It's an invalid approach to assume that among two divider values
the one nearer the exact divider is the better one.
Assume a parent rate of 1000 Hz, a divider with CLK_DIVIDER_POWER_OF_TWO
and a target rate of 89 Hz. The exact divider is ~ 11.236 so 8 and 16
are the candidates to choose from yielding rates 125 Hz and 62.5 Hz
respectivly. While 8 is nearer to 11.236 than 16 is, the latter is still
the better divider as 62.5 is nearer to 89 than 125 is.
Fixes: 774b514390 (clk: divider: Add round to closest divider)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The rate provided at the output of a clk-divider is calculated as:
DIV_ROUND_UP(parent_rate, div)
since commit b11d282dbe (clk: divider: fix rate calculation for
fractional rates). So to yield a rate not bigger than r parent_rate
must be <= r * div.
The effect of choosing a parent rate that is too big as was done before
this patch results in wrongly ruling out good dividers.
Note that this is not a complete fix as __clk_round_rate might return a
value >= its 2nd parameter. Also for dividers with
CLK_DIVIDER_ROUND_CLOSEST set the calculation is not accurate. But this
fixes the test case by Sascha Hauer that uses a chain of three dividers
under a fixed clock.
Fixes: b11d282dbe (clk: divider: fix rate calculation for fractional rates)
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
In commit c637c10355
("tipc: resolve race problem at unicast message reception") we
introduced a new mechanism for delivering buffers upwards from link
to socket layer.
That code contains a bug in how we handle the new link input queue
during failover. When a link is reset, some of its users may be blocked
because of congestion, and in order to resolve this, we add any pending
wakeup pseudo messages to the link's input queue, and deliver them to
the socket. This misses the case where the other, remaining link also
may have congested users. Currently, the owner node's reference to the
remaining link's input queue is unconditionally overwritten by the
reset link's input queue. This has the effect that wakeup events from
the remaining link may be unduely delayed (but not lost) for a
potentially long period.
We fix this by adding the pending events from the reset link to the
input queue that is currently referenced by the node, whichever one
it is.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is deleted from a net namespace the ifindex in the
corresponding entries in PF_PACKET sockets' mclists becomes stale.
This can create inconsistencies if later an interface with the same ifindex
is moved from a different namespace (not that unlikely since ifindexes are
per-namespace).
In particular we saw problems with dev->promiscuity, resulting
in "promiscuity touches roof, set promiscuity failed. promiscuity
feature of device might be broken" warnings and EOVERFLOW failures of
setsockopt(PACKET_ADD_MEMBERSHIP).
This patch deletes the mclist entries for interfaces that are deleted.
Since this now causes setsockopt(PACKET_DROP_MEMBERSHIP) to fail with
EADDRNOTAVAIL if called after the interface is deleted, also make
packet_mc_drop not fail.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJU/Wr5AAoJECte4hHFiupUFfMQAIBg9+GPuBfj60hj47FMrQ3B
93MoIMdYKhkF/cifsWb9xhdOQAMm6ET6DRoJHOxIgEW8twq6R6JFncrB42mA5b/P
kyKVon31PNh2Rdsdn+NaFcuRQSa3Tj7LHeJ53IU82c7V7/WMu3vcBEs4afv7lg+l
bH16iyDMfD3EmzKUl4ul2VqKGGdNISpx8T/y4Spml1ZUWhGAIXh6TSu+E9seZIrP
11fDysK7hRRliXEgzUWX/C6fsNzsWGN8oHFI0s1dIQ4rXPASOFcJpDtUM70+iBmF
arEJXkYD/RrC+olWS8h71Zq4uVVMj6kbUI+w8T8UL9nHA6Rv50Dlq2ZqxsPYeRNB
ZikaGpK2l9XgSxt9YaITMidUC6Q/C5TaALTun/oGZVpF6SY/8zZQKQHkbckFtbDH
ZPD7BRuUFc75wdBV2Qib/nugz1Ado43acZG/Ge0YFYpCIy6d5vtOHCXW5YCafil9
VStmKBN1Vnxnq4HcSBuEsl0qi7rv2RpUF0hEOofzoj++iMFKumjDsXpHcc4U459B
vnjb4LBqpw1ygpzEBBe8gkQa0zpb3vgNI84AKOfKy6FAZTQWXvCOT55oKys/os9G
+KJdF+PjpBVCMvtdKrD8Q0P0zYKmz+Ij57tNOaT1MoqrmpYxcrv7iSYaLrRQp3pd
z55cOGViLtHmB9lPVP5B
=B2aY
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.0-20150309' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-03-09
this is a pull request for net/master for the 4.0 release cycle, it consists of
6 patches:
A patch by Oliver Hartkopp fixes a long outstanding bug in the infrastructure,
which leads to skb_under_panics when CAN interfaces are used by AF_PACKET
sockets e.g. by dhclient. Stephane Grosjean contributes a patch for the
peak_usb driver which adds a missing initialization. Two patches by Ahmed S.
Darwish fix problems in the kvaser_usb driver. Followed by two patches by
myself, updating the MAINTAINERS file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some archs (specifically PowerPC), are sensitive with the ordering of
the enabling of the calls to function tracing and setting of the
function to use to be traced.
That is, update_ftrace_function() sets what function the ftrace_caller
trampoline should call. Some archs require this to be set before
calling ftrace_run_update_code().
Another bug was discovered, that ftrace_startup_sysctl() called
ftrace_run_update_code() directly. If the function the ftrace_caller
trampoline changes, then it will not be updated. Instead a call
to ftrace_startup_enable() should be called because it tests to see
if the callback changed since the code was disabled, and will
tell the arch to update appropriately. Most archs do not need this
notification, but PowerPC does.
The problem could be seen by the following commands:
# echo 0 > /proc/sys/kernel/ftrace_enabled
# echo function > /sys/kernel/debug/tracing/current_tracer
# echo 1 > /proc/sys/kernel/ftrace_enabled
# cat /sys/kernel/debug/tracing/trace
The trace will show that function tracing was not active.
Cc: stable@vger.kernel.org # 2.6.27+
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When ftrace is enabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_START_FUNC_RET command to ftrace_run_update_code(). Similarly, when
ftrace is disabled globally through the proc interface, we must check if
ftrace_graph_active is set. If it is set, then we should also pass the
FTRACE_STOP_FUNC_RET command to ftrace_run_update_code().
Consider the following situation.
# echo 0 > /proc/sys/kernel/ftrace_enabled
After this ftrace_enabled = 0.
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
Since ftrace_enabled = 0, ftrace_enable_ftrace_graph_caller() is never
called.
# echo 1 > /proc/sys/kernel/ftrace_enabled
Now ftrace_enabled will be set to true, but still
ftrace_enable_ftrace_graph_caller() will not be called, which is not
desired.
Further if we execute the following after this:
# echo nop > /sys/kernel/debug/tracing/current_tracer
Now since ftrace_enabled is set it will call
ftrace_disable_ftrace_graph_caller(), which causes a kernel warning on
the ARM platform.
On the ARM platform, when ftrace_enable_ftrace_graph_caller() is called,
it checks whether the old instruction is a nop or not. If it's not a nop,
then it returns an error. If it is a nop then it replaces instruction at
that address with a branch to ftrace_graph_caller.
ftrace_disable_ftrace_graph_caller() behaves just the opposite. Therefore,
if generic ftrace code ever calls either ftrace_enable_ftrace_graph_caller()
or ftrace_disable_ftrace_graph_caller() consecutively two times in a row,
then it will return an error, which will cause the generic ftrace code to
raise a warning.
Note, x86 does not have an issue with this because the architecture
specific code for ftrace_enable_ftrace_graph_caller() and
ftrace_disable_ftrace_graph_caller() does not check the previous state,
and calling either of these functions twice in a row has no ill effect.
Link: http://lkml.kernel.org/r/e4fbe64cdac0dd0e86a3bf914b0f83c0b419f146.1425666454.git.panand@redhat.com
Cc: stable@vger.kernel.org # 2.6.31+
Signed-off-by: Pratyush Anand <panand@redhat.com>
[
removed extra if (ftrace_start_up) and defined ftrace_graph_active as 0
if CONFIG_FUNCTION_GRAPH_TRACER is not set.
]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When /proc/sys/kernel/ftrace_enabled is set to zero, all function
tracing is disabled. But the records that represent the functions
still hold information about the ftrace_ops that are hooked to them.
ftrace_ops may request "REGS" (have a full set of pt_regs passed to
the callback), or "TRAMP" (the ops has its own trampoline to use).
When the record is updated to represent the state of the ops hooked
to it, it sets "REGS_EN" and/or "TRAMP_EN" to state that the callback
points to the correct trampoline (REGS has its own trampoline).
When ftrace_enabled is set to zero, all ftrace locations are a nop,
so they do not point to any trampoline. But the _EN flags are still
set. This can cause the accounting to go wrong when ftrace_enabled
is cleared and an ops that has a trampoline is registered or unregistered.
For example, the following will cause ftrace to crash:
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
# echo 0 > /proc/sys/kernel/ftrace_enabled
# echo nop > /sys/kernel/debug/tracing/current_tracer
# echo 1 > /proc/sys/kernel/ftrace_enabled
# echo function_graph > /sys/kernel/debug/tracing/current_tracer
As function_graph uses a trampoline, when ftrace_enabled is set to zero
the updates to the record are not done. When enabling function_graph
again, the record will still have the TRAMP_EN flag set, and it will
look for an op that has a trampoline other than the function_graph
ops, and fail to find one.
Cc: stable@vger.kernel.org # 3.17+
Reported-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).
Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds Marc Kleine-Budde as a co maintainer for the CAN networking
layer.
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As gitorious will shut down at the end of May 2015, the linux-can website moved
to github. This patch reflects this change.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Kvaser firmware can only read and write messages that are
not crossing the USB endpoint's wMaxPacketSize boundary. While
receiving commands from the CAN device, if the next command in
the same URB buffer crossed that max packet size boundary, the
firmware puts a zero-length placeholder command in its place
then moves the real command to the next boundary mark.
The driver did not recognize such behavior, leading to missing
a good number of rx events during a heavy rx load session.
Moreover, a tx URB context only gets freed upon receiving its
respective tx ACK event. Over time, the free tx URB contexts
pool gets depleted due to the missing ACK events. Consequently,
the netif transmission queue gets __permanently__ stopped; no
frames could be sent again except after restarting the CAN
newtwork interface.
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Upon a URB submission failure, the driver calls usb_free_urb()
but then manually frees the URB buffer by itself. Meanwhile
usb_free_urb() has alredy freed out that transfer buffer since
we're the only code path holding a reference to this URB.
Remove two of such invalid manual free().
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fixes a missing initialization of ctrlmode and ctrlmode_supported fields,
for all other CAN devices than the first one. This fix only concerns
the PCAN-USB Pro FD dual-channels CAN-FD device made by PEAK-System.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When accessing CAN network interfaces with AF_PACKET sockets e.g. by dhclient
this can lead to a skb_under_panic due to missing skb initialisations.
Add the missing initialisations at the CAN skbuff creation times on driver
level (rx path) and in the network layer (tx path).
Reported-by: Austin Schuh <austin@peloton-tech.com>
Reported-by: Daniel Steer <daniel.steer@mclaren.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The commit [63e51fd708: ALSA: hda - Don't take unresponsive D3
transition too serious] introduced a conditional fallback behavior to
the HD-audio controller depending on the flag set. However, it
introduced a silly bug, too, that the flag was evaluated in a reverse
way. This resulted in a regression of HD-audio controller driver
where it can't go to the fallback mode at communication errors.
Unfortunately (or fortunately?) this didn't come up until recently
because the affected code path is an error handling that happens only
on an unstable hardware chip. Most of recent chips work stably, thus
they didn't hit this problem. Now, we've got a regression report with
a VIA chip, and this seems indeed requiring the fallback to the
polling mode, and finally the bug was revealed.
The fix is a oneliner to remove the wrong logical NOT in the check.
(Lesson learned - be careful about double negation.)
The bug should be backported to stable, but the patch won't be
applicable to 3.13 or earlier because of the code splits. The stable
fix patches for earlier kernels will be posted later manually.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=94021
Fixes: 63e51fd708 ('ALSA: hda - Don't take unresponsive D3 transition too serious')
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When reading from the error queue, msg_name and msg_control are only
populated for some errors. A new exception for empty timestamp skbs
added a false positive on icmp errors without payload.
`traceroute -M udpconn` only displayed gateways that return payload
with the icmp error: the embedded network headers are pulled before
sock_queue_err_skb, leaving an skb with skb->len == 0 otherwise.
Fix this regression by refining when msg_name and msg_control
branches are taken. The solutions for the two fields are independent.
msg_name only makes sense for errors that configure serr->port and
serr->addr_offset. Test the first instead of skb->len. This also fixes
another issue. saddr could hold the wrong data, as serr->addr_offset
is not initialized in some code paths, pointing to the start of the
network header. It is only valid when serr->port is set (non-zero).
msg_control support differs between IPv4 and IPv6. IPv4 only honors
requests for ICMP and timestamps with SOF_TIMESTAMPING_OPT_CMSG. The
skb->len test can simply be removed, because skb->dev is also tested
and never true for empty skbs. IPv6 honors requests for all errors
aside from local errors and timestamps on empty skbs.
In both cases, make the policy more explicit by moving this logic to
a new function that decides whether to process msg_control and that
optionally prepares the necessary fields in skb->cb[]. After this
change, the IPv4 and IPv6 paths are more similar.
The last case is rxrpc. Here, simply refine to only match timestamps.
Fixes: 49ca0d8bfa ("net-timestamp: no-payload option")
Reported-by: Jan Niehusmann <jan@gondor.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
v1->v2
- fix local origin test inversion in ip6_datagram_support_cmsg
- make v4 and v6 code paths more similar by introducing analogous
ipv4_datagram_support_cmsg
- fix compile bug in rxrpc
Signed-off-by: David S. Miller <davem@davemloft.net>
On my test environment the throughput of a file transfer drops
from 4.4MBps to 116KBps due the number of repeated warning
messages. This patch removes the warning messages as DMA works
correctly with addresses using 0xC0000000 bits.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few new
device ids as well.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8Q2oACgkQMUfUDdst+ym9cgCgloBq7GqYw5lnW+zVy6fmyS3U
zHMAoMYPLjpUuO4tHfXt46NxVHIMzGsg
=TMtd
-----END PGP SIGNATURE-----
Merge tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other serial
driver bugfixes as well. Most notable is a wait_until_sent bugfix that
was traced back to being around since before 2.6.12 that Johan has fixed
up.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RCYACgkQMUfUDdst+yk62QCgycxS4giC2hyRver3dyvaNR6g
zYYAn2w0uRndW+AqP4Tls54isRz6owpF
=gA2k
-----END PGP SIGNATURE-----
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
Here are some IIO and staging driver fixes for 4.0-rc3.
Details are in the shortlog, nothing major, mostly IIO fixes for
reported issues.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RKEACgkQMUfUDdst+ylRTACeJHh8MIafzeNX1mn+YJKSvVVa
ks0AoIcvKsvIeEiWvJsNepHaHlfMs4R6
=Ppc/
-----END PGP SIGNATURE-----
Merge tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some IIO and staging driver fixes for 4.0-rc3.
Details are in the shortlog, nothing major, mostly IIO fixes for
reported issues.
All have been in linux-next successfully"
* tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel
staging: comedi: vmk80xx: remove "firmware version" kernel messages
staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample()
iio: ak8975: fix AK09911 dependencies
iio: common: ssp_sensors: Protect PM-only functions to kill warning
IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc
Revert "iio:humidity:si7020: fix pointer to i2c client"
iio: light: gp2ap020a00f: Select REGMAP_I2C
iio: light: jsa1212: Select REGMAP_I2C
iio: ad5686: fix optional reference voltage declaration
iio:adc:mcp3422 Fix incorrect scales table
iio: mxs-lradc: fix iio channel map regression
iio: imu: adis16400: Fix sign extension
staging: iio: ad2s1200: Fix sign extension
iio: mxs-lradc: only update the buffer when its conversions have finished
iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions
iio: mxs-lradc: make ADC reads not disable touchscreen interrupts
iio: mxs-lradc: separate touchscreen and buffer virtual channels
iio: imu: inv_mpu6050: Prevent dereferencing NULL
iio: iadc: wait_for_completion_timeout time in jiffies
...
Here are 2 char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RSoACgkQMUfUDdst+yk7GACgwoWKdslTxl1cib5yllhpaedl
YCYAoNGyb4C4VgdH5Lpve3j4gNRw7dy+
=1tzF
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two char/misc fixes for 4.0-rc3.
One is a reported binder driver fix needed due to a change in the mm
core that happened in 4.0-rc1. Another is a mei driver fix that
resolves a reported issue in that driver.
Both have been in linux-next for a while"
* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mei: make device disabled on stop unconditionally
android: binder: fix binder mmap failures
This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTwygoACgkQMUfUDdst+yk8ZQCdFYB9t3ZIzxiobR1pQy/PJ6Ld
dxEAnRrKzKn1FaJKCkHg35YrInKVwScZ
=tRWZ
-----END PGP SIGNATURE-----
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Final methods start with get_ready_ep(), which will fail unless we have
->state == STATE_EP_ENABLED. So they'd be failing just fine until that
first write() anyway. Let's do the following:
* get_ready_ep() gets a new argument - true when called from
ep_write_iter(), false otherwise.
* make it quiet when it finds STATE_EP_READY (no printk, that is;
the case won't be impossible after that change).
* when that new argument is true, treat STATE_EP_READY the same
way as STATE_EP_ENABLED (i.e. return zero and do not unlock).
* in ep_write_iter(), after success of get_ready_ep() turn
if (!usb_endpoint_dir_in(&epdata->desc)) {
into
if (epdata->state == STATE_EP_ENABLED &&
!usb_endpoint_dir_in(&epdata->desc)) {
- that logics only applies after config.
* have ep_config() take kernel-side buffer (i.e. use memcpy()
instead of copy_from_user() in there) and in the "let's call ep_io or
ep_aio" (again, in ep_write_iter()) add "... or ep_config() in case it's
not configured yet"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
It's unsafe to change the configurations of an activated ITS directly
since this will lead to unpredictable results. This patch guarantees
the ITSes being initialized are quiescent.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-12-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Define macros for GITS_CTLR fields to avoid using magic numbers.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-11-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When required size of Device Table is out of the page allocator's
capability, the whole ITS will fail in probing. This actually is
not the hardware's problem and is mainly a limitation of the kernel
page allocator. This patch will keep ITS going on to the next
initializaion stage with an explicit warning.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-10-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The field of page size in register GITS_BASERn might be read-only
if an implementation only supports a single, fixed page size. But
currently the ITS driver will throw out an error when PAGE_SIZE
is less than the minimum size supported by an ITS. So addressing
this problem by using 64KB pages as default granule for all the
ITS base tables.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
[maz: fixed bug breaking non Device Table allocations]
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-9-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Some kind of brain-dead implementations chooses to insert ITEes in
rapid sequence of disabled ITEes, and an un-zeroed ITT will confuse
ITS on judging whether an ITE is really enabled or not. Considering
the implementations are still supported by the GICv3 architecture,
in which ITT is not required to be zeroed before being handled to
hardware, we do the favor in ITS driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yun Wu <wuyun.wu@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
While playing with KASan support for arm64/arm the following appeared on boot:
==================================================================
BUG: AddressSanitizer: out of bounds access in __asan_load8+0x14/0x1c at addr ffffffc000ad0dc0
Read of size 8 by task swapper/0/1
page:ffffffbdc202b400 count:1 mapcount:0 mapping: (null) index:0x0
flags: 0x400(reserved)
page dumped because: kasan: bad access detected
Address belongs to variable __cpu_logical_map+0x200/0x220
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc6-next-20150129+ #481
Hardware name: FVP Base (DT)
Call trace:
[<ffffffc00008a794>] dump_backtrace+0x0/0x184
[<ffffffc00008a928>] show_stack+0x10/0x1c
[<ffffffc00075e46c>] dump_stack+0xa0/0xf8
[<ffffffc0001df490>] kasan_report_error+0x23c/0x264
[<ffffffc0001e0188>] check_memory_region+0xc0/0xe4
[<ffffffc0001dedf0>] __asan_load8+0x10/0x1c
[<ffffffc000431294>] gic_raise_softirq+0xc4/0x1b4
[<ffffffc000091fc0>] smp_send_reschedule+0x30/0x3c
[<ffffffc0000f0d1c>] try_to_wake_up+0x394/0x434
[<ffffffc0000f0de8>] wake_up_process+0x2c/0x6c
[<ffffffc0000d9570>] wake_up_worker+0x38/0x48
[<ffffffc0000dbb50>] insert_work+0xac/0xec
[<ffffffc0000dbd38>] __queue_work+0x1a8/0x374
[<ffffffc0000dbf60>] queue_work_on+0x5c/0x7c
[<ffffffc0000d8a78>] call_usermodehelper_exec+0x170/0x188
[<ffffffc0004037b8>] kobject_uevent_env+0x650/0x6bc
[<ffffffc000403830>] kobject_uevent+0xc/0x18
[<ffffffc00040292c>] kset_register+0xa8/0xc8
[<ffffffc0004d6c88>] bus_register+0x134/0x2e8
[<ffffffc0004d73b4>] subsys_virtual_register+0x2c/0x5c
[<ffffffc000a76a4c>] wq_sysfs_init+0x14/0x20
[<ffffffc000082a28>] do_one_initcall+0xa8/0x1fc
[<ffffffc000a70db4>] kernel_init_freeable+0x1ec/0x294
[<ffffffc00075aa5c>] kernel_init+0xc/0xec
Memory state around the buggy address:
ffffff80003e0820: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffff80003e0830: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffff80003e0840: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00
^
ffffff80003e0850: 00 00 fa fa fa fa fa fa 00 00 00 00 00 00 00 00
==================================================================
The reason for that cpumask_next() returns >= nr_cpu_ids if no further cpus
set, but "==" condition is checked only, so we end up with out-of-bounds
access to cpu_logical_map.
Fix is by using the condition check for cpumask_next.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When compiled with CONFIG_LOCKDEP, the kernel shouts badly, saying
that the locking in the GIC code is unsafe. I'm afraid the kernel
is right:
CPU0
----
lock(irq_controller_lock);
<Interrupt>
lock(irq_controller_lock);
*** DEADLOCK ***
This can happen while enabling, disabling, setting the type
or the affinity of an interrupt.
The fix is to take the interrupt_controller_lock with interrupts
disabled in these cases.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When compiled with CONFIG_LOCKDEP, the kernel shouts badly, saying
that my locking is unsafe. I'm afraid the kernel is right:
CPU0 CPU1
---- ----
lock(&its->lock);
local_irq_disable();
lock(&irq_desc_lock_class);
lock(&its->lock);
<Interrupt>
lock(&irq_desc_lock_class);
*** DEADLOCK ***
The fix is to always take its->lock with interrupts disabled.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The current PCI/MSI support in the GICv3 ITS doesn't really deal
with systems where different PCI devices end-up using the same
RequesterID (as it would be the case with non-transparent bridges,
for example). It is likely that none of these devices would
actually generate any interrupt, as the ITS is programmed with
the device's own ID, and not that of the bridge.
A solution to this is to iterate over the PCI hierarchy to
discover what the device aliases too. We also use this
to discover the upper bound of the number of MSIs that this
sub-hierarchy can generate.
With this in place, PCI aliases can be supported.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-4-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ITS table allocator is only allocating a single page per table.
This works fine for most things, but leads to silent lack of
interrupt delivery if we end-up with a device that has an ID that is
out of the range defined by a single page of memory. Even worse, depending
on the page size, behaviour changes, which is not a very good experience.
A solution is actually to allocate memory for the full range of ID that
the ITS supports. A massive waste memory wise, but at least a safe bet.
Tested on a Phytium SoC.
Tested-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Acked-by: Chen Baozi <chenbaozi@kylinos.com.cn>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We skip initialisation of ITS in case the device-tree has no
corresponding description, but we are still accessing to ITS bits while
setting CPU interface what leads to the kernel panic:
ITS: No ITS available, not enabling LPIs
CPU0: found redistributor 0 region 0:0x000000002f100000
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ffffffc0007fb000
[00000000] *pgd=00000000fc407003, *pud=00000000fc407003, *pmd=00000000fc408003, *pte=006000002f000707
Internal error: Oops: 96000005 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.19.0-rc2+ #318
Hardware name: FVP Base (DT)
task: ffffffc00077edb0 ti: ffffffc00076c000 task.ti: ffffffc00076c000
PC is at its_cpu_init+0x2c/0x320
LR is at gic_cpu_init+0x168/0x1bc
It happens in gic_rdists_supports_plpis() because gic_rdists is NULL.
The gic_rdists is set to non-NULL only when ITS node is presented in
the device-tree.
Fix this by moving the call to gic_rdists_supports_plpis() inside the
!list_empty(&its_nodes) block, because it is that list that guards the
validity of the rest of the information in this driver.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1425659870-11832-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On the Cortex-A9-based Armada SoCs, the MPIC is not the primary interrupt
controller. Yet, it still has to handle some per-cpu interrupt.
To do so, it is chained with the GIC using a per-cpu interrupt. However, the
current code only call irq_set_chained_handler, which is called and enable that
interrupt only on the boot CPU, which means that the parent per-CPU interrupt
is never unmasked on the secondary CPUs, preventing the per-CPU interrupt to
actually work as expected.
This was not seen until now since the only MPIC PPI users were the Marvell
timers that were not working, but not used either since the system use the ARM
TWD by default, and the ethernet controllers, that are faking there interrupts
as SPI, and don't really expect to have interrupts on the secondary cores
anyway.
Add a CPU notifier that will enable the PPI on the secondary cores when they
are brought up.
Cc: <stable@vger.kernel.org> # 3.15+
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1425378443-28822-1-git-send-email-maxime.ripard@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Apparently, the threshold for large contact area seems to be rather low on
some devices, causing the touchpad to frequently freeze during normal
usage. Because we do now know how we are supposed to use the value in
question, this commit just drops the related code completely.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These PS/2 commands make some touchpads stop responding, so this commit
adds some dummy functions to replace the generic implementation. Because
scale changes were not encapsulated in a method of struct psmouse yet, this
commit adds a method set_scale to psmouse.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We don't know whether x_max or y_max really hold the maximum possible
coordinates, and we don't know for sure whether we correctly interpret the
coordinates sent by the touchpad, so we clamp the reported values to
prevent confusion in userspace code.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The size has in most cases already been fetched from the touchpad, the
hardcoded values should have been removed.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull i2c fixes from Wolfram Sang:
"A set of updates and bugfixes for the new designware-baytrail driver.
And a documentation bugfix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: add required clocks property to binding
i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
i2c: designware-baytrail: cross-check lock functions
i2c: designware-baytrail: fix sparse warnings
i2c: designware-baytrail: fix typo in error path
i2c: designware-baytrail: describe magic numbers
Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.
Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.
Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
