Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The header file primarily used for (in-kernel) PCMCIA device drivers
also deserved a major cleanup. This header file also serves as the dumping
ground for all typedefs and definitions only used by the deprecated PCMCIA
ioctl and the deprecated PCMCIA userspace tools using this ioctl.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This ugly hack add support for Siemens MC45 PCMCIA GPRS card (which is
identical to Possio GCC, and which is offered by one of our local GPRS
providers). Card has unfortunate feature that after poweron oxcf950 chip
is fully powered and works, but attached MC45 modem is powered down :-(
There is a special sequence (which takes 1 sec :-( ) to poweron MC45 (and
after MC45 powers on, it takes more than 2 secs until firmware fully
boots...) which needs to be executed after all powerons.
I'm really not familiar with PCMCIA subsystem, so I have no idea whether I
should issue request_region() on rest of oxcf950 address range (0-7 is
UART, 8-F are special configuration registers), or how this should be
better integrated with PM system and so on - I just put it in same place
where another hack already lived...
Card uses 18.432MHz XTAL, so to get it to work you must add lines below to
the /etc/pcmcia/serial.opts.
case "$MANFID-$FUNCID-$PRODID_1-$PRODID_2-$PRODID_3-$PRODID_4" in
'030c,0003-2-GPRS-CARD--')
SERIAL_OPTS="baud_base 1152000"
;;
esac
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add new pcmcia id_table for fmvj18x_cs and serial_cs.
(TDK multi-function card (NetPartner9610 and MobileNetworker3200))
Signed-off-by: Jun Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
