code maintains a usage count. This
count mirrors the IPA clock reference count, and there's no need to
maintain both. So get rid of the IPA clock reference count and just
rely on the runtime PM usage count to determine when the hardware
should be suspended or resumed.
Use pm_runtime_get_if_active() in ipa_clock_get_additional(). We
care whether power is active, regardless of whether it's in use, so
pass true for its ign_usage_count argument.
The IPA clock mutex is just used to make enabling/disabling the
clock and updating the reference count occur atomically. Without
the reference count, there's no need for the mutex, so get rid of
that too.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
