In preparation for allowing a different mechanism to register DSA switch
devices and driver, update dsa_of_probe and dsa_of_remove to take a
struct device pointer since neither of these two functions uses the
struct platform_device pointer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timewait sockets now share a common base with established sockets.
inet_twsk_diag_dump() can use inet_diag_bc_sk() instead of duplicating
code, granted that inet_diag_bc_sk() does proper userlocks
initialization.
twsk_build_assert() will catch any future changes that could break
the assumptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With some mss values, it is possible tcp_xmit_size_goal() puts
one segment more in TSO packet than tcp_tso_autosize().
We send then one TSO packet followed by one single MSS.
It is not a serious bug, but we can do slightly better, especially
for drivers using netif_set_gso_max_size() to lower gso_max_size.
Using same formula avoids these corner cases and makes
tcp_xmit_size_goal() a bit faster.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 605ad7f184 ("tcp: refine TSO autosizing")
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip/udp bearer can be configured in a point-to-point
mode by specifying both local and remote ip/hostname,
or it can be enabled in multicast mode, where links are
established to all tipc nodes that have joined the same
multicast group. The multicast IP address is generated
based on the TIPC network ID, but can be overridden by
using another multicast address as remote ip.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The payload area following the TIPC discovery message header is an
opaque area defined by the media. INT_H_SIZE was enough for
Ethernet/IB/IPv4 but needs to be expanded to carry IPv6 addressing
information.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Don't truncate ethernet protocol type to u8 in nft_compat, from
Arturo Borrero.
2) Fix several problems in the addition/deletion of elements in nf_tables.
3) Fix module refcount leak in ip_vs_sync, from Julian Anastasov.
4) Fix a race condition in the abort path in the nf_tables transaction
infrastructure. Basically aborted rules can show up as active rules
until changes are unrolled, oneliner from Patrick McHardy.
5) Check for overflows in the data area of the rule, also from Patrick.
6) Fix off-by-one in the per-rule user data size field. This introduces
a new nft_userdata structure that is placed at the beginning of the
user data area that contains the length to save some bits from the
rule and we only need one bit to indicate its presence, from Patrick.
7) Fix rule replacement error path, the replaced rule is deleted on
error instead of leaving it in place. This has been fixed by relying
on the abort path to undo the incomplete replacement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_check_defrag() may be used by af_packet to defragment outgoing packets.
skb_network_offset() of af_packet's outgoing packets is not zero.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes this build error:
net/mpls/af_mpls.c: In function 'resize_platform_label_table':
net/mpls/af_mpls.c:767:4: error: implicit declaration of function 'vzalloc' [-Werror=implicit-function-declaration]
labels = vzalloc(size);
^
Fixes: 7720c01f3f ("mpls: Add a sysctl to control the size of the mpls label table")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* JUMP and GOTO are equivalent except for JUMP pushing the current
context to the stack
* RETURN and implicit RETURN (CONTINUE) are equivalent except that
the logged rule number differs
Result:
nft_do_chain | -112
1 function changed, 112 bytes removed, diff: -112
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The tracing code is squeezed between multiple related parts of the
evaluation code, move it out. Also add an inline wrapper for the
reoccuring test for skb->nf_trace.
Small code savings in nft_do_chain():
nft_trace_packet | -137
nft_do_chain | -8
2 functions changed, 145 bytes removed, diff: -145
net/netfilter/nf_tables_core.c:
__nft_trace_packet | +137
1 function changed, 137 bytes added, diff: +137
net/netfilter/nf_tables_core.o:
3 functions changed, 137 bytes added, 145 bytes removed, diff: -8
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xt_cluster supersedes ipt_CLUSTERIP since it can be also used in
gateway configurations (not only from the backend side).
ipt_CLUSTER is also known to leak the netdev that it uses on
device removal, which requires a rather large fix to workaround
the problem: http://patchwork.ozlabs.org/patch/358629/
So let's deprecate this so we can probably kill code this in the
future.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This extends the design in commit 958501163d ("bridge: Add support for
IEEE 802.11 Proxy ARP") with optional set of rules that are needed to
meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The
previously added BR_PROXYARP behavior is left as-is and a new
BR_PROXYARP_WIFI alternative is added so that this behavior can be
configured from user space when required.
In addition, this enables proxyarp functionality for unicast ARP
requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible
to use unicast as well as broadcast for these frames.
The key differences in functionality:
BR_PROXYARP:
- uses the flag on the bridge port on which the request frame was
received to determine whether to reply
- block bridge port flooding completely on ports that enable proxy ARP
BR_PROXYARP_WIFI:
- uses the flag on the bridge port to which the target device of the
request belongs
- block bridge port flooding selectively based on whether the proxyarp
functionality replied
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes service discovery behaviour, when provided uuid filter
is empty and HCI_QUIRK_STRICT_DUPLICATE_FILTER is set. Before this
patch, empty uuid filter was unable to trigger scan restart, and that
caused inconsistent behaviour in applications.
Example: two DBus clients call BlueZ, one to find all devices with
service abcd, second to find all devices with rssi smaller than -90.
Sum of those filters, that is passed to mgmt_service_scan is empty
filter, with no rssi or uuids set.
That caused kernel not to restart scan when quirk was set.
That was inconsistent with what happen when there's only one of those
two filters set (scan is restarted and reports devices).
To fix that, new variable hdev->discovery.result_filtering was
introduced. It can indicate that filtered scan is running, no matter
what uuid or rssi filter is set.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch refactor code responsible for filtering when service
discovery method is used. Previously this code was mixed with
mgmt_device found logic. Now when it's in one place whole logic can
be greatly simplified. That includes removing no longer necessary
length field and merging checks for eir and scan_rsp.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch moves whole packet filering logic of service discovery
into new function is_filter_match. It's done because logic inside
mgmt_device_found is very complicated and needs some
simplification.
Also having whole logic in one place will allow to simplify it in
the future.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds code to prevent us from attempting to allocate a tnode with
a size larger than what can be represented by size_t.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the fib_table_lookup function so that it is in sync
with the fib_find_node function in terms of the explanation for the index
check based on the bits value.
I have also updated it from doing a mask to just doing a compare as I have
found that seems to provide more options to the compiler as I have seen it
turn this into a shift of the value and test under some circumstances.
In addition I addressed one minor issue in which we kept computing the key
^ n->key when checking the fib aliases. I pulled the xor out of the loop
in order to reduce the number of memory reads in the lookup. As a result
we should save a couple cycles since the xor is only done once much earlier
in the lookup.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib_table was wrapped in several places with an
rcu_read_lock/rcu_read_unlock however after looking over the code I found
several spots where the tables were being accessed as just standard
pointers without any protections. This change fixes that so that all of
the proper protections are in place when accessing the table to take RCU
replacement or removal of the table into account.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we are going to compact the leaf and tnode we first need to make sure
the fields are all in the same place. In that regard I am moving the leaf
pointer which represents the fib_alias hash list to occupy what is
currently the first key_vector pointer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the insert and delete functions make use of
the tnode pointer returned in the fib_find_node call. By doing this we
will not have to rely on the parent pointer in the leaf which will be going
away soon.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the parent pointer is returned by reference in
fib_find_node. By doing this I can use it to find the parent node when I
am performing an insertion and I don't have to look for it again in
fib_insert_node.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that leaf_walk_rcu takes a tnode and a key instead
of the trie and a leaf.
The main idea behind this is to avoid using the leaf parent pointer as that
can have additional overhead in the future as I am trying to reduce the
size of a leaf down to 16 bytes on 64b systems and 12b on 32b systems.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we only call resize on the tnodes, instead of
from each of the leaves. By doing this we can significantly reduce the
amount of time spent resizing as we can update all of the leaves in the
tnode first before we make any determinations about resizing. As a result
we can simply free the tnode in the case that all of the leaves from a
given tnode are flushed instead of resizing with each leaf removed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. For an IPv4 ping socket, ping_check_bind_addr does not check
the family of the socket address that's passed in. Instead,
make it behave like inet_bind, which enforces either that the
address family is AF_INET, or that the family is AF_UNSPEC and
the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
if the socket family is not AF_INET6. Return EAFNOSUPPORT
instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
instead of EINVAL if an incorrect socket address structure is
passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
IPv4, and it cannot easily be made to support IPv4 because
the protocol numbers for ICMP and ICMPv6 are different. This
makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
of making the socket unusable.
Among other things, this fixes an oops that can be triggered by:
int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP);
struct sockaddr_in6 sin6 = {
.sin6_family = AF_INET6,
.sin6_addr = in6addr_any,
};
bind(s, (struct sockaddr *) &sin6, sizeof(sin6));
Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In general, if a transaction object is added to the list successfully,
we can rely on the abort path to undo what we've done. This allows us to
simplify the error handling of the rule replacement path in
nf_tables_newrule().
This implicitly fixes an unnecessary removal of the old rule, which
needs to be left in place if we fail to replace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The NFT_USERDATA_MAXLEN is defined to 256, however we only have a u8
to store its size. Introduce a struct nft_userdata which contains a
length field and indicate its presence using a single bit in the rule.
The length field of struct nft_userdata is also a u8, however we don't
store zero sized data, so the actual length is udata->len + 1.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Check that the space required for the expressions doesn't exceed the
size of the dlen field, which would lead to the iterators crashing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A race condition exists in the rule transaction code for rules that
get added and removed within the same transaction.
The new rule starts out as inactive in the current and active in the
next generation and is inserted into the ruleset. When it is deleted,
it is additionally set to inactive in the next generation as well.
On commit the next generation is begun, then the actions are finalized.
For the new rule this would mean clearing out the inactive bit for
the previously current, now next generation.
However nft_rule_clear() clears out the bits for *both* generations,
activating the rule in the current generation, where it should be
deactivated due to being deleted. The rule will thus be active until
the deletion is finalized, removing the rule from the ruleset.
Similarly, when aborting a transaction for the same case, the undo
of insertion will remove it from the RCU protected rule list, the
deletion will clear out all bits. However until the next RCU
synchronization after all operations have been undone, the rule is
active on CPUs which can still see the rule on the list.
Generally, there may never be any modifications of the current
generations' inactive bit since this defeats the entire purpose of
atomicity. Change nft_rule_clear() to only touch the next generations
bit to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Unlike IPv4 this code notifies on all cases where mpls routes
are added or removed and it never automatically removes routes.
Avoiding both the userspace confusion that is caused by omitting
route updates and the possibility of a flood of netlink traffic
when an interface goes doew.
For now reserved labels are handled automatically and userspace
is not notified.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds two new netlink routing attributes:
RTA_VIA and RTA_NEWDST.
RTA_VIA specifies the specifies the next machine to send a packet to
like RTA_GATEWAY. RTA_VIA differs from RTA_GATEWAY in that it
includes the address family of the address of the next machine to send
a packet to. Currently the MPLS code supports addresses in AF_INET,
AF_INET6 and AF_PACKET. For AF_INET and AF_INET6 the destination mac
address is acquired from the neighbour table. For AF_PACKET the
destination mac_address is specified in the netlink configuration.
I think raw destination mac address support with the family AF_PACKET
will prove useful. There is MPLS-TP which is defined to operate
on machines that do not support internet packets of any flavor. Further
seem to be corner cases where it can be useful. At this point
I don't care much either way.
RTA_NEWDST specifies the destination address to forward the packet
with. MPLS typically changes it's destination address at every hop.
For a swap operation RTA_NEWDST is specified with a length of one label.
For a push operation RTA_NEWDST is specified with two or more labels.
For a pop operation RTA_NEWDST is not specified or equivalently an emtpy
RTAN_NEWDST is specified.
Those new netlink attributes are used to implement handling of rt-netlink
RTM_NEWROUTE, RTM_DELROUTE, and RTM_GETROUTE messages, to maintain the
MPLS label table.
rtm_to_route_config parses a netlink RTM_NEWROUTE or RTM_DELROUTE message,
verify no unhandled attributes or unhandled values are present and sets
up the data structures for mpls_route_add and mpls_route_del.
I did my best to match up with the existing conventions with the caveats
that MPLS addresses are all destination-specific-addresses, and so
don't properly have a scope.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading and writing addresses in network byte order in netlink is
traditional and I see no reason to change that. MPLS is interesting
as effectively it has variabely length addresses (the MPLS label
stack). To represent these variable length addresses in netlink
I use a valid MPLS label stack (complete with stop bit).
This achieves two things: a well defined existing format is used,
and the data can be interpreted without looking at it's length.
Not needed to look at the length to decode the variable length
network representation allows existing userspace functions
such as inet_ntop to be used without needed to change their
prototype.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mpls_route_add and mpls_route_del implement the basic logic for adding
and removing Next Hop Label Forwarding Entries from the MPLS input
label map. The addition and subtraction is done in a way that is
consistent with how the existing routing table in Linux are
maintained. Thus all of the work to deal with NLM_F_APPEND,
NLM_F_EXCL, NLM_F_REPLACE, and NLM_F_CREATE.
Cases that are not clearly defined such as changing the interpretation
of the mpls reserved labels is not allowed.
Because it seems like the right thing to do adding an MPLS route without
specifying an input label and allowing the kernel to pick a free label
table entry is supported. The implementation is currently less than optimal
but that can be changed.
As I don't have anything else to test with only ethernet and the loopback
device are the only two device types currently supported for forwarding
MPLS over.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl gives two benefits. By defaulting the table size to 0
mpls even when compiled in and enabled defaults to not forwarding
any packets. This prevents unpleasant surprises for users.
The other benefit is that as mpls labels are allocated locally a dense
table a small dense label table may be used which saves memory and
is extremely simple and efficient to implement.
This sysctl allows userspace to choose the restrictions on the label
table size userspace applications need to cope with.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds a new Kconfig option MPLS_ROUTING.
The core of this change is the code to look at an mpls packet received
from another machine. Look that packet up in a routing table and
forward the packet on.
Support of MPLS over ATM is not considered or attempted here. This
implemntation follows RFC3032 and implements the MPLS shim header that
can pass over essentially any network.
What RFC3021 refers to as the as the Incoming Label Map (ILM) I call
net->mpls.platform_label[]. What RFC3031 refers to as the Next Label
Hop Forwarding Entry (NHLFE) I call mpls_route. Though calling it the
label fordwarding information base (lfib) might also be valid.
Further the implemntation forwards packets as described in RFC3032.
There is no need and given the original motivation for MPLS a strong
discincentive to have a flexible label forwarding path. In essence
the logic is the topmost label is read, looked up, removed, and
replaced by 0 or more new lables and the sent out the specified
interface to it's next hop.
Quite a few optional features are not implemented here. Among them
are generation of ICMP errors when the TTL is exceeded or the packet
is larger than the next hop MTU (those conditions are detected and the
packets are dropped instead of generating an icmp error). The traffic
class field is always set to 0. The implementation focuses on IP over
MPLS and does not handle egress of other kinds of protocols.
Instead of implementing coordination with the neighbour table and
sorting out how to input next hops in a different address family (for
which there is value). I was lazy and implemented a next hop mac
address instead. The code is simpler and there are flavor of MPLS
such as MPLS-TP where neither an IPv4 nor an IPv6 next hop is
appropriate so a next hop by mac address would need to be implemented
at some point.
Two new definitions AF_MPLS and PF_MPLS are exposed to userspace.
Decoding the mpls header must be done by first byeswapping a 32bit bit
endian word into the local cpu endian and then bit shifting to extract
the pieces. There is no C bit-field that can represent a wire format
mpls header on a little endian machine as the low bits of the 20bit
label wind up in the wrong half of third byte. Therefore internally
everything is deal with in cpu native byte order except when writing
to and reading from a packet.
For management simplicity if a label is configured to forward out
an interface that is down the packet is dropped early. Similarly
if an network interface is removed rt_dev is updated to NULL
(so no reference is preserved) and any packets for that label
are dropped. Keeping the label entries in the kernel allows
the kernel label table to function as the definitive source
of which labels are allocated and which are not.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactoring is needed to allow more than just mpls gso
support to be built into the mpls moddule.
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For MPLS I am building the code so that either the neighbour mac
address can be specified or we can have a next hop in ipv4 or ipv6.
The kind of next hop we have is indicated by the neighbour table
pointer. A neighbour table pointer of NULL is a link layer address.
A non-NULL neighbour table pointer indicates which neighbour table and
thus which address family the next hop address is in that we need to
look up.
The code either sends a packet directly or looks up the appropriate
neighbour table entry and sends the packet.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at the mpls code I found myself writing yet another
version of neigh_lookup_noref. We currently have __ipv4_lookup_noref
and __ipv6_lookup_noref.
So to make my work a little easier and to make it a smidge easier to
verify/maintain the mpls code in the future I stopped and wrote
___neigh_lookup_noref. Then I rewote __ipv4_lookup_noref and
__ipv6_lookup_noref in terms of this new function. I tested my new
version by verifying that the same code is generated in
ip_finish_output2 and ip6_finish_output2 where these functions are
inlined.
To get to ___neigh_lookup_noref I added a new neighbour cache table
function key_eq. So that the static size of the key would be
available.
I also added __neigh_lookup_noref for people who want to to lookup
a neighbour table entry quickly but don't know which neibhgour table
they are going to look up.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the STP timer fires, it can call br_ifinfo_notify(),
which in turn ends up in the new br_get_link_af_size().
This function is annotated to be using RTNL locking, which
clearly isn't the case here, and thus lockdep warns:
===============================
[ INFO: suspicious RCU usage. ]
3.19.0+ #569 Not tainted
-------------------------------
net/bridge/br_private.h:204 suspicious rcu_dereference_protected() usage!
Fix this by doing RCU locking here.
Fixes: b7853d73e3 ("bridge: add vlan info to bridge setlink and dellink notification messages")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd fixes from Bruce Fields:
"Three miscellaneous bugfixes, most importantly the clp->cl_revoked
bug, which we've seen several reports of people hitting"
* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
sunrpc: integer underflow in rsc_parse()
nfsd: fix clp->cl_revoked list deletion causing softlock in nfsd
svcrpc: fix memory leak in gssp_accept_sec_context_upcall
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the ax25 stack calls dev_queue_xmit it always calls
ax25_type_trans which sets skb->protocol to ETH_P_AX25.
Which means that by looking at the protocol type it is possible to
detect IP packets that have not been munged by the ax25 stack in
ndo_start_xmit and call a function to munge them.
Rename ax25_neigh_xmit to ax25_ip_xmit and tweak the return type and
value to be appropriate for an ndo_start_xmit function.
Update all of the ax25 devices to test the protocol type for ETH_P_IP
and return ax25_ip_xmit as the first thing they do. This preserves
the existing semantics of IP packet processing, but the timing will be
a little different as the IP packets now pass through the qdisc layer
before reaching the ax25 ip packet processing.
Remove the now unnecessary ax25 neighbour table operations.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set actions consist of a regular OVS_KEY_ATTR_* attribute nested inside
of a OVS_ACTION_ATTR_SET action attribute. When converting masked actions
back to regular set actions, the inner attribute length was not changed,
ie, double the length being serialized. This patch fixes the bug.
Fixes: 83d2b9b ("net: openvswitch: Support masked set actions.")
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WAIT_FOR_DEMON code is directly undefined at the beginning
of signaling.c since initial git version and thus never compiled.
This also removes buggy current->state direct access.
Suggested-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
make build fail if structure no longer fits into ->cb storage.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).
Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge reject handling is not straightforward, there are many subtle
differences depending on configuration.
skb->dev is either the bridge port (PRE_ROUTING) or the bridge
itself (INPUT), so we need to use indev instead.
Also, checksum validation will only work reliably if we trim skb
according to the l3 header size.
While at it, add csum validation for ipv6 and skip existing tests
if skb was already checked e.g. by GRO.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
tcp resets are never emitted if the packet that triggers the
reject/reset has an invalid checksum.
For icmp error responses there was no such check.
It allows to distinguish icmp response generated via
iptables -I INPUT -p udp --dport 42 -j REJECT
and those emitted by network stack (won't respond if csum is invalid,
REJECT does).
Arguably its possible to avoid this by using conntrack and only
using REJECT with -m conntrack NEW/RELATED.
However, this doesn't work when connection tracking is not in use
or when using nf_conntrack_checksum=0.
Furthermore, sending errors in response to invalid csums doesn't make
much sense so just add similar test as in nf_send_reset.
Validate csum if needed and only send the response if it is ok.
Reference: http://bugzilla.redhat.com/show_bug.cgi?id=1169829
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Having a dst helps a little bit for teql but is fundamentally
unnecessary and there are code paths where a dst is not available that
it would be nice to use the neighbour cache.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add protocol to neigh_tbl so that dst->ops->protocol is not needed
- Acquire the device from neigh->dev
This results in a neigh_hh_init that will cache the samve values
regardless of the packets flowing through it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no more callers so kill this function.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there are no more users kill dev_rebuild_header and all of it's
implementations.
This is long overdue.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have ax25_neigh_output perform ordinary arp resolution before calling
ax25_neigh_xmit.
Call dev_hard_header in ax25_neigh_output with a destination address so
it will not fail, and the destination mac address will not need to be
set in ax25_neigh_xmit.
Remove arp_find from ax25_neigh_xmit (the ordinary arp resolution added
to ax25_neigh_output removes the need for calling arp_find).
Document how close ax25_neigh_output is to neigh_resolve_output.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rename ax25_rebuild_header to ax25_neigh_xmit and call it from
ax25_neigh_output directly. The rename is to make it clear
that this is not a rebuild_header operation.
- Remove ax25_rebuild_header from ax25_header_ops.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller is now is ax25_neigh_construct so move
neigh_compat_output into ax25_ip.c make it static and rename it
ax25_neigh_output.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The special case has been pushed out into ax25_neigh_construct so there
is no need to keep this code in arp.c
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AX25 already has it's own private arp cache operations to isolate
it's abuse of dev_rebuild_header to transmit packets. Add a function
ax25_neigh_construct that will allow all of the ax25 devices to
force using these operations, so that the generic arp code does
not need to.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user is in ax25_ip.c so stop exporting these functions.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patterned after the similar code in net/rom this turns out
to be a trivial obviously correct transmformation.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not setting the destination address is a bug that I suspect causes no
problems today, as only the arp code seems to call dev_hard_header and
the description I have of rose is that it is expected to be used with a
static neigbour table.
I have derived the offset and the length of the rose destination address
from rose_rebuild_header where arp_find calls neigh_ha_snapshot to set
the destination address.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely (impossible?) event that we attempt to transmit
an ax25 packet over a non-ax25 device free the skb so we don't
leak it.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-hams@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A small batch with accumulated updates in nf-next, mostly IPVS updates,
they are:
1) Add 64-bits stats counters to IPVS, from Julian Anastasov.
2) Move NETFILTER_XT_MATCH_ADDRTYPE out of NETFILTER_ADVANCED as docker
seem to require this, from Anton Blanchard.
3) Use boolean instead of numeric value in set_match_v*(), from
coccinelle via Fengguang Wu.
4) Allows rescheduling of new connections in IPVS when port reuse is
detected, from Marcelo Ricardo Leitner.
5) Add missing bits to support arptables extensions from nft_compat,
from Arturo Borrero.
Patrick is preparing a large batch to enhance the set infrastructure,
named expressions among other things, that should follow up soon after
this batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both sk_attach_filter() and sk_attach_bpf() are setting up sk_filter,
charging skmem and attaching it to the socket after we got the eBPF
prog up and ready. Lets refactor that into a common helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After TIPC doesn't depend on iocb argument in its internal
implementations of sendmsg() and recvmsg() hooks defined in proto
structure, no any user is using iocb argument in them at all now.
Then we can drop the redundant iocb argument completely from kinds of
implementations of both sendmsg() and recvmsg() in the entire
networking stack.
Cc: Christoph Hellwig <hch@lst.de>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the iocb argument is used to idenfiy whether or not socket
lock is hold before tipc_sendmsg()/tipc_send_stream() is called. But
this usage prevents iocb argument from being dropped through sendmsg()
at socket common layer. Therefore, in the commit we introduce two new
functions called __tipc_sendmsg() and __tipc_send_stream(). When they
are invoked, it assumes that their callers have taken socket lock,
thereby avoiding the weird usage of iocb argument.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to arptables extensions from nft_compat.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 977750076d ("af_packet: add interframe drop cmsg (v6)")
unionized skb->mark and skb->dropcount in order to allow recording
of the socket drop count while maintaining struct sk_buff size.
skb->dropcount was introduced since there was no available room
in skb->cb[] in packet sockets. However, its introduction led to
the inability to export skb->mark, or any other aliased field to
userspace if so desired.
Moving the dropcount metric to skb->cb[] eliminates this problem
at the expense of 4 bytes less in skb->cb[] for protocol families
using it.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[], use
a common function in order to set dropcount in struct sk_buff.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[] use a common
macro in protocol families using skb->cb[] for ancillary data to
validate available room in skb->cb[].
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of an effort to move skb->dropcount to skb->cb[], 4 bytes
of additional room are needed in skb->cb[] in packet sockets.
Store the skb original length in the first two fields of sockaddr_ll
(sll_family and sll_protocol) as they can be derived from the skb when
needed.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3b885787ea ("net: Generalize socket rx gap / receive queue overflow cmsg")
allowed receiving packet dropcount information as a socket level option.
RXRPC sockets recvmsg function was changed to support this by calling
sock_recv_ts_and_drops() instead of sock_recv_timestamp().
However, protocol families wishing to receive dropcount should call
sock_queue_rcv_skb() or set the dropcount specifically (as done
in packet_rcv()). This was not done for rxrpc and thus this feature
never worked on these sockets.
Formalizing this by not calling sock_recv_ts_and_drops() in rxrpc as
part of an effort to move skb->dropcount into skb->cb[]
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert boolean fields incoming and req_start to bit fields and move
force_active in order save space in bt_skb_cb in an effort to use
a portion of skb->cb[] for storing skb->dropcount.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct hci_req_ctrl is never used outside of struct bt_skb_cb;
Inlining it frees 8 bytes on a 64 bit system in skb->cb[] allowing
the addition of more ancillary data.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work extends the "classic" BPF programmable tc classifier by
extending its scope also to native eBPF code!
This allows for user space to implement own custom, 'safe' C like
classifiers (or whatever other frontend language LLVM et al may
provide in future), that can then be compiled with the LLVM eBPF
backend to an eBPF elf file. The result of this can be loaded into
the kernel via iproute2's tc. In the kernel, they can be JITed on
major archs and thus run in native performance.
Simple, minimal toy example to demonstrate the workflow:
#include <linux/ip.h>
#include <linux/if_ether.h>
#include <linux/bpf.h>
#include "tc_bpf_api.h"
__section("classify")
int cls_main(struct sk_buff *skb)
{
return (0x800 << 16) | load_byte(skb, ETH_HLEN + __builtin_offsetof(struct iphdr, tos));
}
char __license[] __section("license") = "GPL";
The classifier can then be compiled into eBPF opcodes and loaded
via tc, for example:
clang -O2 -emit-llvm -c cls.c -o - | llc -march=bpf -filetype=obj -o cls.o
tc filter add dev em1 parent 1: bpf cls.o [...]
As it has been demonstrated, the scope can even reach up to a fully
fledged flow dissector (similarly as in samples/bpf/sockex2_kern.c).
For tc, maps are allowed to be used, but from kernel context only,
in other words, eBPF code can keep state across filter invocations.
In future, we perhaps may reattach from a different application to
those maps e.g., to read out collected statistics/state.
Similarly as in socket filters, we may extend functionality for eBPF
classifiers over time depending on the use cases. For that purpose,
cls_bpf programs are using BPF_PROG_TYPE_SCHED_CLS program type, so
we can allow additional functions/accessors (e.g. an ABI compatible
offset translation to skb fields/metadata). For an initial cls_bpf
support, we allow the same set of helper functions as eBPF socket
filters, but we could diverge at some point in time w/o problem.
I was wondering whether cls_bpf and act_bpf could share C programs,
I can imagine that at some point, we introduce i) further common
handlers for both (or even beyond their scope), and/or if truly needed
ii) some restricted function space for each of them. Both can be
abstracted easily through struct bpf_verifier_ops in future.
The context of cls_bpf versus act_bpf is slightly different though:
a cls_bpf program will return a specific classid whereas act_bpf a
drop/non-drop return code, latter may also in future mangle skbs.
That said, we can surely have a "classify" and "action" section in
a single object file, or considered mentioned constraint add a
possibility of a shared section.
The workflow for getting native eBPF running from tc [1] is as
follows: for f_bpf, I've added a slightly modified ELF parser code
from Alexei's kernel sample, which reads out the LLVM compiled
object, sets up maps (and dynamically fixes up map fds) if any, and
loads the eBPF instructions all centrally through the bpf syscall.
The resulting fd from the loaded program itself is being passed down
to cls_bpf, which looks up struct bpf_prog from the fd store, and
holds reference, so that it stays available also after tc program
lifetime. On tc filter destruction, it will then drop its reference.
Moreover, I've also added the optional possibility to annotate an
eBPF filter with a name (e.g. path to object file, or something
else if preferred) so that when tc dumps currently installed filters,
some more context can be given to an admin for a given instance (as
opposed to just the file descriptor number).
Last but not least, bpf_prog_get() and bpf_prog_put() needed to be
exported, so that eBPF can be used from cls_bpf built as a module.
Thanks to 60a3b2253c ("net: bpf: make eBPF interpreter images
read-only") I think this is of no concern since anything wanting to
alter eBPF opcode after verification stage would crash the kernel.
[1] http://git.breakpoint.cc/cgit/dborkman/iproute2.git/log/?h=ebpf
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
is_gpl_compatible and prog_type should be moved directly into bpf_prog
as they stay immutable during bpf_prog's lifetime, are core attributes
and they can be locked as read-only later on via bpf_prog_select_runtime().
With a bit of rearranging, this also allows us to shrink bpf_prog_aux
to exactly 1 cacheline.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discussed recently and at netconf/netdev01, we want to prevent making
bpf_verifier_ops registration available for modules, but have them at a
controlled place inside the kernel instead.
The reason for this is, that out-of-tree modules can go crazy and define
and register any verfifier ops they want, doing all sorts of crap, even
bypassing available GPLed eBPF helper functions. We don't want to offer
such a shiny playground, of course, but keep strict control to ourselves
inside the core kernel.
This also encourages us to design eBPF user helpers carefully and
generically, so they can be shared among various subsystems using eBPF.
For the eBPF traffic classifier (cls_bpf), it's a good start to share
the same helper facilities as we currently do in eBPF for socket filters.
That way, we have BPF_PROG_TYPE_SCHED_CLS look like it's own type, thus
one day if there's a good reason to diverge the set of helper functions
from the set available to socket filters, we keep ABI compatibility.
In future, we could place all bpf_prog_type_list at a central place,
perhaps.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of CONFIG_BPF_SYSCALL ifdefs in the socket filter code,
now that the BPF internal header can deal with it.
While going over it, I also changed eBPF related functions to a sk_filter
prefix to be more consistent with the rest of the file.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can move bpf_map_ops and bpf_verifier_ops and other structs into ro
section, bpf_map_type_list and bpf_prog_type_list into read mostly.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rxrpc_resend_timeout has an initial value of 4 * HZ; use it as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Typo, 'stop' is never set to true.
Seems intent is to not attempt to retransmit more packets after sendmsg
returns an error.
This change is based on code inspection only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To repeat:
$ sudo ip link del hsr0
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff8187f495>] hsr_del_port+0x15/0xa0
etc...
Bug description:
As part of the hsr master device destruction, hsr_del_port() is called for each of
the hsr ports. At each such call, the master device is updated regarding features
and mtu. When the master device is freed before the slave interfaces, master will
be NULL in hsr_del_port(), which led to a NULL pointer dereference.
Additionally, dev_put() was called on the master device itself in hsr_del_port(),
causing a refcnt error.
A third bug in the same code path was that the rtnl lock was not taken before
hsr_del_port() was called as part of hsr_dev_destroy().
The reporter (Nicolas Dichtel) also said: "hsr_netdev_notify() supposes that the
port will always be available when the notification is for an hsr interface. It's
wrong. For example, netdev_wait_allrefs() may resend NETDEV_UNREGISTER.". As a
precaution against this, a check for port == NULL was added in hsr_dev_notify().
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: 51f3c60531 ("net/hsr: Move slave init to hsr_slave.c.")
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We did a failed attempt in the past to only use rcu in rtnl dump
operations (commit e67f88dd12 "net: dont hold rtnl mutex during
netlink dump callbacks")
Now that dumps are holding RTNL anyway, there is no need to also
use rcu locking, as it forbids any scheduling ability, like
GFP_KERNEL allocations that controlling path should use instead
of GFP_ATOMIC whenever possible.
This should fix following splat Cong Wang reported :
[ INFO: suspicious RCU usage. ]
3.19.0+ #805 Tainted: G W
include/linux/rcupdate.h:538 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by ip/771:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff8182b8f4>] netlink_dump+0x21/0x26c
#1: (rcu_read_lock){......}, at: [<ffffffff817d785b>] rcu_read_lock+0x0/0x6e
stack backtrace:
CPU: 3 PID: 771 Comm: ip Tainted: G W 3.19.0+ #805
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
0000000000000001 ffff8800d51e7718 ffffffff81a27457 0000000029e729e6
ffff8800d6108000 ffff8800d51e7748 ffffffff810b539b ffffffff820013dd
00000000000001c8 0000000000000000 ffff8800d7448088 ffff8800d51e7758
Call Trace:
[<ffffffff81a27457>] dump_stack+0x4c/0x65
[<ffffffff810b539b>] lockdep_rcu_suspicious+0x107/0x110
[<ffffffff8109796f>] rcu_preempt_sleep_check+0x45/0x47
[<ffffffff8109e457>] ___might_sleep+0x1d/0x1cb
[<ffffffff8109e67d>] __might_sleep+0x78/0x80
[<ffffffff814b9b1f>] idr_alloc+0x45/0xd1
[<ffffffff810cb7ab>] ? rcu_read_lock_held+0x3b/0x3d
[<ffffffff814b9f9d>] ? idr_for_each+0x53/0x101
[<ffffffff817c1383>] alloc_netid+0x61/0x69
[<ffffffff817c14c3>] __peernet2id+0x79/0x8d
[<ffffffff817c1ab7>] peernet2id+0x13/0x1f
[<ffffffff817d8673>] rtnl_fill_ifinfo+0xa8d/0xc20
[<ffffffff810b17d9>] ? __lock_is_held+0x39/0x52
[<ffffffff817d894f>] rtnl_dump_ifinfo+0x149/0x213
[<ffffffff8182b9c2>] netlink_dump+0xef/0x26c
[<ffffffff8182bcba>] netlink_recvmsg+0x17b/0x2c5
[<ffffffff817b0adc>] __sock_recvmsg+0x4e/0x59
[<ffffffff817b1b40>] sock_recvmsg+0x3f/0x51
[<ffffffff817b1f9a>] ___sys_recvmsg+0xf6/0x1d9
[<ffffffff8115dc67>] ? handle_pte_fault+0x6e1/0xd3d
[<ffffffff8100a3a0>] ? native_sched_clock+0x35/0x37
[<ffffffff8109f45b>] ? sched_clock_local+0x12/0x72
[<ffffffff8109f6ac>] ? sched_clock_cpu+0x9e/0xb7
[<ffffffff810cb7ab>] ? rcu_read_lock_held+0x3b/0x3d
[<ffffffff811abde8>] ? __fcheck_files+0x4c/0x58
[<ffffffff811ac556>] ? __fget_light+0x2d/0x52
[<ffffffff817b376f>] __sys_recvmsg+0x42/0x60
[<ffffffff817b379f>] SyS_recvmsg+0x12/0x1c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 0c7aecd4bd ("netns: add rtnl cmd to add and get peer netns ids")
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
-----BEGIN PGP SIGNATURE-----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=H3+7
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2015-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few patches have accumulated, among them the fix for Linus's
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_fastopen_create_child() is static and should not be exported.
tcp4_gso_segment() and tcp6_gso_segment() should be static.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When applicable verify that the caller has permisson to the underlying
network namespace for a newly created network device.
Similary checks exist for the network namespace a network device will
be created in.
Fixes: 317f4810e4 ("rtnl: allow to create device with IFLA_LINK_NETNSID set")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When applicable verify that the caller has permision to create a
network device in another network namespace. This check is already
present when moving a network device between network namespaces in
setlink so all that is needed is to duplicate that check in newlink.
This change almost backports cleanly, but there are context conflicts
as the code that follows was added in v4.0-rc1
Fixes: b51642f6d7 net: Enable a userns root rtnl calls that are safe for unprivilged users
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another TCP issue is triggered by ECN.
Under pressure, receiver gets ECN marks, and send back ACK packets
with ECE TCP flag. Senders enter CA_CWR state.
In this state, tcp_tso_should_defer() is short cut :
if (icsk->icsk_ca_state != TCP_CA_Open)
goto send_now;
This means that about all ACK packets we receive are triggering
a partial send, and because cwnd is kept small, we can only send
a small amount of data for each incoming ACK,
which in return generate more ACK packets.
Allowing CA_Open and CA_CWR states to enable TSO defer in
tcp_tso_should_defer() brings performance back :
TSO autodefer has more chance to defer under pressure.
This patch increases TSO and LRO/GRO efficiency back to normal levels,
and does not impact overall ECN behavior.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With sysctl_tcp_min_tso_segs being 4, it is very possible
that tcp_tso_should_defer() decides not sending last 2 MSS
of initial window of 10 packets. This also applies if
autosizing decides to send X MSS per GSO packet, and cwnd
is not a multiple of X.
This patch implements an heuristic based on age of first
skb in write queue : If it was sent very recently (less than half srtt),
we can predict that no ACK packet will come in less than half rtt,
so deferring might cause an under utilization of our window.
This is visible on initial send (IW10) on web servers,
but more generally on some RPC, as the last part of the message
might need an extra RTT to get delivered.
Tested:
Ran following packetdrill test
// A simple server-side test that sends exactly an initial window (IW10)
// worth of packets.
`sysctl -e -q net.ipv4.tcp_min_tso_segs=4`
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+.1 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7>
+0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 6>
+.1 < . 1:1(0) ack 1 win 257
+0 accept(3, ..., ...) = 4
+0 write(4, ..., 14600) = 14600
+0 > . 1:5841(5840) ack 1 win 457
+0 > . 5841:11681(5840) ack 1 win 457
// Following packet should be sent right now.
+0 > P. 11681:14601(2920) ack 1 win 457
+.1 < . 1:1(0) ack 14601 win 257
+0 close(4) = 0
+0 > F. 14601:14601(0) ack 1
+.1 < F. 1:1(0) ack 14602 win 257
+0 > . 14602:14602(0) ack 2
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TSO relies on ability to defer sending a small amount of packets.
Heuristic is to wait for future ACKS in hope to send more packets at once.
Current algorithm uses a per socket tso_deferred field as a pseudo timer.
This pseudo timer relies on future ACK, but there is no guarantee
we receive them in time.
Fix would be to use a real timer, but cost of such timer is probably too
expensive for typical cases.
This patch changes the logic to test the time of last transmit,
because we should not add bursts of more than 1ms for any given flow.
We've used this patch for about two years at Google, before FQ/pacing
as it would reduce a fair amount of bursts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the exception of infiniband media which does not use media
offsets, the media address is always located at offset 4 in the
media info field as defined by the protocol, so we move the
definition to the generic bearer.h
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC_MEDIA_ADDR_SIZE and TIPC_MEDIA_ADDR_OFFSET names
are misleading, as they actually define the size and offset of
the whole media info field and not the address part. This patch
does not have any functional changes.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bearer is disabled by manual intervention, all links over that
bearer should be purged, indicated with the 'shutting_down' flag.
Otherwise tipc will get confused if a new bearer is enabled using
a different media type.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a subscription request is sent to a topology server
connection, and any error occurs (malformed request, oom
or limit reached) while processing this request, TIPC should
terminate the subscriber connection. While doing so, it tries
to access fields in an already freed (or never allocated)
subscription element leading to a nullpointer exception.
We fix this by removing the subscr_terminate function and
terminate the connection immediately upon any subscription
failure.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIPC name distributor pushes topology updates to the cluster
neighbors. Currently this is done in a unicast manner, and the
skb holding the update is cloned for each cluster member. This
is unnecessary, as we only modify the destnode field in the header
so we change it to do pskb_copy instead.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the leaf_info hash is redundant. By adding the suffix length
to the fib_alias hash list we no longer have need of leaf_info as we can
determine the prefix length from fa_slen. So we can compress things by
dropping the leaf_info structure from fib_trie and instead directly connect
the leaves to the fib_alias hash list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of an empty spot in the alias to store the suffix length so that
we don't need to pull that information from the leaf_info structure.
This patch also makes a slight change to the user statistics. Instead of
incrementing semantic_match_miss once per leaf_info miss we now just
increment it once per leaf if a match was not found.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This replaces the prefix length variable in the leaf_info structure with a
suffix length value, or host identifier length in bits. By doing this it
makes it easier to sort out since the tnodes and leaf are carrying this
value as well since it is compatible with the ->pos field in tnodes.
I also cleaned up one spot that had some list manipulation that could be
simplified. I basically updated it so that we just use hlist_add_head_rcu
instead of calling hlist_add_before_rcu on the first node in the list.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't any advantage to having it as a list and by making it an hlist
we make the fib_alias more compatible with the list_info in terms of the
type of list used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joining multicast group on ethernet level via "ip maddr" command would
not work if we have an Ethernet switch that does igmp snooping since
the switch would not replicate multicast packets on ports that did not
have IGMP reports for the multicast addresses.
Linux vxlan interfaces created via "ip link add vxlan" have the group option
that enables then to do the required join.
By extending ip address command with option "autojoin" we can get similar
functionality for openvswitch vxlan interfaces as well as other tunneling
mechanisms that need to receive multicast traffic. The kernel code is
structured similar to how the vxlan driver does a group join / leave.
example:
ip address add 224.1.1.10/24 dev eth5 autojoin
ip address del 224.1.1.10/24 dev eth5
Signed-off-by: Madhu Challa <challa@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the igmp v4 changes from Eric Dumazet.
959d10f6bbf6("igmp: add __ip_mc_{join|leave}_group()")
These changes are needed to perform igmp v6 join/leave while
RTNL is held.
Make ipv6_sock_mc_join and ipv6_sock_mc_drop wrappers around
__ipv6_sock_mc_join and __ipv6_sock_mc_drop to avoid
proliferation of work queues.
Signed-off-by: Madhu Challa <challa@noironetworks.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all real users of rhashtable default their grow and shrink
decision functions to rht_grow_above_75() and rht_shrink_below_30(),
so that there's currently no need to have this explicitly selectable.
It can/should be generic and private inside rhashtable until a real
use case pops up. Since we can make this private, we'll save us this
additional indirection layer and can improve insertion/deletion time
as well.
Reference: http://patchwork.ozlabs.org/patch/443040/
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event that skb_get_hash is unable to deduce a hash
in udp_flow_src_port we use a consistent random value instead.
This is specified in GRE/UDP draft section 3.2.1:
https://tools.ietf.org/html/draft-ietf-tsvwg-gre-in-udp-encap-04
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc5 warns about passing a const array to hci_test_bit which takes a
non-const pointer:
net/bluetooth/hci_sock.c: In function ‘hci_sock_sendmsg’:
net/bluetooth/hci_sock.c:955:8: warning: passing argument 2 of ‘hci_test_bit’ discards ‘const’ qualifier from pointer target type [-Wdiscarded-array-qualifiers]
&hci_sec_filter.ocf_mask[ogf])) &&
^
net/bluetooth/hci_sock.c:49:19: note: expected ‘void *’ but argument is of type ‘const __u32 (*)[4] {aka const unsigned int (*)[4]}’
static inline int hci_test_bit(int nr, void *addr)
^
So make 'addr' 'const void *'.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
The 'master' parameter of the New CSRK event was recently renamed to
'type', with the old values kept for backwards compatibility as
unauthenticated local/remote keys. This patch updates the code to take
into account the two new (authenticated) values and ensures they get
used based on the security level of the connection that the respective
keys get distributed over.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we call groups_alloc() with invalid values then it's might lead to
memory corruption. For example, with a negative value then we might not
allocate enough for sizeof(struct group_info).
(We're doing this in the caller for consistency with other callers of
groups_alloc(). The other alternative might be to move the check out of
all the callers into groups_alloc().)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Simo Sorce <simo@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The current minstrel_ht rate control behavior is somewhat optimistic in
trying to find optimum TX rate. While this is usually fine for normal
Data frames, there are cases where a more conservative set of retry
parameters would be beneficial to make the connection more robust.
EAPOL frames are critical to the authentication and especially the
EAPOL-Key message 4/4 (the last message in the 4-way handshake) is
important to get through to the AP. If that message is lost, the only
recovery mechanism in many cases is to reassociate with the AP and start
from scratch. This can often be avoided by trying to send the frame with
more conservative rate and/or with more link layer retries.
In most cases, minstrel_ht is currently using the initial EAPOL-Key
frames for probing higher rates and this results in only five link layer
transmission attempts (one at high(ish) MCS and four at MCS0). While
this works with most APs, it looks like there are some deployed APs that
may have issues with the EAPOL frames using HT MCS immediately after
association. Similarly, there may be issues in cases where the signal
strength or radio environment is not good enough to be able to get
frames through even at couple of MCS 0 tries.
The best approach for this would likely to be to reduce the TX rate for
the last rate (3rd rate parameter in the set) to a low basic rate (say,
6 Mbps on 5 GHz and 2 or 5.5 Mbps on 2.4 GHz), but doing that cleanly
requires some more effort. For now, we can start with a simple one-liner
that forces the minimum rate to be used for EAPOL frames similarly how
the TX rate is selected for the IEEE 802.11 Management frames. This does
result in a small extra latency added to the cases where the AP would be
able to receive the higher rate, but taken into account how small number
of EAPOL frames are used, this is likely to be insignificant. A future
optimization in the minstrel_ht design can also allow this patch to be
reverted to get back to the more optimized initial TX rate.
It should also be noted that many drivers that do not use minstrel as
the rate control algorithm are already doing similar workarounds by
forcing the lowest TX rate to be used for EAPOL frames.
Cc: stable@vger.kernel.org
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
my previous patch skipped vlan range optimizations during skb size
calculations for simplicity.
This incremental patch considers vlan ranges during
skb size calculations. This leads to a bit of code duplication
in the fill and size calculation functions. But, I could not find a
prettier way to do this. will take any suggestions.
Previously, I had reused the existing br_get_link_af_size size calculation
function to calculate skb size for notifications. Reusing it this time
around creates some change in behaviour issues for the usual
.get_link_af_size callback.
This patch adds a new br_get_link_af_size_filtered() function to
base the size calculation on the incoming filter flag and include
vlan ranges.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid race conditions when using the ds->ports[] array,
we need to check if the accessed port has been initialized.
Introduce and use helper function dsa_is_port_initialized
for that purpose and use it where needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A network device notifier can be called for one or more of the created
slave devices before all slave devices have been registered. This can
result in a mismatch between ds->phys_port_mask and the registered devices
by the time the call is made, and it can result in a slave device being
added to a bridge before its entry in ds->ports[] has been initialized.
Rework the initialization code to initialize entries in ds->ports[] in
dsa_slave_create. With this change, dsa_slave_create no longer needs
to return slave_dev but can return an error code instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when TCP/SCTP port reusing happens, IPVS will find the old
entry and use it for the new one, behaving like a forced persistence.
But if you consider a cluster with a heavy load of small connections,
such reuse will happen often and may lead to a not optimal load
balancing and might prevent a new node from getting a fair load.
This patch introduces a new sysctl, conn_reuse_mode, that allows
controlling how to proceed when port reuse is detected. The default
value will allow rescheduling of new connections only if the old entry
was in TIME_WAIT state for TCP or CLOSED for SCTP.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
The IP6_TNL_TRACE macro is no longer used anywhere in the code so remove definition.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before da413eec72 ("packet: Fixed TPACKET V3 to signal poll when block is
closed rather than every packet") poll listening for an af_packet socket was
not signaled if there was no packets to process. After the patch poll is
signaled evety time when block retire timer expires. That happens because
af_packet closes the current block on timeout even if the block is empty.
Passing empty blocks to the user not only wastes CPU but also wastes ring
buffer space increasing probability of packets dropping on small timeouts.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Cc: Dan Collins <dan@dcollins.co.nz>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Guy Harris <guy@alum.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arrays (when not in a struct) "shall have a value greater than zero".
GCC complains when it's not the case here.
Fixes: ba7d49b1f0 ("rtnetlink: provide api for getting and setting slave info")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 06d961a8e2 ("mac80211/minstrel: use the new rate control API")
inverted the condition 'if (msr->sample_limit != 0)' to
'if (!msr->sample_limit != 0)'. But it is confusing both to people and
compilers (gcc5):
net/mac80211/rc80211_minstrel.c: In function 'minstrel_get_rate':
net/mac80211/rc80211_minstrel.c:376:26: warning: logical not is only applied to the left hand side of comparison
if (!msr->sample_limit != 0)
^
Let there be only 'if (!msr->sample_limit)'.
Fixes: 06d961a8e2 ("mac80211/minstrel: use the new rate control API")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Simon Horman says:
====================
Second Round of IPVS Fixes for v3.20
This patch resolves some memory leaks in connection
synchronisation code that date back to v2.6.39.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nl80211_exit should be called in cfg80211_init if nl80211_init succeeds
but regulatory_init or create_singlethread_workqueue fails.
Signed-off-by: Junjie Mao <junjie_mao@yeah.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently 8 rules in the world_regdom, but only the first 6
are applied due to an incorrect value for n_reg_rules. This causes
channels 149-165 and 60GHz to be disabled.
Signed-off-by: Jason Abele <jason@aether.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If monitor flags parsing results in active monitor but that
isn't supported, the already allocated message is leaked.
Fix this by moving the allocation after this check.
Reported-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently add nested members of the NL80211_ATTR_SCAN_FREQUENCIES
as NLA_U32 attributes of type NL80211_ATTR_WIPHY_FREQ in
cfg80211_net_detect_results. However, since there can be an arbitrary number of
frequency results, we should use the loop index of the loop used to add the
frequency results to NL80211_ATTR_SCAN_FREQUENCIES as the type (i.e. nla_type)
for each result attribute, rather than a fixed type.
This change is in line with how nested members are added to
NL80211_ATTR_SCAN_FREQUENCIES in the functions nl80211_send_wowlan_nd and
nl80211_add_scan_req.
Signed-off-by: Samuel Tan <samueltan@chromium.org>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ieee80211_vif_use_channel() fails, we have to clear
sdata->radar_required (which we might have just set).
Failing to do it results in stale radar_required field
which prevents starting new scan requests.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Eliad Peller <eliad@wizery.com>
[use false instead of 0]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes another sparse fix found by Dan Carpenter's tool.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ooZn
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-4.0-3' of git://git.linux-nfs.org/projects/anna/nfs-rdma
NFS: RDMA Client Sparse Fix#2
This patch fixes another sparse fix found by Dan Carpenter's tool.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
* tag 'nfs-rdma-for-4.0-3' of git://git.linux-nfs.org/projects/anna/nfs-rdma:
xprtrdma: Store RDMA credits in unsigned variables
Currently we don't check if the new MTU is valid or not and this allows
one to configure a smaller than minimum allowed by RFCs or even bigger
than interface own MTU, which is a problem as it may lead to packet
drops.
If you have a daemon like NetworkManager running, this may be exploited
by remote attackers by forging RA packets with an invalid MTU, possibly
leading to a DoS. (NetworkManager currently only validates for values
too small, but not for too big ones.)
The fix is just to make sure the new value is valid. That is, between
IPV6_MIN_MTU and interface's MTU.
Note that similar check is already performed at
ndisc_router_discovery(), for when kernel itself parses the RA.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit a7526eb5d0 (net: Unbreak compat_sys_{send,recv}msg), the
MSG_CMSG_COMPAT flag is blocked at the compat syscall entry points,
changing the kernel compat behaviour from the one before the commit it
was trying to fix (1be374a051, net: Block MSG_CMSG_COMPAT in
send(m)msg and recv(m)msg).
On 32-bit kernels (!CONFIG_COMPAT), MSG_CMSG_COMPAT is 0 and the native
32-bit sys_sendmsg() allows flag 0x80000000 to be set (it is ignored by
the kernel). However, on a 64-bit kernel, the compat ABI is different
with commit a7526eb5d0.
This patch changes the compat_sys_{send,recv}msg behaviour to the one
prior to commit 1be374a051.
The problem was found running 32-bit LTP (sendmsg01) binary on an arm64
kernel. Arguably, LTP should not pass 0xffffffff as flags to sendmsg()
but the general rule is not to break user ABI (even when the user
behaviour is not entirely sane).
Fixes: a7526eb5d0 (net: Unbreak compat_sys_{send,recv}msg)
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
current->state = TASK_RUNNING can be replaced by __set_current_state()
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter's static checker pointed out:
net/sunrpc/xprtrdma/rpc_rdma.c:879 rpcrdma_reply_handler()
warn: can 'credits' be negative?
"credits" is defined as an int. The credits value comes from the
server as a 32-bit unsigned integer.
A malicious or broken server can plant a large unsigned integer in
that field which would result in an underflow in the following
logic, potentially triggering a deadlock of the mount point by
blocking the client from issuing more RPC requests.
net/sunrpc/xprtrdma/rpc_rdma.c:
876 credits = be32_to_cpu(headerp->rm_credit);
877 if (credits == 0)
878 credits = 1; /* don't deadlock */
879 else if (credits > r_xprt->rx_buf.rb_max_requests)
880 credits = r_xprt->rx_buf.rb_max_requests;
881
882 cwnd = xprt->cwnd;
883 xprt->cwnd = credits << RPC_CWNDSHIFT;
884 if (xprt->cwnd > cwnd)
885 xprt_release_rqst_cong(rqst->rq_task);
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: eba8ff660b ("xprtrdma: Move credit update to RPC . . .")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
tcp_should_expand_sndbuf() does not expand the send buffer if we have
filled the congestion window.
However, it should use tcp_packets_in_flight() instead of
tp->packets_out to make this check.
Testing has established that the difference matters a lot if there are
many SACKed packets, causing a needless performance shortfall.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan add/deletes are not notified to userspace today. This patch adds
vlan info to bridge newlink/dellink notifications generated from the
bridge driver. Notifications use the RTEXT_FILTER_BRVLAN_COMPRESSED
flag to compress vlans into ranges whereever applicable.
The size calculations does not take ranges into account for
simplicity. This has the potential for allocating a larger skb than
required.
There is an existing inconsistency with bridge NEWLINK and DELLINK
change notifications. Both generate NEWLINK notifications. Since its
always a NEWLINK notification, this patch includes all vlans the port
belongs to in the notification. The NEWLINK and DELLINK request
messages however only include the vlans to be added and deleted.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to use burst capability (aka xmit_more) on a virtual device
like bonding is not supported.
For example, skb might be queued multiple times on a qdisc, with
various list corruptions.
Fixes: 38b2cf2982 ("net: pktgen: packet bursting via skb->xmit_more")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net-next commit 6d91147d18 ("batman-adv: Remove uses of return value
of seq_printf") incorrectly changed the overflow occurred return from
-1 to 1. Change it back so that the test of batadv_write_buffer_text's
return value in batadv_gw_client_seq_print_text works properly.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_vs_conn_fill_param_sync() gets in param.pe a module
reference for persistence engine from __ip_vs_pe_getbyname()
but forgets to put it. Problem occurs in backup for
sync protocol v1 (2.6.39).
Also, pe_data usually comes in sync messages for
connection templates and ip_vs_conn_new() copies
the pointer only in this case. Make sure pe_data
is not leaked if it comes unexpectedly for normal
connections. Leak can happen only if bogus messages
are sent to backup server.
Fixes: fe5e7a1efb ("IPVS: Backup, Adding Version 1 receive capability")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Although it is clear that textsearch state is intentionally passed to
skb_find_text() as uninitialized argument, it was never used by the
callers. Therefore, we can simplify skb_find_text() by making it
local variable.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have several problems in this path:
1) There is a use-after-free when removing individual elements from
the commit path.
2) We have to uninit() the data part of the element from the abort
path to avoid a chain refcount leak.
3) We have to check for set->flags to see if there's a mapping, instead
of the element flags.
4) We have to check for !(flags & NFT_SET_ELEM_INTERVAL_END) to skip
elements that are part of the interval that have no data part, so
they don't need to be uninit().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use u16 for protocol and then cast it to __be16
>> net/netfilter/nft_compat.c:140:37: sparse: incorrect type in assignment (different base types)
net/netfilter/nft_compat.c:140:37: expected restricted __be16 [usertype] ethproto
net/netfilter/nft_compat.c:140:37: got unsigned char [unsigned] [usertype] proto
>> net/netfilter/nft_compat.c:351:37: sparse: incorrect type in assignment (different base types)
net/netfilter/nft_compat.c:351:37: expected restricted __be16 [usertype] ethproto
net/netfilter/nft_compat.c:351:37: got unsigned char [unsigned] [usertype] proto
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Packets defragmentation was introduced for PACKET_FANOUT_HASH only,
see 7736d33f42 ("packet: Add pre-defragmentation support for ipv4
fanouts")
It may be useful to have defragmentation enabled regardless of
fanout type. Without that, the AF_PACKET user may have to:
1. Collect fragments from different rings
2. Defragment by itself
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"dev->ethtool_ops" and "ops" are the same, but we should use "ops"
everywhere to be consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch.pl warning "Use #include <linux/uaccess.h> instead of <asm/uaccess.h>"
Signed-off-by: Alex W Slater <alex.slater.dev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
colons are used as a separator in netdev device lookup in dev_ioctl.c
Specific functions are SIOCGIFTXQLEN SIOCETHTOOL SIOCSIFNAME
Signed-off-by: Matthew Thode <mthode@mthode.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Highlights include:
- Fix a use-after-free in decode_cb_sequence_args()
- Fix a compile error when #undef CONFIG_PROC_FS
- NFSv4.1 backchannel spinlocking issue
- Cleanups in the NFS unstable write code requested by Linus
- NFSv4.1 fix issues when the server denies our backchannel request
- Cleanups in create_session and bind_conn_to_session
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NieR
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"Highlights include:
- Fix a use-after-free in decode_cb_sequence_args()
- Fix a compile error when #undef CONFIG_PROC_FS
- NFSv4.1 backchannel spinlocking issue
- Cleanups in the NFS unstable write code requested by Linus
- NFSv4.1 fix issues when the server denies our backchannel request
- Cleanups in create_session and bind_conn_to_session"
* tag 'nfs-for-3.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Clean up bind_conn_to_session
NFSv4.1: Always set up a forward channel when binding the session
NFSv4.1: Don't set up a backchannel if the server didn't agree to do so
NFSv4.1: Clean up create_session
pnfs: Refactor the *_layout_mark_request_commit to use pnfs_layout_mark_request_commit
NFSv4: Kill unused nfs_inode->delegation_state field
NFS: struct nfs_commit_info.lock must always point to inode->i_lock
nfs: Can call nfs_clear_page_commit() instead
nfs: Provide and use helper functions for marking a page as unstable
SUNRPC: Always manipulate rpc_rqst::rq_bc_pa_list under xprt->bc_pa_lock
SUNRPC: Fix a compile error when #undef CONFIG_PROC_FS
NFSv4.1: Convert open-coded array allocation calls to kmalloc_array()
NFSv4.1: Fix a kfree() of uninitialised pointers in decode_cb_sequence_args
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains updates for your net tree, they are:
1) Fix removal of destination in IPVS when the new mixed family support
is used, from Alexey Andriyanov via Simon Horman.
2) Fix module refcount undeflow in nft_compat when reusing a match /
target.
3) Fix iptables-restore when the recent match is used with a new hitcount
that exceeds threshold, from Florian Westphal.
4) Fix stack corruption in xt_socket due to using stack storage to save
the inner IPv6 header, from Eric Dumazet.
I'll follow up soon with another batch with more fixes that are still
cooking.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cfpkt_iterate() function can return -EPROTO on error, but the
function is a u16 so the negative value gets truncated to a positive
unsigned short. This causes a static checker warning.
The only caller which might care is cffrml_receive(), when it's checking
the frame checksum. I modified cffrml_receive() so that it never says
-EPROTO is a valid checksum.
Also this isn't ever going to be inlined so I removed the "inline".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit aafb3e98b2 (netdev: introduce new NETIF_F_HW_SWITCH_OFFLOAD feature
flag for switch device offloads) add a new feature without adding it to
netdev_features_strings array; this patch fixes this.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non NAPI drivers can call skb_tstamp_tx() and then sock_queue_err_skb()
from hard IRQ context.
Therefore, sock_dequeue_err_skb() needs to block hard irq or
corruptions or hangs can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 364a9e9324 ("sock: deduplicate errqueue dequeue")
Fixes: cb820f8e4b ("net: Provide a generic socket error queue delivery method for Tx time stamps.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Open vSwitch allows moving internal vport to different namespace
while still connected to the bridge. But when namespace deleted
OVS does not detach these vports, that results in dangling
pointer to netdevice which causes kernel panic as follows.
This issue is fixed by detaching all ovs ports from the deleted
namespace at net-exit.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
IP: [<ffffffffa0aadaa5>] ovs_vport_locate+0x35/0x80 [openvswitch]
Oops: 0000 [#1] SMP
Call Trace:
[<ffffffffa0aa6391>] lookup_vport+0x21/0xd0 [openvswitch]
[<ffffffffa0aa65f9>] ovs_vport_cmd_get+0x59/0xf0 [openvswitch]
[<ffffffff8167e07c>] genl_family_rcv_msg+0x1bc/0x3e0
[<ffffffff8167e319>] genl_rcv_msg+0x79/0xc0
[<ffffffff8167d919>] netlink_rcv_skb+0xb9/0xe0
[<ffffffff8167deac>] genl_rcv+0x2c/0x40
[<ffffffff8167cffd>] netlink_unicast+0x12d/0x1c0
[<ffffffff8167d3da>] netlink_sendmsg+0x34a/0x6b0
[<ffffffff8162e140>] sock_sendmsg+0xa0/0xe0
[<ffffffff8162e5e8>] ___sys_sendmsg+0x408/0x420
[<ffffffff8162f541>] __sys_sendmsg+0x51/0x90
[<ffffffff8162f592>] SyS_sendmsg+0x12/0x20
[<ffffffff81764ee9>] system_call_fastpath+0x12/0x17
Reported-by: Assaf Muller <amuller@redhat.com>
Fixes: 46df7b81454("openvswitch: Add support for network namespaces.")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Thomas Graf <tgraf@noironetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcf_em_validate(), after calling request_module() to load the
kind-specific module, set em->ops to NULL before returning -EAGAIN, so
that module_put() is not called again by tcf_em_tree_destroy().
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a need to perform igmp join/leave operations while RTNL is
held.
Make ip_mc_{join|leave}_group() wrappers around
__ip_mc_{join|leave}_group() to avoid the proliferation of work queues.
For example, vxlan_igmp_join() could possibly be removed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_bits() returns zero on success and negative value on error,
so it is needed to invert the condition in ip_check_defrag().
Fixes: 1bf3751ec9 ("ipv4: ip_check_defrag must not modify skb before unsharing")
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is soon going to return void so remove the
return value use.
Convert the return value to test seq_has_overflowed() instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This message isn't really needed it justs waits time/space.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there's the general purpose hci_send_to_channel() API it will
do the exact same thing as queue_monitor_skb() when passed the monitor
HCI channel. This patch removes queue_monitor_skb() and replaces any
users of it with calls to hci_send_to_channel().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_send_to_control() can be made more general purpose with a small
change of passing the desired HCI channel as a parameter to it. This
allows using it for the monitor channel as well as e.g. 6lowpan in the
future.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The only reason the SMP code is essentially duplicating the
hci_copy_identity_addr() function is that the helper returns the address
type in the HCI format rather than the three-value format expected by
l2cap_chan. This patch converts the SMP code to use the helper and then
do a simple conversion from one address type to another.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull Ceph changes from Sage Weil:
"On the RBD side, there is a conversion to blk-mq from Christoph,
several long-standing bug fixes from Ilya, and some cleanup from
Rickard Strandqvist.
On the CephFS side there is a long list of fixes from Zheng, including
improved session handling, a few IO path fixes, some dcache management
correctness fixes, and several blocking while !TASK_RUNNING fixes.
The core code gets a few cleanups and Chaitanya has added support for
TCP_NODELAY (which has been used on the server side for ages but we
somehow missed on the kernel client).
There is also an update to MAINTAINERS to fix up some email addresses
and reflect that Ilya and Zheng are doing most of the maintenance for
RBD and CephFS these days. Do not be surprised to see a pull request
come from one of them in the future if I am unavailable for some
reason"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (27 commits)
MAINTAINERS: update Ceph and RBD maintainers
libceph: kfree() in put_osd() shouldn't depend on authorizer
libceph: fix double __remove_osd() problem
rbd: convert to blk-mq
ceph: return error for traceless reply race
ceph: fix dentry leaks
ceph: re-send requests when MDS enters reconnecting stage
ceph: show nocephx_require_signatures and notcp_nodelay options
libceph: tcp_nodelay support
rbd: do not treat standalone as flatten
ceph: fix atomic_open snapdir
ceph: properly mark empty directory as complete
client: include kernel version in client metadata
ceph: provide seperate {inode,file}_operations for snapdir
ceph: fix request time stamp encoding
ceph: fix reading inline data when i_size > PAGE_SIZE
ceph: avoid block operation when !TASK_RUNNING (ceph_mdsc_close_sessions)
ceph: avoid block operation when !TASK_RUNNING (ceph_get_caps)
ceph: avoid block operation when !TASK_RUNNING (ceph_mdsc_sync)
rbd: fix error paths in rbd_dev_refresh()
...
The gnet_stats_copy_app() function gets called, more often than not, with its
second argument a pointer to an automatic variable in the caller's stack.
Therefore, to avoid copying garbage afterwards when calling
gnet_stats_finish_copy(), this data is better copied to a dynamically allocated
memory that gets freed after use.
[xiyou.wangcong@gmail.com: remove a useless kfree()]
Signed-off-by: Ignacy Gawędzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
Changing the HS setting requires that SSP is enabled, however so far the
code only checked for the SSP flag but not a potentially ongoing Set SSP
operation. This patch adds a check for a pending Set SSP command in the
Set HS handler, and returns a 'busy' error if one is found.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The command handler for Set HS doesn't use mgmt_pending_add() so we can
never have a pending Set HS command that mgmt_pending_find() would
return. This patch removes an unnecessary lookup for it in the set_ssp()
handler function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
a255651d4c ("ceph: ensure auth ops are defined before use") made
kfree() in put_osd() conditional on the authorizer. A mechanical
mistake most likely - fix it.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
It turns out it's possible to get __remove_osd() called twice on the
same OSD. That doesn't sit well with rb_erase() - depending on the
shape of the tree we can get a NULL dereference, a soft lockup or
a random crash at some point in the future as we end up touching freed
memory. One scenario that I was able to reproduce is as follows:
<osd3 is idle, on the osd lru list>
<con reset - osd3>
con_fault_finish()
osd_reset()
<osdmap - osd3 down>
ceph_osdc_handle_map()
<takes map_sem>
kick_requests()
<takes request_mutex>
reset_changed_osds()
__reset_osd()
__remove_osd()
<releases request_mutex>
<releases map_sem>
<takes map_sem>
<takes request_mutex>
__kick_osd_requests()
__reset_osd()
__remove_osd() <-- !!!
A case can be made that osd refcounting is imperfect and reworking it
would be a proper resolution, but for now Sage and I decided to fix
this by adding a safe guard around __remove_osd().
Fixes: http://tracker.ceph.com/issues/8087
Cc: Sage Weil <sage@redhat.com>
Cc: stable@vger.kernel.org # 3.9+: 7c6e6fc53e: libceph: assert both regular and lingering lists in __remove_osd()
Cc: stable@vger.kernel.org # 3.9+: cc9f1f518c: libceph: change from BUG to WARN for __remove_osd() asserts
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Reviewed-by: Alex Elder <elder@linaro.org>
On Mon, Dec 22, 2014 at 5:35 PM, Sage Weil <sage@newdream.net> wrote:
> On Mon, 22 Dec 2014, Ilya Dryomov wrote:
>> Actually, pool op stuff has been unused for over two years - looks like
>> it was added for rbd create_snap and that got ripped out in 2012. It's
>> unlikely we'd ever need to manage pools or snaps from the kernel client
>> so I think it makes sense to nuke it. Sage?
>
> Yep!
Signed-off-by: Ilya Dryomov <idryomov@redhat.com>
This patch moves all the disconn_cfm callbacks to be based on the hci_cb
list. This means making l2cap_disconn_cfm private to l2cap_core.c and
sco_conn_cb private to sco.c respectively. Since the hci_conn type
filtering isn't done any more on the wrapper level the callbacks
themselves need to check that they were passed a relevant type of
connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves all the connect_cfm callbacks to be based on the hci_cb
list. This means making l2cap_connect_cfm private to l2cap_core.c and
sco_connect_cb private to sco.c respectively. Since the hci_conn type
filtering isn't done any more on the wrapper level the callbacks
themselves need to check that they were passed a relevant type of
connection.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no reason to have the custom hci_proto_auth/encrypt_cfm helpers
when the hci_cb list works equally well. This patch adds L2CAP to the
hci_cb list and makes l2cap_security_cfm a private function of
l2cap_core.c.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon need to be able to sleep inside the loops that iterate the
hci_cb list, so neither a spinlock, rwlock or rcu are usable. This patch
changes the lock to a mutex which permits sleeping while holding the
lock.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When processing hci_cb entries we want first registered callbacks to be
called first and later ones later. This is because eventually the L2CAP
callbacks that are part of the core will use this list and get
registered first. To keep the same order of calling L2CAP callbacks
before e.g. RFCOMM the order of elements needs to be this way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On top of tht is the major rework of lguest, to use PCI and virtio 1.0, to
double-check the implementation.
Then comes the inevitable fixes and cleanups from that work.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ivCe
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"OK, this has the big virtio 1.0 implementation, as specified by OASIS.
On top of tht is the major rework of lguest, to use PCI and virtio
1.0, to double-check the implementation.
Then comes the inevitable fixes and cleanups from that work"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (80 commits)
virtio: don't set VIRTIO_CONFIG_S_DRIVER_OK twice.
virtio_net: unconditionally define struct virtio_net_hdr_v1.
tools/lguest: don't use legacy definitions for net device in example launcher.
virtio: Don't expose legacy net features when VIRTIO_NET_NO_LEGACY defined.
tools/lguest: use common error macros in the example launcher.
tools/lguest: give virtqueues names for better error messages
tools/lguest: more documentation and checking of virtio 1.0 compliance.
lguest: don't look in console features to find emerg_wr.
tools/lguest: don't start devices until DRIVER_OK status set.
tools/lguest: handle indirect partway through chain.
tools/lguest: insert driver references from the 1.0 spec (4.1 Virtio Over PCI)
tools/lguest: insert device references from the 1.0 spec (4.1 Virtio Over PCI)
tools/lguest: rename virtio_pci_cfg_cap field to match spec.
tools/lguest: fix features_accepted logic in example launcher.
tools/lguest: handle device reset correctly in example launcher.
virtual: Documentation: simplify and generalize paravirt_ops.txt
lguest: remove NOTIFY call and eventfd facility.
lguest: remove NOTIFY facility from demonstration launcher.
lguest: use the PCI console device's emerg_wr for early boot messages.
lguest: always put console in PCI slot #1.
...
Merge cleanups requested by Linus.
* cleanups: (3 commits)
pnfs: Refactor the *_layout_mark_request_commit to use pnfs_layout_mark_request_commit
nfs: Can call nfs_clear_page_commit() instead
nfs: Provide and use helper functions for marking a page as unstable
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
Our UC-KLEE tool found a kernel memory leak of 512 bytes (on x86_64) for
each call to gssp_accept_sec_context_upcall()
(net/sunrpc/auth_gss/gss_rpc_upcall.c). Since it appears that this call
can be triggered by remote connections (at least, from a cursory a
glance at the call chain), it may be exploitable to cause kernel memory
exhaustion. We found the bug in kernel 3.16.3, but it appears to date
back to commit 9dfd87da1a (2013-08-20).
The gssp_accept_sec_context_upcall() function performs a pair of calls
to gssp_alloc_receive_pages() and gssp_free_receive_pages(). The first
allocates memory for arg->pages. The second then frees the pages
pointed to by the arg->pages array, but not the array itself.
Reported-by: David A. Ramos <daramos@stanford.edu>
Fixes: 9dfd87da1a ("rpc: fix huge kmalloc's in gss-proxy”)
Signed-off-by: David A. Ramos <daramos@stanford.edu>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If the phy interface mode is not found in devicetree, or if devicetree
is not configured, of_get_phy_mode returns -ENODEV. The current code
sets the phy interface mode to the return value from of_get_phy_mode
without checking if it is valid.
This invalid phy interface mode is passed as parameter to of_phy_connect
or to phy_connect_direct. This sets the phy interface mode to the invalid
value, which in turn causes problems for any code using phydev->interface.
Fixes: b31f65fb43 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some AMP controllers do not support the Read Local Features HCI commands
(even though according to the spec they should). Luckily they at least
correctly omit this from the supported commands bitmask, so we can work
around the issue by creating a second AMP init phase and issuing the HCI
command conditionally there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As soon as extract_icmp6_fields() returns, its local storage (automatic
variables) is deallocated and can be overwritten.
Lets add an additional parameter to make sure storage is valid long
enough.
While we are at it, adds some const qualifiers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: b64c9256a9 ("tproxy: added IPv6 support to the socket match")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
given:
-A INPUT -m recent --update --seconds 30 --hitcount 4
and
iptables-save > foo
then
iptables-restore < foo
will fail with:
kernel: xt_recent: hitcount (4) is larger than packets to be remembered (4) for table DEFAULT
Even when the check is fixed, the restore won't work if the hitcount is
increased to e.g. 6, since by the time checkentry runs it will find the
'old' incarnation of the table.
We can avoid this by increasing the maximum threshold silently; we only
have to rm all the current entries of the table (these entries would
not have enough room to handle the increased hitcount).
This even makes (not-very-useful)
-A INPUT -m recent --update --seconds 30 --hitcount 4
-A INPUT -m recent --update --seconds 30 --hitcount 42
work.
Fixes: abc86d0f99 (netfilter: xt_recent: relax ip_pkt_list_tot restrictions)
Tracked-down-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
On BR/EDR the L2CAP channel instances for fixed channels have so far
been marked as ready only once the L2CAP information req/rsp procedure
is complete and we have the fixed channel mask. This could however lead
to data being dropped if we receive it on the channel before knowing the
remote mask.
Since it is valid for a remote to send data this early, simply assume
that the channel is supported when we receive data on it. So far this
hasn't been noticed much because of limited use of fixed channels on
BR/EDR, but e.g. with SMP over BR/EDR this is already now visible with
automated tests failing randomly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth controllers can export extensive information about
internal states via debugfs. This patch provides an option to
choose if these information are provided or not.
For backwards compatibility with existing kernel configuration,
this option defaults to yes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Ignacy reported that when eth0 is down and add a vlan device
on top of it like:
ip link add link eth0 name eth0.1 up type vlan id 1
We will get a refcount leak:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 2
The problem is when rtnl_configure_link() fails in rtnl_newlink(),
we simply call unregister_device(), but for stacked device like vlan,
we almost do nothing when we unregister the upper device, more work
is done when we unregister the lower device, so call its ->dellink().
Reported-by: Ignacy Gawedzki <ignacy.gawedzki@green-communications.fr>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __next_ident function is a local function and so do not export it
and make it static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The a2mp_send function is a local function and so do not export it
and make it static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The amp_mgr_lookup_by_state function does not need to be exported. So
just move it to a different location and make it static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no reason to have amp_mgr_list and amp_mgr_list_lock exported
from a2mp.c and thus make both of them static.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
