smp_ops->probe() is currently supposed to return the number of cpus in
the system.
The last actual usage of the value was removed in May 2007 in e147ec8f18
"[POWERPC] Simplify smp_space_timers". We still passed the value around
until June 2010 when even that was finally removed in c1aa687d49
"powerpc: Clean up obsolete code relating to decrementer and timebase".
So drop that requirement, probe() now returns void, and update all
implementations.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The patch to add it_page_shift incorrectly changed the increment of
uaddr to use it_page_shift, rather then (1 << it_page_shift).
This broke booting on at least some Cell blades, as the iommu was
basically non-functional.
Fixes: 3a553170d3 ("powerpc/iommu: Add it_page_shift field to determine iommu page size")
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The conversion from __get_cpu_var() to this_cpu_ptr() in iic_setup_cpu()
is wrong. It causes an oops at boot.
We need the per-cpu address of struct cpu_iic, not cpu_iic.regs->prio.
Sparse noticed this, because we pass a non-iomem pointer to out_be64(),
but we obviously don't check the sparse results often enough.
Fixes: 69111bac42 ("powerpc: Replace __get_cpu_var uses")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We get way too many bug reports that say "the kernel is hung in
prom_init", which stems from the fact that the last piece of output
people see is "returning from prom_init".
The kernel is almost never hung in prom_init(), it's just that it's
crashed somewhere after prom_init() but prior to the console coming up.
The existing message should give a clue to that, ie. "returning from"
indicates that prom_init() has finished, but it doesn't seem to work.
Let's try something different.
This prints:
Quiescing Open Firmware ...
Booting Linux via __start() ...
Which hopefully makes it clear that prom_init() is not the problem, and
although __start() probably isn't either, it's at least the right place
to begin looking.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Wistfully-Acked-by: Jeremy Kerr <jk@ozlabs.org>
We have a powerpc specific global called mem_init_done which is "set on
boot once kmalloc can be called".
But that's not *quite* true. We set it at the bottom of mem_init(), and
rely on the fact that mm_init() calls kmem_cache_init() immediately
after that, and nothing is running in parallel.
So replace it with the generic and 100% correct slab_is_available().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The callers of setbat() are actually passing a pgprot_t for the flags
parameter. This doesn't matter unless STRICT_MM_TYPECHECKS is enabled.
So we can turn that on without breaking the build, change setbat() to
take a pgprot_t and have it convert it to an unsigned long internally.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The celleb code has seen no actual development for ~7 years.
We (maintainers) have no access to test hardware, and it is highly
likely the code has bit-rotted.
As far as we're aware the hardware was never widely available, and is
certainly no longer available, and no one on the list has shown any
interest in it over the years.
So remove it. If anyone has one and cares please speak up.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
The powernv code has some conditional support for running on bare metal
machines that have no OPAL firmware, but provide RTAS.
No released machines ever supported that, and even in the lab it was
just a transitional hack in the days when OPAL was still being
developed.
So remove the code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Freescale updates from Scott:
"Highlights include BMan device tree nodes, an MSI erratum workaround, a
couple minor performance improvements, config updates, and misc
fixes/cleanup."
By default we enable CONFIG_I2C_MUX and CONFIG_I2C_MUX_PCA954x,
which are needed on T2080QDS, T4240QDS, B4860QDS, etc.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[scottwood@freescale.com: fixed subject line]
Signed-off-by: Scott Wood <scottwood@freescale.com>
After previous discussions regarding the subject [1][2], there's no clear
explanation or reason why the call was needed in the first place. The sensible
argument is some sort of synchronization between the CPU and the MPIC, which
hasn't been pointed out precisely and is no longer required (at least on BookE
platforms).
The benefit of this change is saving a MMIO trap per interrupt when running in a
KVM guest.
[1] https://patchwork.ozlabs.org/patch/429098/
[2] https://patchwork.ozlabs.org/patch/433557/
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The k(un)map function may be called in atomic context in the
function map_and_flush(), so use k(un)map_atomic to replace it,
else we would get the below warning during kdump:
BUG: sleeping function called from invalid context at include/linux/highmem.h:58
in_atomic(): 1, irqs_disabled(): 1, pid: 736, name: sh
INFO: lockdep is turned off.
irq event stamp: 0
hardirqs last enabled at (0): [< (null)>] (null)
hardirqs last disabled at (0): [<c000000000066d1c>] .copy_process.part.44+0x50c/0x1360
softirqs last enabled at (0): [<c000000000066d1c>] .copy_process.part.44+0x50c/0x1360
softirqs last disabled at (0): [< (null)>] (null)
CPU: 1 PID: 736 Comm: sh Tainted: G D W 3.10.62-ltsi-WR6.0.0.0_standard #2
Call Trace:
[c0000000f47cf120] [c00000000000b150] .show_stack+0x170/0x290 (unreliable)
[c0000000f47cf210] [c000000000b71334] .dump_stack+0x28/0x3c
[c0000000f47cf280] [c0000000000bb5d8] .__might_sleep+0x1a8/0x270
[c0000000f47cf310] [c0000000000440cc] .map_and_flush+0x4c/0xc0
[c0000000f47cf390] [c0000000000441cc] .mpc85xx_smp_machine_kexec+0x8c/0xec0
[c0000000f47cf420] [c00000000002ae00] .machine_kexec+0x60/0x90
[c0000000f47cf4b0] [c00000000010957c] .crash_kexec+0x8c/0x100
[c0000000f47cf6a0] [c000000000015df8] .die+0x348/0x450
[c0000000f47cf740] [c00000000002f3a0] .bad_page_fault+0xe0/0x130
[c0000000f47cf7c0] [c00000000001f3e4] storage_fault_common+0x40/0x44
Signed-off-by: Yanjiang Jin <yanjiang.jin@windriver.com>
[scottwood@freescale.com: fix subject line]
Signed-off-by: Scott Wood <scottwood@freescale.com>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL;
@@
-EXPORT_SYMBOL(f);
// </smpl>
Furthermore, the function is never used, so its definition is dropped as
well.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Scott Wood <scottwood@freescale.com>
All the cache line size of the current book3e 64bit SoCs are 64 bytes.
So we should use this size to align the member of paca_struct.
This only change the paca_struct's members which are private to book3e
CPUs, and should not have any effect to book3s ones. With this, we save
192 bytes. Also change it to __aligned(size) since it is preferred over
__attribute__((aligned(size))).
Before:
/* size: 1920, cachelines: 30, members: 46 */
/* sum members: 1667, holes: 6, sum holes: 141 */
/* padding: 112 */
After:
/* size: 1728, cachelines: 27, members: 46 */
/* sum members: 1667, holes: 4, sum holes: 13 */
/* padding: 48 */
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch fixes a section mismatch warning
WARNING: vmlinux.o(.text+0x213b6): Section mismatch in reference from the function chrp_init_early() to the variable .init.data:boot_command_line
The function chrp_init_early() references
the variable __initdata boot_command_line.
This is often because chrp_init_early lacks a __initdata
annotation or the annotation of boot_command_line is wrong.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, when a sensor value is read, the kernel calls OPAL, which in
turn builds a message for the FSP, and waits for a message back.
The new device tree for OPAL sensors [1] adds new sensors that can be
read synchronously (core temperatures for instance) and that don't need
to wait for a response.
This patch modifies the opal call to accept an OPAL_SUCCESS return value
and cover the case above.
[1] https://lists.ozlabs.org/pipermail/skiboot/2015-March/000639.html
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OPAL has its own list of return codes. The patch provides a translation
of such codes in errnos for the opal_sensor_read call, and possibly
others if needed.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use the normal return values for bool functions
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If M64 has been supported, the prefetchable 64-bits memory resources
shouldn't be mapped to the corresponding PE# via M32DT. Unfortunately,
we're doing that in pnv_ioda_setup_pe_seg() wrongly. The issue was
introduced by commit 262af55 ("powerpc/powernv: Enable M64 aperatus
for PHB3"). The patch fixes the issue by simply skipping M64 resources
when updating to M32DT.
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The function eeh_add_parent_pe() is used to create a PE or add one
edev to its parent PE. Current code checks if PE#0 is valid for the
later case. Actually, we should validate PE#0 for both cases when
EEH core regards PE#0 as invalid one (without flag EEH_VALID_PE_ZERO).
Otherwise, not all EEH devices can be added to its parent PE#0 for
EEH on P7IOC.
The patch fixes the issue by validating PE#0 for the two cases. So far,
we don't have PE#0 for EEH on P7IOC, but it will show up when we enable
M64 for P7IOC. The patch also makes the error message more meaningful.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds a test of the switch_endian() syscall we added in the previous
commit.
We test it by calling the endian switch syscall, and then executing some
code in the other endian to check everything went as expected. That code
checks registers we expect to be maintained are. If the endian switch
failed to happen that code sequence will be illegal and cause the test
to abort.
We then switch back to the original endian, do the same checks and
finally write a success message and exit(0).
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently have a "special" syscall for switching endianness. This is
syscall number 0x1ebe, which is handled explicitly in the 64-bit syscall
exception entry.
That has a few problems, firstly the syscall number is outside of the
usual range, which confuses various tools. For example strace doesn't
recognise the syscall at all.
Secondly it's handled explicitly as a special case in the syscall
exception entry, which is complicated enough without it.
As a first step toward removing the special syscall, we need to add a
regular syscall that implements the same functionality.
The logic is simple, it simply toggles the MSR_LE bit in the userspace
MSR. This is the same as the special syscall, with the caveat that the
special syscall clobbers fewer registers.
This version clobbers r9-r12, XER, CTR, and CR0-1,5-7.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
During suspend/migration operation we must wait for the VASI state reported
by the hypervisor to become Suspending prior to making the ibm,suspend-me
RTAS call. Calling routines to rtas_ibm_supend_me() pass a vasi_state variable
that exposes the VASI state to the caller. This is unnecessary as the caller
only really cares about the following three conditions; if there is an error
we should bailout, success indicating we have suspended and woken back up so
proceed to device tree update, or we are not suspendable yet so try calling
rtas_ibm_suspend_me again shortly.
This patch removes the extraneous vasi_state variable and simply uses the
return code to communicate how to proceed. We either succeed, fail, or get
-EAGAIN in which case we sleep for a second before trying to call
rtas_ibm_suspend_me again. The behaviour of ppc_rtas() remains the same,
but migrate_store() now returns the propogated error code on failure.
Previously -1 was returned from migrate_store() in the failure case which
equates to -EPERM and was clearly wrong.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Cc: Nathan Fontenont <nfont@linux.vnet.ibm.com>
Cc: Cyril Bur <cyrilbur@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Fix the attribute name of the configuration record class ID.
Signed-off-by: Philippe Bergheaud <felix@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We currently read the information about idle states from the device
tree, so as to find out the CPU idle states supported by the platform.
Use the of_property_read/count_xxx() APIs, which handle endian
conversions for us, and mean we don't need any endian annotations in the
code.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
kmem_cache_create()->kmem_cache_create_memcg()->kstrdup() allocates new
space and copys name's content, so it is safe to free name memory after
calling kmem_cache_create(). Else kmemleak will report the below
warning:
unreferenced object 0xc0000000f9002160 (size 16):
comm "swapper/0", pid 0, jiffies 4294892296 (age 1386.640s)
hex dump (first 16 bytes):
70 67 74 61 62 6c 65 2d 32 5e 39 00 de ad be ef pgtable-2^9.....
backtrace:
[<c0000000004e03ec>] .kvasprintf+0x5c/0xa0
[<c0000000004e045c>] .kasprintf+0x2c/0x50
[<c00000000002e36c>] .pgtable_cache_add+0xac/0x100
[<c00000000002e3e4>] .pgtable_cache_init+0x24/0x80
[<c000000000c6c67c>] .start_kernel+0x228/0x4c8
[<c000000000000594>] .start_here_common+0x24/0x90
Signed-off-by: Yanjiang Jin <yanjiang.jin@windriver.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Provide an unregister interface for the opal message notifiers
to be called when not needed like during driver unload/remove.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes the condition check of incoming message type which can
otherwise shoot beyond the message notifiers head array.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Reviewed-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use helper functions to access current->state.
Direct assignments are prone to races and therefore buggy.
current->state = TASK_RUNNING can be replaced by __set_current_state()
Thanks to Peter Zijlstra for the exact definition of the problem.
Suggested-By: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If CONFIG_SMP=n, <linux/smp.h> does not include <asm/smp.h>, causing:
drivers/cpufreq/ppc-corenet-cpufreq.c: In function 'corenet_cpufreq_cpu_init':
drivers/cpufreq/ppc-corenet-cpufreq.c:173:3: error: implicit declaration of function 'get_hard_smp_processor_id' [-Werror=implicit-funcuresh E. Warrier" <warrier@linux.vnet.ibm.com>
X-Patchwork-Id: 443703
Message-Id: <54EE5989.7010800@linux.vnet.ibm.com>
To: linuxppc-dev@ozlabs.org
Date: Wed, 25 Feb 2015 17:23:53 -0600
Export __spin_yield so that the arch_spin_unlock() function can
be invoked from a module. This will be required for modules where
we want to take a lock that is also is acquired in hypervisor
real mode. Because we want to avoid running any lockdep code
(which may not be safe in real mode), this lock needs to be
an arch_spinlock_t instead of a normal spinlock.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Internally, of_find_node_by_name() calls of_node_put() on its "from"
parameter, which must not be done on "master", as it's still in use, and
will be released manually later. This may cause a zero kref refcount.
Call of_node_get() before to compensate for this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If OPAL requests it, call it back via opal_poll_events() at a
regular interval. Some versions of OPAL on some machines require
this to operate some internal timeouts properly.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Present code checks for update_flash_data in opal_flash_term_callback().
update_flash_data has been statically initialized to zero, and that
is the value of FLASH_IMG_READY. Also code update initialization happens
during subsys init.
So if reboot is issued before the subsys init stage then we endup displaying
"Flashing new firmware" message.. which may confuse end user.
This patch fixes above described issue by initializes update_flash status
to invalid state.
Reported-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc specific st_le*() and ld_le*() functions in
arch/powerpc/asm/swab.h no longer have any users. They are also
misleadingly named, since they always byteswap, even on a little-endian
host.
This patch removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Sometimes the KVM code on powerpc needs to emulate load or store
instructions from the guest, which can include both normal and byte
reversed forms.
We currently (AFAICT) handle this correctly, but some variable names are
very misleading. In particular we use "is_bigendian" in several places to
actually mean "is the IO the same endian as the host", but we now support
little-endian powerpc hosts. This also ties into the misleadingly named
ld_le*() and st_le*() functions, which in fact always byteswap, even on
an LE host.
This patch cleans this up by renaming to more accurate "host_swabbed", and
uses the generic swab*() functions instead of the powerpc specific and
misleadingly named ld_le*() and st_le*() functions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When the MXC MMUC driver is used on a Freescale MPC512x machine, it
contains some additional byteswapping code (I'm assuming this is a
workaround for a hardware defect). This uses the ppc specific st_le32()
function, but there's no reason not to use the generic swab32() function
instead. gcc is capable of generating the efficient ppc byte-reversing
load/store instructions without the arch-specific helper.
This patch, therefore, switches to the generic byteswap routine.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc arch code enables PCI_COMMAND_MEMORY (and has done so for
more than 10 years at least !) on pci_enable_device() and the hackery
on the MMIO accessor is useless as well, our writel does everything
this driver should need.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch removes struct eeh_dev::dn and the corresponding helper
functions: eeh_dev_to_of_node() and of_node_to_eeh_dev(). Instead,
eeh_dev_to_pdn() and pdn_to_eeh_dev() should be used to get the
pdn, which might contain device_node on PowerNV platform.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There are 3 EEH operations whose arguments contain device_node:
read_config(), write_config() and restore_config(). The patch
replaces device_node with pci_dn.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Originally, EEH core probes on device_node or pci_dev to populate
EEH devices and PEs, which conflicts with the fact: SRIOV VFs are
usually enabled and created by PF's driver and they don't have the
corresponding device_nodes. Instead, SRIOV VFs have dynamically
created pci_dn, which can be used for EEH probe.
The patch reworks EEH probe for PowerNV and pSeries platforms to
do probing based on pci_dn, instead of pci_dev or device_node any
more.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
