Seems to be required by some hardware, wl does it every time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set up tx power for each MRR segment in the tx descriptor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets originally buffered for the regular hardware tx queues can end
up being transmitted through the U-APSD queue (via PS-Poll or U-APSD).
When packets are dropped due to retransmit failures, the pending frames
counter is not always updated properly.
Fix this by keeping track of the queue that a frame was accounted for in
the ath_frame_info struct, and using that on completion to decide
whether the counter should be updated.
This fixes some spurious transmit queue hangs.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like in case of SSB SPROMs they are encoded in a bit tricky way.
SPROM struct already uses s8 type and it's supposed to store decoded
values.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New register area defined in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware sets this register with the offset of the firmware trace area
within the peripheral memory region. Critical for the firmware trace
to work
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use single data source for all information regarding the firmware
memory map. With this change "ucode_xxx" regions disappears since
they are in fact part of larger "upper area" region
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If copy_from_user() fails, buffer allocated for parameters would leak
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variable 'ctx' declarad again in the inner loop. Should use
one from outer loop instead.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New hardware release appears; it require some changes to properly support it.
Introduce struct wil_board and "board" attribute in wil6210_priv;
keep hardware variant information in this structure.
fill it on probe(). Used in the reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unwanted frame types are already handled in 'default' case
of the switch/case below.
The str_ptr is allocated but it can be leaked if the length check
fails in the REQUEST/RESP cases. Fix it by allocating sta_ptr
after the length checks.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Daniel Drake <dsd@laptop.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_p2p_detach() was only called in error flow of the
brcmf_cfg80211_attach() routine, but it also needs to be called
upon brcmf_cfg80211_detach().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of waiting for IFF_UP of the primary net device to determine
the band and channel information of the wiphy structure, this is now
done during driver initialization in brcmf_cfg80211_attach(). The
channel information is obtained from the device and the 2G band is
updated when 40MHz bandwidth is enabled for that band. Before this
change the band and channel objects were common between multiple
brcmfmac devices in the system, which make that information rather
unreliable. That is also fixed with this reworked implementation.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just reordering the functions in preparation of subsequent changes.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introducing a new source module that will be responsible for
identifying features and quirks related to the device being
handled.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparing for another patch move the functions in separate commit.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes firmware path a module parameter so that firmware and
nvram files can be loaded from the specified path.
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reworked the debugfs functions in the driver making it easier for
other driver parts to add a debugfs entry and keeping the information
they want to expose in debugfs private, ie. not in a header.
This is accomplished by providing the function brcmf_debugfs_add_entry()
in which the caller provides a read function in which they provide the
content. The debugfs function will take care of creating the debugfs
entry and cleaning up upon removal.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of seq_file simplifies the debugfs code. Simpler is
better.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up used broadcom IDs, device IDs for all the
bus layers and uses consistent naming for all IDs.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes this typo.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_ptr is used only in an 'if' branch in this function.
Move it to the smaller scope where it is used.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unit of this timeout is in seconds.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'else if' branch never gets the chance as its condition
matches 'if' branch's.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes pending internal scan commands are delayed to give
preference to Tx traffic. 'scan_processing' flag has been
checked at the beginning of delay timer routine to know if in the
meantime scan operation has been cancelled.
There is a corner case where pending scan commands are emptied
after scan_processing flag check is passed. In this case
wrong pointer returned by list_first_entry() is passed to
list_del() which causes system hang.
This patch fixes the issue by adding list_empty() check.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in which rx_reorder_tbl_ptr is accessed
without holding spinlock at few places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The *_bit operations expect unsigned longs.
Instead of casting the pointers, simply define various
bitmaps as unsigned long (instead of u32).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some corner cases with specific timings, we might
try dequeueing tx before we got information about
the link status (e.g. due to recovery during tx).
Instead of NULL dereference, assume all
the links in this case have low priorities.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each 18xx chip contains only 2 real MAC addresses
usable for WLAN, forcing us to use the LAA bit
approach to obtain a third MAC address.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sending the FW a channel switch command on a disconnected
vif may result in a beacon loss event. Avoid this corner case.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the smart config code is in place now,
so register the relevant vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we don't have any actual limitation in the driver, so
increase it arbitrarily to 30 seconds.
The long ROC is needed for the smart config.flow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add defintions and handling for smart config events
(SMART_CONFIG_SYNC_EVENT_ID and SMART_CONFIG_DECODE_EVENT_ID)
parse the relevant info and send it to userspace as
vendor event.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
userspace can ask to perform various smart config
actions via custom vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These commands configures the fw to set key,
enter smart config mode, and exit it.
Add relevant hw ops as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LAA bit is second bit of the MSB, not of the
third byte.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last tx rate calculation didn't take into account
the different indices of 11a and 11g rates tables.
Add the required alignment (count only from the first
11a rate in case of 11a)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On recovery, we increase the current seq num by
WL1271_TX_SQN_POST_RECOVERY_PADDING in order to
compensate for packets we might have missed during
recovery.
It seems that some GEM APs have issues when the
gap is too big, so use a smaller padding in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We want seq num (freed_pkts) to be initialized
on each new connection, but keep persistent
between recoveries/suspends.
Save the freed_pkts in the private block of the
sta struct (we already do a similar thing for
AP's stations).
However, keep the old wlvif->total_freed_pkts
in order to avoid too intrusive change.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx ring index was immediately trimmed with a
bitmask. This discarded the 0xFFFFFFFF error case
(which theoretically can happen when a device is
abruptly disconnected) and led to using an invalid
tx ring index. This could lead to memory
corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible for tx completion not to be
processed. In that case an old stack pointer was
left on copy engine tx ring. Next bmi exchange
would immediately pop it and use complete() on the
completion struct there causing corruption.
Make sure to wait for both tx and rx completions
properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware probing worker failed it called
device_release_driver() which synchronously called
remove() pci callback. The callback in turn waited
for the worker that called it to finish resulting
in a deadlock.
Waiting for a completion instead of a worker, like
some other drivers do, doesn't seem like the best
idea either:
Syscall Worker
probe_fw()
rmmod
dev_lock()
pci->remove()
wait_for_completion()
complete_all()
device_release_driver()
dev_lock()
[sleep]
free(ar)
dev_unlock()
[resume]
There's no guarantee that Worker upon resuming can
still access any data/code of the module.
Leaving device bound to a driver is not as harmful
as deadlocking so remove the call to
device_release_driver() while a proper solution is
figured out.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This change enables ath6kl driver to support ar6004 hw3.0. At the same time do
some fixes in firmware initialisation which applies to ar6004 hw1.3 as well.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the firmware versions support rate tables up to mcs15, add support for
that.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rx flush was not implemented for htc pipe, add that now. Doesn't fix any known
issues.
Also free the skb if htc control messages get canceled.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The functionality defined through these flags were actually firmware features
which can change between firmware versions. To make it possible to support
different firmware versions with the same driver, convert the flags to firmware
feature flags.
For backwards compatibility support for old ar6004 firmware FW
API 3 or smaller images we forcefully set the feature bits in the driver.
Starting from FW API 5 the firmware image needs to set them.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
tmp may be used uninitialized if ath6kl_bmi_read() returns an error.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.
Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows adding more revisions support, spotting lacking tables and
unifies naming schema.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment was not accurate, we are talking about the frames
*for* the station and not from the station.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch removes the setting of the ADC sampling bits in
the mvm nic configuration. This setting is not required by
the firmware, and furthermore - it interferes with the DBGC
when it is running in DRAM mode on PCIe.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The FW currently doesn't optimally support TDLS in DCM mode. Teardown
all TDLS peers when we have more than a single phy context.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The FW does not support PSM on a vif with associated TDLS peers. Disable
PSM when the first peer joins and re-enable it when the last leaves.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the new mac80211 callback to protect a TDLS discovery session so we
can hear the discovery-response packet.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
HW/FW constraints dictate that TDLS should only be used when a single
phy ctx is active. We also support at most 4 TDLS peers. We don't
support TDLS on a P2P vif.
Unify and move a phy-ctx counting implementation from the power-mgmt code
in order to simplify implementation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
An AP/GO may perform the channel switch slightly before its stations.
This scenario may result in packet loss, since the transmission may start
before the client is actually on a new channel. In order to prevent
potential packet loss disable tx to all the stations when the channel
switch flow starts. Clear the disable_tx bit when a station is seen on a
target channel, or after IWL_MVM_CS_UNBLOCK_TX_TIMEOUT beacons on a new
channel. In addition call ieee80211_sta_block_awake in order to inform
mac80211 that the frames for this station should be buffered.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to the spec, GO/AP should perform the channel switch just
before "beacon 0". However, since the exact timing isn't defined,
it may result in a sudden GO disappearance from the channel.
Prevent potential packet loss when performing the CS by scheduling
NoA time event and executing the channel switch flow when a notification
from fw is received.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently mvm->csa_vif is protected with mvm mutex. The RCU protection
is required for "iwlwifi: mvm: Reflect GO channel switch in NoA" patch.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Call ieee80211_beacon_get_template instead of ieee80211_beacon_get and sync the
CSA counters with mac80211 after each beacon transmission.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement support for unbind-bind flow for the client roles. This
includes telling the firmware that we are not associated, removing
time-events, removing quotas and updating power management during the
actual switch, and redoing everything in the new channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement the switch_vif_chanctx operation with support for a
single-vif and SWAP mode. The REASSIGN mode and multi-vifs are not
supported yet.
This operation needs to implement 4 steps, namely unassign, remove,
add and assign the chanctx. In order to do this, split out these
operations into locked and non-locked parts, thus allowing us to call
them while locked.
Additionally, in order to allow us to restart the hardware when
something fails, add a boolean to the iwl_mvm_nic_restart() function
that tells whether the restart was triggered by a FW error or
something else.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.
Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Simplify the quota iterator by not passing the update type,
it only needs to know whether or not to skip an interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware currently deals with zero quota for a given
binding, but it seems odd to send that down. Make sure
that we don't do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are some cases where we can currently send zero quota
for a valid binding, e.g. if we update while an interface is
bound to a channel context but not yet acting as an AP.
Avoid this by reordering the checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily. In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when driver takes the MAC address from the HW section and
it isn't valid - print an error.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These file are removed recursively anyway, so there's no
point saving them just to redundantly remove them later.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_rs_rate_init() is called multiple times to re-init
the rate scaling statistics (e.g. after some idle time).
It clears all the lq_sta sta, including some fields that
shouldn't be cleared (e.g. debugfs pointers). Fix it
by adding a new 'persistent' sub-struct, and
avoid clearing it on (re-)init.
Move the initialization of the persistent fields to
rs_alloc_sta instead.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
