This patch adds support for build-in watchdog device found on
Freescale imx31 and imx35 SoCs.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Power Gates must to be always enabled.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the using of Bad Block Table is not constantly a good behave
I had made it configurable.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to imx31 reference manual the signal from external low
frequency clock is sent to RTC clock.
The patch makes redundant the previously defined mxc_rtc clock.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
serial: sh-sci: remove duplicated #include
sh: Export uncached helper symbols.
sh: Fix up NUMA build for 29-bit.
serial: sh-sci: Fix build failure for non-sh architectures.
sh: Fix up uncached offset for legacy 29-bit mode.
sh: Support CPU affinity masks for INTC controllers.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: fix compile errors in dma-mapping-common.h
alpha: remove trailing spaces in messages
alpha: use __ratelimit
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Remove IOMMU_VMERGE config option
powerpc: Fix swiotlb to respect the boot option
powerpc: Do not call prink when CONFIG_PRINTK is not defined
powerpc: Use correct ccr bit for syscall error status
powerpc/fsl-booke: Get coherent bit from PTE
powerpc/85xx: Make sure lwarx hint isn't set on ppc32
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty_port,usb-console: Fix usb serial console open/close regression
tty: cpm_uart: use resource_size()
tty_buffer: Fix distinct type warning
hvc_console: Fix race between hvc_close and hvc_remove
uartlite: Fix build on sparc.
tty: Take a 256 byte padding into account when buffering below sub-page units
Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
driver core: numa: fix BUILD_BUG_ON for node_read_distance
driver-core: document ERR_PTR() return values
kobject: documentation: Update to refer to kset-example.c.
sysdev: the cpu probe/release attributes should be sysdev_class_attributes
kobject: documentation: Fix erroneous example in kobject doc.
driver-core: fix missing kernel-doc in firmware_class
Driver core: Early platform kernel-doc update
sysfs: fix sysfs lockdep warning in mlx4 code
sysfs: fix sysfs lockdep warning in infiniband code
sysfs: fix sysfs lockdep warning in ipmi code
sysfs: Initialised pci bus legacy_mem field before use
sysfs: use sysfs_bin_attr_init in firmware class driver
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (45 commits)
USB: gadget/multi: cdc_do_config: remove redundant check
usb: r8a66597-hcd: fix removed from an attached hub
USB: xhci: Make endpoint interval debugging clearer.
USB: Fix usb_fill_int_urb for SuperSpeed devices
USB: cp210x: Remove double usb_control_msg from cp210x_set_config
USB: Remove last bit of CONFIG_USB_BERRY_CHARGE
USB: gadget: add gadget controller number for s3c-hsotg driver
USB: ftdi_sio: Fix locking for change_speed() function
USB: g_mass_storage: fixed module name in Kconfig
USB: gadget: f_mass_storage::fsg_bind(): fix error handling
USB: g_mass_storage: fix section mismatch warnings
USB: gadget: fix Blackfin builds after gadget cleansing
USB: goku_udc: remove potential null dereference
USB: option.c: Add Pirelli VID/PID and indicate Pirelli's modem interface is 0xff
USB: serial: Fix module name typo for qcaux Kconfig entry.
usb: cdc-wdm: Fix deadlock between write and resume
usb: cdc-wdm: Fix order in disconnect and fix locking
usb: cdc-wdm:Fix loss of data due to autosuspend
usb: cdc-wdm: Fix submission of URB after suspension
usb: cdc-wdm: Fix race between disconnect and debug messages
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (205 commits)
ceph: update for write_inode API change
ceph: reset osd after relevant messages timed out
ceph: fix flush_dirty_caps race with caps migration
ceph: include migrating caps in issued set
ceph: fix osdmap decoding when pools include (removed) snaps
ceph: return EBADF if waiting for caps on closed file
ceph: set osd request message front length correctly
ceph: reset front len on return to msgpool; BUG on mismatched front iov
ceph: fix snaptrace decoding on cap migration between mds
ceph: use single osd op reply msg
ceph: reset bits on connection close
ceph: remove bogus mds forward warning
ceph: remove fragile __map_osds optimization
ceph: fix connection fault STANDBY check
ceph: invalidate_authorizer without con->mutex held
ceph: don't clobber write return value when using O_SYNC
ceph: fix client_request_forward decoding
ceph: drop messages on unregistered mds sessions; cleanup
ceph: fix comments, locking in destroy_inode
ceph: move dereference after NULL test
...
Fix trivial conflicts in Documentation/ioctl/ioctl-number.txt
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: trivial white space
[CIFS] checkpatch cleanup
cifs: add cifs_revalidate_file
cifs: add a CIFSSMBUnixQFileInfo function
cifs: add a CIFSSMBQFileInfo function
cifs: overhaul cifs_revalidate and rename to cifs_revalidate_dentry
cdc_do_config() had a double ret check after fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the problem that when a USB hub is attached to the r8a66597-hcd and
a device is removed from that hub, it's likely that a kernel panic follows.
Reported-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xHCI hardware can only handle polling intervals that are a power of
two. When we add a new endpoint during a bandwidth allocation, and the
polling interval is rounded down to a power of two, print the original
polling interval in the endpoint descriptor.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB 3 and Wireless USB specify a logarithmic encoding of the endpoint
interval that matches the USB 2 specification. usb_fill_int_urb() didn't
know that and was filling in the interval as if it was USB 1.1. Fix
usb_fill_int_urb() for SuperSpeed devices, but leave the wireless case
alone, because David Vrabel wants to keep the old encoding.
Update the struct urb kernel doc to note that SuperSpeed URBs must have
urb->interval specified in microframes.
Add a missing break statement in the usb_submit_urb() interrupt URB
checking, since wireless USB and SuperSpeed USB encode urb->interval
differently. This allows xHCI roothubs to actually register with khubd.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes a double usb_control_msg that sets the cp210x
configuration registers a second time when calling cp210x_set_config.
For data sizes >2 the second write gets corrupted.
The patch has been created against 2.6.34-rc1, but all cp210x driver
revisions are affected.
Signed-off-by: Michael Brunner <mibru@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
One last bit was missed while removing the USB_BERRY_CHARGE config
option in a8d4211f33 which gets dropped
by this patch.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This prevents some drivers from complaining that no bcdDevice id was set.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The change_speed() function should be serialized against multiple calls.
Use the cfg_lock mutex to do this.
Signed-off-by: Alessio Igor Bogani <abogani@texware.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kconfig help message for Mass Storage Gadget claimed the
module will be named "g_file_storage" whereas it should be
"g_mass_storage".
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Contrary to the comment in fsg_add, fsg_bind calls fsg_unbind on errors,
which decreases refcount and frees the fsg_dev structure, causing trouble
when fsg_add does the same.
Fix it by simply leaving up cleanup to fsg_add().
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit (0e530b4578) that moved usb_ep_autoconfig from the
__devinit section to the __init section missed the mass storage device.
Its fsg_bind() function uses the usb_ep_autoconfig() function from non
__init context leading to:
WARNING: drivers/usb/gadget/g_mass_storage.o(.text): Section mismatch in
reference from the function _fsg_bind()
to the function .init.text:_usb_ep_autoconfig()
So move fsg_bind() into __init as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent change to clean out dead gadget drivers (90f7976880)
missed the call to gadget_is_musbhsfc() behind CONFIG_BLACKFIN. This
causes Blackfin gadget builds to fail since the function no longer
exists anywhere.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"dev" is always null here. In the end it's only used to get the
pci_name() of "pdev" which is redundant information and so I
removed it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The module is called qcaux and not moto_modem. Also use help instead of
---help-- to be in sync with the other Kconfig entries.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new runtime PM scheme allows resume() to have no locks.
This fixes the deadlock.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- as the callback can schedule work, URBs must be killed first
- if the driver causes an autoresume, the caller must handle locking
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The guarding flag must be set and tested under spinlock
and cleared before the URBs are resubmitted in resume.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's a window under which cdc-wdm may submit
an URB to a device about to be suspended. This
introduces a flag to prevent it.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_dbg() and dev_err() cannot be used to report failures
that may have been caused by a device's removal
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While an available response is read the device must not
be autosuspended. This requires a flag dedicated to that
purpose.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unify mutexes to fix a race between write and disconnect
and shift the test for disconnection to always report it.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
... and avoid a compilation if we disable host side
of musb.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The recent commit "usb: musb: Add context save and restore support" added
some stubs for the Blackfin code so things would compile, but it also
added a bunch of warnings due to missing return statements.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB PHY on current Blackfin processors is a UTMI+ level 2 PHY.
However, it has no ULPI support - so there are no registers at all.
That means accesses to ULPI_BUSCONTROL have to be abstracted away
like other MUSB registers.
This fixes building for Blackfin parts again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONFIG_ARCH_OMAP34XX is now CONFIG_ARCH_OMAP3.
But since drivers/usb/musb/omap2430.c use CONFIG_PM for these
registers and functions, do the same for the header.
Otherwise we get the following for most omap3 defconfigs:
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:261: error: expected identifier or '(' before 'while'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'do'
drivers/usb/musb/omap2430.c:268: error: expected identifier or '(' before 'while'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
C file uses IS_ERR and PTR_ERR, but doesn't include <linux/err.h>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name used in the documentation doesn't match reality.
Signed-off-by: Oliver Neukum <neukum@b1-systems.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
