Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable MMC/SD on the Broadcom mobile platforms, and increase the block
minors from the default 8 to 16 (since the Broadcom board by default
has root on the 8th partition).
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.12
This enables a few more options on the sunxi defconfigs such that I can
use nfsroot to boot them (there is no local storage support yet). It
also enables PRINTK_TIME and tmpfs since it's a common distro requirement.
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
BeagleBone Black uses the TI CPSW ethernet controller, enable it in the
multi_v7_defconfig for testing coverage purposes.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v3.12
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 'cd8abed' "ARM: OMAP2+: Powerdomain: Remove the need to
always have a voltdm associated to a pwrdm" leads to the following
Smatch complaint:
arch/arm/mach-omap2/powerdomain.c:131 _pwrdm_register()
error: we previously assumed 'arch_pwrdm' could be null (see line 105)
So, fix the unchecked dereference of arch_pwrdm.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_PM is not defined, then arch/arm/mach-at91/pm.c is not
compiled in. This patch creates an inline function that does nothing
if CONFIG_PM is not defined.
Signed-off-by: Brent Taylor <motobud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
With some devices, transfer hangs during I2C frame transmission. This issue
disappears when reducing the internal frequency of the TWI IP. Even if it is
indicated that internal clock max frequency is 66MHz, it seems we have
oversampling on I2C signals making TWI believe that a transfer in progress
is done.
This fix has no impact on the I2C bus frequency.
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some features can be configured by the companion I2C chips,
which may not be available at the probe time. Fix the issue
by returning -EPROBE_DEFER when the MMC controller slots
are not configured.
While at it, let's also add minimal device tree support so
omap24xx platforms can use this driver without legacy mode
since we claim to support device tree for mach-omap2 based
systems.
Although adding the minimal device tree support is not strictly
a fix, it does remove one of the last blockers for dropping a
bunch of legacy platform data for mach-omap2.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are wrongly relying on device id for the DMA configuration
which can lead to wrong DMA channel being selected.
Fix the issue by using the standard resources like we should.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:
[ 3.186035] OMAPFB: omapfb_probe
[ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[ 3.196594] omapfb omapfb: failed to connect default display
[ 3.202667] omapfb omapfb: failed to init overlay connections
[ 3.208892] OMAPFB: free_resources
[ 3.212493] OMAPFB: free all fbmem
[ 3.216735] omapfb omapfb: failed to setup omapfb
As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).
Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.
To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP's DVI connector's DDC pins are connected to OMAP's third i2c bus.
When booting with Device Trees the requested bus number is set to -1
which means that the bus number should be dynamically assigned. So the
third i2c bus has 2 has a bus number.
Since now only DT booting is supported for IGEP boards after commit
06ff74fd ("ARM: OMAP2+: remove legacy support for IGEP boards"), the
i2c bus number has to be changed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling of Posted mode is seen to cause problems on dmtimer modules on AM33xx
(much like other OMAPs). Reference discussions on forums [1] [2]. Earlier
patch solving this on other OMAPs [3].
For OMAP SoCs with this errata, the fix has been to not enable Posted mode.
However, on some SoCs (atleast AM33xx) which carry this errata, Posted mode
is enabled on reset. So we not only need to ignore enabling of the POSTED bit
when the timer is requested, but also disable Posted mode if errata is present.
[1] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/285744.aspx
[2] http://e2e.ti.com/support/arm/sitara_arm/f/791/t/270632.aspx
[3] http://www.spinics.net/lists/linux-omap/msg81770.html
Cc: stable@vgerk.kernel.org
Reported-by: Russ Dill <russ.dill@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Allow creation and mounting of devtmpfs, which is used
by OpenEmbedded root filesystems among others.
- Enable CPUidle for the ux500, it has been accidentally
disabled due to a Kconfig change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=jJ0N
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, Ux500 defconfig patches for the v3.13 rc series:
- Allow creation and mounting of devtmpfs, which is used
by OpenEmbedded root filesystems among others.
- Enable CPUidle for the ux500, it has been accidentally
disabled due to a Kconfig change.
* tag 'ux500-defconfig-v3.13-rcs' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: u8500_defconfig: add missing cpuidle option
u8500_defconfig: allow creation and mounting of devtmpfs
- Restore platform data for the (e)MMC/SD controllers, so they can
pins and special flags properly like before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=VO2C
-----END PGP SIGNATURE-----
Merge tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
From Linus Walleij, Ux500 fixes for the v3.13 series:
- Restore platform data for the (e)MMC/SD controllers, so they can
pins and special flags properly like before.
* tag 'ux500-fixes-v3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
Revert "ARM: ux500: Stop passing MMC's platform data for Device Tree boots"
Revert "ARM: ux500: Remove AUXDATA relating to SDI (MMC) clock-name bindings"
This reverts commit 49c129519a.
The special settings for the SD/MMC card parameters that are not
yet fully agreed upon how to encode into the device tree went missing
with this commit. We need to first put it into the device tree,
and then remove the platform data.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit ce16feb851.
This commit stopped tying down the name of the MMC/SD devices, but these
names are used in the pin control table, so the MMC/SD cards stopped
working.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the commit d3f2950f2a, the option
ARM_U8500_CPUIDLE was added to the Kconfig but not reflected in the
default config file, hence the cpuidle driver is no longer enabled
since this commit.
Enable it again by adding the missing option in the default config file.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables CONFIG_DETTMPFS and CONFIG_DEVTMPFS_MOUNT
flags for u8500 based devices.
In this way it's possible to create a tmpfs/ramfs already in the
early stages of the boot, allowing programs like udev/mdev to
populate the /dev directory.
Signed-off-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Looks like we need to configure the regulators and use the pdata
quirk to make eMMC work with device tree.
It seems that mostly vaux3 is used, and only some earlier revisions
used vmmc2. This has been tested to work on devices where the
system_rev passed by the bootloader has versions 0x0010, 0x2101
and 0x2204.
Cc: devicetree@vger.kernel.org
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@debian.org>
[tony@atomide.com: updated with pinctrl changes and comments from Sebastian]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We do not have REGULATOR_FIXED selected if no boards are selected
and we boot with device tree. This can cause various devices to
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
After dropping the duplicate data in hwmod that now should come from
the .dts files, I noticed few more entries missing. Let's add these
as otherwise devices relying on these won't work.
Looks like the side tone entries are bundled into the mcbsp1 to 3,
so that may needs some special handling in the hwmod code as it's
currently trying to look up mcbsp2_sidetone and mcbsp3_sidetone
entries.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch implements the power_down_finish() method for TC2, to
enable the kernel to confirm when CPUs are safely powered down.
The information required for determining when a CPU is parked
cannot be obtained from any single place, so a few sources of
information must be combined:
* mcpm_cpu_power_down() must be pending for the CPU, so that we
don't get confused by false STANDBYWFI positives arising from
CPUidle. This is detected by waiting for the tc2_pm use count
for the target CPU to reach 0.
* Either the SPC must report that the CPU has asserted
STANDBYWFI, or the TC2 tile's reset control logic must be
holding the CPU in reset.
Just checking for STANDBYWFI is not sufficient, because this
signal is not latched when the the cluster is clamped off and
powered down: the relevant status bits just drop to zero. This
means that STANDBYWFI status cannot be used for reliable
detection of the last CPU in a cluster reaching WFI.
This patch is required in order for kexec to work with MCPM on TC2.
MCPM code was changed in commit 0de0d64675 ('ARM: 7848/1: mcpm:
Implement cpu_kill() to synchronise on powerdown'), and since then it
will hit a WARN_ON_ONCE() due to power_down_finish not being implemented
on the TC2 platform.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.
This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:
drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more fixes for issues found booting older omaps using device tree.
Also few randconfig build fixes and removal of some dead code for omap4
as it no longer has legacy platform data based booting support.
* tag 'omap-for-v3.13/more-fixes-for-merge-window-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Some omap3 code is throwing a warning:
arch/arm/mach-omap2/pm34xx.c: In function 'omap3_save_secure_ram_context':
arch/arm/mach-omap2/pm34xx.c:123:32: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
In reality this code will never actually execute with LPAE=y, since
Cortex-A8 doesn't support it. So downcasting the __pa() is safe in
this case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Commit 14fd8ed0a7 ("ARM: mvebu: Relocate Armada 370/XP PCIe
device tree nodes") relocated the PCIe controller DT nodes one level
up in the Device Tree, to reflect a more correct representation of the
hardware introduced by the mvebu-mbus Device Tree binding.
However, while most of the boards were properly adjusted accordingly,
the Armada 370 DB board was left unchanged, and therefore, PCIe is
seen as not enabled on this board. This patch fixes that by moving the
PCIe controller node one level-up in armada-370-db.dts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.12+
Fixes: 14fd8ed0a7 "ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes"
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP provides a mechanism called "virtual CPU registers" or
"per-CPU register banking", to access the per-CPU registers of the
current CPU, without having to worry about finding on which CPU we're
running. CPU0 has its registers at 0x21800, CPU1 at 0x21900, CPU2 at
0x21A00 and CPU3 at 0x21B00. The virtual registers accessing the
current CPU registers are at 0x21000.
However, in the Device Tree node that provides the register addresses
for the coherency unit (which is responsible for ensuring coherency
between processors, and I/O coherency between processors and the
DMA-capable devices), a mistake was made: the CPU0-specific registers
were specified instead of the virtual CPU registers. This means that
the coherency barrier needed for I/O coherency was not behaving
properly when executed from a CPU different from CPU0. This patch
fixes that by using the virtual CPU registers.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: e60304f8cb "arm: mvebu: Add hardware I/O Coherency support"
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
