When a USB device is connected to the USB host port on the SAM9N12 then
you get "-62" error which seems to indicate USB replies from the device
are timing out. Based on a logic sniffer, I saw the USB bus was running
at half speed.
The PLL code uses cached MUL and DIV values which get set in set_rate()
and applied in prepare(), but the recalc_rate() function instead
queries the hardware instead of using these cached values. Therefore,
if recalc_rate() is called between a set_rate() and prepare(), the
wrong frequency is calculated and later the USB clock divider for the
SAM9N12 SOC will be configured for an incorrect clock.
In my case, the PLL hardware was set to 96 Mhz before the OHCI
driver loads, and therefore the usb clock divider was being set
to /2 even though the OHCI driver set the PLL to 48 Mhz.
As an alternative explanation, I noticed this was fixed in the past by
87e2ed338f ("clk: at91: fix recalc_rate implementation of PLL
driver") but the bug was later re-introduced by 1bdf02326b ("clk:
at91: make use of syscon/regmap internally").
Fixes: 1bdf02326b ("clk: at91: make use of syscon/regmap internally)
Cc: <stable@vger.kernel.org>
Signed-off-by: Marcin Ziemianowicz <marcin@ziemianowicz.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
for the TI Davinci family of SoCs. So far those clks have been supported
with a custom implementation of the clk API in the arch port instead of in
the CCF. With this driver merged we're one step closer to having a single
clk API implementation.
The other large diff is from the Amlogic clk driver that underwent some
major surgery to use regmap. Beyond that, the biggest hitter is Samsung
which needed some reworks to properly handle clk provider power domains
and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some cleanups
and small fixes for some of the more esoteric features. And the usual
set of driver non-critical fixes, cleanups, and minor additions are here as
well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAlrPhMARHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSVkkxAArsItSoxQV18kQlJ9S7o2z75giquXQfvy
Y/cKIIY1kz4K+qm+rpbl6PjukrSPtfM+wGmepGt+CptOdlj672viFxI7zjrd1iSy
/xJo7d5/nZxvmx0qcwYWVTCOsU+4FUUkpq5mE91KEvwny/qgRqEgWeLoWTDLBktF
MzGtBUYudjkRYLd2I31DGB3dqI0Dy9JwuEpJfCAt5h4dztml3aNjYknjQ/vUSEXL
61mSYM1fwzK8rnrjSlQqb+X0OoJ6d5Pz2uHRXnWfGlS8UOh5N9NFGKpiErLm+h/+
/FigA6f9HBeUneNf5Dnu568FHwE2FyUbZKVd40OYj3x128OnAoKUoRt68/8FQPdf
NoQb3zH3Ha1JbwWgvQ9RkWp82kYnMctrlkh6IFye/FxdfwCWA4SE/iIgJXRJbQ/K
blZz14jkXT8oISqy6nryGv3CK/RFXzVdvVa4z41xHc4cnLpNBsv1o89a+9MyTvMD
wYOnc/98/l5xYs5PvQqNrd/onE0GLIeOEtkWNXH0OACe6FOIuz5eVn4Uh8aIm0wl
+EHwHRwB7AQK+a7jwEfQ88aceAntvFlymUUcsncyCXn2s0knc5BHJPSHhoZk1tJb
Wv2Fcln3Mwjhhq9aoNxfAJf4pIqmFgdQEtwyND4GJlP55Xay5QMZVEdwnNfFDvmf
X6P2pfkBqkg=
=ys4O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The large diff this time around is from the addition of a new clk
driver for the TI Davinci family of SoCs. So far those clks have been
supported with a custom implementation of the clk API in the arch port
instead of in the CCF. With this driver merged we're one step closer
to having a single clk API implementation.
The other large diff is from the Amlogic clk driver that underwent
some major surgery to use regmap. Beyond that, the biggest hitter is
Samsung which needed some reworks to properly handle clk provider
power domains and a bunch of PLL rate updates.
The core framework was fairly quiet this round, just getting some
cleanups and small fixes for some of the more esoteric features. And
the usual set of driver non-critical fixes, cleanups, and minor
additions are here as well.
Core:
- Rejig clk_ops::init() to be a little earlier for phase/accuracy ops
- debugfs ops macroized to shave some lines of boilerplate code
- Always calculate the phase instead of caching it in clk_get_phase()
- More __must_check on bulk clk APIs
New Drivers:
- TI's Davinci family of SoCs
- Intel's Stratix10 SoC
- stm32mp157 SoC
- Allwinner H6 CCU
- Silicon Labs SI544 clock generator chip
- Renesas R-Car M3-N and V3H SoCs
- i.MX6SLL SoCs
Removed Drivers:
- ST-Ericsson AB8540/9540
Updates:
- Mediatek MT2701 and MT7622 audsys support and MT2712 updates
- STM32F469 DSI and STM32F769 sdmmc2 support
- GPIO clks can sleep now
- Spreadtrum SC9860 RTC clks
- Nvidia Tegra MBIST workarounds and various minor fixes
- Rockchip phase handling fixes and a memory leak plugged
- Renesas drivers switch to readl/writel from clk_readl/clk_writel
- Renesas gained CPU (Z/Z2) and watchdog support
- Rockchip rk3328 display clks and rk3399 1.6GHz PLL support
- Qualcomm PM8921 PMIC XO buffers
- Amlogic migrates to regmap APIs
- TI Keystone clk latching support
- Allwinner H3 and H5 video clk fixes
- Broadcom BCM2835 PLLs needed another bit to enable
- i.MX6SX CKO mux fix and i.MX7D Video PLL divider fix
- i.MX6UL/ULL epdc_podf support
- Hi3798CV200 COMBPHY0 and USB2_OTG_UTMI and phase support for eMMC"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (233 commits)
clk: davinci: add a reset lookup table for psc0
clk: imx: add clock driver for imx6sll
dt-bindings: imx: update clock doc for imx6sll
clk: imx: add new gate/gate2 wrapper funtion
clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux
clk: cs2000: set pm_ops in hibernate-compatible way
clk: bcm2835: De-assert/assert PLL reset signal when appropriate
clk: imx7d: Move clks_init_on before any clock operations
clk: imx7d: Correct ahb clk parent select
clk: imx7d: Correct dram pll type
clk: imx7d: Add USB clock information
clk: socfpga: stratix10: add clock driver for Stratix10 platform
dt-bindings: documentation: add clock bindings information for Stratix10
clk: ti: fix flag space conflict with clkctrl clocks
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: Add driver for the si544 clock generator chip
clk: davinci: Remove redundant dev_err calls
clk: uniphier: add ethernet clock control support for PXs3
...
* clk-davinci:
clk: davinci: add a reset lookup table for psc0
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
In order to be able to use the reset framework in legacy boot mode as
well, add the reset lookup table to the psc driver for da850 variant.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-davinci:
clk: davinci: Remove redundant dev_err calls
clk: davinci: cfgchip: Add TI DA8XX USB PHY clocks
clk: davinci: New driver for TI DA8XX CFGCHIP clocks
dt-bindings: clock: Add bindings for DA8XX CFGCHIP clocks
clk: davinci: Add platform information for TI DM646x PSC
clk: davinci: Add platform information for TI DM644x PSC
clk: davinci: Add platform information for TI DM365 PSC
clk: davinci: Add platform information for TI DM355 PSC
clk: davinci: Add platform information for TI DA850 PSC
clk: davinci: Add platform information for TI DA830 PSC
clk: davinci: New driver for davinci PSC clocks
dt-bindings: clock: New bindings for TI Davinci PSC
clk: davinci: Add platform information for TI DM646x PLL
clk: davinci: Add platform information for TI DM644x PLL
clk: davinci: Add platform information for TI DM365 PLL
clk: davinci: Add platform information for TI DM355 PLL
clk: davinci: Add platform information for TI DA850 PLL
clk: davinci: Add platform information for TI DA830 PLL
clk: davinci: New driver for davinci PLL clocks
dt-bindings: clock: Add new bindings for TI Davinci PLL clocks
* clk-si544:
clk: Add driver for the si544 clock generator chip
* clk-rockchip:
clk: rockchip: assign correct id for pclk_ddr and hclk_sd in rk3399
clk: rockchip: Fix error return in phase clock registration
clk: rockchip: Correct the behaviour of restoring cached phase
clk: rockchip: Fix wrong parents for MMC phase clock for rk3328
clk: rockchip: Fix wrong parent for SDMMC phase clock for rk3228
clk: rockchip: Add 1.6GHz PLL rate for rk3399
clk: rockchip: Restore the clock phase after the rate was changed
clk: rockchip: Prevent calculating mmc phase if clock rate is zero
clk: rockchip: Free the memory on the error path
clk: rockchip: document hdmi_phy external input for rk3328
clk: rockchip: add flags for rk3328 dclk_lcdc
clk: rockchip: remove ignore_unused flag from rk3328 vio_h2p clocks
clk: rockchip: protect all remaining rk3328 interconnect clocks
clk: rockchip: export sclk_hdmi_sfc on rk3328
clk: rockchip: remove HCLK_VIO from rk3328 dt header
clk: rockchip: fix hclk_vio_niu on rk3328
* clk-uniphier:
clk: uniphier: add additional ethernet clock lines for Pro4
clk: uniphier: add SATA clock control support
clk: uniphier: add PCIe clock control support
clk: uniphier: add ethernet clock control support for PXs3
clk: uniphier: add Pro4/Pro5/PXs2 audio system clock
* clk-ti-flag-fix:
clk: ti: fix flag space conflict with clkctrl clocks
clk: ti: clkctrl: add support for CLK_SET_RATE_PARENT flag
* clk-mvebu:
clk: mvebu: armada-38x: add support for missing clocks
clk: mvebu: cp110: Fix clock tree representation
* clk-phase:
clk: Don't show the incorrect clock phase
clk: update cached phase to respect the fact when setting phase
* clk-nxp:
clk: lpc32xx: Set name of regmap_config
* clk-mtk2712:
clk: mediatek: update clock driver of MT2712
dt-bindings: clock: add clocks for MT2712
* clk-qcom-rpmcc:
clk: qcom: rpmcc: Add support to XO buffered clocks
Add clk driver support for imx6sll.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new gate/gate2 wrapper function to register clocks with optional flags.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The busy divider and busy mux is actually used by the system critical clocks,
so add 'CLK_IS_CRITICAL' to clocks registered with these two type.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use SET_LATE_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.resume_early field.
This fixes initialization of CS2000 in restore from hibernation in case
of kernel used to load image did not initialize CS2000 while kernel
being restored had CS2000 initialized.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
In order to enable a PLL, not only the PLL has to be powered up and
locked, but you also have to de-assert the reset signal. The last part
was missing. Add it so PLLs that were not enabled by the FW/bootloader
can be enabled from Linux.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
For init on clocks we should move it at the first place in imx7d_clocks_init()
before any clock operations, else the clock operation may fail in case the clock
is still not on.
Acked-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Design team change the ahb's clk parent options but
did NOT update the DOC accordingly in time, so the
AHB/IPG's clk rate in clk tree is incorrect, AHB is
67.5MHz and IPG is 33.75MHz, but using scope to
monitor them, they are actually 135MHz and 67.5MHz,
update the clk parent option to make clk tree info
correct.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
DRAM PLL is a audio/video type PLL, need to correct
it to get correct ops of PLL.
There is a test_div placed before DRAM PLL's gate, so
add this test div clk.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add USB clock information, the pll_usb_main_clk is USB_PLL at CCM
which is the output of USBOTG2 PHY.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Irina Tirdea <irina.tirdea@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock driver for the Stratix10 SoC. The driver is similar to the
Cyclone5/Arria10 platforms, with the exception that this driver only uses
one single clock binding.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do power
management in a platform independent way. This has been through many
review cycles, and it relies on a rather interesting way of using the
mailbox subsystem, but in the end I agreed that Sudeep's version was
the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up
a little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pmsx
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes and
the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we get
two new machines based on its older siblings: the H5 based OrangePi
Zero+ and the A64 based Teres-I Laptop from Olimex. On the 32-bit side,
we add The Olimex som204 based on Allwinner A20, and the Banana Pi M2
Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6
family of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones Qualcomm
msm8974 based Galaxy S5 is a rather different phone made by the same
company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre Computer
Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on Rockchips
RK3368 and made by Theobroma Systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7rHo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is the usual set of changes for device trees, with over 700
non-merged changesets. There is an ongoing set of dtc warning fixes
and the usual bugfixes, cleanups and added device support.
The most interesting bit as usual is support for new machines listed
below:
- The Allwinner H6 makes its debut with the Pine-H64 board, and we
get two new machines based on its older siblings: the H5 based
OrangePi Zero+ and the A64 based Teres-I Laptop from Olimex. On the
32-bit side, we add The Olimex som204 based on Allwinner A20, and
the Banana Pi M2 Zero development board (based on H2).
- NVIDIA adds support for Tegra194 aka "Xavier", plus their p2972
development board and p2888 CPU module.
- The Nuvoton npcm750 is a BMC that was newly added, for now we only
support running on the evaluation board.
- STmicroelectronics stm32 gains support for the stm32mp157c and two
evaluation boards.
- The Toradex Colibri board family grows a few members based on the
i.MX6ULL variant.
- The Advantec DMS-BA16 is a Qseven module using the NXP i.MX6 family
of chips.
- The Phytec phyBOARD Mira is a family of industrial boards based on
i.MX6. For now, four models get added.
- TI am335x based PDU-001 is an industrial embedded machine used for
traffic monitoring
- The Aspeed platform now supports running on the BMC on the Qualcomm
Centriq 2400 server
- Samsung Exynos4 based Galaxy S3 is a family of mobile phones
Qualcomm msm8974 based Galaxy S5 is a rather different phone made
by the same company.
- The Xilinx Zynq and ZynqMP platforms now gained a lot of dts file
for the various boards made by Xilinx themselves, as well as the
Digilent Zybo Z7.
- The ARM Versatile family now supports the "IB2" interface board.
- The Renesas H2 based "Stout" and the H3 based Salvator-X are more
evaluation boards named after a kind of beer, as most of them are.
The r8a77980 (V3H) based "Condor" apparently doesn't follow that
tradition. ;-)
- ROC-RK3328-CC is a simple developement board from the Libre
Computer Project, based on the Rockchips RK3328 SoC
- Haiku is another development board plus Qseven module based on
Rockchips RK3368 and made by Theobroma Systems"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (701 commits)
arm: dts: modify Nuvoton NPCM7xx device tree structure
arm: dts: modify Makefile NPCM750 configuration name
arm: dts: modify clock binding in NPCM750 device tree
arm: dts: modify timer register size in NPCM750 device tree
arm: dts: modify UART compatible name in NPCM750 device tree
arm: dts: add watchdog device to NPCM750 device tree
arm64: dts: uniphier: add ethernet node for PXs3
ARM: dts: uniphier: add pinctrl groups of ethernet for second instance
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for board using GPL-2.0+
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0+/MIT
arm: dts: kirkwood*.dts: use SPDX-License-Identifier for boards using GPL-2.0
arm: dts: armada-385-turris-omnia: use SPDX-License-Identifier
arm: dts: armada-385-db-ap: use SPDX-License-Identifier
arm: dts: armada-388-rd: use SPDX-License-Identifier
arm: dts: armada-xp-db-xc3-24g4xg: use SPDX-License-Identifier
arm: dts: armada-xp-db-dxbc2: use SPDX-License-Identifier
arm: dts: armada-370-db: use SPDX-License-Identifier
arm: dts: armada-*.dts: use SPDX-License-Identifier for most of the Armada based board
arm: dts: armada-xp-98dx: use SPDX-License-Identifier for prestara 98d SoCs
arm: dts: armada-*.dtsi: use SPDX-License-Identifier for most of the Armada SoCs
...
The introduction of support for CLK_SET_RATE_PARENT flag for clkctrl
clocks used a generic clock flag, which causes a conflict with the
rest of the clkctrl flags, namely the NO_IDLEST flag. This can cause
boot failures on certain platforms where this flag is introduced, by
omitting the wait for the clockctrl module to be fully enabled before
proceeding with rest of the code.
Fix this by moving all the clkctrl specific flags to their own bit-range.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fixes: 49159a9dc3 ("clk: ti: add support for CLK_SET_RATE_PARENT flag")
Reported-by: Christophe Lyon <christophe.lyon@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pro4 SoC has clock lines for Giga-bit feature and ethernet phy,
and these are mandatory to activate the ethernet controller. This adds
support for the clock lines.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clock control for SATA controller on UniPhier SoCs. This adds
support for PXs2, LD20 and PXs3.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add clock control for PCIe controller on UniPhier SoCs. This adds
support for Pro5, LD20 and PXs3.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch adds the driver and devicetree documentation for the
Silicon Labs SI544 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 200kHz
to 1500MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd: assign max_freq to 0 in is_valid_frequency() to squelch warning]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Since hclk_sd and pclk_ddr source clock from CPLL or GPLL,
and these two PLL may change their frequency. If we do not
assign right id to pclk_ddr and hclk_sd, they will alway use
default cur register value, and may get the frequency
exceed their signed off frequency. So assign correct Id
for them, then we can assign frequency for them in dts.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The newly added clock notifier may return an error code but so far the
error output in the function would only return an error pointer from
registering the clock.
So when the clock notifier fails the clock would be unregistered but the
return would still be the clock pointer which could then not be
dereferenced correctly. So fix the error handling to prevent that.
Fixes: 60cf09e45f ("clk: rockchip: Restore the clock phase after the rate was changed")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We can't restore every phase, for instance the invalid phase and
the phase for coming rate which is out of the scope of boards'
ability. And this patch also corrects the error path to return
invalid pointer to clk if clk_notifier_register failed introduced
by the same offending commit.
Fixes: 60cf09e45f ("clk: rockchip: Restore the clock phase after the rate was changed")
Reported-by: wlq <wlq@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: wlq <wlq@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase if
clock rate is zero") catches some gremlins for clk-rk3328.c that the
parents of MMC phase clock should be clk_{sdmmc, sdio, emmc}, but not
sclk_{sdmmc, sdio, emmc}.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
commit c420c1e4db22 ("clk: rockchip: Prevent calculating mmc phase
if clock rate is zero") catches one gremlin again for clk-rk3228.c
that the parent of SDMMC phase clock should be sclk_sdmmc0, but not
sclk_sdmmc. However, the naming of the sdmmc clocks varies in the
manual with the card clock having the 0 while the hclk is named
without appended 0. So standardize one one format to prevent
confusion, as there also is only one (non-sdio) mmc controller on
the soc.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adjust the R8A77980-specific #ifdefs to use CLK instead of ARCH
to follow same style as other SoCs.
Fixes: ce15783c51 ("clk: renesas: cpg-mssr: add R8A77980 support")
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 CPG/MSSR driver (again) uses a mix of
clk_readl()/clk_writel() and readl()/writel() to access the clock
registers. Settle on the generic readl()/writel().
Cfr. commit 30ad3cf00e ("clk: renesas: rcar-gen3-cpg: Always use
readl()/writel()").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
On arm32/arm64, there is no reason to use the (soon deprecated)
clk_readl()/clk_writel(). Hence use the generic readl()/writel()
instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Allwinner H6 CCU has a "HDMI Slow Clock", which is currently missing
in the ccu-sun50i-h6 driver.
Add this missing clock to the driver.
Fixes: 542353ea ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Fixes: 322269163a ("clk: hisilicon: add hisi_clk_alloc function.")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for the USB PHY clocks in the CFGCHIP2 syscon
register on TI DA8XX-type SoCs.
The USB0 (USB 2.0) PHY clock is an interesting case because it calls
clk_enable() in a reentrant way. The USB 2.0 PSC only has to be enabled
temporarily while we are locking the PLL, which takes place during the
clk_enable() callback.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This adds a new driver for the gate and multiplexer clocks in the
CFGCHIPn syscon registers on TI DA8XX-type SoCs.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>