intel_lpm_suspend/resume are only used in case of CONFIG_PM.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement runtime PM suspend/resume callbacks.
If LPM supported, controller is put into supsend after a delay of
inactivity (1s). Inactivity is based on LPM idle notification and
host TX traffic.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add PM suspend/resume callbacks which call lpm_suspend/resume.
Add LPM ack in threaded IRQ handler to notify the controller that
resume is complete.
Protect hci_uart against concurrent removing during suspend/resume.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add LPM PM suspend/resume/host_wake LPM functions.
A LPM transaction is composed with a LPM request and ack/response.
Host can send a LPM suspend/resume request to the controller which
should respond with a LPM ack.
If resume is requested by the controller (irq), host has to send a LPM
ack once resumed.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Replace the device_intel list spinlock with a mutex.
devm_request_threaded_irq is not atomic and upcomming PM support should
be simpler.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable controller Low-Power-Mode if we have a pdev to manage host
wake-up. Once LPM is enabled, controller notifies its TX status via
a vendor specific packet (tx_idle/tx_active).
tx_active means that there is more data upcoming from controller.
tx_idle means that controller can be put in suspended state.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
An IRQ can be retrieved from the pdev resources. This irq will be used
in case of LPM suspend mode to wake-up the host and resume the link.
This resource can be declared as a GPIO-Interrupt which requires to be
converted into IRQ.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
A platform device can be used to provide some specific resources in
order to manage the controller. In this first patch we retrieve the
reset gpio which is used to power on/off the controller.
The main issue is to match the current tty with the correct pdev.
In case of ACPI, we can easily find the right tty/pdev pair because
they are both child of the same UART port.
If controller is powered-on from the driver, we need to wait for a
HCI boot event before being able to send any command.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement the set_baudrate callback for hci_intel.
- Controller requires a read Intel version command before updating
its baudrate.
- The operation consists in an async cmd since the controller does
not respond at the same speed.
- Wait 100ms to let the controller change its baudrate.
- Clear RTS until we change our own UART speed
Manage speed change in the setup function, we need to restore the oper
speed once chip has booted on patched firmware.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Intel version information is shared between USB and UART drivers
and with that move it into a generic function of the Intel module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Secure Send command is used the same in USB and UART drivers
and with that move a generic version into the Intel module.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel specific Bluetooth module provides support for pubic address
configuration. So make sure that it is enabled for Intel UART devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Intel Lightning Peak devices do not come with Bluetooth firmware
loaded and thus require a full download of the operational Bluetooth
firmware when the device is attached via the Bluetooth line discipline.
Lightning Peak devices start with a bootloader mode that only accepts
a very limited set of HCI commands. The supported commands are enough
to identify the hardware and select the right firmware to load.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth address setting for Intel devices is provided by a generic
module now. Start using that module instead of relying it being included
in the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using vendor detection, this adds support for the Intel specific
address configuration command.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
