Turns out latest upstream U-Boot does not configure/enable pll_u which
leaves it at some default rate of 500 kHz:
root@apalis-t30:~# cat /sys/kernel/debug/clk/clk_summary | grep pll_u
pll_u 3 3 0 500000 0
Of course this won't quite work leading to the following messages:
[ 6.559593] usb 2-1: new full-speed USB device number 2 using tegra-
ehci
[ 11.759173] usb 2-1: device descriptor read/64, error -110
[ 27.119453] usb 2-1: device descriptor read/64, error -110
[ 27.389217] usb 2-1: new full-speed USB device number 3 using tegra-
ehci
[ 32.559454] usb 2-1: device descriptor read/64, error -110
[ 47.929777] usb 2-1: device descriptor read/64, error -110
[ 48.049658] usb usb2-port1: attempt power cycle
[ 48.759475] usb 2-1: new full-speed USB device number 4 using tegra-
ehci
[ 59.349457] usb 2-1: device not accepting address 4, error -110
[ 59.509449] usb 2-1: new full-speed USB device number 5 using tegra-
ehci
[ 70.069457] usb 2-1: device not accepting address 5, error -110
[ 70.079721] usb usb2-port1: unable to enumerate USB device
Fix this by actually allowing the rate also being set from within
the Linux kernel.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently VDE clock rate is determined by clock config left from
bootloader, let's not rely on it and explicitly specify the clock
rate in the CCF driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PLL_C_OUT_1 can't produce 216 MHz defined in the init_table. Let's
set it to 240 MHz and explicitly specify HCLK rate for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Machine dies if HCLK, SCLK or EMC is disabled. Hence mark these clocks
as critical.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: <stable@vger.kernel.org> # v4.16
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adding these EPLL output frequency entries allows to support all required
audio sample rates on the CODEC and the HDMI interface on Peach-Pit
Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This allows changing the EPLL output frequency through the audio subsystem
clock tree leaf clocks. This change is needed to support audio on the HDMI
interface on Peach-Pi(t) Chromebook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
It's found that the final phase set by driver doesn't match that of
the output from clk_summary:
dwmmc_rockchip fe310000.dwmmc: Successfully tuned phase to 346
mmc0: new ultra high speed SDR104 SDIO card at address 0001
cat /sys/kernel/debug/clk/clk_summary | grep sdio_sample
sdio_sample 0 1 0 50000000 0 0
It seems the cached core->phase isn't updated after the clk was
registered. So fix this issue by updating the core->phase if setting
phase successfully.
Fixes: 9e4d04adeb ("clk: add clk_core_set_phase_nolock function")
Cc: Stable <stable@vger.kernel.org>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
RCC manages clock for debug and trace.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Two micro-controller clock output (MCO) pins are available:
MCO1 and MCO2.
For each output, it is possible to select a clock source.
The selected clock can be divided thanks to configurable
prescaler.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each peripheral requires a bus interface clock.
Some peripherals need also a dedicated clock for their communication
interface, this clock is generally asynchronous with respect to the bus
interface clock (peripheral clock), and is named kernel clock.
For each IP, Peripheral clock and Kernel are generally gating with same
gate. Also, Kernel clocks can share a same multiplexer.
This patch introduces a mechanism to manage a gate with several
clocks and to manage a shared multiplexer (mgate and mmux).
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds Kernel timers.
This patch adds timers kernel clock.
Timers are gather into two groups corresponding to the APB bus
they are attached to.
Each group has its own prescaler, managed in this patch.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The RCC handles three sub-system clocks: ck_mpuss, ck_axiss
and ck_mcuss.
This patch adds also some MUX system and several prescalers.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Each PLL has 3 outputs with post-dividers.
pll1_p is dedicated for Cortex-A7
pll1_q is not connected
pll1_r is not connected
pll2_p is dedicated for AXI
pll2_q is dedicated for GPU
pll2_r is dedicated for DDR
pll3_p is dedicated for mcu
pll3_q is for Peripheral Kernel Clock
pll3_r is for Peripheral Kernel Clock
pll4_p is for Peripheral Kernel Clock
pll4_q is for Peripheral Kernel Clock
pll4_r is for Peripheral Kernel Clock
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
STMP32MP1 has 4 PLLs.
PLL supports integer and fractional mode.
Each PLL has 3 output dividers (p, q, r)
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch adds source clocks for PLLs
This patch also introduces MUX clock API.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
MP1 Gate is a gate with a set and a clear register.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch introduces the mechanism to probe stm32mp1 driver.
It also defines registers definition.
This patch also introduces the generic mechanism to register
a clock (a simple gate, divider and fixed factor).
All clocks will be defined in one table.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Tegra210 has a hw bug which can cause IP blocks to lock up when ungating a
domain. The reason is that the logic responsible for resetting the memory
built-in self test mode can come up in an undefined state because its
clock is gated by a second level clock gate (SLCG). Work around this by
making sure the logic will get some clock edges by ensuring the relevant
clock is enabled and temporarily override the relevant SLCGs.
Unfortunately for some IP blocks, the control bits for overriding the
SLCGs are not in CAR, but in the IP block itself. This means we need to
map a few extra register banks in the clock code.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
fixup mbist
To ensure writes to clock registers have properly propagated through the
clock control logic and state machines, we need to ensure the writes have
been posted in the registers and wait for 1us after that.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is needed by the memory built-in self test work around.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Hector Martin <marcan@marcan.st>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to id.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Certain clkctrl clocks, notably the display ones, use the
CLK_SET_RATE_PARENT feature extensively. Add support for this flag
to the clkctrl clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Display driver assumes it can use clk_set_rate for the display clock
via set-rate-parent mechanism, so add the flag for this to it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Currently, the driver contains a large hints table for clocks that exist
on a device, however, it is possible to probe the clocks from the firmware
also. Add support for this, and drop the clock hints table support from
the driver completely. This causes the driver to send a few extra sci-clk
messages during boot, basically one extra for each device that exists on
the SoC; on K2G this is approx 80.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the mux clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Latching the clock settings is needed with certain clocks, where
the setting is "cached" in HW before doing the actual re-programming
of the clock source. This patch adds support for clock latching to
the divider clock.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Certain clocks require latching to be done, so that the actual
settings get updated on the HW that generates the clock signal.
One example of such a clock is the dra76x GMAC DPLL H14 output,
which requires its divider settings to be latched when updated.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Useful for changing few bits on a register, this makes sure for example
that the operation is done atomically in case of syscon.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Clocks related to DISP1 block require special handling for power domain
turn on/off sequences. Till now this was handled by Exynos power domain
driver, but that approach was limited only to some special cases. This
patch moves handling of those operations to clock controller driver.
This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5250 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Clocks related to DISP, GSC and MFC blocks require special handling for
power domain turn on/off sequences. Till now this was handled by Exynos
power domain driver, but that approach was limited only to some special
cases. This patch moves handling of those operations to clock controller
driver. This gives more flexibility and allows fine tune values of some
clock-specific registers. This patch moves handling of those mentioned
clocks to Exynos5 sub-CMU driver instantiated from Exynos5420 driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Exynos5250/5420/5800 have only one clock controller, but some of their
clock depends on respective power domains. Handling integration of clock
controller and power domain can be done using runtime PM feature of CCF
framework. This however needs a separate struct device for each power
domain. This patch adds such separate driver for a group of such clocks,
which can be instantiated more than once, each time for a different
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The MMC sample and drv clock for rockchip platforms are derived from
the bus clock output to the MMC/SDIO card. So it should never happens
that the clk rate is zero given it should inherits the clock rate from
its parent. If something goes wrong and makes the clock rate to be zero,
the calculation would be wrong but may still make the mmc tuning process
work luckily. However it makes people harder to debug when the following
data transfer is unstable.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
rockchip_clk_register_branch() and rockchip_clk_register_frac_branch()
should free the memory internally when seeing any failure.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
CLK_PLL_VIDEO needs to be referenced in HDMI DT entry as a possible
PHY clock parent.
Export it so it can be used later in DT.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some units have to be able to set it's own clock precisely to work
correctly. Allow them to do so by adding CLK_SET_RATE_PARENT flag.
Add this flag to DE, TCON and HDMI clocks.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Although user manuals for H3 and H5 SoCs state that minimal rate
supported by video PLL is around 30 MHz, it seems that in reality
minimal rate is around 192 MHz.
Experiments showed that any rate below 96 MHz doesn't produce any video
output at all. Even at this frequency, stable output depends on right
factors. For example, when N = 4 and M = 1, output is stable and when N
= 8 and M = 2, it's not.
BSP clock driver suggest that minimum stable frequency is 192 MHz. That
would also be in line with A64 SoC, which has similar periphery.
Set minimal video PLL rate for H3/H5 to 192 MHz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some NM PLLs doesn't work well when their output clock rate is set below
certain rate.
Add support for that constrain.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is a test divider and post divider in video PLL,
test divider is placed before post divider, all clocks
that can select parent from video PLL should be from
post divider, NOT from pll_video_main, below are
clock tree dump before and after this patch:
Before:
pll_video_main
pll_video_main_bypass
pll_video_main_clk
lcdif_pixel_src
lcdif_pixel_cg
lcdif_pixel_pre_div
lcdif_pixel_post_div
lcdif_pixel_root_clk
After:
pll_video_main
pll_video_main_bypass
pll_video_main_clk
pll_video_test_div
pll_video_post_div
lcdif_pixel_src
lcdif_pixel_cg
lcdif_pixel_pre_div
lcdif_pixel_post_div
lcdif_pixel_root_clk
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On some ARM based systems, a separate Cortex-M based System Control
Processor(SCP) provides the overall power, clock, reset and system
control. System Control and Management Interface(SCMI) Message Protocol
is defined for the communication between the Application Cores(AP)
and the SCP.
This patch adds support for the clocks provided by SCP using SCMI
protocol.
Cc: linux-clk@vger.kernel.org
Cc: Michael Turquette <mturquette@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
According to the i.MX7D Reference Manual, the Keypad Port module
(KPP) requires this clock gate to be enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock COMBPHY1 has already been supported by hi3798cv200 driver,
but COMBPHY0 is missing. It adds COMBPHY0 clock support.
Since the mux table is being shared by COMBPHY0 and COMBPHY1, it renames
comphy1_mux_p and comphy1_mux_table a bit to drop instance number '1'
from there.
Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's a coding-style fix, which corrects the indentation for all those
clock definitions, so that the code looks nicer and new definitions can
be added with a recommended indentation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clock HISTB_USB2_OTG_UTMI_CLK is defined by device tree bindings in
include/dt-bindings/clock/histb-clock.h, but hasn't been supported by
hi3798cv200 clock driver. Let's add the support for it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The IR clock is sourced from '24m' rather than '100m'. Correct it.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The unregister call sequence in error path of function
hi3798cv200_clk_register() should be opposite to the order of register
calls. Let's reverse the call sequence to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Initial support for R-Car M3-N (r8a77965), including core and module
clocks.
Based on Table 8.2d of "R-Car Series, 3rd Generation User's Manual:
Hardware (Rev. 0.80, Oct 31, 2017)".
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. To avoid possible mistakes we can use compile
time validation.
The patch introduces such validators and expands all initializers
with additional input frequency parameter, required to validate rates.
Since S3C24xx PLLs requires different validators two new macros have
been introduced to deal with it. Also, since PLLs 4502 and 4508 have
different formulas PLL_45XX_RATE has been replaced with PLL_4508_RATE.
As the patch adds only compile time validators it should not have impact
on compiled code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated from
the PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Rates declared in PLL rate tables should match exactly rates calculated
from PLL coefficients. If that is not the case, rate of the PLL's child clock
might be set not as expected. For instance, if in the PLL rates table we have
a 393216000 Hz entry and the real value as returned by the PLL's recalc_rate
callback is 393216003, after setting PLL's clk rate to 393216000 clk_get_rate
will return 393216003. If we now attempt to set rate of a PLL's child divider
clock to 393216000/2 its rate will be 131072001, rather than 196608000.
That is, the divider will be set to 3 instead of 2, because 393216003/2 is
greater than 196608000.
To fix this issue declared rates are changed to exactly match rates generated
by the PLL, as calculated from the P, M, S, K coefficients.
In this patch an erroneous P value for 74176002 output frequency is also
corrected.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
According to the i.MX7D Reference Manual,
SNVS block has a clock gate, accessing SNVS block
would need this clock gate to be enabled, add it
into clock tree so that SNVS module driver can
operate this clock gate.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add R-Car V3H (R8A77980) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 code.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7792_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Add "rwdt" clock to r8a7794_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7791_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7790_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7745_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add "rwdt" clock to r8a7743_mod_clks. Also, since we may need to access
the watchdog registers at any time, declare the clock as critical.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When support for the A31/A31s CCU was first added, the clock ops for
the CLK_OUT_* clocks was set to the wrong type. The clocks are MP-type,
but the ops was set for div (M) clocks. This went unnoticed until now.
This was because while they are different clocks, their data structures
aligned in a way that ccu_div_ops would access the second ccu_div_internal
and ccu_mux_internal structures, which were valid, if not incorrect.
Furthermore, the use of these CLK_OUT_* was for feeding a precise 32.768
kHz clock signal to the WiFi chip. This was achievable by using the parent
with the same clock rate and no divider. So the incorrect divider setting
did not affect this usage.
Commit 946797aa3f ("clk: sunxi-ng: Support fixed post-dividers on MP
style clocks") added a new field to the ccu_mp structure, which broke
the aforementioned alignment. Now the system crashes as div_ops tries
to look up a nonexistent table.
Reported-by: Philipp Rossak <embed3d@gmail.com>
Tested-by: Philipp Rossak <embed3d@gmail.com>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When parent rate is 24MHz and multiplier N >= 180, intermediate clock
rate doesn't fit in 32 bit variable anymore.
Because of that, introduce function for calculating clock rate which
uses 64 bit variable for intermediate result.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Currently, if one of the factors isn't present, bit 0 gets always set to
1. For example, A83T has NMP PLLs modelled as NKMP PLL without K. Since
K is not specified, it's offset, width and shift is 0. Driver assumes
that lowest value possible is 1, otherwise we would get division by 0.
That situation causes that bit 0 is always set, which may change wanted
clock rate.
Fix that by masking every factor according to it's specified width.
Factors with width set to 0 won't have any influence to final register
value.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add one more entry to the exynos5433_aud_pll_rates table, this allows
to support audio sample rates: 48000, 96000, 192000 Hz with minimum
error. The M, P, S, K values re confirmed by the HW team.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
The sclk_ioclk_i2s1_bclk clock is not currently handled by any driver
and disabling this clock by the clk core prevents proper operation
of the I2S1 block. CLK_IGNORE_UNUSED flag is added as a temporary fix.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
There is a error message within devm_ioremap_resource already,
so remove the dev_err call to avoid redundant error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch just removes the unneeded enumeration for PLL index.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The following symbols:
SUNXI_CCU_DIV
SUNXI_CCU_MULT
SUNXI_CCU_NK
SUNXI_CCU_NKM
SUNXI_CCU_NM
SUNXI_CCU_MP
SUNXI_CCU_PHASE
were removed with the commit 06e226c7fb ("clk: sunxi-ng: Move all clock types to a library")
So selecting them is useless.
Fixes: c84f5683f6 ("clk: sunxi-ng: Add sun4i/sun7i CCU driver")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds Z clock for R8A7796 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Z clock for R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds Z clock divider support for R-Car Gen3 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since v4.15-rc1, the DTS files for all R-Car Gen2 SoCs have been
converted to the new CPG/MSSR bindings. Hence it is now safe to no
longer enable legacy DT clock support by default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
dclk_lcdc can be sourced from a general pll source as well
as the hdmiphy's pll output. We will want to set this source
by hand (to the system-pll-source in most cases) and also
want rate changes to this clock to be able to also touch
the pll source clock if needed, so add CLK_SET_RATE_PARENT
and CLK_SET_RATE_NO_REPARENT for dclk_lcdc.
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
[ammended commit message]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
NIU clocks are supplying the interconnect connections to specific
peripherals and are currently not controlled in any way.
So to prevent things falling apart at strange moments, mark all
niu clocks as critical.
Most of them where marked as CLK_IGNORE_UNUSED, but that doesn't
help if a parent clock then gets disabled.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The clock wrongly was called hclk_vio and exported, while it actually is
a clock of the interconnect-vio connection and should therefore be always
on till we actually model the interconnect.
So fix that and don't export it as HCLK_VIO.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On axg, the rate of the mpll is stuck as if sdm value was 4 and could not
change (expect for mpll2 strangely). Looking at the vendor kernel, it
turns out a new magic bit from the undocumented HHI_PLL_TOP_MISC register
is required.
Setting this bit solves the problem and the mpll rates are back to normal
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the datasheet, the od shift of sys_pll is actually 16.
Fixes: 78b4af312f ('clk: meson-axg: add clock controller drivers')
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[fixed commit message]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The fixed_pll also has a fractional part. On axg s400 board, without
this parameter, the calculated rate is off by ~8Mhz (0,4%). The fixed_pll
being the root of the peripheral clock tree, this error is propagated to
the rest of the clocks
Adding the definition of the parameter fixes the problem
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The fixed_pll of gxbb and gxl also has a fractional parameter. This has
not been a problem so far because the fractional part is actually set
to 0 on these platforms, so the rate remains correct when it is ignored.
Still, it is better represent the pll the way it is, so add the frac
parameter now
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The rate of the parent should not be multiplied by 2 when the pll has a
fractional part. This is making the rate calculation of the gxl_hdmi_pll
wrong (and others as well). This multiplication is specific
to the hdmi_pll of gxbb and is most likely due to a multiplier sitting
in front of this particular pll.
Add a fixed factor clock in front on the gxbb pll and remove this constant
from the calculation to fix the problem
Fixes: 4a47295144 ("clk: meson: fractional pll support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The hdmi pll used in the gxl family is actually different from the gxbb
one. The register layout is completely different, which explain why the
hdmi pll rate has always been rubbish on the gxl family.
Adding the correct register field is the first part of the fix to get a
correct rate out the hdmi pll
Fixes: 0d48fc558d ("clk: meson-gxbb: Add GXL/GXM GP0 Variant")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Some meson plls, such as the hdmi pll, are using a 3rd od parameter,
which is yet another "power of 2" post divider. Add it to fix the
calculation of the hdmi_pll rate
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Use the fractional part width in the calculation instead of 12, which
happens to be the witdh right now. This is safer in case the field width
ever change in the future
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The pll driver performs the rate calculation in Mhz, which adds an
unnecessary rounding down to the Mhz of the rate. Use 64bits long
integers to perform this calculation safely on meson8b and perform the
calculation in Hz instead
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Read-only plls don't need param table to recalculate the rate.
Providing them with a param table is just a waste of memory.
Remove the useless tables from sys_pll on gxbb and axg.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Make sure the rate param table is available before using it.
Some read-only plls don't provide it, which is ok since the
table is not used by read-only clocks. R/W clocks are supposed
to provide it, but it does not hurt check it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
These are the main MIPS changes for 4.16. Rough overview:
- Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
- Support for the Ranchu board (used by Android emulator)
- Various cleanups and misc improvements
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA operations
on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of "MEM_RESERVED"
-----BEGIN PGP SIGNATURE-----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=7iwT
-----END PGP SIGNATURE-----
Merge tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips
Pull MIPS updates from James Hogan:
"These are the main MIPS changes for 4.16.
Rough overview:
(1) Basic support for the Ingenic JZ4770 based GCW Zero open-source
handheld video game console
(2) Support for the Ranchu board (used by Android emulator)
(3) Various cleanups and misc improvements
More detailed summary:
Fixes:
- Fix generic platform's USB_*HCI_BIG_ENDIAN selects (4.9)
- Fix vmlinuz default build when ZBOOT selected
- Fix clean up of vmlinuz targets
- Fix command line duplication (in preparation for Ingenic JZ4770)
Miscellaneous:
- Allow Processor ID reads to be to be optimised away by the compiler
(improves performance when running in guest)
- Push ARCH_MIGHT_HAVE_PC_SERIO/PARPORT down to platform level to
disable on generic platform with Ranchu board support
- Add helpers for assembler macro instructions for older assemblers
- Use assembler macro instructions to support VZ, XPA & MSA
operations on older assemblers, removing C wrapper duplication
- Various improvements to VZ & XPA assembly wrappers
- Add drivers/platform/mips/ to MIPS MAINTAINERS entry
Minor cleanups:
- Misc FPU emulation cleanups (removal of unnecessary include, moving
macros to common header, checkpatch and sparse fixes)
- Remove duplicate assignment of core in play_dead()
- Remove duplication in watchpoint handling
- Remove mips_dma_mapping_error() stub
- Use NULL instead of 0 in prepare_ftrace_return()
- Use proper kernel-doc Return keyword for
__compute_return_epc_for_insn()
- Remove duplicate semicolon in csum_fold()
Platform support:
Broadcom:
- Enable ZBOOT on BCM47xx
Generic platform:
- Add Ranchu board support, used by Android emulator
- Fix machine compatible string matching for Ranchu
- Support GIC in EIC mode
Ingenic platforms:
- Add DT, defconfig and other support for JZ4770 SoC and GCW Zero
- Support dynamnic machine types (i.e. JZ4740 / JZ4770 / JZ4780)
- Add Ingenic JZ4770 CGU clocks
- General Ingenic clk changes to prepare for JZ4770 SoC support
- Use common command line handling code
- Add DT vendor prefix to GCW (Game Consoles Worldwide)
Loongson:
- Add MAINTAINERS entry for Loongson2 and Loongson3 platforms
- Drop 32-bit support for Loongson 2E/2F devices
- Fix build failures due to multiple use of 'MEM_RESERVED'"
* tag 'mips_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/mips: (53 commits)
MIPS: Malta: Sanitize mouse and keyboard configuration.
MIPS: Update defconfigs after previous patch.
MIPS: Push ARCH_MIGHT_HAVE_PC_SERIO down to platform level
MIPS: Push ARCH_MIGHT_HAVE_PC_PARPORT down to platform level
MIPS: SMP-CPS: Remove duplicate assignment of core in play_dead
MIPS: Generic: Support GIC in EIC mode
MIPS: generic: Fix Makefile alignment
MIPS: generic: Fix ranchu_of_match[] termination
MIPS: generic: Fix machine compatible matching
MIPS: Loongson fix name confict - MEM_RESERVED
MIPS: bcm47xx: enable ZBOOT support
MIPS: Fix trailing semicolon
MIPS: Watch: Avoid duplication of bits in mips_read_watch_registers
MIPS: Watch: Avoid duplication of bits in mips_install_watch_registers.
MIPS: MSA: Update helpers to use new asm macros
MIPS: XPA: Standardise readx/writex accessors
MIPS: XPA: Allow use of $0 (zero) to MTHC0
MIPS: XPA: Use XPA instructions in assembly
MIPS: VZ: Pass GC0 register names in $n format
MIPS: VZ: Update helpers to use new asm macros
...
to the clk rate protection support added by Jerome Brunet. This feature
will allow consumers to lock in a certain rate on the output of a clk so
that things like audio playback don't hear pops when the clk frequency
changes due to shared parent clks changing rates. Currently the clk
API doesn't guarantee the rate of a clk stays at the rate you request
after clk_set_rate() is called, so this new API will allow drivers
to express that requirement. Beyond this, the core got some debugfs
pretty printing patches and a couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h file
causes small one-liners in all the architecture Kbuild files. Overall, the
driver diff seems to be the normal stuff that comes all the time to
fix little problems here and there and to support new hardware.
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=bGPp
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework has a handful of patches this time around, mostly
due to the clk rate protection support added by Jerome Brunet.
This feature will allow consumers to lock in a certain rate on the
output of a clk so that things like audio playback don't hear pops
when the clk frequency changes due to shared parent clks changing
rates. Currently the clk API doesn't guarantee the rate of a clk stays
at the rate you request after clk_set_rate() is called, so this new
API will allow drivers to express that requirement.
Beyond this, the core got some debugfs pretty printing patches and a
couple minor non-critical fixes.
Looking outside of the core framework diff we have some new driver
additions and the removal of a legacy TI clk driver. Both of these hit
high in the dirstat. Also, the removal of the asm-generic/clkdev.h
file causes small one-liners in all the architecture Kbuild files.
Overall, the driver diff seems to be the normal stuff that comes all
the time to fix little problems here and there and to support new
hardware.
Summary:
Core:
- Clk rate protection
- Symbolic clk flags in debugfs output
- Clk registration enabled clks while doing bookkeeping updates
New Drivers:
- Spreadtrum SC9860
- HiSilicon hi3660 stub
- Qualcomm A53 PLL, SPMI clkdiv, and MSM8916 APCS
- Amlogic Meson-AXG
- ASPEED BMC
Removed Drivers:
- TI OMAP 3xxx legacy clk (non-DT) support
- asm*/clkdev.h got removed (not really a driver)
Updates:
- Renesas FDP1-0 module clock on R-Car M3-W
- Renesas LVDS module clock on R-Car V3M
- Misc fixes to pr_err() prints
- Qualcomm MSM8916 audio fixes
- Qualcomm IPQ8074 rounded out support for more peripherals
- Qualcomm Alpha PLL variants
- Divider code was using container_of() on bad pointers
- Allwinner DE2 clks on H3
- Amlogic minor data fixes and dropping of CLK_IGNORE_UNUSED
- Mediatek clk driver compile test support
- AT91 PMC clk suspend/resume restoration support
- PLL issues fixed on si5351
- Broadcom IProc PLL calculation updates
- DVFS support for Armada mvebu CPU clks
- Allwinner fixed post-divider support
- TI clkctrl fixes and support for newer SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (125 commits)
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: fix reentrancy of clk_enable() on UP systems
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: renesas: r8a7796: Add FDP clock
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
clk: Improve flags doc for of_clk_detect_critical()
arch: Remove clkdev.h asm-generic from Kbuild
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: Prepare to remove asm-generic/clkdev.h
...
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
* clk-aspeed:
clk: aspeed: Handle inverse polarity of USB port 1 clock gate
clk: aspeed: Fix return value check in aspeed_cc_init()
clk: aspeed: Add reset controller
clk: aspeed: Register gated clocks
clk: aspeed: Add platform driver and register PLLs
clk: aspeed: Register core clocks
clk: Add clock driver for ASPEED BMC SoCs
dt-bindings: clock: Add ASPEED constants
* clk-lock-UP:
clk: fix reentrancy of clk_enable() on UP systems
* clk-mediatek:
clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built
clk: mediatek: Fix all warnings for missing struct clk_onecell_data
clk: mediatek: fixup test-building of MediaTek clock drivers
clk: mediatek: group drivers under indpendent menu
* clk-allwinner:
clk: sunxi-ng: a83t: Add M divider to TCON1 clock
clk: sunxi-ng: fix the A64/H5 clock description of DE2 CCU
clk: sunxi-ng: add support for Allwinner H3 DE2 CCU
dt-bindings: fix the binding of Allwinner DE2 CCU of A83T and H3
clk: sunxi-ng: sun8i: a83t: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: sun8i: a83t: Add /2 fixed post divider to audio PLL
clk: sunxi-ng: Support fixed post-dividers on NM style clocks
clk: sunxi-ng: sun50i: a64: Add 2x fixed post-divider to MMC module clocks
clk: sunxi-ng: Support fixed post-dividers on MP style clocks
clk: sunxi: Use PTR_ERR_OR_ZERO()
* clk-remove-asm-clkdev:
clk: Move __clk_{get,put}() into private clk.h API
clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks
arch: Remove clkdev.h asm-generic from Kbuild
clk: Prepare to remove asm-generic/clkdev.h
blackfin: Use generic clkdev.h header
* clk-debugfs-fixes:
clk: Simplify debugfs registration
clk: Fix debugfs_create_*() usage
clk: Show symbolic clock flags in debugfs
clk: Improve flags doc for of_clk_detect_critical()
* clk-renesas:
clk: renesas: r8a7796: Add FDP clock
clk: renesas: cpg-mssr: Keep wakeup sources active during system suspend
clk: renesas: mstp: Keep wakeup sources active during system suspend
clk: renesas: r8a77970: Add LVDS clock
* clk-meson:
clk: meson-axg: fix potential NULL dereference in axg_clkc_probe()
clk: meson-axg: make local symbol axg_gp0_params_table static
clk: meson-axg: fix return value check in axg_clkc_probe()
clk: meson: mpll: use 64-bit maths in params_from_rate
clk: meson-axg: add clock controller drivers
clk: meson-axg: add clocks dt-bindings required header
dt-bindings: clock: add compatible variant for the Meson-AXG
clk: meson: make the spinlock naming more specific
clk: meson: gxbb: remove IGNORE_UNUSED from mmc clocks
clk: meson: gxbb: fix wrong clock for SARADC/SANA
* clk-iproc:
clk: iproc: Minor tidy up of iproc pll data structures
clk: iproc: Allow plls to do minor rate changes without reset
clk: iproc: Fix error in the pll post divider rate calculation
clk: iproc: Allow iproc pll to runtime calculate vco parameters
* clk-mvebu:
clk: mvebu: armada-37xx-periph: Use PTR_ERR_OR_ZERO()
* clk-qcom-a53:
clk: qcom: Add APCS clock controller support
clk: qcom: Add regmap mux-div clocks support
clk: qcom: Add A53 PLL support
* clk-at91:
clk: at91: pmc: Support backup for programmable clocks
clk: at91: pmc: Save SCSR during suspend
clk: at91: pmc: Wait for clocks when resuming
* clk-imx7ulp:
clk: Don't touch hardware when reparenting during registration
* clk-axigen:
clk: axi-clkgen: Round closest in round_rate() and recalc_rate()
clk: axi-clkgen: Correctly handle nocount bit in recalc_rate()
* clk-si5351:
clk: si5351: _si5351_clkout_reset_pll() can be static
clk: si5351: Do not enable parent clocks on probe
clk: si5351: Rename internal plls to avoid name collisions
clk: si5351: Apply PLL soft reset before enabling the outputs
clk: si5351: Add DT property to enable PLL reset
clk: si5351: implement remove handler
* clk-pxa:
clk: pxa: unbreak lookup of CLK_POUT
* clk-qcom-alpha-pll:
clk: qcom: add read-only alpha pll post divider operations
clk: qcom: support for 2 bit PLL post divider
clk: qcom: support Brammo type Alpha PLL
clk: qcom: support Huayra type Alpha PLL
clk: qcom: support for dynamic updating the PLL
clk: qcom: support for alpha mode configuration
clk: qcom: flag for 64 bit CONFIG_CTL
clk: qcom: fix 16 bit alpha support calculation
clk: qcom: support for alpha pll properties
* clk-check-ops-ptr:
clk: check ops pointer on clock register
* clk-protect-rate:
clk: fix set_rate_range when current rate is out of range
clk: add clk_rate_exclusive api
clk: cosmetic changes to clk_summary debugfs entry
clk: add clock protection mechanism to clk core
clk: use round rate to bail out early in set_rate
clk: rework calls to round and determine rate callbacks
clk: add clk_core_set_phase_nolock function
clk: take the prepare lock out of clk_core_set_parent
clk: fix incorrect usage of ENOSYS
* clk-omap:
clk: ti: Drop legacy clk-3xxx-legacy code
The USB port 1 clock gate control has an inversed polarity
from all the other clock gates in the chip. This makes the
aspeed_clk_{enable,disable} functions honor the flag
CLK_GATE_SET_TO_DISABLE and set that flag appropriately
so it's set for all clocks except USB port 1.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In case of error, the function of_iomap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: a2e230c7b2ea ("clk: Add clock driver for ASPEED BMC SoCs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There are some resets that are not associated with gates. These are
represented by a reset controller.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The majority of the clocks in the system are gates paired with a reset
controller that holds the IP in reset.
This borrows from clk_hw_register_gate, but registers two 'gates', one
to control the clock enable register and the other to control the reset
IP. This allows us to enforce the ordering:
1. Place IP in reset
2. Enable clock
3. Delay
4. Release reset
There are some gates that do not have an associated reset; these are
handled by using -1 as the index for the reset.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This registers a platform driver to set up all of the non-core clocks.
The clocks that have configurable rates are now registered.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This registers the core clocks; those which are required to calculate
the rate of the timer peripheral so the system can load a clocksource
driver.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This adds the stub of a driver for the ASPEED SoCs. The clocks are
defined and the static registration is set up.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for the clocks provided by the CGU in the Ingenic JZ4770
SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18482/
Signed-off-by: James Hogan <jhogan@kernel.org>
This commit permits the PLLs to be dynamically enabled and disabled when
their children clocks are enabled and disabled.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18480/
Signed-off-by: James Hogan <jhogan@kernel.org>
The second PLL of the JZ4770 does not have a bypass bit.
This commit makes it possible to support it with the current common CGU
code.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18479/
Signed-off-by: James Hogan <jhogan@kernel.org>
Previously, the clocks with a fixed divider would report their rate
as being the same as the one of their parent, independently of the
divider in use. This commit fixes this behaviour.
This went unnoticed as neither the jz4740 nor the jz4780 CGU code
have clocks with fixed dividers yet.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18477/
Signed-off-by: James Hogan <jhogan@kernel.org>
The CGU common code does not modify the pointed clk_ops structure, so it
should be marked as const.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Maarten ter Huurne <maarten@treewalker.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18476/
Signed-off-by: James Hogan <jhogan@kernel.org>
Changes from v1->v2:
Add 'select RESET_CONTROLLER' under COMMON_CLK_MEDIATEK and enable
reset.c to be built when COMMON_CLK_MEDIATEK is selected. That should
be quite reasonable because the reset controller is tightly embedded
inside and exported from these clock subsystems. At least it can be found
on infracfg and pericfg subsystem that both are really fundamental block
lots of devices must depend on.
commit 74cb0d6dde ("clk: mediatek: fixup test-building of MediaTek clock
drivers") can let the build system looking into the directory where the
clock drivers resides and then allow test-building the drivers.
But the change also gives rise to certain incorrect behavior which is
reset.c being built even not depending on either COMPILE_TEST or
ARCH_MEDIATEK alternative dependency. To get rid of reset.c being built
unexpectedly on the other platforms, it would be a good change that the
file should be built depending on its own specific configuration rather
than just on generic RESET_CONTROLLER one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reentrant calls to clk_enable() are not working on UP systems. This is
caused by the fact spin_trylock_irqsave() always returns true when
CONFIG_SMP=n (and CONFIG_DEBUG_SPINLOCK=n) which causes the reference
counting to not work correctly when clk_enable_lock() is called twice
before clk_enable_unlock() is called (this happens when clk_enable()
is called from within another clk_enable()).
This fixes the problem by skipping the call to spin_trylock_irqsave() on UP
systems and relying solely on reference counting. We also make sure to set
flags in this case so that we are not returning an uninitialized value.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
platform_get_resource() may return NULL, add proper
check to avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, matching the data
types.
Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.
clk_core.rate and .accuracy are "unsigned long", hence casting
their addresses to "u32 *" exposed the wrong halves on big-endian
64-bit systems. Fix this by using debugfs_create_ulong() instead.
Octal permissions are preferred, as they are easier to read than
symbolic permissions. Hence replace "S_IRUGO" by "0444"
throughout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[sboyd@codeaurora.org: Squash the octal change in too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the virtual "clk_flags" file in debugfs shows the numeric
value of the top-level framework flags for the specified clock.
Hence the user must manually interpret these values.
Moreover, on big-endian 64-bit systems, the wrong half of the value is
shown, due to the cast from "unsigned long *" to "u32 *".
Fix both issues by showing the symbolic flag names instead.
Any non-standard flags are shown as a hex number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We can move these APIs into the private header file now that we
don't have any users of the __clk_get() and __clk_put() APIs
outside of clkdev.c and clk.c.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We'd like to privatize __clk_get(), but the sunxi clk driver is
calling this function to keep a reference held on the clk and
call clk_prepare_enable() on it. We support this design in the
clk core now with the CLK_IS_CRITICAL flag, so let's just use
that instead.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "flags" parameter passed to of_clk_detect_critical() cannot be a
pointer to a real clk_core.flags field, as clk_core is private to the
clock framework internals.
Change the comment to refer to top-level framework flags instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
TCON1 also has M divider, contrary to TCON0. And the mux is only
2 bits wide, instead of 3.
Fixes: 05359be117 ("clk: sunxi-ng: Add driver for A83T CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[wens@csie.org: Add description about mux width difference]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Now that all the users of asm/clkdev.h have been replaced with
the generic file we can get rid of the asm-generic file as well
and implement that code directly where it's used.
We only have one caller of __clkdev_alloc(), in clkdev.c so we
can easily remove that and drop the include of asm/clkdev.h in
linux/clkdev.h by putting the __clk_get/__clk_put inlines in
their respective location.
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a driver for the APCS clock controller. It is part of the APCS
hardware block, which among other things implements also a combined
mux and half integer divider functionality. It can choose between a
fixed-rate clock or the dedicated APCS (A53) PLL. The source and the
divider can be set both at the same time.
This is required for enabling CPU frequency scaling on MSM8916-based
platforms.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Include rcg header for parent_map, drop
multiple unneeded includes, add COMPILE_TEST to APCS depends,
made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for hardware that can switch both parent clock and divider
at the same time. This avoids generating intermediate frequencies from
either the old parent clock and new divider or new parent clock and
old divider combinations.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Change a comment style, drop parent_map in
favor of a u32 array instead, export symbols for clk_ops and mux
function]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CPUs on Qualcomm MSM8916-based platforms are clocked by two PLLs,
a primary (A53) CPU PLL and a secondary fixed-rate GPLL0. These sources
are connected to a mux and half-integer divider, which is feeding the
CPU cores.
This patch adds support for the primary CPU PLL which generates the
higher range of frequencies above 1GHz.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
[sboyd@codeaurora.org: Move to devm provider registration,
NUL terminate frequency table, made tristate/modular]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The clocks of A64/H5 SoCs in the DE2 CCU is the same as the clocks in H3
DE2 CCU rather than the A83T DE2 CCU (the parent of them is the DE
module clock).
Fix this by change the clock descriptions to use the clocks of H3.
Fixes: 763c5bd045 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner H3 features a DE2 CCU like the one on A83T, however the
parent of the clocks is the DE module clock, not the PLL_DE clock.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix ptr_ret.cocci warnings:
drivers/clk/mvebu/armada-37xx-periph.c:362:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
There were a few fields in the iproc pll data structures that were
holding information that was not true state information.
Using stack variables is sufficient and simplifies the structure.
There are not any functional changes in this commit.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The iproc plls are capable of doing small rate changes without the
need for a full reset and re-lock procedure. This feature will
allow for small tweaks to the PLL rate to occur smoothly.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The pll post divider code was using DIV_ROUND_UP when determining the
divider value best suited to produce the target frequency.
Using DIV_ROUND_CLOSEST will give us better divider values when
the division results in a small remainder.
Also, change the post divider clock over to the determine_rate api
instead of round_rate.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the ability for the iproc pll to calculate the pll parameters at
runtime instead of only using predefined tables. This ability allows
the clock users to select from the full range of vco frequencies.
The old method of table based programming is retained so that existing
users will retain expected behavior. The flag IPROC_CLK_PLL_CALC_PARAM
will need to be set to enable the new runtime calculation method.
Currently, this is only being enabled for the audio pll.
This feature also revealed a problem with the driver using the
round_rate api. The round_rate api does not allow for frequencies larger
than 2^31 to be returned. Those large frequencies are interpreted as an
error code. Therefore, we are moving to the determine_rate api which
solves this problem.
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since switching to clk drivers, the CLK_POUT cannot be searched for by
clk_get() API and thus it returns with ENOENT.
Register it with the clk_lookup and thus unbreak the users of it.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fixes the following sparse warning:
drivers/clk/meson/axg.c:260:25: warning:
symbol 'axg_gp0_params_table' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Current clk_pm_runtime_put is using pm_runtime_put_sync which
is not safe to be called in clk_core_is_enabled as it should
be able to run in atomic context.
Thus use pm_runtime_put instead which is atomic safe.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 9a34b45397 ("clk: Add support for runtime PM")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Even though the header file linux/clk-provider.h is already being properly
included in clk-mtk.h, the definition of struct clk_onecell_data still
must depend on CONFIG_COMMON_CLK defined and thus it's possible that
below build warnings occur when CONFIG_COMMON_CLK is not being selected.
Therefore, these functions which need struct clk_onecell_data without
declaring that structure first requires simply declaring that this struct
exists prior to referencing it in clk-mtk.h
Changes from v1->v2:
enhance v1 based on two useful solutions Jean Delvare kindly suggested.
All warnings (new ones prefixed by >>):
In file included from drivers/clk/mediatek/reset.c:22:0:
>>drivers/clk/mediatek/clk-mtk.h:44:19: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
int num, struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:63:19: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
int num, struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:145:10: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:164:11: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of
this definition or declaration
struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
drivers/clk/mediatek/clk-mtk.h:190:12: warning: 'struct clk_onecell_data'
declared inside parameter list will not be visible outside of this
definition or declaration
struct clk_onecell_data *clk_data);
^~~~~~~~~~~~~~~~
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: kbuild-all@01.org
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Jean Delvare <jdelvare@suse.de>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
"rem * SDM_DEN" can easily overflow on the 32-bit Meson8 and Meson8b
SoCs if the "remainder" (after the division operation) is greater than
262143Hz. This is likely to happen since the input clock for the MPLLs
on Meson8 and Meson8b is "fixed_pll", which is running at a rate of
2550MHz.
One example where this was observed to be problematic was the Ethernet
clock calculation (which takes MPLL2 as input). When requesting a rate
of 125MHz there is a remainder of 2500000Hz.
The resulting MPLL2 rate before this patch was 127488329Hz.
The resulting MPLL2 rate after this patch is 124999103Hz.
Commit b609338b26 ("clk: meson: mpll: use 64bit math in
rate_from_params") already fixed a similar issue in rate_from_params.
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The si5351 driver should not prepare or enable other clocks in the tree on
probe. Let the clients decide when to prepare or enable the clocks.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
[sboyd@codeaurora.org: Remove most of the .remove function too]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This drivers probe fails due to a clock name collision if a clock named
'plla' or 'pllb' is already registered when registering this drivers
internal plls.
Fix it by renaming internal plls to avoid name collisions.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The "Si5351A/B/C Data Sheet" states to apply a PLL soft reset before
enabling the output clocks [1]. This is required to get a deterministic
phase relationship between the output clocks.
Without resetting the PLL, the phase relationship between the clocks is
unpredictable. Fix this by resetting the PLL in si5351_clkout_prepare().
References:
[1] https://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351-B.pdf
Figure 12 ("I2C Programming Procedure")
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add optional output clock DT property to enable PLL reset when a clock
output is enabled.
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Sergej Sawazki <sergej@taudac.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The driver has no remove function, so it does not cleanup
resources that are not under devm management.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
To minimize the rounding error round to the closest integer when
calculating the result in the recalc_rate() and set_rate() callbacks.
Also in order to improve precision multiply first and then divide.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If the nocount bit is set the divider is bypassed and the settings for the
divider count should be ignored and a divider value of 1 should be assumed.
Handle this correctly in the driver recalc_rate() callback.
While the driver sets up the part so that the read back dividers values
yield the correct result the power-on reset settings of the part might not
reflect this and hence calling e.g. clk_get_rate() without prior calls to
clk_set_rate() will yield the wrong result.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The orphan clocks reparent operation shouldn't touch the hardware
if clocks are enabled, otherwise it may get a chance to disable a
newly registered critical clock which triggers the warning below.
Assuming we have two clocks: A and B, B is the parent of A.
Clock A has flag: CLK_OPS_PARENT_ENABLE
Clock B has flag: CLK_IS_CRITICAL
Step 1:
Clock A is registered, then it becomes orphan.
Step 2:
Clock B is registered. Before clock B reach the critical clock enable
operation, orphan A will find the newly registered parent B and do
reparent operation, then parent B will be finally disabled in
__clk_set_parent_after() due to CLK_OPS_PARENT_ENABLE flag as there's
still no users of B which will then trigger the following warning.
WARNING: CPU: 0 PID: 0 at drivers/clk/clk.c:597 clk_core_disable+0xb4/0xe0
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.11.0-rc1-00056-gdff1f66-dirty #1373
Hardware name: Generic DT based system
Backtrace:
[<c010c4bc>] (dump_backtrace) from [<c010c764>] (show_stack+0x18/0x1c)
r6:600000d3 r5:00000000 r4:c0e26358 r3:00000000
[<c010c74c>] (show_stack) from [<c040599c>] (dump_stack+0xb4/0xe8)
[<c04058e8>] (dump_stack) from [<c0125c94>] (__warn+0xd8/0x104)
r10:c0c21cd0 r9:c048aa78 r8:00000255 r7:00000009 r6:c0c1cd90 r5:00000000
r4:00000000 r3:c0e01d34
[<c0125bbc>] (__warn) from [<c0125d74>] (warn_slowpath_null+0x28/0x30)
r9:00000000 r8:ef00bf80 r7:c165ac4c r6:ef00bf80 r5:ef00bf80 r4:ef00bf80
[<c0125d4c>] (warn_slowpath_null) from [<c048aa78>] (clk_core_disable+0xb4/0xe0)
[<c048a9c4>] (clk_core_disable) from [<c048be88>] (clk_core_disable_lock+0x20/0x2c)
r4:000000d3 r3:c0e0af00
[<c048be68>] (clk_core_disable_lock) from [<c048c224>] (clk_core_disable_unprepare+0x14/0x28)
r5:00000000 r4:ef00bf80
[<c048c210>] (clk_core_disable_unprepare) from [<c048c270>] (__clk_set_parent_after+0x38/0x54)
r4:ef00bd80 r3:000010a0
[<c048c238>] (__clk_set_parent_after) from [<c048daa8>] (clk_register+0x4d0/0x648)
r6:ef00d500 r5:ef00bf80 r4:ef00bd80 r3:ef00bfd4
[<c048d5d8>] (clk_register) from [<c048dc30>] (clk_hw_register+0x10/0x1c)
r9:00000000 r8:00000003 r7:00000000 r6:00000824 r5:00000001 r4:ef00d500
[<c048dc20>] (clk_hw_register) from [<c048e698>] (_register_divider+0xcc/0x120)
[<c048e5cc>] (_register_divider) from [<c048e730>] (clk_register_divider+0x44/0x54)
r10:00000004 r9:00000003 r8:00000001 r7:00000000 r6:00000003 r5:00000001
r4:f0810030
[<c048e6ec>] (clk_register_divider) from [<c0d3ff58>] (imx7ulp_clocks_init+0x558/0xe98)
r7:c0e296f8 r6:c165c808 r5:00000000 r4:c165c808
[<c0d3fa00>] (imx7ulp_clocks_init) from [<c0d24db0>] (of_clk_init+0x118/0x1e0)
r10:00000001 r9:c0e01f68 r8:00000000 r7:c0e01f60 r6:ef7f8974 r5:ef0035c0
r4:00000006
[<c0d24c98>] (of_clk_init) from [<c0d04a50>] (time_init+0x2c/0x38)
r10:efffed40 r9:c0d61a48 r8:c0e78000 r7:c0e07900 r6:ffffffff r5:c0e78000
r4:00000000
[<c0d04a24>] (time_init) from [<c0d00b8c>] (start_kernel+0x218/0x394)
[<c0d00974>] (start_kernel) from [<6000807c>] (0x6000807c)
r10:00000000 r9:410fc075 r8:6000406a r7:c0e0c930 r6:c0d61a44 r5:c0e07918
r4:c0e78294
We know that the clk isn't enabled with any sort of prepare_count
here so we don't need to enable anything to prevent a race. And
we're holding the prepare mutex so set_rate/set_parent can't race
here either. Based on an earlier patch by Dong Aisheng.
Fixes: fc8726a2c0 ("clk: core: support clocks which requires parents enable (part 2)")
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Let the build system looking into the directiory where the clock drivers
resides for the COMPILE_TEST alternative dependency allows test-building
the drivers.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Getting much MediaTek clock driver have been added to CCF, so it's
better adding the cleanup for grouping drivers under the independent
menu to simplify configuration selection. In addition, really trivial
fixups for typos are added in the same patch.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When an AT91 programmable clock is declared in the device tree, register
it into the Power Management Controller driver. On entering suspend mode,
the driver saves and restores the Programmable Clock registers to support
the backup mode for these clocks.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The contents of the System Clock Status Register (SCSR) needs to be
restored into the System Clock Enable Register (SCER).
As the bootloader will restore some clocks by itself, the issue can be
missed as only the USB controller, the LCD controller, the Image Sensor
controller and the programmable clocks will be impacted.
Fix the obvious typo in the suspend/resume code, as the IMR register
does not need to be saved twice.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Wait for the syncronization of all clocks when resuming, not only the
UPLL clock. Do not use regmap_read_poll_timeout, as it will call BUG()
when interrupts are masked, which is the case in here.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PCIE and NSS has MISC reset register in which single register has
multiple reset bit. The patch adds these resets with its
corresponding reset bits.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- It has 3 general purpose clock controller which supplies
the clock in GPIO pins.
- It has Crypto Engine which has AXI, AHB and Core clocks.
Other non APSS processors can also use Crypto Engine so
these clocks are marked as VOTED clocks.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IPQ8074 has 6 ethernet ports which supports all ethernet speeds
from 10Mpbs to 10 Gpbs and each speed requires different clock
rates. Each port has separate TX and RX clocks. These clocks
use separate external UNIPHY PLL’s which will be registered with
separate NSS driver. The clock frequency is 125 Mhz for UNIPHY0
and 312.5 Mhz for UNIPHY1 and UNIPHY2.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
IPQ8074 has NSS (Network Switching System) which has 2 UBI cores
and hardware crypto engine. Some clocks are separate for each UBI
core and remaining NSS clocks are common. The BIAS_PLL (300 Mhz)
and BIAS_PLL_NSS_NOC (416.5 Mhz) are external fixed clocks and
will be registered from dtsi or NSS driver.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- It has 2 instances of PCIE which uses AXI, AHB, AUX, SYS NOC
AXI and PIPE clocks.
- It has 2 instances of USB 3.0 which uses AUX, SLEEP, PIPE,
SYS NOC, mock UTMI and master clocks.
- It has 2 instances of SDCC which uses APSS and AHB clock.
SDCC1 requires ICE core clock also.
- All the PIPE clocks are external clocks which will be
registered in clock framework by PHY drivers. The enabling
and disabling of PIPE RCG clocks are dependent upon PHY
initialization sequence so BRANCH_HALT_DELAY flag is required for
these clocks.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- GPLL2, GPLL4 and GPLL6 are general PLL clocks and parent
for all core peripherals.
- UBI PLL is mainly used by NSS (Network Switching System).
IPQ8074 has 2 instances of NSS UBI cores and UBI PLL will
be used to control the core frequency.
- NSS Crypto PLL is mainly used by NSS Crypto Engine which
supports the multiple cryptographic algorithm used in
Ethernet.
- IPQ8074 frequency plan does not require change in PLL post
dividers so marked the same as read-only.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
GPLL0 uses 4 bits post divider which should be specified
in clock driver structure.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the driver assumes the register configuration value
is identical to its index in the parent map. This patch adds
the parent map field in regmap mux clock node which contains
the mapping of parent index with actual register configuration
value. If regmap node contains this parent map then the
configuration value will be taken from this
parent map instead of simply writing the index value.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM dividers
which is equivalent to generic divider operations in
'commit 79c6ab5095 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
i.MX51 only has 3 UARTs and no CCGR7 register. In place of the CCGR7
register on i.MX50/i.MX53 that contains the ipg and per clock gates
for UARTs 4 and 5, on i.MX51 there is the CMEOR register.
Without this patch, the code disabling the UART clocks would also clear
the mod_en_ov_vpu bit in the CMEOR register, among others, which causes
register accesses to the VPU to lock up the system.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
More divider clocks are needed by IP. So enlarge the PLL divider
array to accommodate more divider clocks.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When DVFS is enabled the CPU clock setting is done using an other set of
registers.
These Power Management registers are exposed through a syscon as they
will also be used by other drivers such as the cpufreq.
This patch add the possibility to modify the CPU frequency using the
associate load level matching the target frequency. Then all the
frequency switch is handle by the hardware.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
[sboyd@codeaurora.org: Grow a local variable for regmap pointer
to keep lines shorter]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When DVFS will be enabled then the cpu clk will use a different set of
register at run time. That means that we won't be able to use the common
callback and need to use our own ones.
This patch prepares this change by switching on our own set of callbacks
without modifying the behavior of the clocks.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patches fixes few cosmetic issues such as alignment, blank lines
and required space.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch added the list of clocks for Spreadtrum's SC9860 SoC,
together with clock initialization code.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Introduced a common adjustable pll clock driver for Spreadtrum SoCs.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch introduced composite driver for Spreadtrum's SoCs. The
functions of this composite clock simply consist of divider and
mux clocks.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is a feature that can also be found in sprd composite clocks,
provide a bunch of helpers that can be reused later on.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds clock multiplexor support for Spreadtrum platforms,
the mux clocks also can be found in sprd composite clocks, so
provides two helpers that can be reused later on.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some clocks on the Spreadtrum's SoCs are just simple gates. Add
support for those clocks.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Added Spreadtrum's clock driver framework together with common
structures and interface functions.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These macros are used by more than one SoC vendor platforms, avoid to
have many copies of these code, this patch moves them to the common
header file which every clock drivers can access to.
Signed-off-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Calling clk_core_set_rate() with core->req_rate is basically a no-op
because of the early bail-out mechanism.
This may leave the clock in inconsistent state if the rate is out the
requested range. Calling clk_core_set_rate() with the closest rate
limit could solve the problem but:
- The underlying determine_rate() callback needs to account for this
corner case (rounding within the range, if possible)
- if only round_rate() is available, we rely on luck unfortunately.
Fixes: 1c8e600440 ("clk: Add rate constraints to clocks")
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-11-jbrunet@baylibre.com
Using clock rate protection, we can now provide a way for clock consumer
to claim exclusive control over the rate of a producer
So far, rate change operations have been a "last write wins" affair. This
changes allows drivers to explicitly protect against this behavior, if
required.
Of course, if exclusivity over a producer is claimed more than once, the
rate is effectively locked as exclusivity cannot be preempted
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-10-jbrunet@baylibre.com
The patch adds clk_core_protect and clk_core_unprotect to the internal
CCF API. These functions allow to set a new constraint along the clock
tree to prevent any change, even indirect, which may result in rate
change or glitch.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-7-jbrunet@baylibre.com
The current implementation of clk_core_set_rate_nolock() bails out early
if the requested rate is exactly the same as the one set. It should bail
out if the request would not result in a rate a change. This is important
when the rate is not exactly what is requested, which is fairly common
with PLLs.
Ex: provider able to give any rate with steps of 100Hz
- 1st consumer request 48000Hz and gets it.
- 2nd consumer request 48010Hz as well. If we were to perform the usual
mechanism, we would get 48000Hz as well. The clock would not change so
there is no point performing any checks to make sure the clock can
change, we know it won't.
This is important to prepare the addition of the clock protection
mechanism
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-6-jbrunet@baylibre.com
Rework the way the callbacks round_rate() and determine_rate() are called.
The goal is to do this at a single point and make it easier to add
conditions before calling them.
Because of this factorization, rate returned by determine_rate() is also
checked against the min and max rate values
This rework is done to ease the integration of "protected" clock
functionality.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-5-jbrunet@baylibre.com
Create a core function for set_phase, as it is done for set_rate and
set_parent.
This rework is done to ease the integration of "protected" clock
functionality.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-4-jbrunet@baylibre.com
Rework set_parent core function so it can be called when the prepare lock
is already held by the caller.
This rework is done to ease the integration of the "protected" clock
functionality.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-3-jbrunet@baylibre.com
ENOSYS is special and should only be used for incorrect syscall number.
It does not seem to be the case here.
Reported by checkpatch.pl while working on clock protection.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171201215200.23523-2-jbrunet@baylibre.com
Our MMC host driver now issues a reset, instead of just deasserting
the reset control, since commit c34eda69ad ("mmc: sunxi: Reset the
device at probe time"). The sun9i-mmc clock driver does not support
this, and will fail, which results in MMC not probing.
This patch implements the reset callback by asserting the reset control,
then deasserting it after a small delay.
Fixes: 7a6fca879f ("clk: sunxi: Add driver for A80 MMC config clocks/resets")
Cc: <stable@vger.kernel.org> # 4.14.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171218035751.20661-1-wens@csie.org
Nothing really prevents a provider from (trying to) register a clock
without providing the clock ops structure.
We do check the individual fields before using them, but not the
structure pointer itself. This may have the usual nasty consequences when
the pointer is dereferenced, most likely when checking one the field
during the initialization.
This is fixed by returning an error on clock register if the ops pointer
is NULL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20171219083329.24746-1-jbrunet@baylibre.com
We have now had omap3 booting in device tree only mode for a while
and all this code is unused.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If a device is part of the CPG/MSSR Clock Domain and to be used as a
wakeup source, it must be kept active during system suspend.
Currently this is handled in device-specific drivers by explicitly
increasing the use count of the module clock when the device is
configured as a wakeup source. However, the proper way to prevent the
device from being stopped is to inform this requirement to the genpd
core, by setting the GENPD_FLAG_ACTIVE_WAKEUP flag.
Note that this will only affect devices configured as wakeup sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
