Use dma_pool_zalloc instead of using dma_pool_alloc to allocate
memory and then zeroing it with memset 0.
This simplifies the code.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Each of the operations in ccp_run_cmd() needs several hundred
bytes of kernel stack. Depending on the inlining, these may
need separate stack slots that add up to more than the warning
limit, as shown in this clang based build:
drivers/crypto/ccp/ccp-ops.c:871:12: error: stack frame size of 1164 bytes in function 'ccp_run_aes_cmd' [-Werror,-Wframe-larger-than=]
static int ccp_run_aes_cmd(struct ccp_cmd_queue *cmd_q, struct ccp_cmd *cmd)
The problem may also happen when there is no warning, e.g. in the
ccp_run_cmd()->ccp_run_aes_cmd()->ccp_run_aes_gcm_cmd() call chain with
over 2000 bytes.
Mark each individual function as 'noinline_for_stack' to prevent
this from happening, and move the calls to the two special cases for aes
into the top-level function. This will keep the actual combined stack
usage to the mimimum: 828 bytes for ccp_run_aes_gcm_cmd() and
at most 524 bytes for each of the other cases.
Fixes: 63b945091a ("crypto: ccp - CCP device driver and interface support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Redefine pr_fmt so that the module name is prefixed to every
log message produced by the ccp-crypto module
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP driver is able to act as a DMA engine. Add a module parameter that
allows this feature to be enabled/disabled.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Provide the ability to constrain the total number of enabled devices in
the system. Once max_devs devices have been configured, subsequently
probed devices are ignored.
The max_devs parameter may be zero, in which case all CCPs are disabled.
PSPs are always enabled and active.
Disabling the CCPs also disables DMA and RNG registration.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a module parameter to limit the number of queues per CCP. The default
value (nqueues=0) is to set up every available queue on each device.
The count of queues starts from the first one found on the device (which
varies based on the device ID).
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a config option to exclude DebugFS support in the CCP driver.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the AES library instead of the cipher interface to perform
the single block of AES processing involved in updating the key
of the cmac(aes) hash.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto fixes from Herbert Xu:
- Fix missed wake-up race in padata
- Use crypto_memneq in ccp
- Fix version check in ccp
- Fix fuzz test failure in ccp
- Fix potential double free in crypto4xx
- Fix compile warning in stm32
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
padata: use smp_mb in padata_reorder to avoid orphaned padata jobs
crypto: ccp - Fix SEV_VERSION_GREATER_OR_EQUAL
crypto: ccp/gcm - use const time tag comparison.
crypto: ccp - memset structure fields to zero before reuse
crypto: crypto4xx - fix a potential double free in ppc4xx_trng_probe
crypto: stm32/hash - Fix incorrect printk modifier for size_t
SEV_VERSION_GREATER_OR_EQUAL() will fail if upgrading from 2.2 to 3.1, for
example, because the minor version is not equal to or greater than the
major.
Fix this and move to a static inline function for appropriate type
checking.
Fixes: edd303ff0e ("crypto: ccp - Add DOWNLOAD_FIRMWARE SEV command")
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Avoid leaking GCM tag through timing side channel.
Fixes: 36cf515b9b ("crypto: ccp - Enable support for AES GCM on v5 CCPs")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Cfir Cohen <cfir@google.com>
Acked-by: Gary R Hook <ghook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The AES GCM function reuses an 'op' data structure, which members
contain values that must be cleared for each (re)use.
This fix resolves a crypto self-test failure:
alg: aead: gcm-aes-ccp encryption test failed (wrong result) on test vector 2, cfg="two even aligned splits"
Fixes: 36cf515b9b ("crypto: ccp - Enable support for AES GCM on v5 CCPs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
Add an SPDX identifier and remove any specific statements.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The error code read from the queue status register is only 6 bits wide,
but we need to verify its value is within range before indexing the error
messages.
Fixes: 81422badb3 ("crypto: ccp - Make syslog errors human-readable")
Cc: <stable@vger.kernel.org>
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Crypto self-tests reveal an error:
alg: skcipher: cbc-des3-ccp encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
The offset value should not be recomputed when retrieving the context.
Also, a code path exists which makes decisions based on older (version 3)
hardware; a v3 device deosn't support 3DES so remove this check.
Fixes: 990672d485 ('crypto: ccp - Enable 3DES function on v5 CCPs')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Updated testmgr will exhibit this error message when loading the
ccp-crypto module:
alg: skcipher: cfb-aes-ccp encryption failed with err -22 on test vector 3, cfg="in-place"
Update the CCP crypto driver to correctly treat CFB as a streaming mode
cipher (instead of block mode). Update the configuration for CFB to
specify the block size as a single byte;
Fixes: 2b789435d7 ('crypto: ccp - CCP AES crypto API support')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CFB mode should be treated as a stream cipher, not block.
Fixes: 63b945091a ('crypto: ccp - CCP device driver and interface support')
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flags field in 'struct shash_desc' never actually does anything.
The only ostensibly supported flag is CRYPTO_TFM_REQ_MAY_SLEEP.
However, no shash algorithm ever sleeps, making this flag a no-op.
With this being the case, inevitably some users who can't sleep wrongly
pass MAY_SLEEP. These would all need to be fixed if any shash algorithm
actually started sleeping. For example, the shash_ahash_*() functions,
which wrap a shash algorithm with the ahash API, pass through MAY_SLEEP
from the ahash API to the shash API. However, the shash functions are
called under kmap_atomic(), so actually they're assumed to never sleep.
Even if it turns out that some users do need preemption points while
hashing large buffers, we could easily provide a helper function
crypto_shash_update_large() which divides the data into smaller chunks
and calls crypto_shash_update() and cond_resched() for each chunk. It's
not necessary to have a flag in 'struct shash_desc', nor is it necessary
to make individual shash algorithms aware of this at all.
Therefore, remove shash_desc::flags, and document that the
crypto_shash_*() functions can be called from any context.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation for new akcipher verify call remove sign/verify callbacks
from RSA backends and make PKCS1 driver call encrypt/decrypt instead.
This also complies with the well-known idea that raw RSA should never be
used for sign/verify. It only should be used with proper padding scheme
such as PKCS1 driver provides.
Cc: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Cc: qat-linux@intel.com
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Horia Geantă <horia.geanta@nxp.com>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Signed-off-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, we free the psp_master if the PLATFORM_INIT fails during the
SEV FW probe. If psp_master is freed then driver does not invoke the PSP
FW. As per SEV FW spec, there are several commands (PLATFORM_RESET,
PLATFORM_STATUS, GET_ID etc) which can be executed in the UNINIT state
We should not free the psp_master when PLATFORM_INIT fails.
Fixes: 200664d523 ("crypto: ccp: Add SEV support")
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: stable@vger.kernel.org # 4.19.y
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use kmemdup rather than duplicating its implementation
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current definition and implementation of the SEV_GET_ID command
does not provide the length of the unique ID returned by the firmware.
As per the firmware specification, the firmware may return an ID
length that is not restricted to 64 bytes as assumed by the SEV_GET_ID
command.
Introduce the SEV_GET_ID2 command to overcome with the SEV_GET_ID
limitations. Deprecate the SEV_GET_ID in the favor of SEV_GET_ID2.
At the same time update SEV API web link.
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Nathaniel McCallum <npmccallum@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix sparse warning:
drivers/crypto/ccp/ccp-crypto-rsa.c:251:5:
warning: symbol 'ccp_register_rsa_alg' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
The current content of some of the driver messages and the way that they
are issued results in some confusion, especially in the area of the PSP
as it relates to SEV support. If SEV is not supported, a message is issued
that says "psp initialization failed." This makes it seem like there was
a problem, when in fact, the PSP support is just disabled if SEV is not
supported.
Update the driver to check SEV support a bit earlier and issue a debug-
level message if SEV is not supported, followed by a debug-level message
that the PSP is disabled. This way you will only see PSP messages if SEV
is supported or if debug information is desired. Also, remove the overall
"enabled" and "disabled" messages for the driver and rely on the CCP and
PSP support to issue component-specific messages.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A kexec reboot may leave the firmware in INIT or WORKING state.
Currently, we issue PLATFORM_INIT command during the probe without
checking the current state. The PLATFORM_INIT command fails if the
FW is already in INIT state. Lets check the current state, if FW
is not in UNINIT state then transition it to UNINIT before
initializing or upgrading the FW.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary Hook <gary.hook@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CRYPTO_TFM_REQ_WEAK_KEY confuses newcomers to the crypto API because it
sounds like it is requesting a weak key. Actually, it is requesting
that weak keys be forbidden (for algorithms that have the notion of
"weak keys"; currently only DES and XTS do).
Also it is only one letter away from CRYPTO_TFM_RES_WEAK_KEY, with which
it can be easily confused. (This in fact happened in the UX500 driver,
though just in some debugging messages.)
Therefore, make the intent clear by renaming it to
CRYPTO_TFM_REQ_FORBID_WEAK_KEYS.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Correct copyright dates for files that have had code added
to them in 2018.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'cipher' algorithms (single block ciphers) are always synchronous, so
passing CRYPTO_ALG_ASYNC in the mask to crypto_alloc_cipher() has no
effect. Many users therefore already don't pass it, but some still do.
This inconsistency can cause confusion, especially since the way the
'mask' argument works is somewhat counterintuitive.
Thus, just remove the unneeded CRYPTO_ALG_ASYNC flags.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fixes the following sparse warning:
drivers/crypto/ccp/psp-dev.c:444:5: warning:
symbol 'sev_get_firmware' was not declared. Should it be static?
Fixes: e93720606e ("crypto: ccp - Allow SEV firmware to be chosen based on Family and Model")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clang emits a warning about this construct:
drivers/crypto/ccp/sp-platform.c:36:36: warning: tentative array
definition assumed to have one element
static const struct acpi_device_id sp_acpi_match[];
^
1 warning generated.
Just remove the forward declarations and move the initializations up
so that they can be used in sp_get_of_version and sp_get_acpi_version.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the quest to remove all stack VLA usage from the kernel[1], this
replaces struct crypto_skcipher and SKCIPHER_REQUEST_ON_STACK() usage
with struct crypto_sync_skcipher and SYNC_SKCIPHER_REQUEST_ON_STACK(),
which uses a fixed stack size.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary Hook <gary.hook@amd.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During PSP initialization, there is an attempt to update the SEV firmware
by looking in /lib/firmware/amd/. Currently, sev.fw is the expected name
of the firmware blob.
This patch will allow for firmware filenames based on the family and
model of the processor.
Model specific firmware files are given highest priority. Followed by
firmware for a subset of models. Lastly, failing the previous two options,
fallback to looking for sev.fw.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Under certain configuration SEV functions can be defined as no-op.
In such a case error can be uninitialized.
Initialize the variable to 0.
Cc: Dan Carpenter <Dan.Carpenter@oracle.com>
Reported-by: Dan Carpenter <Dan.Carpenter@oracle.com>
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, the CCP driver assumes that the SEV command issued to the PSP
will always return (i.e. it will never hang). But recently, firmware bugs
have shown that a command can hang. Since of the SEV commands are used
in probe routines, this can cause boot hangs and/or loss of virtualization
capabilities.
To protect against firmware bugs, add a timeout in the SEV command
execution flow. If a command does not complete within the specified
timeout then return -ETIMEOUT and stop the driver from executing any
further commands since the state of the SEV firmware is unknown.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary Hook <Gary.Hook@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Should the PSP initialization fail, the PSP data structure will be
freed and the value contained in the sp_device struct set to NULL.
At module unload, psp_dev_destroy() does not check if the pointer
value is NULL and will end up dereferencing a NULL pointer.
Add a pointer check of the psp_data field in the sp_device struct
in psp_dev_destroy() and return immediately if it is NULL.
Cc: <stable@vger.kernel.org> # 4.16.x-
Fixes: 2a6170dfe7 ("crypto: ccp: Add Platform Security Processor (PSP) device support")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a new CCP/PSP PCI device ID and new PSP register offsets.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In preparation for adding a new PSP device ID that uses different register
offsets, add support to the PSP version data for register offset values.
And then update the code to use these new register offset values.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove some unused #defines for register offsets that are not used. This
will lessen the changes required when register offsets change between
versions of the device.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a dev_notice() message to the PSP initialization to report when the
PSP initialization has succeeded and the PSP is enabled.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The wait_event() function is used to detect command completion. The
interrupt handler will set the wait condition variable when the interrupt
is triggered. However, the variable used for wait_event() is initialized
after the command has been submitted, which can create a race condition
with the interrupt handler and result in the wait_event() never returning.
Move the initialization of the wait condition variable to just before
command submission.
Fixes: 200664d523 ("crypto: ccp: Add Secure Encrypted Virtualization (SEV) command support")
Cc: <stable@vger.kernel.org> # 4.16.x-
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some ahash algorithms set .cra_type = &crypto_ahash_type. But this is
redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the .cra_type automatically.
Apparently the useless assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many ahash algorithms set .cra_flags = CRYPTO_ALG_TYPE_AHASH. But this
is redundant with the C structure type ('struct ahash_alg'), and
crypto_register_ahash() already sets the type flag automatically,
clearing any type flag that was already there. Apparently the useless
assignment has just been copy+pasted around.
So, remove the useless assignment from all the ahash algorithms.
This patch shouldn't change any actual behavior.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The GET_ID command, added as of SEV API v0.16, allows the SEV firmware
to be queried about a unique CPU ID. This unique ID can then be used
to obtain the public certificate containing the Chip Endorsement Key
(CEK) public key signed by the AMD SEV Signing Key (ASK).
For more information please refer to "Section 5.12 GET_ID" of
https://support.amd.com/TechDocs/55766_SEV-KM%20API_Specification.pdf
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DOWNLOAD_FIRMWARE command, added as of SEV API v0.15, allows the OS
to install SEV firmware newer than the currently active SEV firmware.
For the new SEV firmware to be applied it must:
* Pass the validation test performed by the existing firmware.
* Be of the same build or a newer build compared to the existing firmware.
For more information please refer to "Section 5.11 DOWNLOAD_FIRMWARE" of
https://support.amd.com/TechDocs/55766_SEV-KM%20API_Specification.pdf
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP driver copies data between scatter/gather lists and DMA buffers.
The length of the requested copy operation must be checked against
the available destination buffer length.
Reported-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Any change to the result buffer should only happen on final, finup
and digest operations. Changes to the buffer for update, import, export,
etc, are not allowed.
Fixes: 66d7b9f6175e ("crypto: testmgr - test misuse of result in ahash")
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix sparse warning: Using plain integer as NULL pointer. Replaces
assignment of 0 to pointer with NULL assignment.
Fixes: 200664d523 (Add Secure Encrypted Virtualization ...)
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
rsa-pkcs1pad uses a value returned from a RSA implementation max_size
callback as a size of an input buffer passed to the RSA implementation for
encrypt and sign operations.
CCP RSA implementation uses a hardware input buffer which size depends only
on the current RSA key length, so it should return this key length in
the max_size callback, too.
This also matches what the kernel software RSA implementation does.
Previously, the value returned from this callback was always the maximum
RSA key size the CCP hardware supports.
This resulted in this huge buffer being passed by rsa-pkcs1pad to CCP even
for smaller key sizes and then in a buffer overflow when ccp_run_rsa_cmd()
tried to copy this large input buffer into a RSA key length-sized hardware
input buffer.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Fixes: ceeec0afd6 ("crypto: ccp - Add support for RSA on the CCP")
Cc: stable@vger.kernel.org
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
I don't why we need take a single write lock and disable interrupts
while setting up debugfs. This is what what happens when we try anyway:
|ccp 0000:03:00.2: enabling device (0000 -> 0002)
|BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:69
|in_atomic(): 1, irqs_disabled(): 1, pid: 3, name: kworker/0:0
|irq event stamp: 17150
|hardirqs last enabled at (17149): [<0000000097a18c49>] restore_regs_and_return_to_kernel+0x0/0x23
|hardirqs last disabled at (17150): [<000000000773b3a9>] _raw_write_lock_irqsave+0x1b/0x50
|softirqs last enabled at (17148): [<0000000064d56155>] __do_softirq+0x3b8/0x4c1
|softirqs last disabled at (17125): [<0000000092633c18>] irq_exit+0xb1/0xc0
|CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.16.0-rc2+ #30
|Workqueue: events work_for_cpu_fn
|Call Trace:
| dump_stack+0x7d/0xb6
| ___might_sleep+0x1eb/0x250
| down_write+0x17/0x60
| start_creating+0x4c/0xe0
| debugfs_create_dir+0x9/0x100
| ccp5_debugfs_setup+0x191/0x1b0
| ccp5_init+0x8a7/0x8c0
| ccp_dev_init+0xb8/0xe0
| sp_init+0x6c/0x90
| sp_pci_probe+0x26e/0x590
| local_pci_probe+0x3f/0x90
| work_for_cpu_fn+0x11/0x20
| process_one_work+0x1ff/0x650
| worker_thread+0x1d4/0x3a0
| kthread+0xfe/0x130
| ret_from_fork+0x27/0x50
If any locking is required, a simple mutex will do it.
Cc: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Paulian reported the below kernel crash on Ryzen 5 system:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000073
RIP: 0010:.LC0+0x41f/0xa00
RSP: 0018:ffffa9968003bdd0 EFLAGS: 00010002
RAX: ffffffffb113b130 RBX: 0000000000000000 RCX: 00000000000005a7
RDX: 00000000000000ff RSI: ffff8b46dee651a0 RDI: ffffffffb1bd617c
RBP: 0000000000000246 R08: 00000000000251a0 R09: 0000000000000000
R10: ffffd81f11a38200 R11: ffff8b52e8e0a161 R12: ffffffffb19db220
R13: 0000000000000007 R14: ffffffffb17e4888 R15: 5dccd7affc30a31e
FS: 0000000000000000(0000) GS:ffff8b46dee40000(0000) knlGS:0000000000000000
CR2: 0000000000000073 CR3: 000080128120a000 CR4: 00000000003406e0
Call Trace:
? sp_get_psp_master_device+0x56/0x80
? map_properties+0x540/0x540
? psp_pci_init+0x20/0xe0
? map_properties+0x540/0x540
? sp_mod_init+0x16/0x1a
? do_one_initcall+0x4b/0x190
? kernel_init_freeable+0x19b/0x23c
? rest_init+0xb0/0xb0
? kernel_init+0xa/0x100
? ret_from_fork+0x22/0x40
Since Ryzen does not support PSP/SEV firmware hence i->psp_data will
NULL in all sp instances. In those cases, 'i' will point to the
list head after list_for_each_entry(). Dereferencing the head will
cause kernel crash.
Add check to call get master device only when PSP/SEV is detected.
Reported-by: Paulian Bogdan Marinca <paulian@marinca.net>
Cc: Borislav Petkov <bp@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
CC: Gary R Hook <gary.hook@amd.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Function ccp_get_dma_chan_attr is local to the source and does not
need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/crypto/ccp/ccp-dmaengine.c:41:14: warning: symbol
'ccp_get_dma_chan_attr' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARM:
- Include icache invalidation optimizations, improving VM startup time
- Support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- A small fix for power-management notifiers, and some cosmetic changes
PPC:
- Add MMIO emulation for vector loads and stores
- Allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- Improve the handling of escalation interrupts with the XIVE interrupt
controller
- Support decrement register migration
- Various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- Exitless interrupts for emulated devices
- Cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- Hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- Paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- Allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more AVX512
features
- Show vcpu id in its anonymous inode name
- Many fixes and cleanups
- Per-VCPU MSR bitmaps (already merged through x86/pti branch)
- Stable KVM clock when nesting on Hyper-V (merged through x86/hyperv)
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJafvMtAAoJEED/6hsPKofo6YcH/Rzf2RmshrWaC3q82yfIV0Qz
Z8N8yJHSaSdc3Jo6cmiVj0zelwAxdQcyjwlT7vxt5SL2yML+/Q0st9Hc3EgGGXPm
Il99eJEl+2MYpZgYZqV8ff3mHS5s5Jms+7BITAeh6Rgt+DyNbykEAvzt+MCHK9cP
xtsIZQlvRF7HIrpOlaRzOPp3sK2/MDZJ1RBE7wYItK3CUAmsHim/LVYKzZkRTij3
/9b4LP1yMMbziG+Yxt1o682EwJB5YIat6fmDG9uFeEVI5rWWN7WFubqs8gCjYy/p
FX+BjpOdgTRnX+1m9GIj0Jlc/HKMXryDfSZS07Zy4FbGEwSiI5SfKECub4mDhuE=
=C/uD
-----END PGP SIGNATURE-----
Merge tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Radim Krčmář:
"ARM:
- icache invalidation optimizations, improving VM startup time
- support for forwarded level-triggered interrupts, improving
performance for timers and passthrough platform devices
- a small fix for power-management notifiers, and some cosmetic
changes
PPC:
- add MMIO emulation for vector loads and stores
- allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
requiring the complex thread synchronization of older CPU versions
- improve the handling of escalation interrupts with the XIVE
interrupt controller
- support decrement register migration
- various cleanups and bugfixes.
s390:
- Cornelia Huck passed maintainership to Janosch Frank
- exitless interrupts for emulated devices
- cleanup of cpuflag handling
- kvm_stat counter improvements
- VSIE improvements
- mm cleanup
x86:
- hypervisor part of SEV
- UMIP, RDPID, and MSR_SMI_COUNT emulation
- paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit
- allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
AVX512 features
- show vcpu id in its anonymous inode name
- many fixes and cleanups
- per-VCPU MSR bitmaps (already merged through x86/pti branch)
- stable KVM clock when nesting on Hyper-V (merged through
x86/hyperv)"
* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
KVM: PPC: Book3S HV: Branch inside feature section
KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
KVM: PPC: Book3S PR: Fix broken select due to misspelling
KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
KVM: PPC: Book3S HV: Drop locks before reading guest memory
kvm: x86: remove efer_reload entry in kvm_vcpu_stat
KVM: x86: AMD Processor Topology Information
x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
kvm: embed vcpu id to dentry of vcpu anon inode
kvm: Map PFN-type memory regions as writable (if possible)
x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
KVM: arm/arm64: Fixup userspace irqchip static key optimization
KVM: arm/arm64: Fix userspace_irqchip_in_use counting
KVM: arm/arm64: Fix incorrect timer_is_pending logic
MAINTAINERS: update KVM/s390 maintainers
MAINTAINERS: add Halil as additional vfio-ccw maintainer
MAINTAINERS: add David as a reviewer for KVM/s390
...
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEV_PDH_CERT_EXPORT command can be used to export the PDH and its
certificate chain. The command is defined in SEV spec section 5.10.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
The SEV_PEK_CERT_IMPORT command can be used to import the signed PEK
certificate. The command is defined in SEV spec section 5.8.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
The SEV_PEK_CSR command can be used to generate a PEK certificate
signing request. The command is defined in SEV spec section 5.7.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
The SEV_PDH_GEN command is used to re-generate the Platform
Diffie-Hellman (PDH) key. The command is defined in SEV spec section
5.6.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Gary R Hook <gary.hook@amd.com>
The SEV_PEK_GEN command is used to generate a new Platform Endorsement
Key (PEK). The command is defined in SEV spec section 5.6.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Borislav Petkov <bp@suse.de>
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
The SEV_PLATFORM_STATUS command can be used by the platform owner to
get the current status of the platform. The command is defined in
SEV spec section 5.5.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Acked-by: Gary R Hook <gary.hook@amd.com>
The SEV_FACTORY_RESET command can be used by the platform owner to
reset the non-volatile SEV related data. The command is defined in
SEV spec section 5.4
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
AMD's new Secure Encrypted Virtualization (SEV) feature allows the
memory contents of virtual machines to be transparently encrypted with a
key unique to the VM. The programming and management of the encryption
keys are handled by the AMD Secure Processor (AMD-SP) which exposes the
commands for these tasks. The complete spec is available at:
http://support.amd.com/TechDocs/55766_SEV-KM%20API_Specification.pdf
Extend the AMD-SP driver to provide the following support:
- an in-kernel API to communicate with the SEV firmware. The API can be
used by the hypervisor to create encryption context for a SEV guest.
- a userspace IOCTL to manage the platform certificates.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
The Platform Security Processor (PSP) is part of the AMD Secure
Processor (AMD-SP) functionality. The PSP is a dedicated processor
that provides support for key management commands in Secure Encrypted
Virtualization (SEV) mode, along with software-based Trusted Execution
Environment (TEE) to enable third-party trusted applications.
Note that the key management functionality provided by the SEV firmware
can be used outside of the kvm-amd driver hence it doesn't need to
depend on CONFIG_KVM_AMD.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-crypto@vger.kernel.org
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Improvements-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
This is AMD-specific hardware so present it in Kconfig only when AMD
CPU support is enabled or on ARM64 where it is also used.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Reviewed-by: Gary R Hook <gary.hook@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.15:
API:
- Disambiguate EBUSY when queueing crypto request by adding ENOSPC.
This change touches code outside the crypto API.
- Reset settings when empty string is written to rng_current.
Algorithms:
- Add OSCCA SM3 secure hash.
Drivers:
- Remove old mv_cesa driver (replaced by marvell/cesa).
- Enable rfc3686/ecb/cfb/ofb AES in crypto4xx.
- Add ccm/gcm AES in crypto4xx.
- Add support for BCM7278 in iproc-rng200.
- Add hash support on Exynos in s5p-sss.
- Fix fallback-induced error in vmx.
- Fix output IV in atmel-aes.
- Fix empty GCM hash in mediatek.
Others:
- Fix DoS potential in lib/mpi.
- Fix potential out-of-order issues with padata"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
lib/mpi: call cond_resched() from mpi_powm() loop
crypto: stm32/hash - Fix return issue on update
crypto: dh - Remove pointless checks for NULL 'p' and 'g'
crypto: qat - Clean up error handling in qat_dh_set_secret()
crypto: dh - Don't permit 'key' or 'g' size longer than 'p'
crypto: dh - Don't permit 'p' to be 0
crypto: dh - Fix double free of ctx->p
hwrng: iproc-rng200 - Add support for BCM7278
dt-bindings: rng: Document BCM7278 RNG200 compatible
crypto: chcr - Replace _manual_ swap with swap macro
crypto: marvell - Add a NULL entry at the end of mv_cesa_plat_id_table[]
hwrng: virtio - Virtio RNG devices need to be re-registered after suspend/resume
crypto: atmel - remove empty functions
crypto: ecdh - remove empty exit()
MAINTAINERS: update maintainer for qat
crypto: caam - remove unused param of ctx_map_to_sec4_sg()
crypto: caam - remove unneeded edesc zeroization
crypto: atmel-aes - Reset the controller before each use
crypto: atmel-aes - properly set IV after {en,de}crypt
hwrng: core - Reset user selected rng by writing "" to rng_current
...
Replace -EBUSY with -ENOSPC when reporting transient busy
indication in the absence of backlog.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Reviewed-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Variable qim is assigned but never read, it is redundant and can
be removed.
Cleans up clang warning: Value stored to 'qim' is never read
Fixes: 4b394a232d ("crypto: ccp - Let a v5 CCP provide the same function as v3")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the provided mechanism in dmaengine.h to invoke the
completion callback.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean up the mapped pages and the unmap object once we are done with
it. This enables the final clean-up of the object once the transfer
is complete.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch replace GCM IV size value by their constant name.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- Removal of DMA_SG support as we have no users for this feature
- New driver for Altera / Intel mSGDMA IP core
- Support for memset in dmatest and qcom_hidma driver
- Update for non cyclic mode in k3dma, bunch of update in bam_dma, bcm sba-raid
- Constify device ids across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=88SI
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.14-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This one features the usual updates to the drivers and one good part
of removing DA_SG from core as it has no users.
Summary:
- Remove DMA_SG support as we have no users for this feature
- New driver for Altera / Intel mSGDMA IP core
- Support for memset in dmatest and qcom_hidma driver
- Update for non cyclic mode in k3dma, bunch of update in bam_dma,
bcm sba-raid
- Constify device ids across drivers"
* tag 'dmaengine-4.14-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (52 commits)
dmaengine: sun6i: support V3s SoC variant
dmaengine: sun6i: make gate bit in sun8i's DMA engines a common quirk
dmaengine: rcar-dmac: document R8A77970 bindings
dmaengine: xilinx_dma: Fix error code format specifier
dmaengine: altera: Use macros instead of structs to describe the registers
dmaengine: ti-dma-crossbar: Fix dra7 reserve function
dmaengine: pl330: constify amba_id
dmaengine: pl08x: constify amba_id
dmaengine: bcm-sba-raid: Remove redundant SBA_REQUEST_STATE_COMPLETED
dmaengine: bcm-sba-raid: Explicitly ACK mailbox message after sending
dmaengine: bcm-sba-raid: Add debugfs support
dmaengine: bcm-sba-raid: Remove redundant SBA_REQUEST_STATE_RECEIVED
dmaengine: bcm-sba-raid: Re-factor sba_process_deferred_requests()
dmaengine: bcm-sba-raid: Pre-ack async tx descriptor
dmaengine: bcm-sba-raid: Peek mbox when we have no free requests
dmaengine: bcm-sba-raid: Alloc resources before registering DMA device
dmaengine: bcm-sba-raid: Improve sba_issue_pending() run duration
dmaengine: bcm-sba-raid: Increase number of free sba_request
dmaengine: bcm-sba-raid: Allow arbitrary number free sba_request
dmaengine: bcm-sba-raid: Remove reqs_free_count from sba_device
...
There are no in kernel consumers for DMA_SG op. Removing operation,
dead code, and test code in dmatest.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Gary Hook <gary.hook@amd.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Kedareswara rao Appana <appana.durga.rao@xilinx.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function ccp_init_dm_workarea(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Without the base RSA code, we run into a link error:
ERROR: "rsa_parse_pub_key" [drivers/crypto/ccp/ccp-crypto.ko] undefined!
ERROR: "rsa_parse_priv_key" [drivers/crypto/ccp/ccp-crypto.ko] undefined!
Like the other drivers implementing RSA in hardware, this
can be avoided by always enabling the base support when we build
CCP.
Fixes: ceeec0afd6 ("crypto: ccp - Add support for RSA on the CCP")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The added support for version 5 CCPs introduced a false-positive
warning in the RSA implementation:
drivers/crypto/ccp/ccp-ops.c: In function 'ccp_run_rsa_cmd':
drivers/crypto/ccp/ccp-ops.c:1856:3: error: 'sb_count' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the code in a way that should make it easier for
the compiler to track the state of the sb_count variable, and
avoid the warning.
Fixes: 6ba46c7d4d ("crypto: ccp - Fix base RSA function for version 5 CCPs")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP supports a limited set of unit-size values. Change the check
for this parameter such that acceptable values match the enumeration.
Then clarify the conditions under which we must use the fallback
implementation.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Vet the key using the available standard function
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Version 5 CCPs have some new requirements for XTS-AES: the type field
must be specified, and the key requires 512 bits, with each part
occupying 256 bits and padded with zeroes.
cc: <stable@vger.kernel.org> # 4.9.x+
Signed-off-by: Gary R Hook <ghook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
commit 720419f018 ("crypto: ccp - Introduce the AMD Secure Processor device")
moved the module registeration from ccp-dev.c to sp-dev.c but patch missed
removing the module version and author entry from ccp-dev.c.
It causes the below warning during boot when CONFIG_CRYPTO_DEV_SP_CCP=y
and CONFIG_CRYPTO_DEV_CCP_CRYPTO=y is set.
[ 0.187825] sysfs: cannot create duplicate filename '/module/ccp/version'
[ 0.187825] sysfs: cannot create duplicate filename '/module/ccp/version'
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Gary R Hook <gary.hook@amd.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
A version 5 CCP can handle an RSA modulus up to 16k bits.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Version 5 devices have requirements for buffer lengths, as well as
parameter format (e.g. bits vs. bytes). Fix the base CCP driver
code to meet requirements all supported versions.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some updates this year have not had copyright dates changed in modified
files. Correct this for 2017.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since SP device driver supports multiples devices (e.g CCP, PSP), we
should not fail the driver init just because CCP device is not found.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CCP device initializes is now integerated into higher level SP device,
to avoid the confusion lets rename the ccp driver initialization files
(ccp-platform.c->sp-platform.c, ccp-pci.c->sp-pci.c). The patch does not
make any functional changes other than renaming file and structures
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP and PSP devices part of AMD Secure Procesor may share the same
interrupt. Hence we expand the SP device to register a common interrupt
handler and provide functions to CCP and PSP devices to register their
interrupt callback which will be invoked upon interrupt.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The CCP device is part of the AMD Secure Processor. In order to expand
the usage of the AMD Secure Processor, create a framework that allows
functional components of the AMD Secure Processor to be initialized and
handled appropriately.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update pci and platform files to use devres interface to allocate the PCI
and iomap resources. Also add helper functions to consolicate module init,
exit and power mangagement code duplication.
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Acked-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Print error message on platform_get_irq failure before return.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Changes since v2:
- On failure remove only the DebugFS heirarchy for this device
Changes since v1:
- Remove unneeded local variable
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
