XLP3XX includes an on-chip SATA controller with 4 ports. The
controller needs glue logic initialization and PCI fixup before
it can be used with the standard AHCI driver.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6872/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In XLP9XX, the interrupt routing table for MSI-X has been moved to the
PCIe controller's config space from PIC. There are also 32 MSI-X
interrupts available per link on XLP9XX.
Update XLP MSI/MSI-X code to handle this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: g@linux-mips.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6912/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the XLP5XX processor which is an 8 core variant of the
XLP9XX. Add XLP5XX cases to code which earlier handled XLP9XX.
Signed-off-by: Yonghong Song <ysong@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6871/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Calculate XLP 9XX and 2XX core frequency from the per-core PLL. This
should give the correct value for all board configurations.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6870/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update PIC frequency calculation for XLP9XX and 2XX processors using
the correct PLL registers. This should work for all possible board
configurations.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6876/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the compatible property to the PIC entry. Also fix up the nodename
to use the correct address.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6869/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add IRQ to IRT (PIC interupt table index) mapping for SATA, GPIO, NAND
and SPI interfaces on the XLP SoC. Fix offsets for few blocks and add
device IDs for a few blocks.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6911/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ELPA bit needs to be set in the PAGEGRAIN register to enable
access to >64GB physical address. Update reset.S to do this from
every hardware thread.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update thread wakeup function to use scratch registers for saving SP and
RA. Move the register restore code needed for thread 0 to the calling
function. This reduces the size of code copied to the reset vector.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6910/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The macros in topology.h need CONFIG_SMP, and the uniprocessor compilation
fails due to this. Wrap the macros in an ifdef so that uniprocessor works.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6863/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds initial support for BPF-JIT on MIPS
Tested on mips32 LE/BE and mips64 BE/n64 using
dhcp, ping and various tcpdump filters.
Benchmarking:
Assuming the remote MIPS target uses 192.168.154.181
as its IP address, and the local host uses 192.168.154.136,
the following results can be obtained using the following
tcpdump filter (catches no frames) and a simple
'time ping -f -c 1000000' command.
[root@(none) ~]# tcpdump -p -n -s 0 -i eth0 net 10.0.0.0/24 -d
(000) ldh [12]
(001) jeq #0x800 jt 2 jf 8
(002) ld [26]
(003) and #0xffffff00
(004) jeq #0xa000000 jt 16 jf 5
(005) ld [30]
(006) and #0xffffff00
(007) jeq #0xa000000 jt 16 jf 17
(008) jeq #0x806 jt 10 jf 9
(009) jeq #0x8035 jt 10 jf 17
(010) ld [28]
(011) and #0xffffff00
(012) jeq #0xa000000 jt 16 jf 13
(013) ld [38]
(014) and #0xffffff00
(015) jeq #0xa000000 jt 16 jf 17
(016) ret #65535
- BPF-JIT Disabled
real 1m38.005s
user 0m1.510s
sys 0m6.710s
- BPF-JIT Enabled
real 1m35.215s
user 0m1.200s
sys 0m4.140s
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6736/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6733/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6732/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6731/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6730/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Markos Chandras <markos.chandras@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Resolved conflict.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Fixed conflict due to other preceeding conflicts.]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6726/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It will be used later on by bpf-jit
[ralf@linux-mips.org: Fixed conflict with
49e9529b9d [MIPS: uasm: add jalr instruction].
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/6725/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sometimes it's useful to let the user, while doing performance research,
know what in the IEEE754 exceptions has caused many times of FP emulation
when running a specific application. This patch adds 5 more files to
/sys/kernel/debug/mips/fpuemustats/, whose filenames begin with "ieee754".
These stats are in addition to the existing cp1ops, cp1xops, errors, loads
and stores, which may not be useful in understanding the reasons of ieee754
exceptions.
[ralf@linux-mips.org: Fixed reject due to other changes to the kernel
FP assist software.]
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Cc: james.hogan@imgtec.com
Patchwork: http://patchwork.linux-mips.org/patch/7044/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch was tested on devices with 64 MiB and 256 MiB of RAM.
It documents every part nicely and drops this hacky part of code:
max = off | ((128 << 20) - 1);
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/6808/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add interface mode detection for Octeon II. This is necessary to detect
the interface modes correctly on the UBNT E200 board. Code is taken
from the UBNT GPL source release, with some alterations: SRIO, ILK and
RXAUI interface modes are removed and instead return disabled as these
modes are not currently supported.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Tested-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CONFIG_MIPS_CPS SMP implementation should be able to handle all
cases the CONFIG_MIPS_CMP implementation does, but without requiring
bootloader assistance. It is also required in order to make use of
features such as hotplug & cpuidle core power gating. Enable it by
default for Malta configs that previously enabled the now deprecated
CONFIG_MIPS_CMP, and disable the latter. The local version suffix "cmp"
is removed rather than replaced with "cps" since there are other ways to
tell that the CPS SMP implementation is in use (the "VPE topology" line
in the boot log being one).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds a cpuidle driver for systems based around the MIPS
Coherent Processing System (CPS) architecture. It supports four idle
states:
- The standard MIPS wait instruction.
- The non-coherent wait, clock gated & power gated states exposed by
the recently added pm-cps layer.
The pm-cps layer is used to enter all the deep idle states. Since cores
in the clock or power gated states cannot service interrupts, the
gic_send_ipi_single function is modified to send a power up command for
the appropriate core to the CPC in cases where the target CPU has marked
itself potentially incoherent.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch simply includes the cpuidle Kconfig entries in preparation
for cpuidle drivers used on MIPS systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Defines a macro intended to allow trivial use of the regular MIPS wait
instruction from cpuidle drivers, which may simply invoke the macro
within their array of states.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Rather than hardcoding CCA=0x5 for secondary cores, re-use the CCA from
the boot CPU. This allows overrides of the CCA using the cca= kernel
parameter to take effect on all CPUs for consistency.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch sets a default CCA suited for use with multi-core SMP on all
current MIPS CPS based systems. It may still be overriden by the cca=
argument on the kernel command line.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
If the user or bootloader sets the CCA to a value which is not suited
for multi-core SMP (ie. anything non-coherent) then limit the system to
using only a single core and warn the user.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds support for offlining CPUs via hotplug when using the
CONFIG_MIPS_CPS SMP implementation. When a CPU is offlined one of 2
things will happen:
- If the CPU is part of a core which implements the MT ASE and there
is at least one other VPE online within that core then the VPE will
be halted by settings its TCHalt bit.
- Otherwise if supported the core will be powered down via the CPC.
- Otherwise the CPU will hang by executing an infinite loop.
Bringing CPUs back online is then a process of either clearing the
appropriate VPEs TCHalt bit or powering up the appropriate core via the
CPC. Throughout the process the struct core_boot_config vpe_mask field
must be maintained such that mips_cps_boot_vpes will start & stop the
correct VPEs.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds code to generate entry & exit code for various low power
states available on systems based around the MIPS Coherent Processing
System architecture (ie. those with a Coherence Manager, Global
Interrupt Controller & for >=CM2 a Cluster Power Controller). States
supported are:
- Non-coherent wait. This state first leaves the coherent domain and
then executes a regular MIPS wait instruction. Power savings are
found from the elimination of coherency interventions between the
core and any other coherent requestors in the system.
- Clock gated. This state leaves the coherent domain and then gates
the clock input to the core. This removes all dynamic power from the
core but leaves the core at the mercy of another to restart its
clock. Register state is preserved, but the core can not service
interrupts whilst its clock is gated.
- Power gated. This deepest state removes all power input to the core.
All register state is lost and the core will restart execution from
its BEV when another core powers it back up. Because register state
is lost this state requires cooperation with the CONFIG_MIPS_CPS SMP
implementation in order for the core to exit the state successfully.
The code will detect which states are available on the current system
during boot & generate the entry/exit code for those states. This will
be used by cpuidle & hotplug implementations.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The core which the CPC core-other region relates to is based upon the
core-local core-other addressing register. As its name suggests this
register is shared between all VPEs within a core, and if there is a
possibility that multiple VPEs within a core will attempt to access
another core simultaneously then locking is required. This wasn't
previously a problem with the only user being cpu0 during boot, but will
be an issue once hotplug is implemented & may race with other users such
as cpuidle.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The start of mips_cps_core_entry is patched in order to provide the code
with the address of the CM register region at a point where it will be
running non-coherent with the rest of the system. However the cache
wasn't being flushed after that patching which could in principle lead
to secondary cores using an invalid CM base address.
The patching is moved to cps_prepare_cpus since local_flush_icache_range
has not been initialised at the point cps_smp_setup is called.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The core power down state for cpuidle will require that the CPS SMP
implementation is in use. This patch provides a mips_cps_smp_in_use
function which determines whether or not the CPS SMP implementation is
currently in use.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
When hotplug and/or a powered down idle state are supported cases will
arise where a non-zero VPE must be brought online without VPE 0, and it
where multiple VPEs must be onlined simultaneously. This patch prepares
for that by:
- Splitting struct boot_config into core & VPE boot config structures,
allocated one per core or VPE respectively. This allows for multiple
VPEs to be onlined simultaneously without clobbering each others
configuration.
- Indicating which VPEs should be online within a core at any given
time using a bitmap. This allows multiple VPEs to be brought online
simultaneously and also indicates to VPE 0 whether it should halt
after starting any non-zero VPEs that should be online within the
core. For example if all VPEs within a core are offlined via hotplug
and the user onlines the second VPE within that core:
1) The core will be powered up.
2) VPE 0 will run from the BEV (ie. mips_cps_core_entry) to
initialise the core.
3) VPE 0 will start VPE 1 because its bit is set in the cores
bitmap.
4) VPE 0 will halt itself because its bit is clear in the cores
bitmap.
- Moving the core & VPE initialisation to assembly code which does not
make any use of the stack. This is because if a non-zero VPE is to
be brought online in a powered down core then when VPE 0 of that
core runs it may not have a valid stack, and even if it did then
it's messy to run through parts of generic kernel code on VPE 0
before starting the correct VPE.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch allows use of the MT ASE yield instruction from uasm. It will
be used by a subsequent patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
