2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-26 06:04:14 +08:00
Commit Graph

1904 Commits

Author SHA1 Message Date
Tobias Klauser
5bcd601049 serial: Add driver for the Altera JTAG UART
Add an UART driver for the JTAG UART component available as a SOPC
(System on Programmable Chip) component for Altera FPGAs.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:30 -07:00
Richard Röjfors
24cd73a394 serial: timbuart: make sure last byte is sent when port is closed
Fix a problem in early versions of the FPGA IP.

In certain situations the IP reports that the FIFO is empty, but a byte is
still clocked out.  If a flush is done at that point the currently clocked
byte is canceled.

This causes incompatibilities with the upper layers when a port is closed,
it waits until the FIFO is empty and then closes the port.  During close
the FIFO is flushed -> the last byte is not sent properly.

Now the FIFO is only flushed if it is reported to be non-empty.  Which
makes the currently clocked out byte to finish.

[akpm@linux-foundation.org: fix build]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:29 -07:00
Roel Kluin
4405199623 serial: two branches the same in timbuart_set_mctrl()
CTS is a read only bit and we are to stop signal RTS if modem line
TIOCM_RTS is not set.

Thanks for suggestions by Richard Röjfors.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:29 -07:00
John Linn
e5bbbb18d8 serial: uartlite: move from byte accesses to word accesses
Byte accesses for I/O devices in Xilinx IP is going to be less
desired in the future such that the driver is being changed to
use 32 bit accesses.

This change facilitates using the uartlite IP over a PCIe bus
which only allows 32 bit accesses.

Signed-off-by: John Linn <john.linn@xilinx.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:29 -07:00
Mike Frysinger
be991593f8 serial: bfin_sport_uart: drop redundant cpu depends
The BF54xM procs imply the related BF54x define, so no need to check both.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:28 -07:00
Mike Frysinger
d671250b98 serial: bfin_sport_uart: drop the experimental markings
Should be stable now ...

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:28 -07:00
Mike Frysinger
2ce1efc9e3 serial: bfin_sport_uart: pull in bfin_sport.h for SPORT defines
Now that the SPORT MMR defines have been unified, switch over to it.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:28 -07:00
Sonic Zhang
9356c46170 serial: bfin_sport_uart: only enable SPORT TX if data is to be sent
Rather than always turn on the SPORT TX interrupt, only do it when we've
actually queued up data for transmission.  This avoids useless interrupt
processing.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:28 -07:00
Mike Frysinger
60bd940f14 serial: bfin_sport_uart: drop useless status masks
These were all copied over from the Blackfin UART driver, but they don't
make sense here because these bits are all specific to the Blackfin UART.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:28 -07:00
Sonic Zhang
f4d10ca895 serial: bfin_sport_uart: zero sport_uart_port if allocated dynamically
Need to initialize the SPORT state rather than using random memory.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:28 -07:00
Sonic Zhang
9498dc95ca serial: bfin_sport_uart: protect changes to uart_port
Common serial API says we need to grab the port lock before modifying
the port state to prevent inconsistent state between threads.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Sonic Zhang
1f7d1c85df serial: bfin_sport_uart: add support for CTS/RTS via GPIOs
Some people need flow control on their ports, so now boards can support
that via any GPIOs.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Sonic Zhang
b59588aae8 serial: bfin_sport_uart: rename early platform driver class string
Clarifies command line set up for devices between consoles and early
devices.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Sonic Zhang
e8126b32f6 serial: bfin_sport_uart: add missing mapbase initialization
The driver doesn't care about this, but the common serial core wants it.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Sonic Zhang
00c1ff8c0f serial: bfin_sport_uart: remove unused peripheral pin lists
All the resources are in the boards files now.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Sonic Zhang
3f3a978b9f serial: bfin_sport_uart: shorten the SPORT TX waiting loop
The waiting loop to stop SPORT TX from TX interrupt is too long.  This may
block the SPORT RX interrupts and cause the RX FIFO to overflow. So, do
stop sport TX only after the last char in TX FIFO is moved into the shift
register.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Sonic Zhang
a5a420d207 serial: bfin_sport_uart: work around anomaly 05000473 (make 32bit fifo read atomic)
We cannot let a 32-bit RX FIFO read be interrupted otherwise a fake RX
underflow error might be generated.

URL: http://blackfin.uclinux.org/gf/tracker/5145

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-21 09:34:27 -07:00
Jason Wessel
9731191f75 kgdboc: Add ekgdboc for early use of the kernel debugger
The ekgdboc= differs from kgdboc= in that you can begin debuggin as
soon as the exceptions are setup and the kgdb I/O driver is available,
instead of waiting until the tty subsystem is available.

CC: kgdb-bugreport@lists.sourceforge.net
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2010-05-20 21:04:30 -05:00
Jason Wessel
efe2f29e32 kgdboc,kdb: Allow kdb to work on a non open console port
If kdb is open on a serial port that is not actually a console make
sure to call the poll routines to emit and receive characters.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Martin Hicks <mort@sgi.com>
2010-05-20 21:04:26 -05:00
Jason Wessel
ada64e4c98 kgdboc,keyboard: Keyboard driver for kdb with kgdb
This patch adds in the kdb PS/2 keyboard driver.  This was mostly a
direct port from the original kdb where I cleaned up the code against
checkpatch.pl and added the glue to stitch it into kgdb.

This patch also enables early kdb debug via kgdbwait and the keyboard.

All the access to configure kdb using either a serial console or the
keyboard is done via kgdboc.

If you want to use only the keyboard and want to break in early you
would add to your kernel command arguments:

    kgdboc=kbd kgdbwait

If you wanted serial and or the keyboard access you could use:

    kgdboc=kbd,ttyS0

You can also configure kgdboc as a kernel module or at run time with
the sysfs where you can activate and deactivate kgdb.

Turn it on:
    echo kbd,ttyS0 > /sys/module/kgdboc/parameters/kgdboc

Turn it off:
    echo "" > /sys/module/kgdboc/parameters/kgdboc

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2010-05-20 21:04:24 -05:00
Jason Wessel
6d45a1aed3 sparc,sunzilog: Add console polling support for sunzilog serial driver
Allow kgdboc to work on sparc hardware with the Zilog serial chips.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: David S. Miller <davem@davemloft.net>
2010-05-20 21:04:23 -05:00
Jason Wessel
3f255eb37e sh,sh-sci: Use NO_POLL_CHAR in the SCIF polled console code
The sci_poll_get_char() needs to return immediately if there is no
input from the chip to process, and must return a value of
NO_POLL_CHAR.

This allows kgdboc to process multiple polled devices while kgdb is
active.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
2010-05-20 21:04:23 -05:00
Jason Wessel
f5316b4aea kgdb,8250,pl011: Return immediately from console poll
The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available.  This is required in order to get the
page scrolling mechanism working.

Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.

NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.

CC: linux-serial@vger.kernel.org
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2010-05-20 21:04:22 -05:00
Linus Torvalds
5429126351 Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (29 commits)
  pcmcia: disable PCMCIA ioctl also for ARM
  drivers/staging/comedi: dev_node removal (quatech_daqp_cs)
  drivers/staging/comedi: dev_node removal (ni_mio_cs)
  drivers/staging/comedi: dev_node removal (ni_labpc_cs)
  drivers/staging/comedi: dev_node removal (ni_daq_dio24)
  drivers/staging/comedi: dev_node removal (ni_daq_700)
  drivers/staging/comedi: dev_node removal (das08_cs)
  drivers/staging/comedi: dev_node removal (cb_das16_cs)
  pata_pcmcia: get rid of extra indirection
  pcmcia: remove suspend-related comment from yenta_socket.c
  pcmcia: call pcmcia_{read,write}_cis_mem with ops_mutex held
  pcmcia: remove pcmcia_add_device_lock
  pcmcia: update gfp/slab.h includes
  pcmcia: remove unused mem_op.h
  pcmcia: do not autoadd root PCI bus resources
  pcmcia: clarify alloc_io_space, move it to resource handlers
  pcmcia: move all pcmcia_resource_ops providers into one module
  pcmcia: move high level CIS access code to separate file
  pcmcia: dev_node removal (core)
  pcmcia: dev_node removal (remaining drivers)
  ...
2010-05-20 09:09:46 -07:00
Linus Torvalds
349e1fba7e Merge branch 'for-linus/samsung4' of git://git.fluff.org/bjdooks/linux
* 'for-linus/samsung4' of git://git.fluff.org/bjdooks/linux: (98 commits)
  Input: s3c24xx_ts - depend on SAMSUNG_DEV_TS and update menu entry
  Input: s3c24xx_ts - Add FEAT for Samsung touchscreen support
  Input: s3c24xx_ts - Implement generic GPIO configuration callback
  ARM: SAMSUNG: Move s3c64xx dev-ts.c to plat-samsung and rename configuration
  ARM: SAMSUNG: Implements cfg_gpio function for Samsung touchscreen
  ARM: S3C64XX: Add touchscreen platform device definition
  ARM: SAMSUNG: Move mach/ts.h to plat/ts.h
  ARM: S5PC100: Move i2c helpers from plat-s5pc1xx to mach-s5pc100
  ARM: S5PC100: Move frame buffer helpers from plat-s5pc1xx to mach-s5pc100
  ARM: S5PC100: gpio.h cleanup
  ARM: S5PC100: Move gpio support from plat-s5pc1xx to mach-s5pc100
  ARM: S5PC100: Use common functions for gpiolib implementation
  drivers: serial: S5PC100 serial driver cleanup
  ARM: S5PC100: Pre-requisite clock patch for plat-s5pc1xx to plat-s5p move
  ARM: SAMSUNG: Copy common I2C0 device helpers to machine directories
  ARM: SAMSUNG: move driver strength gpio configuration helper to common dir
  ARM: S5PV210: Add GPIOlib support
  ARM: SAMSUNGy: fix broken timer irq base
  ARM: SMDK6440: Add audio devices on board
  ARM: S5P6440: Add audio platform devices
  ...
2010-05-19 11:49:33 -07:00
Linus Torvalds
1d3c6ff44a Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (224 commits)
  ARM: remove 'select GENERIC_TIME'
  ARM: 6136/1: ARCH_REQUIRE_GPIOLIB selects GENERIC_GPIO
  ARM: 6074/1: oprofile: convert from sysdev to platform device
  ARM: 6073/1: oprofile: remove old files and update KConfig
  ARM: 6072/1: oprofile: use perf-events framework as backend
  ARM: 6071/1: perf-events: allow modules to query the number of hardware counters
  ARM: 6070/1: perf-events: add support for xscale PMUs
  ARM: 6069/1: perf-events: use numeric ID to identify PMU
  ARM: 6064/1: pmu: register IRQs at runtime
  ARM: Optionally allow ARMv6 to use 'normal, bufferable' memory for DMA
  ARM: 6134/1: Handle instruction cache maintenance fault properly
  ARM: nwfpe: allow debugging output to be configured at runtime
  ARM: rename mach_cpu_disable() to platform_cpu_disable()
  ARM: 6132/1: PL330: Add common core driver
  ARM: 6094/1: Extend cache-l2x0 to support the 16-way PL310
  ARM: Move memory mapping into mmu.c
  ARM: Ensure meminfo is sorted prior to sanity_check_meminfo
  ARM: Remove useless linux/bootmem.h includes
  ARM: convert /proc/cpu/aligment to seq_file
  arm: use asm-generic/scatterlist.h
  ...
2010-05-19 11:37:22 -07:00
Linus Torvalds
7c7cbaf5b8 Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (127 commits)
  sh: update defconfigs.
  sh: Fix up the NUMA build for recent LMB changes.
  sh64: provide a stub per_cpu_trap_init() definition.
  sh: fix up CONFIG_KEXEC=n build.
  sh: fixup the docbook paths for clock framework shuffling.
  driver core: Early dev_name() depends on slab_is_available().
  sh: simplify WARN usage in SH clock driver
  sh: Check return value of clk_get on ms7724
  sh: Check return value of clk_get on ecovec24
  sh: move sh clock-cpg.c contents to drivers/sh/clk-cpg.c
  sh: move sh clock.c contents to drivers/sh/clk.
  sh: move sh asm/clock.h contents to linux/sh_clk.h V2
  sh: remove unused clock lookup
  sh: switch boards to clkdev
  sh: switch sh4-202 to clkdev
  sh: switch shx3 to clkdev
  sh: switch sh7757 to clkdev
  sh: switch sh7763 to clkdev
  sh: switch sh7780 to clkdev
  sh: switch sh7786 to clkdev
  ...
2010-05-19 11:36:03 -07:00
Marek Szyprowski
cb34a67472 drivers: serial: S5PC100 serial driver cleanup
Remove unnecessary Kconfig entry. S5PC100 has exactly the same driver as
S3C6400/S3C6410/S5P6440.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-05-19 18:22:55 +09:00
Grant Likely
61c7a080a5 of: Always use 'struct device.of_node' to get device node pointer.
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated.  This patch
makes all readers of these elements use device.of_node instead.

(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-05-18 16:10:44 -06:00
Dan Williams
0b28330e39 Merge branch 'ioat' into dmaengine 2010-05-17 16:30:58 -07:00
Linus Walleij
058276303d DMAENGINE: extend the control command to include an arg
This adds an argument to the DMAengine control function, so that
we can later provide control commands that need some external data
passed in through an argument akin to the ioctl() operation
prototype.

[dan.j.williams@intel.com: fix up some missed conversions]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2010-05-17 16:30:42 -07:00
Russell King
ac1d426e82 Merge branch 'devel-stable' into devel
Conflicts:
	arch/arm/Kconfig
	arch/arm/include/asm/system.h
	arch/arm/mm/Kconfig
2010-05-17 17:24:04 +01:00
Valentin Longchamp
1c5250d616 serial: imx.c: fix CTS trigger level lower to avoid lost chars
The imx CTS trigger level is left at its reset value that is 32
chars. Since the RX FIFO has 32 entries, when CTS is raised, the
FIFO already is full. However, some serial port devices first empty
their TX FIFO before stopping when CTS is raised, resulting in lost
chars.

This patch sets the trigger level lower so that other chars arrive
after CTS is raised, there is still room for 16 of them.

Signed-off-by: Valentin Longchamp<valentin.longchamp@epfl.ch>
Tested-by: Philippe Rétornaz<philippe.retornaz@epfl.ch>
Acked-by: Wolfram Sang<w.sang@pengutronix.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-13 12:10:56 -07:00
Anatolij Gustschin
e6114fa1d1 serial: mpc52xx_uart: fix null pointer dereference
Commit 6acc683351
introduced NULL pointer dereference and kernel crash
on ppc32 machines while booting. Fix this bug now.

Reported-by: Leonardo Chiquitto <leonardo.lists@gmail.com>
Tested-by: Leonardo Chiquitto <leonardo.lists@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-05-13 12:10:55 -07:00
Dominik Brodowski
317b6d6300 pcmcia: dev_node removal (write-only drivers)
dev_node_t was only used to transport some minor/major numbers
from the PCMCIA device drivers to deprecated userspace helpers.
However, only a few drivers made use of it, and the userspace
helpers are deprecated anyways. Therefore, get rid of dev_node_t .

As a first step, remove any usage of dev_node_t from drivers which
only wrote to this typedef/struct, but did not make use of it.

CC: linux-bluetooth@vger.kernel.org
CC: Harald Welte <laforge@gnumonks.org>
CC: linux-mtd@lists.infradead.org
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-05-10 10:23:14 +02:00
Dominik Brodowski
eb14120f74 pcmcia: re-work pcmcia_request_irq()
Instead of the old pcmcia_request_irq() interface, drivers may now
choose between:

- calling request_irq/free_irq directly. Use the IRQ from *p_dev->irq.

- use pcmcia_request_irq(p_dev, handler_t); the PCMCIA core will
  clean up automatically on calls to pcmcia_disable_device() or
  device ejection.

- drivers still not capable of IRQF_SHARED (or not telling us so) may
  use the deprecated pcmcia_request_exclusive_irq() for the time
  being; they might receive a shared IRQ nonetheless.

CC: linux-bluetooth@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: linux-usb@vger.kernel.org
CC: linux-ide@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-05-10 10:23:13 +02:00
Benjamin Herrenschmidt
1ed31d6db9 Merge commit 'origin/master' into next 2010-05-07 11:29:25 +10:00
Yauhen Kharuzhy
4fcfce9f33 serial: Use s3c2440 driver for S3C2416 SoC
UARTs in the S3C2416 are almost same as in S3C2443 and can be handled by
s3c2440 serial driver.

Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-05-06 11:37:18 +09:00
Claudio Scordino
e8faff7330 ARM: 6092/1: atmel_serial: support for RS485 communications
Final version of the patch that adds support for RS485 communications to the atmel_serial driver.

The patch has been already sent and discussed on both linux-kernel and linux-arm-kernel mailing lists several times.

Many people collaborated to improve and test the code:

Tested-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Tested-by: Bernhard Roth <br@pwrnet.de>
Reviewed-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Rick Bronson <rick@efn.org>
Signed-off-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-05-04 16:59:11 +01:00
Linus Torvalds
87156d692a Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: drivers/serial/pmac_zilog.c: add missing unlock
  serial: 8250_pnp - add Fujitsu Wacom device
  tty: Fix regressions in the char driver conversion
2010-04-30 10:16:42 -07:00
Linus Torvalds
8f2adb7cab Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
  spi: spidev_test gives error upon 1-byte transfer
  omap2_mcspi: small fixes of output data format
  omap2_mcspi: Flush posted writes
  spi: spi_device memory should be released instead of device.
  spi: release device claimed by bus_find_device_by_name
  of: check for IS_ERR()
  serial/mpc52xx_uart: Drop outdated comments
  gpio: potential null dereference
2010-04-30 09:57:55 -07:00
Julia Lawall
c61fae964a serial: drivers/serial/pmac_zilog.c: add missing unlock
In an error handling case the lock is not unlocked.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E1;
identifier f;
@@

f (...) { <+...
* spin_lock_irqsave (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-30 09:20:34 -07:00
Ping Cheng
d9901660b5 serial: 8250_pnp - add Fujitsu Wacom device
Add Fujitsu Wacom 1FGT Tablet PC device

Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-30 09:20:34 -07:00
Linus Torvalds
6bec11921a Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
  ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
  ARM: 6030/1: KS8695: enable console
  ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
  ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
  ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
  ARM: fix build error in arch/arm/kernel/process.c
2010-04-29 17:17:35 -07:00
Wolfram Sang
b0c06027c7 serial/mpc52xx_uart: Drop outdated comments
Most things mentioned are either obsolete (platform-support) or wrong (device
numbering, DCD spport) these days. The remaining rest is obvious.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-04-28 00:54:58 -06:00
Paul Mundt
e19553427c Merge branch 'sh/stable-updates'
Conflicts:
	arch/sh/kernel/dwarf.c
	drivers/dma/shdma.c

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-04-26 16:08:27 +09:00
Yegor Yefremov
0ad707407d ARM: 6030/1: KS8695: enable console
Add add_preferred_console() to ks8695_console_init() to
enable the console

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-04-23 10:01:56 +01:00
Philippe De Muyter
2545cf6e94 m68knommu: allow 4 coldfire serial ports
Fix driver/serial/mcf.c for 4-ports coldfire's (e.g. MCF5484).

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-04-21 14:56:00 +10:00
Philippe De Muyter
3732b68f22 m68knommu: fix coldfire tcdrain
Fix tcdrain on coldfire uarts.
Currently with coldfire uarts tcdrain returns without waiting for txempty,
because (tx)fifosize is 0.  Fix that and call uart_update_timeout when
setting the baud rate, otherwise tcdrain will wait for an half our :)
Also constify mcf_uart_ops.

Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2010-04-21 13:43:06 +10:00
Timur Maximov
6f4567c8cf serial_cs: MD55x support (PCMCIA GPRS/EDGE modem) (kernel 2.6.33)
Many PCMCIA GPRS modems like: Onda Edge N100E, Novaway PC98 (OEM SPC98Z),
Rovermate Edgus Adaptmate-039 and others have same construction and
identification:

lspcmcia -vvv
Product Name:   Generic Modem: MD55x 1.00 Serial number: xxxxx-xxx
Identification: manf_id: 0x015d card_id: 0x4c45
                function: 2 (serial)
                prod_id(1): "Generic" (0xc49e4731)
                prod_id(2): "Modem: MD55x" (0x8913b110)
                prod_id(3): "1.00" (0x83dbf271)
                prod_id(4): "Serial number: xxxxx-xxx" (0x73ee9514)

Serial connection to GSM module based on Elan VPU16551 PCMCIA UART with
datasheet recommeded 14.7456MHz crystal oscillator.

By default serial_cs set UART clock == 1843200 Hz
For correct work need set clock 14745600 Hz.
This quirk already present in driver, only need add device in quirk list.

Signed-off-by: Timur Maximov <xcom.org@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-04-17 17:53:32 +02:00
Corey Minyard
f467bc148d powerpc/mpsc: Set the port device in the mpsc serial driver
The mpsc serial driver needx to set the port's device tree element
to register properly.

Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2010-04-07 14:12:36 +10:00
Paul Mundt
94a46d3cde Merge branch 'sh/stable-updates' 2010-04-05 12:21:09 +09:00
Tejun Heo
336f5899d2 Merge branch 'master' into export-slabh 2010-04-05 11:37:28 +09:00
David S. Miller
87e8b821ed Merge branch 'master' of /home/davem/src/GIT/linux-2.6/ 2010-04-03 15:49:14 -07:00
Tejun Heo
5a0e3ad6af include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.

Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-30 22:02:32 +09:00
Julia Lawall
c4a3987fa0 drivers/serial/sunsu.c: Correct use after free
The of_iounmap is at the out_unmap label, but at that point up has already
been freed.  The free cannot be moved to the out_unmap label, because that
label is reachable from cases where up should not be freed.  So the call to
of_iounmap is just duplicated, and the goto converted to a return.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,e;
identifier f;
iterator I;
statement S;
@@

*kfree(x);
... when != &x
    when != x = e
    when != I(x,...) S
*x->f
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-29 22:33:28 -07:00
Paul Mundt
720fcb36ac Merge branches 'sh/intc-extension', 'sh/dmaengine', 'sh/serial-dma' and 'sh/clkfwk'
Conflicts:
	arch/sh/kernel/cpu/clock.c

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-30 11:26:43 +09:00
Linus Torvalds
6631424fd2 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
  r8169: offical fix for CVE-2009-4537 (overlength frame DMAs)
  ipv6: Don't drop cache route entry unless timer actually expired.
  tulip: Add missing parens.
  r8169: fix broken register writes
  pcnet_cs: add new id
  bonding: fix broken multicast with round-robin mode
  drivers/net: Fix continuation lines
  e1000: do not modify tx_queue_len on link speed change
  net: ipmr/ip6mr: prevent out-of-bounds vif_table access
  ixgbe: Do not run all Diagnostic offline tests when VFs are active
  igb: use correct bits to identify if managability is enabled
  benet: Fix compile warnnings in drivers/net/benet/be_ethtool.c
  net: Add MSG_WAITFORONE flag to recvmmsg
  e1000e: do not modify tx_queue_len on link speed change
  igbvf: do not modify tx_queue_len on link speed change
  ipv4: Restart rt_intern_hash after emergency rebuild (v2)
  ipv4: Cleanup struct net dereference in rt_intern_hash
  net: fix netlink address dumping in IPv4/IPv6
  tulip: Fix null dereference in uli526x_rx_packet()
  gianfar: fix undo of reserve()
  ...
2010-03-29 14:41:18 -07:00
Ken Kawasaki
1546a713ae pcnet_cs: add new id
pcnet_cs:
 *add new id (Allied Telesis LM33-PCM-T Lan&Modem multifunction card)
 *use PROD_ID for LA-PCM.(because LA-PCM and LM33-PCM-T use the same MANF_ID).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-27 16:41:28 -07:00
Linus Walleij
c3635c78e5 DMAENGINE: generic slave control v2
Convert the device_terminate_all() operation on the
DMA engine to a generic device_control() operation
which can now optionally support also pausing and
resuming DMA on a certain channel. Implemented for the
COH 901 318 DMAC as an example.

[dan.j.williams@intel.com: update for timberdale]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Li Yang <leoli@freescale.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Magnus Damm <damm@opensource.se>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Joe Perches <joe@perches.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2010-03-26 16:44:01 -07:00
Guennadi Liakhovetski
3089f381fb SH: extend SCI DMA support to work on SCIFA ports
SCIFA ports have additional bits to control DMA requests and they must have
respective interrupt sources enabled, as the datasheet suggests, the only way
to avoid actually taking interrupts in addition to DMA events is by masking the
IRQ on the CPU.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23 17:39:30 +09:00
Magnus Damm
f354a38175 serial: sh-sci: Use sg_dma_len() and sg_dma_address()
Convert the dmaengine code in sh-sci.c from
directly accessing the struct scatterlist members
length, dma_length and dma_address to using the
macros sg_dma_len() and sg_dma_address().

Makes the code build for ARM.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23 17:19:50 +09:00
Magnus Damm
4bab9d426e dmaengine: shdma: Remove sh_dmae_slave_chan_id enum
This patch replaces the sh_dmae_slave_chan_id enum
with an unsigned int. The purpose of this chainge is
to make it possible to separate the slave id enums
from the dmaengine header.

The slave id enums varies with processor model, so in
the future it makes sense to put these in the processor
specific headers together with the pinmux enums.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23 17:19:30 +09:00
Guennadi Liakhovetski
0a60a210ed SH: remove superfluous warning from the serial driver
This warning has been introduced during the SCI DMA support developmenr and is
not needed any more.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23 13:33:51 +09:00
Guennadi Liakhovetski
d7bbf7f50e SH: fix SCIFA SCASCR register bit definitions
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23 13:33:45 +09:00
Magnus Damm
8d099d4446 serial: sh-sci: fix SH-Mobile SH breakage
The follwing commit breaks SH-Mobile on non-ARM platforms:
"8a77b8d serial: sh-sci: Support ARM-based SH-Mobile CPUs."

The commit assumed that CONFIG_ARCH_SHMOBILE only was set
on ARM platforms, but it turns out that this kconfig is also
set by all SH-based SoCs. Sh7724 and other older SH-Mobile
SoCs are all broken without this fix.

This patch converts the "defined(CONFIG_ARCH_SHMOBILE)" into
one "defined()" per SoC model - similar to existing SH code.

Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-23 13:23:15 +09:00
Linus Torvalds
e4d806377b Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  serial: sh-sci: remove duplicated #include
  sh: Export uncached helper symbols.
  sh: Fix up NUMA build for 29-bit.
  serial: sh-sci: Fix build failure for non-sh architectures.
  sh: Fix up uncached offset for legacy 29-bit mode.
  sh: Support CPU affinity masks for INTC controllers.
2010-03-19 18:16:20 -07:00
Linus Torvalds
8dba8f9494 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  tty_port,usb-console: Fix usb serial console open/close regression
  tty: cpm_uart: use resource_size()
  tty_buffer: Fix distinct type warning
  hvc_console: Fix race between hvc_close and hvc_remove
  uartlite: Fix build on sparc.
  tty: Take a 256 byte padding into account when buffering below sub-page units
  Revert "tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call"
2010-03-19 13:40:03 -07:00
Tobias Klauser
2314436658 tty: cpm_uart: use resource_size()
Use the resource_size function instead of manually calculating the
resource size.  This reduces the chance of introducing off-by-one errors.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19 07:17:56 -07:00
David Miller
f157b58511 uartlite: Fix build on sparc.
We can get this driver enabled via MFD_TIMBERDALE which only
requires GPIO to be on.

But the of_address_to_resource() function is only present on
powerpc and microblaze, so we have to conditionalize the
CONFIG_OF probing bits on that.

Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-19 07:17:54 -07:00
Linus Torvalds
9d20593a72 Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
  powerpc/5200: Build fix for mpc52xx watchdog timer code
  of: Fix comparison of "compatible" properties
  powerpc/52xx: update defconfigs
  spi/omap2_mcspi: Use transaction speed if provided
  spi/omap2_mcspi: fix NULL pointer dereference
  uartlite: Fix build on sparc.
2010-03-18 17:01:19 -07:00
Linus Torvalds
7de4a9a735 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sunxvr1000: Add missing FB=y depenency.
  MAINTAINERS: Add entry for sparc serial drivers.
  drivers/serial/sunsab.c: adjust the constant used to initialize the interrupt_mask0 fields
2010-03-18 16:44:47 -07:00
Julia Lawall
935050daad drivers/serial/sunsab.c: adjust the constant used to initialize the interrupt_mask0 fields
From: Julia Lawall <julia@diku.dk>

SAB82532_ISR0_TCD is declared in drivers/serial/subsab.h as relating to a
status register, while SAB82532_IMR0_TCD is declared in the same file as
relating to a mask register.  The latter seems more appropriate for the
interrupt_mask0 field, and follows the strategy for initializing this field
elsewhere in the same file.

Both SAB82532_ISR0_TCD and SAB82532_IMR0_TCD have the same value.

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-03-16 00:33:37 -07:00
Huang Weiyi
3f7581d66e serial: sh-sci: remove duplicated #include
Remove duplicated #include('s) in
  drivers/serial/sh-sci.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-15 12:25:13 +09:00
Linus Torvalds
c32da02342 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
  doc: fix typo in comment explaining rb_tree usage
  Remove fs/ntfs/ChangeLog
  doc: fix console doc typo
  doc: cpuset: Update the cpuset flag file
  Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
  Remove drivers/parport/ChangeLog
  Remove drivers/char/ChangeLog
  doc: typo - Table 1-2 should refer to "status", not "statm"
  tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
  No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
  devres/irq: Fix devm_irq_match comment
  Remove reference to kthread_create_on_cpu
  tree-wide: Assorted spelling fixes
  tree-wide: fix 'lenght' typo in comments and code
  drm/kms: fix spelling in error message
  doc: capitalization and other minor fixes in pnp doc
  devres: typo fix s/dev/devm/
  Remove redundant trailing semicolons from macros
  fix typo "definetly" -> "definitely" in comment
  tree-wide: s/widht/width/g typo in comments
  ...

Fix trivial conflict in Documentation/laptops/00-INDEX
2010-03-12 16:04:50 -08:00
Linus Torvalds
dca1d9f6d7 Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (370 commits)
  ARM: S3C2443: Add set_rate and round_rate calls for armdiv clock
  ARM: S3C2443: Remove #if 0 for clk_mpll
  ARM: S3C2443: Update notes on MPLLREF clock
  ARM: S3C2443: Further clksrc-clk conversions
  ARM: S3C2443: Change to using plat-samsung clksrc-clk implementation
  USB: Fix s3c-hsotg build following Samsung platform header moves
  ARM: S3C64XX: Reintroduce unconditional build of audio device
  ARM: 5961/1: ux500: fix CLKRST addresses
  ARM: 5977/1: arm: Enable backtrace printing on oops when PC is corrupted
  ASoC: Fix S3C64xx IIS driver for Samsung header reorg
  ARM: S3C2440: Fix plat-s3c24xx move of s3c2440/s3c2442 support
  [ARM] pxa: fix typo in mxm8x10.h
  [ARM] pxa/raumfeld: set GPIO drive bits for LED pins
  [ARM] pxa/zeus: Add support for mcp2515 CAN bus
  [ARM] pxa/zeus: Add support for onboard max6369 watchdog
  [ARM] pxa/zeus: Add Eurotech as the manufacturer
  [ARM] pxa/zeus: Correct the USB host initialisation flags
  [ARM] pxa/zeus: Allow usage of 8250-compatible UART in uncompress
  [ARM] pxa: refactor uncompress.h for non-PXA uarts
  [ARM] mmp2: fix incorrect calling of chip->mask_ack() for 2nd level cascaded IRQs
  ...
2010-03-12 16:00:54 -08:00
Rodolfo Giometti
7ed63d5eb4 serial amba-pl010: enable PPS support
Function pl010_enable_ms() is automagically called when PPS ldisc
is selected.

Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:43 -08:00
Rodolfo Giometti
dc77f161aa serial 8250: enable PPS support
Automagically function serial8250_enable_ms() is called when PPS ldisc
is selected.

Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Alexander Gordeev <lasaine@lvk.cs.msu.su>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-12 15:52:43 -08:00
David Miller
07081fd858 uartlite: Fix build on sparc.
We can get this driver enabled via MFD_TIMBERDALE which only
requires GPIO to be on.

But the of_address_to_resource() function is only present on
powerpc and microblaze, so we have to conditionalize the
CONFIG_OF probing bits on that.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-03-10 14:10:41 -07:00
Paul Mundt
c7ed1ab3f7 serial: sh-sci: clkdev updates for MSTP gating.
This fixes up some of the I/D/F clock ambiguity in the sh-sci driver.
The interface clock in most cases just wraps back to the peripheral
clock, while the function clock wraps in to the MSTP bits. As the logic
was somewhat inverted, this cleans that up, and also enables all CPUs
with SCI MSTP bits to match function clocks through clkdev lookup.

As a result, this gets rid of the clk string abuse on the sh side, and
the clock string will be killed off once the ARM code has had a chance to
sync up. This also enables MSTP gating on CPUs like 7786 which had never
wired it up before. Impacted CPUs are primarily all SH-Mobiles, SH7785,
and SH7786.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-10 18:35:14 +09:00
Russell King
988addf82e Merge branch 'origin' into devel-stable
Conflicts:
	arch/arm/mach-mx2/devices.c
	arch/arm/mach-mx2/devices.h
	sound/soc/pxa/pxa-ssp.c
2010-03-08 20:21:04 +00:00
Jiri Kosina
318ae2edc3 Merge branch 'for-next' into for-linus
Conflicts:
	Documentation/filesystems/proc.txt
	arch/arm/mach-u300/include/mach/debug-macro.S
	drivers/net/qlge/qlge_ethtool.c
	drivers/net/qlge/qlge_main.c
	drivers/net/typhoon.c
2010-03-08 16:55:37 +01:00
Linus Torvalds
4a31c08d2f Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
  sh: Convert sh to use read/update_persistent_clock
  sh: Move PMB debugfs entry initialization to later stage
  sh: Fix up flush_cache_vmap() on SMP.
  sh: fix up MMU reset with variable PMB mapping sizes.
  sh: establish PMB mappings for NUMA nodes.
  sh: check for existing mappings for bolted PMB entries.
  sh: fixed virt/phys mapping helpers for PMB.
  sh: make pmb iomapping configurable.
  sh: reworked dynamic PMB mapping.
  sh: Fix up cpumask_of_pcibus() for the NUMA build.
  serial: sh-sci: Tidy up build warnings.
  sh: Fix up ctrl_read/write stragglers in migor setup.
  serial: sh-sci: Add DMA support.
  dmaengine: shdma: extend .device_terminate_all() to record partial transfer
  sh: merge sh7722 and sh7724 DMA register definitions
  sh: activate runtime PM for dmaengine on sh7722 and sh7724
  dmaengine: shdma: add runtime PM support.
  dmaengine: shdma: separate DMA headers.
  dmaengine: shdma: convert to platform device resources
  dmaengine: shdma: fix DMA error handling.
  ...
2010-03-07 15:47:19 -08:00
Russell King
882d01f96b Merge branch 'for-rmk/samsung5' of git://git.fluff.org/bjdooks/linux into devel-stable
Conflicts:
	arch/arm/Kconfig
	arch/arm/Makefile
2010-03-02 23:40:15 +00:00
Russell King
64ed28a87a Merge master.kernel.org:/pub/scm/linux/kernel/git/lethal/genesis-2.6 into devel-stable
Conflicts:
	arch/arm/Kconfig
2010-03-02 23:31:07 +00:00
Russell King
b93a4afcff Merge branch 'for-rmk' of git://git.pengutronix.de/git/imx/linux-2.6 into devel-stable
Conflicts:
	arch/arm/Makefile
2010-03-02 23:29:32 +00:00
Breno Leitao
137ee2f5d1 jsm: fixing error if the driver fails to load
Currently if the driver fails to register on port, the kernel
crashes with the following stack:

cpu 0x1: Vector: 300 (Data Access) at [c0000000e0303090]
    pc: c00000000039aa74: .__mutex_lock_slowpath+0x44/0x10c
    lr: c00000000039aa58: .__mutex_lock_slowpath+0x28/0x10c
[c0000000e03033c0] c00000000026b074 .uart_remove_one_port+0xbc/0x16c
[c0000000e0303460] d0000000000e0554 .jsm_remove_uart_port+0x8c/0x10c [jsm]
[c0000000e03034f0] d0000000000dc034 .jsm_remove_one+0x34/0x108 [jsm]
[c0000000e0303590] c0000000001f4aa0 .pci_device_remove+0x48/0x74
...

This patch just fixes the code flow to abort the load when an
error is detected.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:24 -08:00
Breno Leitao
54862ee005 jsm: removing the uart structure and filename on error
If jsm fails to load, then remove the uart stuff, otherwise,
the things (as files), will be there forever (even when the module
is unloaded). If you try to reload the module, the following message
appears:

kobject_add_internal failed for ttyn1 with -EEXIST, don't try to
register things with the same name in the same directory.

This patch remove the uart things when the driver fails.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:24 -08:00
Alan Cox
4165fe4ef7 tty: Fix up char drivers request_room usage
We can't change them all but quite a few misuse it.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:22 -08:00
Alan Cox
97c22394bb serial: timberdale: Remove dependancies
MFD_TIMBERDALE doesn't appear to be defined anywhere. However the code in
question can build happily without platform specifics so remove the check

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:21 -08:00
Maxime Bizon
6a2c7eabfd serial: bcm63xx_uart: allow more than one uart to be registered.
The bcm6358 CPU has two uarts, make it possible to use the second one.

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:19 -08:00
Maxime Bizon
a6d07d14bb serial: bcm63xx_uart: don't use kfree() on non kmalloced area.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:18 -08:00
Mike Frysinger
599b714ce1 serial: bfin_5xx: pull in linux/io.h for ioremap prototypes
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:18 -08:00
Sonic Zhang
cdc592d5d4 serial: bfin_5xx: kgdboc should accept gdb break only when it is active
If we always check for gdb breaks even when it isn't active, we get false
positives on normal code and the system panics.

URL: http://blackfin.uclinux.org/gf/tracker/5277

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:17 -08:00
Graf Yang
7ed43f6af8 serial: bfin_5xx: need to disable DMA TX interrupt too
If we don't disable the DMA TX channel, an inopportune timeout will
trigger the interrupt handler and may cause a dead lock with the spin_lock.

Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:17 -08:00
Sonic Zhang
b2ced4f69e serial: bfin_5xx: remove useless gpio handling with hard flow control
For UARTs that have dedicated hardware flow control support, there will be
no gpios to request/free as they are part of the normal peripheral pins.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:16 -08:00
Ben Hutchings
e6c4ef984e tty: declare MODULE_FIRMWARE in various drivers
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:15 -08:00
Roel Kluin
1e091751cd serial: fix test of unsigned
The variables were unsigned so the tests did not work.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:11 -08:00
Kiros Yeh
2a52fcb54f serial: add support for Korenix JetCard
Add different model (with a different PCI ID) to support Korenix JetCard.

Signed-off-by: Kiros Yeh <kiros@korenix.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:10 -08:00
Baruch Siach
bbcd18d1b3 serial: imx: fix NULL dereference Oops when pdata == NULL
The platform code doesn't have to provide platform data to get sensible
default behaviour from the imx serial driver.

This patch does not handle NULL dereference in the IrDA case, which still
requires a valid platform data pointer (in imx_startup()/imx_shutdown()),
since I don't know whether there is a sensible default behaviour, or
should the operation just fail cleanly.

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oskar Schirmer <os@emlix.com>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:10 -08:00
Ira W. Snyder
ac6ec5b1de serial: 8250_pci: add support for MCS9865 / SYBA 6x Serial Port Card
This patch is heavily based on an earlier patch found on the linux-serial
mailing list [1], written by Darius Augulis.

The previous incarnation of this patch only supported a 2x serial port
card.  I have added support for my SYBA 6x serial port card, and tested on
x86.

[1]: http://marc.info/?l=linux-serial&m=124975806304760

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:08 -08:00
Albin Tonnerre
8fe2d54145 serial: atmel_serial: add poll_get_char and poll_put_char uart_ops
Permits using KGDB over the console with the atmel_serial driver.

[akpm@linux-foundation.org: s/barrier/cpu_relax/]
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:08 -08:00
Thiago Farina
8b505ca8e2 serial: 68328serial.c: remove BAUD_TABLE_SIZE macro
This macro is a duplicate of ARRAY_SIZE defined in kernel api, so just use
that instead.

Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:07 -08:00
Shmulik Ladkani
b5d228cc4f serial: copy UART properties of UPF_FIXED_TYPE ports provisioned using early_serial_setup
Augment the UPF_FIXED_TYPE logic, which currently applies to UART ports
provisioned using platform_device_register.

The suggested patch applies same logic into 'serial8250_register_ports',
making UART ports provisioned using early_serial_setup inherit their
properties from the uart_config entry.

Signed-off-by: Shmulik Ladkani <shmulik@jungo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:07 -08:00
sonic zhang
ccf68e59e9 serial: fit blackfin uart over sport driver into common uart infrastructure
Fit blackfin uart over sport driver into common uart inftrastructure.  It
is based on the early platform interfaces to get the platform data early
when the console is initilized.

1. Enable sport uart driver to change uart baud, data bit, stop bit at
   runtime.  Bind the index of uart device nodes to physical index of
   sports.

2. Move all platform data into arch specific board files.  Register
   and probe platform device data in both early and normal stages.

3. Console is registered in sport uart driver as well.

4. Remove 500 us block waiting in sport tx stop code by putting a
   dummy data into tx fifo to make sure the sport tx stops when all bytes
   are shifted out except for the dummy data.

5. clean up a bit and fix up coding style.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:43:06 -08:00
Paul Mundt
c6efd46b98 serial: sh-sci: Tidy up build warnings.
The recent sh-sci DMA support introduces a number of trivial build
warnings, clean them up.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-02 11:53:54 +09:00
Guennadi Liakhovetski
73a19e4c03 serial: sh-sci: Add DMA support.
Support using DMA for sending and receiving data over SCI(F) interfaces of
various SH SoCs.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-03-02 11:39:15 +09:00
Linus Torvalds
ac0f6f927d Merge branch 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (100 commits)
  ARM: Eliminate decompressor -Dstatic= PIC hack
  ARM: 5958/1: ARM: U300: fix inverted clk round rate
  ARM: 5956/1: misplaced parentheses
  ARM: 5955/1: ep93xx: move timer defines into core.c and document
  ARM: 5954/1: ep93xx: move gpio interrupt support to gpio.c
  ARM: 5953/1: ep93xx: fix broken build of clock.c
  ARM: 5952/1: ARM: MM: Add ARM_L1_CACHE_SHIFT_6 for handle inside each ARCH Kconfig
  ARM: 5949/1: NUC900 add gpio virtual memory map
  ARM: 5948/1: Enable timer0 to time4 clock support for nuc910
  ARM: 5940/2: ARM: MMCI: remove custom DBG macro and printk
  ARM: make_coherent(): fix problems with highpte, part 2
  MM: Pass a PTE pointer to update_mmu_cache() rather than the PTE itself
  ARM: 5945/1: ep93xx: include correct irq.h in core.c
  ARM: 5933/1: amba-pl011: support hardware flow control
  ARM: 5930/1: Add PKMAP area description to memory.txt.
  ARM: 5929/1: Add checks to detect overlap of memory regions.
  ARM: 5928/1: Change type of VMALLOC_END to unsigned long.
  ARM: 5927/1: Make delimiters of DMA area globally visibly.
  ARM: 5926/1: Add "Virtual kernel memory..." printout.
  ARM: 5920/1: OMAP4: Enable L2 Cache
  ...

Fix up trivial conflict in arch/arm/mach-mx25/clock.c
2010-03-01 09:15:15 -08:00
Linus Torvalds
847f9c606c Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (24 commits)
  m68k: Define sigcontext ABI of ColdFire
  m68knommu: NPTL support for uClinux
  m68k: Add NPTL support
  m68k: Eliminate unused variable in page_to_phys()
  m68k: Switch to generic siginfo layout
  macfb: fix 24-bit visual and stuff
  macfb: cleanup
  fbdev: add some missing mac modes
  mac68k: start CUDA early
  valkyriefb: various fixes
  fbdev: mac_var_to_mode() fix
  mac68k: move macsonic and macmace platform devices
  mac68k: move mac_esp platform device
  mac68k: replace mac68k SCC code with platform device
  pmac-zilog: add platform driver
  pmac-zilog: cleanup
  mac68k: rework SWIM platform device
  mac68k: cleanup
  ataflop: Killl warning about unused variable flags
  m68k: Use DIV_ROUND_CLOSEST
  ...
2010-02-27 16:22:47 -08:00
Linus Torvalds
f1dd6ad599 Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (141 commits)
  MIPS: Alchemy: defconfig updates
  MIPS: Alchemy: Fix Au1100 ethernet build failure
  MIPS: Alchemy: Repair db1500/bosporus builds
  MIPS: ARC: Cleanup unused definitions from sgialib.h
  MIPS: Cobalt: convert legacy port addresses to GT-64111 bus addresses
  MIPS: Alchemy: use 36bit addresses for PCMCIA resources.
  MIPS: Cobalt: Fix theoretical port aliasing issue
  MIPS: Use ALIGN(x, bytes) instead of __ALIGN_MASK(x, bytes - 1)
  MIPS: Crazy spinlock speed test.
  MIPS: Optimize spinlocks.
  MIPS: Alchemy: devboard PM needs to save CPLD registers.
  MIPS: PowerTV: Eliminate duplicate opcode definition macros
  MIPS: Lemote 2F: Move printks out of port_access_lock.
  MIPS: PNX833x: Convert IRQ controller locks to raw spinlocks.
  MIPS: Octeon: Replace spinlock with raw_spinlocks in dma-octeon.c.
  MIPS: Octeon: Replace rwlocks in irq_chip handlers with raw_spinlocks.
  MIPS: Octeon: Convert octeon_irq_msi_lock to raw spinlock.
  MIPS: Loongson: Remove pointless sample_lock from oprofile code.
  MIPS: SNI: Convert sni_rm200_i8259A_lock to raw spinlock.
  MIPS: i8259: Convert IRQ controller lock to raw spinlock.
  ...
2010-02-27 16:19:22 -08:00
Linus Torvalds
8d37a371b6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (49 commits)
  pcmcia: validate late-added resources
  pcmcia: allow for extension of resource interval
  pcmcia: remove useless msleep in ds.c
  pcmcia: use read_cis_mem return value
  pcmcia: handle error in serial_cs config calls
  pcmcia: add locking to pcmcia_{read,write}_cis_mem
  pcmcia: avoid prod_id memleak
  pcmcia: avoid sysfs-related lockup for cardbus
  pcmcia: use state machine for extended requery
  pcmcia: delay re-scanning and re-querying of PCMCIA bus
  pcmcia: use pccardd to handle eject, insert, suspend and resume requests
  pcmcia: use ops_mutex for rsrc_{mgr,nonstatic} locking
  pcmcia: use mutex for dynid lock
  pcmcia: assert locking to struct pcmcia_device
  pcmcia: add locking documentation
  pcmcia: simplify locking
  pcmcia: add locking to struct pcmcia_socket->pcmcia_state()
  pcmcia: protect s->device_count
  pcmcia: properly lock skt->irq, skt->irq_mask
  pcmcia: lock ops->set_socket
  ...
2010-02-27 16:18:30 -08:00
Linus Torvalds
ef1a8de8ea Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (88 commits)
  powerpc: Fix lwsync feature fixup vs. modules on 64-bit
  powerpc: Convert pmc_owner_lock to raw_spinlock
  powerpc: Convert die.lock to raw_spinlock
  powerpc: Convert tlbivax_lock to raw_spinlock
  powerpc: Convert mpic locks to raw_spinlock
  powerpc: Convert pmac_pic_lock to raw_spinlock
  powerpc: Convert big_irq_lock to raw_spinlock
  powerpc: Convert feature_lock to raw_spinlock
  powerpc: Convert i8259_lock to raw_spinlock
  powerpc: Convert beat_htab_lock to raw_spinlock
  powerpc: Convert confirm_error_lock to raw_spinlock
  powerpc: Convert ipic_lock to raw_spinlock
  powerpc: Convert native_tlbie_lock to raw_spinlock
  powerpc: Convert beatic_irq_mask_lock to raw_spinlock
  powerpc: Convert nv_lock to raw_spinlock
  powerpc: Convert context_lock to raw_spinlock
  powerpc/85xx: Add NOR, LEDs and PIB support for MPC8568E-MDS boards
  powerpc/86xx: Enable VME driver on the GE SBC610
  powerpc/86xx: Enable VME driver on the GE PPC9A
  powerpc/86xx: Add MSI section to GE PPC9A DTS
  ...
2010-02-27 13:26:18 -08:00
Finn Thain
ec9cbe0989 pmac-zilog: add platform driver
Add platform driver support to the pmac-zilog driver, for m68k macs.
Place the powermac-specific code inside #ifdef CONFIG_PPC_PMAC.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2010-02-27 18:31:02 +01:00
Finn Thain
1f7b5fff50 pmac-zilog: cleanup
Whitespace cleanups and comment typo fix.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2010-02-27 18:28:37 +01:00
Manuel Lauss
b2b13cdfd0 SERIAL 8250: Fixes for Alchemy UARTs.
Limit the amount of address space claimed for Alchemy serial ports to
0x1000.  On the Au1300, ports are only 0x1000 apart, and the registers
only extend to 0x110 at most on all supported alchemy models.

On the Au1300 the autodetect logic no longer works and this makes it
necessary to specify the port type through platform data.  Because of
this the MSR quirk needs to be moved outside the autoconfig() function
which will no longer be called when UPF_FIXED_TYPE is specified.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-02-27 12:52:57 +01:00
Linus Torvalds
64d497f553 Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (187 commits)
  sh: remove dead LED code for migo-r and ms7724se
  sh: ecovec build fix for CONFIG_I2C=n
  sh: ecovec r-standby support
  sh: ms7724se r-standby support
  sh: SH-Mobile R-standby register save/restore
  clocksource: Fix up a registration/IRQ race in the sh drivers.
  sh: ms7724: modify scan_timing for KEYSC
  sh: ms7724: Add sh_sir support
  sh: mach-ecovec24: Add sh_sir support
  sh: wire up SET/GET_UNALIGN_CTL.
  sh: allow alignment fault mode to be configured at kernel boot.
  sh: sh7724: Update FSI/SPU2 clock
  sh: always enable sh7724 vpu_clk and set to 166MHz on Ecovec
  sh: add sh7724 kick callback to clk_div4_table
  sh: introduce struct clk_div4_table
  sh: clock-cpg div4 set_rate() shift fix
  sh: Turn on speculative return for SH7785 and SH7786
  sh: Merge legacy and dynamic PMB modes.
  sh: Use uncached I/O helpers in PMB setup.
  sh: Provide uncached I/O helpers.
  ...
2010-02-26 16:54:27 -08:00
Benjamin Herrenschmidt
874f2f997d Merge commit 'origin/master' into next
Manual merge of:
	drivers/char/hvc_console.c
	drivers/char/hvc_console.h
2010-02-26 14:41:00 +11:00
Linus Torvalds
6ebdc661b6 Merge branch 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (41 commits)
  of: remove undefined request_OF_resource & release_OF_resource
  of/sparc: Remove sparc-local declaration of allnodes and devtree_lock
  of: move definition of of_chosen into common code.
  of: remove unused extern reference to devtree_lock
  of: put default string compare and #a/s-cell values into common header
  of/flattree: Don't assume HAVE_LMB
  of: protect linux/of.h with CONFIG_OF
  proc_devtree: fix THIS_MODULE without module.h
  of: Remove old and misplaced function declarations
  of/flattree: Make the kernel accept ePAPR style phandle information
  of/flattree: endian-convert members of boot_param_header
  of: assume big-endian properties, adding conversions where necessary
  of: use __be32 for cell value accessors
  of/flattree: use OF_ROOT_NODE_{SIZE,ADDR}_CELLS DEFAULT for fdt parsing
  of/flattree: use callback to setup initrd from /chosen
  proc_devtree: include linux/of.h
  of: make set_node_proc_entry private to proc_devtree.c
  of: include linux/proc_fs.h
  of/flattree: merge early_init_dt_scan_memory() common code
  of: add 'of_' prefix to machine_is_compatible()
  ...
2010-02-25 15:38:37 -08:00
Russell King
9f33be2c3a Merge branches 'clks' and 'pnx' into devel 2010-02-25 22:10:38 +00:00
Russell King
2741ecb4ce Merge branch 'misc2' into devel 2010-02-25 22:09:41 +00:00
Russell King
2a2d10f386 Merge branch 'for-rmk' of git://git.marvell.com/orion into devel-stable 2010-02-25 20:41:34 +00:00
Ben Dooks
1088f336cc ARM: SAMSUNG: Fix UART number for S5P6442
The recent changes in the UART code mean that we need to ensure that
the 4 UART case is only selected if S5PV210 is being compiled.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-02-24 01:52:20 +00:00
Kukjin Kim
03843a1294 ARM: S5P6442: Add serial port support
This patch adds UART serial port support for S5P6442.

Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-02-24 01:52:19 +00:00
Rabin Vincent
3b43816f68 ARM: 5933/1: amba-pl011: support hardware flow control
Enable/disable automatic hardware flow control as requested by the
termios.  The controller does not allow us to control the RTS line when
auto-RTS is enabled, so we enable auto-RTS only if the kernel has not
disabled RTS.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-02-18 17:29:42 +00:00
Dominik Brodowski
a78621bb11 pcmcia: handle error in serial_cs config calls
Do not ignore the error returned by simple_config() / multi_config().

CC: linux-serial@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2010-02-17 18:00:18 +01:00
Anatolij Gustschin
6acc683351 serial: mpc52xx_uart: re-enable mpc5121 PSC UART support
Currently the support for MPC5121 PSC UART in the mpc52xx_uart
driver is broken (only console pre-initialized by the bootloader
works). Re-enable it now by providing MPC5121 specific ops
for PSCx clock activation, FIFO controller init/uninit and
MPC5121 PSC FIFO shared interrupt handling functions.

Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-02-16 22:30:03 -07:00
Dick Hollenbeck
bca476139d serial: 8250: add serial transmitter fully empty test
When controlling an industrial radio modem it can be necessary to
manipulate the handshake lines in order to control the radio modem's
transmitter, from userspace.

The transmitter should not be turned off before all characters have been
transmitted.  serial8250_tx_empty() was reporting that all characters were
transmitted before they actually were.

===

Discovered in parallel with more testing and analysis by Kees Schoenmakers
as follows:

I ran into an NetMos 9835 serial pci board which behaves a little
different than the standard.  This type of expansion board is very common.

"Standard" 8250 compatible devices clear the 'UART_LST_TEMT" bit together
with the "UART_LSR_THRE" bit when writing data to the device.

The NetMos device does it slightly different

I believe that the TEMT bit is coupled to the shift register.  The problem
is that after writing data to the device and very quickly after that one
does call serial8250_tx_empty, it returns the wrong information.

My patch makes the test more robust (and solves the problem) and it does
not affect the already correct devices.

Alan:

  We may yet need to quirk this but now we know which chips we have a
  way to do that should we find this breaks some other 8250 clone with
  dodgy THRE.

Signed-off-by: Dick Hollenbeck <dick@softplc.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Kees Schoenmakers <k.schoenmakers@sigmae.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-02-16 15:55:51 -08:00
Andy Green
94d32f99c6 imx-serial-excessive-status-clearing-on-break.patch
cc: Sasha Hauer <kernel@pengutronix.de>

We noticed that we were only able to communicate once with a GSM module
per session, if we powered down the module then the serial driver was
broken until reset, no traffic or /proc/interrupts activity could be
seen any more.

Volker noticed it was provoked by a long "break" seen on the wire when
the RX was not driven during powerdown, we discovered we could kill the
serial driver just by forcing RX low extenally for a little while.

I saw that the processing for BREAK in the driver gets too excited and
clears down all set bits in USR2, including that a character is pending.
This stops all further characters getting processed.

The attached one-liner makes the serial driver immortal against BREAK.

Signed-off-by: Andy Green <andy.green@txtr.com>
Signed-off-by: Volker Ernst <volker.ernst@txtr.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2010-02-16 17:16:47 +01:00
Russell King
56012808f4 Merge branch 'for-rmk' of git://git.marvell.com/orion into devel-stable
Conflicts:
	arch/arm/Makefile
2010-02-15 21:20:18 +00:00
Grant Likely
71a157e8ed of: add 'of_' prefix to machine_is_compatible()
machine is compatible is an OF-specific call.  It should have
the of_ prefix to protect the global namespace.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Michal Simek <monstr@monstr.eu>
2010-02-09 08:33:00 -07:00
Magnus Damm
8a77b8d074 serial: sh-sci: Support ARM-based SH-Mobile CPUs.
Add support for ARM-based SH-Mobile CPUs to the sh-sci driver.

Also remove the SCLSR register that is missing on sh772x, sh7705 and
SH-Mobile.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-02-08 12:49:01 +09:00
Magnus Damm
9e9622d1a0 serial: sh-sci: remove SCIF code in sci_rxd_in()
Since sci_rxd_in() is used by SCI only, clean up
the header file by killing off code dealing with
SCIF ports and their register definitions.

Also introduce a default sci_rxd_in() function
which can be shared by all SCIF-only processors.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-02-08 11:47:44 +09:00
Uwe Kleine-König
9ddc5b6f18 tree-wide: fix typos "ammount" -> "amount"
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-02-05 12:22:40 +01:00
Richard Röjfors
03eac7bb88 uartlite: fix crash when using as console
Move the ulite_console_setup to the .devinit section since it might be
called on probe, which is in devinit.  Fixes the crash below where the
uartlite hw is probed after the .init section is freed from the kernel.

uartlite: ttyUL0 at MMIO 0xc8000100 (irq = 30) is a uartlite
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c176720e>] ulite_console_setup+0x6f/0xa8
*pdpt = 0000000036fb0001 *pde = 0000000000000000
Oops: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1f.1/host0/uevent
Modules linked in: puffin(+) serio_raw

Pid: 151, comm: modprobe Not tainted (2.6.31.5-1.0.b1-b1 #1) POULSBO
EIP: 0060:[<c176720e>] EFLAGS: 00010246 CPU: 0
EIP is at ulite_console_setup+0x6f/0xa8
EAX: c16ec824 EBX: c16ec824 ECX: c176719f EDX: 00000000
ESI: 00000000 EDI: c17b42c4 EBP: f6fd1cf0 ESP: f6fd1cd8
 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 151, ti=f6fd0000 task=f6fa1020 task.ti=f6fd0000)
Stack:
 c1031f51 00000000 00000000 00000246 c182237c f7742000 f6fd1d5c c11fd316
<0> c16ec85c f77420d4 0000001e 00000000 00000000 c1633e78 4f494d4d 63783020
<0> 30303038 00303031 f6fd1d3c c10e0786 f6fd1d48 00000000 f6fd1d48 00000000
Call Trace:
 [<c1031f51>] ? register_console+0xf6/0x1fc
 [<c11fd316>] ? uart_add_one_port+0x237/0x2bb
 [<c10e0786>] ? sysfs_add_one+0x13/0xd3
 [<c10e142f>] ? sysfs_do_create_link+0xba/0xfc
 [<c146f200>] ? ulite_probe+0x198/0x1eb
 [<c12064ee>] ? platform_drv_probe+0xc/0xe
 [<c120597b>] ? driver_probe_device+0x79/0x105
 [<c1205a8e>] ? __device_attach+0x28/0x30
 [<c120511f>] ? bus_for_each_drv+0x3d/0x67
 [<c1205af9>] ? device_attach+0x44/0x58
 [<c1205a66>] ? __device_attach+0x0/0x30
 [<c1204fb8>] ? bus_probe_device+0x1f/0x34
 [<c1203e68>] ? device_add+0x385/0x4c0
 [<c148491f>] ? _write_unlock+0x8/0x1f
 [<c1206aac>] ? platform_device_add+0xd9/0x11c
 [<c120c685>] ? mfd_add_devices+0x165/0x1bc
 [<f831b378>] ? puffin_probe+0x2d0/0x390 [puffin]
 [<c11a08ef>] ? pci_match_device+0xa0/0xa7
 [<c11a07bc>] ? local_pci_probe+0xe/0x10
 [<c11a11db>] ? pci_device_probe+0x43/0x66
 [<c120597b>] ? driver_probe_device+0x79/0x105
 [<c1205a4a>] ? __driver_attach+0x43/0x5f
 [<c120535d>] ? bus_for_each_dev+0x3d/0x67
 [<c1205852>] ? driver_attach+0x14/0x16
 [<c1205a07>] ? __driver_attach+0x0/0x5f
 [<c1204dea>] ? bus_add_driver+0xf9/0x220
 [<c1205c8f>] ? driver_register+0x8b/0xeb
 [<c11a1518>] ? __pci_register_driver+0x43/0x9f
 [<c10477ef>] ? __blocking_notifier_call_chain+0x40/0x4c
 [<f831f000>] ? puffin_init+0x0/0x48 [puffin]
 [<f831f017>] ? puffin_init+0x17/0x48 [puffin]
 [<c1001139>] ? do_one_initcall+0x4c/0x131
 [<c105607b>] ? sys_init_module+0xa7/0x1b7
 [<c1002a61>] ? syscall_call+0x7/0xb
 Code: 6e 74 00 00 00 92 33 00 00 18 00 0e 01 73 79 6e 63 65 2d 72 65 67 69 73 74 72 79 0c 00 49 32
00 00 14 00 09 01 61 6c 73 61 2d 69 <6e> 66 6f 00 00 00 42 37 00 00 10 00 07 01 6b 69 6c 6c 61 6c 6c
EIP: [<c176720e>] ulite_console_setup+0x6f/0xa8 SS:ESP 0068:f6fd1cd8
CR2: 0000000000000000

Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-02-02 18:11:22 -08:00
Ben Dooks
1de203adf6 ARM: SAMSUNG: Use PLAT_SAMSUNG instead of PLAT_S3C
As part of the development process, it is hoped PLAT_S3C is either removed
from all of the PLAT_SAMSUNG derived platforms or removed entirely. It is
also better to use PLAT_SAMSUNG as this is the current base of all Samsung
devices.

Change the two places that use PLAT_S3C to use PLAT_SAMSUNG

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-02-03 01:55:02 +00:00
Ben Dooks
3bd9377e87 ARM: SAMSUNG: Add SERIAL_SAMSUNG_UARTS_4 Kconfig option
Add SERIAL_SAMSUNG_UARTS_4 to mop up the number of cases currently using
four Samsung compatible UARTS.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-02-03 01:55:02 +00:00
Michel Pollet
2103040320 ARM: S3C2412: SoC has the fractional baud rate register
The S3C2412 has a fractional baud rate register, this patch adds the
corresponding flag to the UART definition to allow generation of more
precise baud rates for the various clock combinations.

Signed-off-by: Michel Pollet <buserror@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-02-03 01:55:01 +00:00
Thomas Abraham
d85127319c ARM: S5PV210: Add serial port support
This patch adds UART serial port support for S5PV210.

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-01-26 09:50:01 +09:00
Ken Kawasaki
33d7959a7a fmvj18x_cs: add new id (Panasonic lan & modem card)
fmvj18x_cs, serial_cs:
 add new id
 Panasonic lan & modem card (model name:AL-VML101)

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-23 01:08:52 -08:00
Pavel Machek
18c576f950 serial: serial_cs: oxsemi quirk breaks resume
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.

I believe it is simply not a multiport card.  (info->multi == 1).  ...
...  confirmed by printks.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-01-20 15:03:31 -08:00
Roel Kluin
2e2eb509aa serial: imx: bit &/| confusion
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-01-20 15:03:30 -08:00
Alan Cox
16ae2a877b serial: Fix crash if the minimum rate of the device is > 9600 baud
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.

Instead force the rate based on min/max

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-01-20 15:03:29 -08:00
Stanislav Brabec
4547be7809 serial-core: resume serial hardware with no_console_suspend
Perform a tricky suspend/resume even with no_console_suspend.

With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.

Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards

The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them

It allows to capture late console messages without breaking console
after resume.

This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.

"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)

"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)

Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-01-20 15:03:29 -08:00
Matthew Garrett
6d34855d9a serial: 8250_pnp: use wildcard for serial Wacom tablets
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets.  Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-01-20 15:03:27 -08:00
Thomas Abraham
51fe52229e ARM: SAMSUNG: serial: Modify console initialization.
This patch modifies s3c24xx_serial_initconsole function to accept multiple
platform UART information structures. This is required on platforms that have
differences among the instances of UART ports. As an example, the FIFO sizes
could be different for each UART instance and hence multiple platform UART
information structures would be needed.

This patch also modifies the s3c24xx_console_init macro since it wraps the
call to the s3c24xx_serial_initconsole function.

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-01-19 17:50:47 +09:00
Linus Torvalds
8888be69ad Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Move cpu hotplug driver lock from pseries to powerpc
  powerpc: Move /proc/ppc64 to /proc/powerpc update
  powerpc/8xx: Fix user space TLB walk in dcbX fixup
  powerpc: Fix decrementer setup on 1GHz boards
  powerpc/iseries: Initialise on-stack completion
  powerpc/hvc: Driver build breaks with !HVC_CONSOLE
  serial/pmac_zilog: Workaround problem due to interrupt on closed port
  powerpc/macintosh: Make Open Firmware device id constant
  powerpc: Use helpers for rlimits
  powerpc: cpumask_of_node() should handle -1 as a node
  powerpc/pseries: Fix dlpar compile warning without CONFIG_PROC_DEVICETREE
  powerpc/pseries: Fix xics interrupt affinity
  powerpc/swsusp_32: Fix TLB invalidation
  powerpc/8xx: Always pin kernel instruction TLB
  powerpc: 2.6.33 update of defconfigs for embedded 6xx/7xxx, 8xx, 8xxx
  powerpc: Use scripts/mkuboot.sh instead of 'mkimage'
  powerpc/5200: update defconfigs
2010-01-18 14:08:55 -08:00
Ping
3018aa4b1a serial/8250_pnp: add a new Fujitsu Wacom Tablet PC device
This is a new two finger touch Fujitsu Wacom Tablet PC.

Signed-off-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-01-16 12:15:37 -08:00
Kukjin Kim
501dae90b3 ARM: S5P6440: Add serial port support
This patch adds UART serial port support for S5P6440 CPU. Most of the
serial support of Samsung's 6400 CPU is reused for 6440 CPU.

Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2010-01-15 19:16:47 +09:00
Benjamin Herrenschmidt
02ab851324 serial/pmac_zilog: Workaround problem due to interrupt on closed port
It seems that in qemu, we can see an interrupt in R3 despite the
fact that it's masked in W1. The chip doesn't actually issue an
interrupt, but we can "see" it when taking an interrupt for the
other channel. This may be a qemu bug ... or not, so let's be
safe and avoid calling into the UART layer when that happens which
woulc cause a crash.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Rob Landley <rob@landley.net>
2010-01-15 13:26:13 +11:00
Markus Pietrek
75136d48e8 serial: sh-sci: using correct fifo size for SCIF and SCIFA ports.
The sh-sci driver used the wrong fifosize for PORT_SCIFA and PORT_SCIF
ports. If an incorrect size is used, the serial core will enforce an
early shutdown on the port, especially with baudrates < 9600.

Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-01-15 08:33:20 +09:00
Linus Torvalds
1f0e14bbc0 Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
  ARM: Fix wrong dmb
  ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
  ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
  ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
  ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
  ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
  ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
  ARM: 5867/1: Update U300 defconfig
  ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
  [ARM] pxa: fix strange characters in zaurus gpio .desc
  ARM: add missing recvmmsg syscall number
  [ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
  [ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
  [ARM] pxa: enable L2 if present in XSC3
  [ARM] pxa: do not enable L2 after MMU is enabled
2010-01-12 20:56:01 -08:00
Linus Torvalds
597d8c7178 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
  sky2: Fix oops in sky2_xmit_frame() after TX timeout
  Documentation/3c509: document ethtool support
  af_packet: Don't use skb after dev_queue_xmit()
  vxge: use pci_dma_mapping_error to test return value
  netfilter: ebtables: enforce CAP_NET_ADMIN
  e1000e: fix and commonize code for setting the receive address registers
  e1000e: e1000e_enable_tx_pkt_filtering() returns wrong value
  e1000e: perform 10/100 adaptive IFS only on parts that support it
  e1000e: don't accumulate PHY statistics on PHY read failure
  e1000e: call pci_save_state() after pci_restore_state()
  netxen: update version to 4.0.72
  netxen: fix set mac addr
  netxen: fix smatch warning
  netxen: fix tx ring memory leak
  tcp: update the netstamp_needed counter when cloning sockets
  TI DaVinci EMAC: Handle emac module clock correctly.
  dmfe/tulip: Let dmfe handle DM910x except for SPARC on-board chips
  ixgbe: Fix compiler warning about variable being used uninitialized
  netfilter: nf_ct_ftp: fix out of bounds read in update_nl_seq()
  mv643xx_eth: don't include cache padding in rx desc buffer size
  ...

Fix trivial conflict in drivers/scsi/cxgb3i/cxgb3i_offload.c
2010-01-12 20:53:29 -08:00
Simon Kagstrom
cc20b900be ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
The console hangs during bootup when disable_irq is called from the
transmit interrupt handler (it will wait forever for it's "own"
interrupt in synchronize_irq). Fix by using disable_irq_nosync()
instead.

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-01-11 15:39:21 +00:00
Ken Kawasaki
abe8806901 pcnet_cs: add cis of KTI PE520 pcmcia network card
pcnet_cs,serial_cs:

add cis of KTI PE520 pcmcia network card,
and serial card(Sierra Wireless AC860).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-01-06 20:37:58 -08:00
Paul Mundt
32b53076c3 serial: sh-sci: Convert tremaining ctrl_xxx I/O routines to __raw_xxx.
ctrl_xxx() is an antiquated SH interface, while __raw_xxx is the standard
API that accomplishes the same thing. As such, this converts the
remaining sh-sci straggles over, which enables the driver to be wired up
for ARM SH-Mobile CPUs as well.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-12-24 14:52:43 +09:00
Magnus Damm
154280fd0e serial: sh-sci: earlyprintk zero uartclk fix
This establishes a sensible max baud rate for the earlyprintk cases where
the port's uartclk has not yet been determined.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-12-24 14:50:55 +09:00
Linus Torvalds
9b2831704e Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (33 commits)
  sh: Fix test of unsigned in se7722_irq_demux()
  sh: mach-ecovec24: Add FSI sound support
  sh: mach-ecovec24: Add mt9t112 camera support
  sh: mach-ecovec24: Add tw9910 support
  sh: MSIOF/mmc_spi platform data for the Ecovec24 board
  sh: ms7724se: Add ak4642 support
  sh: Fix up FPU build for SH5
  sh: Remove old early serial console code V2
  sh: sh5 scif pdata (sh5-101/sh5-103)
  sh: sh4a scif pdata (sh7757/sh7763/sh7770/sh7780/sh7785/sh7786/x3)
  sh: sh4a scif pdata (sh7343/sh7366/sh7722/sh7723/sh7724)
  sh: sh4 scif pdata (sh7750/sh7760/sh4-202)
  sh: sh3 scif pdata (sh7705/sh770x/sh7710/sh7720)
  sh: sh2a scif pdata (sh7201/sh7203/sh7206/mxg)
  sh: sh2 scif pdata (sh7616)
  sh-sci: Extend sh-sci driver with early console V2
  sh: Stub in P3 ioremap support for nommu parts.
  sh: wire up vmallocinfo support in ioremap() implementations.
  sh: Make the unaligned trap handler always obey notification levels.
  sh: Couple kernel and user write page perm bits for CONFIG_X2TLB
  ...
2009-12-16 10:29:52 -08:00
Jean Delvare
9385565e20 ioc3/ioc4: fix error path on driver registration
Two IOC3 and IOC4 drivers have broken error paths on registration.  Fix
them.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:27 -08:00
Jean Delvare
2ea5d35a49 ioc3/ioc4: various section fixes
Several IOC3 and IOC4 drivers misuse the __devinit and __devexit section
markers.  Use __init and __exit instead as appropriate, then add __devinit
and __devexit where they really belong for PCI drivers.

Also make ioc4_serial_init static.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Pat Gefre <pfg@sgi.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:27 -08:00
Alexey Dobriyan
471452104b const: constify remaining dev_pm_ops
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-12-15 08:53:25 -08:00
Paul Mundt
e0aa51f54f Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 2009-12-15 12:10:10 +09:00
Magnus Damm
7b6fd3bf82 sh-sci: Extend sh-sci driver with early console V2
This is V2 of early serial console support for the sh-sci
driver. The early serial console is using early platform
devices and "earlyprintk". To use this feature the early
platform devices must be broken out to one device per port
and the desired port should be selected on the kernel command
line like: "earlyprintk=sh-sci.N[,baudrate][,keep]"

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-12-15 12:06:29 +09:00
Linus Torvalds
0f4974c439 Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (58 commits)
  tty: split the lock up a bit further
  tty: Move the leader test in disassociate
  tty: Push the bkl down a bit in the hangup code
  tty: Push the lock down further into the ldisc code
  tty: push the BKL down into the handlers a bit
  tty: moxa: split open lock
  tty: moxa: Kill the use of lock_kernel
  tty: moxa: Fix modem op locking
  tty: moxa: Kill off the throttle method
  tty: moxa: Locking clean up
  tty: moxa: rework the locking a bit
  tty: moxa: Use more tty_port ops
  tty: isicom: fix deadlock on shutdown
  tty: mxser: Use the new locking rules to fix setserial properly
  tty: mxser: use the tty_port_open method
  tty: isicom: sort out the board init logic
  tty: isicom: switch to the new tty_port_open helper
  tty: tty_port: Add a kref object to the tty port
  tty: istallion: tty port open/close methods
  tty: stallion: Convert to the tty_port_open/close methods
  ...
2009-12-11 15:34:40 -08:00
Ian Jackson
68cb4f8e24 Serial: Do not read IIR in serial8250_start_tx when UART_BUG_TXEN
Do not read IIR in serial8250_start_tx when UART_BUG_TXEN

Reading the IIR clears some oustanding interrupts so it is not safe.
Instead, simply transmit immediately if the buffer is empty without
regard to IIR.

Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jiri Kosina <jkosina@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:05 -08:00
Uwe Kleine-König
c934878cc0 Serial: pxa: work around Errata #75
Intel(R) PXA27x Processor Family Specification Update (Nov 2005)
says:

  E75. UART: Baud rate may not be programmed correctly on
       back-to-back writes.

  Problem:
  When programming the Divisor Latch registers, Low and High (DLL and
  DLH), with back-to-back writes, the second register write may not
  take effect. The result is an incorrect baud rate.

  Workaround:
  After programming the first Divisor Latch register, read and verify
  it before programming the second Divisor Latch register.

This was hit when changing the baud rate from 115200 to 9600 while
receiving characters at 9600 Bd.

And fixed indention of some comments nearby.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:04 -08:00
André Goddard Rosa
4c0ebb8057 serial, 8250: calculate irqflags bitmask before loop
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:04 -08:00
André Goddard Rosa
82cb7ba10d serial: cascade needless conditionals
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:04 -08:00
André Goddard Rosa
9e845abfc8 serial: fix NULL pointer dereference
If kzalloc() or alloc_tty_driver() fails, we call:
    put_tty_driver(normal = NULL).

Then:
    put_tty_driver -> tty_driver_kref_put -> kref_put(&NULL->kref, ...)

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:04 -08:00
Breno Leitao
e6bdf24cf2 jsm: adding EEH handlers
Adding EEH handlers for the serial jsm driver. This patch adds
the PCI error handlers and also register them to be called when
a error is detected.

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:03 -08:00
Breno Leitão
f9d1dff276 jsm: removing the field jsm_board->intr_count
Currently there is a field in the jsm_board structure to cont
the number of interrupt that the card recevived, but it's not
working properly when the IRQ line is shared, and also nowhere
else this field is used. So, This patch is removing it.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:03 -08:00
Breno Leitão
a44829dd8b jsm: Removing unused jsm_channel->ch_wopen field
Currently the jsm_channel->ch_wopen field is defined and never
used. So, this patch removes it.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:03 -08:00
Breno Leitão
2fd107c015 jsm: Remove ch_cpstime field
Currently the field jsm_channel->ch_cpstime is defined but never
used, so this patch removes it.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:03 -08:00
Breno Leitão
cead486f40 jsm: removing ch_old_baud field
Currently the field jsm_channel->ch_old_baud is not used, just
assigned in a lot of places but never used. This patches removes
this field.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:02 -08:00
Breno Leitão
a53568a22a jsm: remove the ch_custom_speed field
Currently the ch_custom_speed field exists but is never used,
so, this patch removes it.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:02 -08:00
Breno Leitão
354aaf964e jsm: Rewriting a bad log message
Actually jsm displays "Device Added" 8 times (for a 8 port device).
This silly patch just makes things more informative, showing
the port (instead of the device) that was added.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:02 -08:00
Breno Leitão
a88a477f1d jsm: IRQ handlers doesn't need to have IRQ_DISABLED enabled
Currently jsm is showing the following message when loaded:

IRQ 432/JSM: IRQF_DISABLED is not guaranteed on shared IRQs

It's because the request_irq() is called using IRQF_DISABLED
and IRQF_SHARED.
Actually there is no need to use IRQF_DISABLED in this driver.

Signed-off-by: Breno Leitão <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <scottk@digi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 15:18:02 -08:00
Johannes Berg
9ebfbd45f9 firmware_class: make request_firmware_nowait more useful
Unfortunately, one cannot hold on to the struct firmware
that request_firmware_nowait() hands off, which is needed
in some cases. Allow this by requiring the callback to
free it (via release_firmware).

Additionally, give it a gfp_t parameter -- all the current
users call it from a GFP_KERNEL context so the GFP_ATOMIC
isn't necessary. This also marks an API break which is
useful in a sense, although that is obviously not the
primary purpose of this change.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 11:24:52 -08:00
Linus Torvalds
4ef58d4e2a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
  tree-wide: fix misspelling of "definition" in comments
  reiserfs: fix misspelling of "journaled"
  doc: Fix a typo in slub.txt.
  inotify: remove superfluous return code check
  hdlc: spelling fix in find_pvc() comment
  doc: fix regulator docs cut-and-pasteism
  mtd: Fix comment in Kconfig
  doc: Fix IRQ chip docs
  tree-wide: fix assorted typos all over the place
  drivers/ata/libata-sff.c: comment spelling fixes
  fix typos/grammos in Documentation/edac.txt
  sysctl: add missing comments
  fs/debugfs/inode.c: fix comment typos
  sgivwfb: Make use of ARRAY_SIZE.
  sky2: fix sky2_link_down copy/paste comment error
  tree-wide: fix typos "couter" -> "counter"
  tree-wide: fix typos "offest" -> "offset"
  fix kerneldoc for set_irq_msi()
  spidev: fix double "of of" in comment
  comment typo fix: sybsystem -> subsystem
  ...
2009-12-09 19:43:33 -08:00
Linus Torvalds
701791cc3c Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: export clk_* symbols in clk.c
  m68knommu: Split the .init section into INIT_TEXT_SECTION and INIT_DATA_SECTION.
  m68knommu: Move __init_end out of the .init section.
  m68knommu: Move __init_begin out of the .init section.
  m68knommu: Use more macros inside the .init section.
  m68knommu: Use INIT_TASK_DATA and CACHELINE_ALIGNED_DATA.
  m68knommu: Make THREAD_SIZE available to assembly files.
  m68knommu: Don't hardcode the value of PAGE_SIZE in the linker script.
  m68knommu: rename BSS define in linker script
  m68knommu: add a task_pt_regs() macro
  m68knommu: define arch_has_single_step() and friends
  m68knommu: add uboot commandline argument passing support
  m68knommu: Coldfire GPIO corrections
  m68knommu: move mcf_remove to .devexit.text

Fixed up (?) conflict in arch/m68k/include/asm/ptrace.h
2009-12-09 19:09:42 -08:00
Linus Torvalds
3a43aaa317 Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
  sh: include empty zero page in romImage
  sh: Make associative cache writes fatal on all SH-4A parts.
  sh: Drop associative writes for SH-4 cache flushes.
  sh: Partial revert of copy/clear_user_highpage() optimizations.
  sh: Add default uImage rule for se7724, ap325rxa, and migor.
  sh: allow runtime pm without suspend/resume callbacks
  sh: mach-ecovec24: Remove un-defined settings for VPU
  sh: mach-ecovec24: LCDC drive ability become high
  sh: fix sh7724 VEU3F resource size
  serial: sh-sci: Fix too early port disabling.
  sh: pfc: pr_info() -> pr_debug() cleanups.
  sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
  sh: Improve kfr2r09 serial port setup code
  sh: Break out SuperH PFC code
  sh: Move KEYSC header file
  sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
  sh: Add CPG save/restore code for sh7724 R-standby
  sh: Add SDHI power control support to Ecovec
  mfd: Add power control platform data to SDHI driver
  sh: mach-ecovec24: modify address map
  ...
2009-12-09 19:03:16 -08:00
Linus Torvalds
79c9601c2e Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (272 commits)
  Fix soc_common PCMCIA configuration
  ARM: 5827/1: SA1100: h3100/h3600: emit messages on failed gpio_request
  ARM: 5826/1: SA1100: h3100/h3600: always build htc-egpio driver
  ARM: 5825/1: SA1100: h3600: update defconfig
  ARM: 5824/1: SA1100: reuse h3600 PCMCIA driver on h3100
  ARM: 5823/1: SA1100: h3100/h3600: add support for gpio-keys
  ARM: 5822/1: SA1100: h3100/h3600: clean up #includes
  ARM: 5821/1: SA1100: h3100/h3600: revise copyright boilerplates
  ARM: 5820/1: SA1100: h3100/h3600: split h3600.c
  ARM: 5819/1: SA1100: h3100/h3600: merge h3600.h and h3600_gpio.h into h3xxx.h
  ARM: 5818/1: SA1100: h3100/h3600: drop old GPIO definitions
  ARM: 5817/1: SA1100: h3100/h3600: configure all unused gpios as inputs
  ARM: 5816/1: SA1100: h3600: remove IRQ_GPIO_* definitions
  ARM: 5815/1: SA1100: h3100/h3600: remove now unused assign_h3600_egpio handlers
  ARM: 5814/1: SA1100: h3100/h3600: convert all users of assign_h3600_egpio to gpiolib
  ARM: 5813/1: SA1100: h3100/h3600: add htc-egpio driver
  ARM: 5812/1: SA1100: h3100/h3600: separate machine-specific LCD helpers
  ARM: 5811/2: pcmcia: convert sa1100_h3600 driver to gpiolib
  ARM: 5799/1: SA1100: h3600: stop setting direction for LCD pins
  ARM: 5798/1: SA1100: h3600: remove unused cruft from h3600.h
  ...
2009-12-08 08:12:43 -08:00
Linus Torvalds
ee1262dbc6 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
  sparc: Set UTS_MACHINE correctly.
  sparc,leon: init_leon srmmu cleanup
  sparc32: Remove early interrupt enable.
  sparc, leon: Added Aeroflex Gaisler entry in manufacturer_info structure
  sparc64: Faster early-boot framebuffer console.
  Revert "sparc: Make atomic locks raw"
  sparc: remove unused nfsd #includes
  sparc: Fixup last users of irq_chip->typename
  Added sparc_leon3_snooping_enabled() and converted extern inline to static inline
  No auxio on LEON
  apbuart: Use of_find_node_by_path to find root node.
  sparc: Replace old style lock initializer
  sparc: Make atomic locks raw
  apbuart: Fix build and missing driver unregister.
  apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
  apbuart: Fix build warning.
  sparc: Support for GRLIB APBUART serial port
  watchdog: Remove BKL from rio watchdog driver
  sparc: Remove BKL from apc
  sparc,leon: Sparc-Leon SMP support
2009-12-08 07:48:23 -08:00
Jiri Kosina
d014d04386 Merge branch 'for-next' into for-linus
Conflicts:

	kernel/irq/chip.c
2009-12-07 18:36:35 +01:00
Russell King
3d14b5beba Merge branch 'sa1100' into devel 2009-12-06 17:00:33 +00:00
Linus Torvalds
d9b2c4d0b0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
  pcmcia: rework the irq_req_t typedef
  pcmcia: remove deprecated handle_to_dev() macro
  pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
  pcmcia: remove unused "window_t" typedef
  pcmcia: move some window-related code to pcmcia_ioctl.c
  pcmcia: Change window_handle_t logic to unsigned long
  pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
  pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
  pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
  drivers/pcmcia: remove unnecessary kzalloc
  pcmcia: correct handling for Zoomed Video registers in topic.h
  pcmcia: fix printk formats
  pcmcia: autoload module pcmcia
  pcmcia/staging: update comedi drivers
  PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
  PCMCIA: ss: allow PCI IRQs > 255
  PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
  PCMCIA: soc_common: constify soc_pcmcia_socket ops member
  PCMCIA: sa1111: remove duplicated initializers
  PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
  ...
2009-12-05 09:42:59 -08:00
Russell King
0719dc3413 Merge branch 'devel-stable' into devel 2009-12-05 10:35:33 +00:00
André Goddard Rosa
af901ca181 tree-wide: fix assorted typos all over the place
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:55 +01:00
Guennadi Liakhovetski
b1516803d5 serial: sh-sci: Fix too early port disabling.
Currently serial ports on SH CPUs get disabled too early, because the
sci_tx_empty() routine claims to not be able to detect whether the
transmission has been completed and just always returns TIOCSER_TEMT. This
results in corrupt output of last characters if the port is not open for
reading at the same time. It is however possible to detect whether
transmission has been completed. Use the TEND bit of the status register
for this.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-12-04 13:42:23 +09:00
Uwe Kleine-König
d6f80e3a2a m68knommu: move mcf_remove to .devexit.text
The function mcf_remove is used only wrapped by __devexit_p so define it
using __devexit.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
2009-12-04 11:45:30 +10:00
Ben Dooks
ccae941ee2 ARM: S3C: Update Simtec copyright statements from , to - [2]
There are a number of statements of the form A, B or A, B, C where
the numbers A,B,C are not consecutive. However, referencing [1] it
is the correct thing to replace these with A-B or A-C as apropriate.

[1] http://www.copyrightservice.co.uk/copyright/p03_copyright_notices
    section 4iii 'Year of publication'

Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
2009-12-01 01:33:51 +00:00
Michal Simek
16173c7c2d tty/of_serial: add missing ns16550a id
Many boards have a bug-free ns16550 compatible serial port, which we should
register as PORT_16550A. This introduces a new value "ns16550a" for the
compatible property of of_serial to let a firmware choose that model instead
of using the crippled PORT_16550 mode.

Reported-by: Alon Ziv <alonz@nolaviz.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-30 16:38:44 -08:00
Maxime Bizon
b037179f7a bcm63xx_uart: Fix serial driver compile breakage.
The driver missed a small API change while sitting in Ralf's tree, this
patch makes it compile again.

Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-30 16:38:32 -08:00
Linus Torvalds
ffece4808d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sunsu: Use sunserial_console_termios() in sunsu_console_setup().
  sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
  serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
  serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
  sunsu: Fix detection of SU ports which are RSC console or control.
  sunsab: Do not set sunsab_reg.cons right before registering minors.
  sparc64: Fix definition of VMEMMAP_SIZE.
2009-11-30 14:02:23 -08:00
Dominik Brodowski
5fa9167a1b pcmcia: rework the irq_req_t typedef
Most of the irq_req_t typedef'd struct can be re-worked quite
easily:

(1) IRQInfo2 was unused in any case, so drop it.

(2) IRQInfo1 was used write-only, so drop it.

(3) Instance (private data to be passed to the IRQ handler):
	Most PCMCIA drivers using pcmcia_request_irq() to actually
	register an IRQ handler set the "dev_id" to the same pointer
	as the "priv" pointer in struct pcmcia_device. Modify the two
	exceptions (ipwireless, ibmtr_cs) to also work this waym and
	set the IRQ handler's "dev_id" to p_dev->priv unconditionally.

(4) Handler is to be of type irq_handler_t.

(5) Handler != NULL already tells whether an IRQ handler is present.
	Therefore, we do not need the IRQ_HANDLER_PRESENT flag in
	irq_req_t.Attributes.

CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-scsi@vger.kernel.org
CC: alsa-devel@alsa-project.org
CC: Jaroslav Kysela <perex@perex.cz>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Karsten Keil <isdn@linux-pingi.de>
for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2009-11-28 18:03:14 +01:00
Dominik Brodowski
dd2e5a1565 pcmcia: remove deprecated handle_to_dev() macro
Update remaining users and remove deprecated handle_to_dev() macro

CC: Harald Welte <laforge@gnumonks.org>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2009-11-28 18:03:10 +01:00
Paul Mundt
edad1f208e serial: sh-sci: Depend on HAVE_CLK unconditionally.
The sh-sci code conditionalized the clock framework support in order to
give the other platforms a chance to catch up. sh64 supported this some
time ago and the forthcoming ARM changes handle this as well, this leaves
h8300 as the odd one out. H8300 has had since 2.5 to merge it's sh-sci
support upstream, and has yet to do so. At this point I will no longer be
holding back the driver to support an unreponsive architecture, 7 years
is quite enough of a grace period. Support is easily implemented on the
architecture if and when it ever decides to merge its changes upstream.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-11-25 16:23:35 +09:00
Uwe Kleine-König
b9e39c89a9 serial: sh-sci: don't use __devexit_p to wrap sci_remove
The function sci_remove is defined without any section modifier, so
don't use __devexit_p to wrap it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-11-25 10:39:43 +09:00
David S. Miller
be24656a5e sunsu: Use sunserial_console_termios() in sunsu_console_setup().
Be like the other Sun serial drivers otherwise the special handling of
OpenFirmware options and hard-coded overrides for LOM/RSC consoles
will not be handled.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-24 14:12:50 -08:00
David S. Miller
1917d17b90 sunsu: Pass true 'ignore_line' to console match when RSC or LOM console.
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-24 14:11:40 -08:00
David S. Miller
457931de3b serial: suncore: Fix RSC/LOM handling in sunserial_console_termios().
RSC and LOM devices have fixed speed settings.

We already had some code to match and handle "rsc" named devices on
E250 systems, but we also have to handle 'rsc-console', 'rsc-control',
and 'lom-console'.

Also, in order to get this right regardless of what 'output-device'
happens to be, explicitly pass the UART device node pointer to this
routine.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-24 14:09:56 -08:00
David S. Miller
4e3533d05b serial: suncore: Add 'ignore_line' argument to sunserial_console_match().
This tells the logic to ignore the line match when deciding whether the
device is the OpenFirmware specified console device or not.

This is going to be used in the SU driver for rsc-console detection.

There is probably a better way to handle this, but this is the least
intrusive solution for now which we can validate won't break any other
cases.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-24 14:03:34 -08:00
David S. Miller
8301d386af sunsu: Fix detection of SU ports which are RSC console or control.
These device nodes are named "rsc-console" and "rsc-control" rather
than 'serial', but the device_type property is 'serial' so we'll
tip off of that for detection.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-24 13:58:52 -08:00
David S. Miller
4e68e18841 sunsab: Do not set sunsab_reg.cons right before registering minors.
Other Sun serial drivers do not do this, and if we keep it this way
it ends up registering all serial devices as consoles rather than
just the one which we explicitly register via sunserial_console_match()
which uses add_preferred_console().

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-24 13:56:39 -08:00
Kristoffer Glembo
4edd5ad0f5 apbuart: Use of_find_node_by_path to find root node.
Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-13 13:25:06 -08:00
Lennert Buytenhek
b87e5e2b8e serial: add support for the Lava Quattro PCI quad-port 16550A card
This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-11-12 07:25:57 -08:00
Lennert Buytenhek
80647b959f serial: fix printk format specifiers for struct uart_port::iobase
struct uart_port::iobase is unsigned long, so use %lx as printk format
specifier.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-11-12 07:25:57 -08:00
Dominik Brodowski
9ec0bf41b5 pcmcia: use dynamic debug infrastructure, deprecate CS_CHECK (serial_cs)
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of
requiring manual settings of PCMCIA_DEBUG.

Also, remove all usages of the CS_CHECK macro and replace them with proper
Linux style calling and return value checking. The extra error reporting may
be dropped, as the PCMCIA core already complains about any (non-driver-author)
errors.

CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2009-11-09 08:30:04 +01:00
David S. Miller
ddaf1b27ed apbuart: Fix build and missing driver unregister.
linux/of_platform.h needs to be included

OF driver needs to be unregistered

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-06 00:26:39 -08:00
Magnus Damm
345e5a7672 serial: sh-sci: disable callback typo fix
Avoid invoking the disable callback in case of NULL.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-11-06 17:23:04 +09:00
David S. Miller
d13500981e apbuart: Kill dependency on deprecated Sparc-only PROM interfaces.
Use the proper modern OF ones instead.

Noticed by Stephen Rothwell.

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-04 23:59:18 -08:00
David S. Miller
384a17b284 apbuart: Fix build warning.
drivers/serial/apbuart.c: In function ‘apbuart_probe’:
drivers/serial/apbuart.c:574: warning: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘resource_size_t’

Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-04 08:47:03 -08:00
Kristoffer Glembo
d4ac42a582 sparc: Support for GRLIB APBUART serial port
This patch adds support for the APBUART serial port from Aeroflex
Gaisler's IP library GRLIB. It is currently used in all LEON3 designs
(SPARC V8) but can be used on other platforms as well (which support OF).

Signed-off-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-04 08:44:54 -08:00
Linus Torvalds
a84216e671 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
  mac80211: check interface is down before type change
  cfg80211: fix NULL ptr deref
  libertas if_usb: Fix crash on 64-bit machines
  mac80211: fix reason code output endianness
  mac80211: fix addba timer
  ath9k: fix misplaced semicolon on rate control
  b43: Fix DMA TX bounce buffer copying
  mac80211: fix BSS leak
  rt73usb.c : more ids
  ipw2200: fix oops on missing firmware
  gre: Fix dev_addr clobbering for gretap
  sky2: set carrier off in probe
  net: fix sk_forward_alloc corruption
  pcnet_cs: add cis of PreMax PE-200 ethernet pcmcia card
  r8169: Fix card drop incoming VLAN tagged MTU byte large jumbo frames
  ibmtr: possible Read buffer overflow?
  net: Fix RPF to work with policy routing
  net: fix kmemcheck annotations
  e1000e: rework disable K1 at 1000Mbps for 82577/82578
  e1000e: config PHY via software after resets
  ...
2009-11-03 07:44:01 -08:00
Ken Kawasaki
63ca2d74ea pcnet_cs: add cis of PreMax PE-200 ethernet pcmcia card
pcnet_cs,serial_cs:

add cis of PreMax ethernet pcmcia card,
and some Sierra Wireless serial card(AC555, AC7xx, AC8xx).

use PROD_ID for AC7xx, because MANF_ID of AC7xx and AC8xx are the same.

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-29 22:51:25 -07:00
Linus Torvalds
0a53f1693c Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/ppc64: Use preempt_schedule_irq instead of preempt_schedule
  powerpc: Minor cleanup to lib/Kconfig.debug
  powerpc: Minor cleanup to sound/ppc/Kconfig
  powerpc: Minor cleanup to init/Kconfig
  powerpc: Limit memory hotplug support to PPC64 Book-3S machines
  powerpc: Limit hugetlbfs support to PPC64 Book-3S machines
  powerpc: Fix compile errors found by new ppc64e_defconfig
  powerpc: Add a Book-3E 64-bit defconfig
  powerpc/booke: Fix xmon single step on PowerPC Book-E
  powerpc: Align vDSO base address
  powerpc: Fix segment mapping in vdso32
  powerpc/iseries: Remove compiler version dependent hack
  powerpc/perf_events: Fix priority of MSR HV vs PR bits
  powerpc/5200: Update defconfigs
  drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEM
  powerpc/boot/dts: drop obsolete 'fsl5200-clocking'
  of: Remove nested function
  mpc5200: support for the MAN mpc5200 based board mucmc52
  mpc5200: support for the MAN mpc5200 based board uc101
2009-10-29 08:59:06 -07:00
Benjamin Herrenschmidt
c68d2b1594 8250_pci: add IBM Saturn serial card
The IBM Saturn serial card has only one port. Without that fixup,
the kernel thinks it has two, which confuses userland setup and
admin tools as well.

[akpm@linux-foundation.org: fix pci-ids.h layout]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Michael Reed <mreed10@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-29 07:39:30 -07:00
Krauth.Julien
1b62cbf214 serial: add ADDI-DATA GmbH PCI-Express communication cards in 8250_pci.c and pci_ids.h
Add support for ADDI-DATA GmbH PCI-Express communication cards:

APCIe-7300
APCIe-7420
APCIe-7500
APCIe-7800

Warning: 8250_pci.c depends on pci_ids.h. 8250_pci.c

Signed-off-by: Krauth Julien <Krauth.Julien@addi-data.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-29 07:39:30 -07:00
Haavard Skinnemoen
9d09daf8e8 atmel_serial: fix bad BUILD_BUG_ON() usage
is_power_of_2() appears not to be constant enough for BUILD_BUG_ON()
after the latest rework, so replace it with an open-coded test.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-29 07:39:30 -07:00
Benjamin Herrenschmidt
40578fca24 Merge commit 'gcl/merge' into merge 2009-10-28 09:56:18 +11:00
Dominik Brodowski
6ae3b84d97 serial_cs: use pcmcia_loop_config() and pre-determined values
As the PCMCIA core already determines the multifunction count, the
ConfigBase address and the Present value, we can use them directly
instead of parsing the CIS again. By making use of pcmcia_loop_config(),
we can further remove the remaining call to pcmcia_get_first_tuple()
and friends.

CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
2009-10-24 17:13:01 +02:00
Julia Lawall
b7a8212cae drivers/serial/mpc52xx_uart.c: Use UPIO_MEM rather than SERIAL_IO_MEM
As in the commit 9b4a161777, use UPIO_MEM
rather than SERIAL_IO_MEM.  Both have the same value.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@has_sc@
@@

#include <linux/serial_core.h>

@depends on has_sc@
@@

- SERIAL_IO_MEM
+ UPIO_MEM
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2009-10-15 09:58:28 -06:00
Linus Torvalds
eea7e17e0e tty, serial: Fix race and NULL check in uart_close()
Commit 46d57a449a ("serial: use tty_port pointers in the core code")
contained two bugs that causes (rare) crashes:

 - the rename typoed one site

 - a NULL check was missed

Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-12 10:21:33 -07:00
Linus Torvalds
5587481e92 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
  ethoc: limit the number of buffers to 128
  ethoc: use system memory as buffer
  ethoc: align received packet to make IP header at word boundary
  ethoc: fix buffer address mapping
  ethoc: fix typo to compute number of tx descriptors
  au1000_eth: Duplicate test of RX_OVERLEN bit in update_rx_stats()
  netxen: Fix Unlikely(x) > y
  pasemi_mac: ethtool get settings fix
  add maintainer for network drop monitor kernel service
  tg3: Fix phylib locking strategy
  rndis_host: support ETHTOOL_GPERMADDR
  ipv4: arp_notify address list bug
  gigaset: add kerneldoc comments
  gigaset: correct debugging output selection
  gigaset: improve error recovery
  gigaset: fix device ERROR response handling
  gigaset: announce if built with debugging
  gigaset: handle isoc frame errors more gracefully
  gigaset: linearize skb
  gigaset: fix reject/hangup handling
  ...
2009-10-08 11:59:30 -07:00
Ken Kawasaki
bf6fda63c4 pcnet_cs: add cis of National Semicondoctor's multifunction pcmcia card
pcnet_cs,serial_cs:
  
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).

Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-10-05 00:40:03 -07:00
Linus Torvalds
a037a79dce Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (25 commits)
  ARM: 5728/1: Proper prefetch abort handling on ARMv6 and ARMv7
  ARM: 5727/1: Pass IFSR register to do_PrefetchAbort()
  ARM: 5740/1: fix valid_phys_addr_range() range check
  ARM: 5739/1: ARM: allow empty ATAG_CORE
  ARM: 5735/1: sa1111: CodingStyle cleanups
  ARM: 5738/1: Correct TCM documentation
  ARM: 5734/1: arm: fix compilation of entry-common.S for older CPUs
  ARM: 5733/1: fix bcmring compile error
  ARM: 5732/1: remove redundant include file
  ARM: 5731/2: Fix U300 generic GPIO, remove ifdefs from MMCI v3
  ARM: Ensure do_cache_op takes mmap_sem
  ARM: Fix __cpuexit section mismatch warnings
  ARM: Don't allow highmem on SMP platforms without h/w TLB ops broadcast
  ARM: includecheck fix: mach-davinci, board-dm365-evm.c
  ARM: Remove unused CONFIG SA1100_H3XXX
  ARM: Fix warning: unused variable 'highmem'
  ARM: Fix warning: #warning syscall migrate_pages not implemented
  ARM: Fix SA11x0 clocksource warning
  ARM: Fix SA1100 Neponset serial section mismatch
  ARM: Fix SA1100 Assabet/Neponset PCMCIA section mismatch warnings
  ...
2009-10-02 16:20:43 -07:00
Chuck Ebbert
d41a4b515e serial: add parameter to force skipping the test for the TXEN bug
Allow users to force skipping the TXEN test at init time. Applies
to all serial ports. Intended for debugging only.

There is a blacklist for devices where we need to skip the test but the
list is not complete.  This lets users force skipping the test so we can
determine if they need to be added to the list.

Some HP machines with weird serial consoles have this problem and there
may be more.

Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:16 -07:00
Breno Leitao
75e3a6aed9 icom: convert space to tabs
Convert spaces to tabs and remove wrong spaces

Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: Scott Kilau <Scott.Kilau@digi.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Atsushi Nemoto
aa76224a38 serial_txx9: use container_of() instead of direct cast
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:15 -07:00
Richard Röjfors
447e4460a4 uartlite: allow building for timberdale MFD
Some configurations of the Timberdale FPGA has the uartlite
included.

Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-10-01 16:11:12 -07:00
Maxime Bizon
9fcd66e572 MIPS: BCM63xx: Add serial driver for bcm63xx integrated UART.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2009-09-30 21:46:59 +02:00
Russell King
3f944ab115 ARM: Fix SA1100 Neponset serial section mismatch
WARNING: vmlinux.o(.devinit.text+0x524): Section mismatch in reference from the function neponset_probe() to the function .init.text:sa1100_register_uart_fns()
The function __devinit neponset_probe() references
a function __init sa1100_register_uart_fns().
If sa1100_register_uart_fns is only used by neponset_probe then
annotate sa1100_register_uart_fns with a matching annotation.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
2009-09-28 18:06:16 +01:00
Linus Torvalds
8e44e43477 Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  Fix build of cpm_uart due to core changes
  powerpc/8xx: Fix regression introduced by cache coherency rewrite
  powerpc/4xx: Fix erroneous xmon warning on PowerPC 4xx
  powerpc/mm: Fix 40x and 8xx vs. _PAGE_SPECIAL
  powerpc: Cleanup linker script using new linker script macros.
  powerpc: Fix ibm,client-architecture-support printout
  powerpc: Increase NODES_SHIFT on 64bit from 4 to 8
  powerpc/perf_counter: Fix vdso detection
  powerpc: Move 64bit heap above 1TB on machines with 1TB segments
  powerpc: Change archdata dma_data to a union
  powerpc: Rename get_dma_direct_offset get_dma_offset
  powerpc/mm: Remove duplicated #include
  powerpc/book3e-64: Remove duplicated #include
  powerpc: Check for unsupported relocs when using CONFIG_RELOCATABLE
  powerpc/pmc: Don't access lppaca on Book3E
  powerpc: kmalloc failure ignored in vio_build_iommu_table()
  hvc_console: Provide (un)locked version for hvc_resize()
2009-09-24 17:22:31 -07:00
Linus Torvalds
5f8fe4270e Merge branch 'for-linus' of git://repo.or.cz/cris-mirror
* 'for-linus' of git://repo.or.cz/cris-mirror:
  CRIS: Cleanup linker script using new linker script macros.
  ARRAY_SIZE changes
  CRIS: convert to asm-generic/hardirq.h
  CRISv10: Don't autonegotiate if autonegotiation is off
  CRIS: fix defconfig build failure
  CRIS: add pgprot_noncached
2009-09-24 17:08:56 -07:00
Russell King
baea7b946f Merge branch 'origin' into for-linus
Conflicts:
	MAINTAINERS
2009-09-24 21:22:33 +01:00
Benjamin Herrenschmidt
09dd3fc19c Fix build of cpm_uart due to core changes
Commit ebd2c8f6d2 "serial: kill off uart_info"

broke the build of this driver, this fixes it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-09-24 17:01:22 +10:00
Randy Dunlap
1b9894f342 serial core: fix new kernel-doc warnings
Fix new kernel-doc warnings in serial_core.[hc] files.

  Warning(include/linux/serial_core.h:485): No description found for parameter 'uport'
  Warning(include/linux/serial_core.h:485): Excess function parameter 'port' description in 'uart_handle_dcd_change'
  Warning(include/linux/serial_core.h:511): No description found for parameter 'uport'
  Warning(include/linux/serial_core.h:511): Excess function parameter 'port' description in 'uart_handle_cts_change'
  Warning(drivers/serial/serial_core.c:2437): No description found for parameter 'uport'
  Warning(drivers/serial/serial_core.c:2437): Excess function parameter 'port' description in 'uart_add_one_port'
  Warning(drivers/serial/serial_core.c:2509): No description found for parameter 'uport'
  Warning(drivers/serial/serial_core.c:2509): Excess function parameter 'port' description in 'uart_remove_one_port'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 11:24:57 -07:00
Anton Vorontsov
e0626e3844 spi: prefix modalias with "spi:"
This makes it consistent with other buses (platform, i2c, vio, ...).  I'm
not sure why we use the prefixes, but there must be a reason.

This was easy enough to do it, and I did it.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-09-23 07:39:43 -07:00
Russell King
ae19ffbadc Merge branch 'master' into for-linus 2009-09-22 21:01:40 +01:00
Russell King
28f9f19db9 Merge branch 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel 2009-09-21 16:02:30 +01:00
Peter Korsgaard
d2cfe9628c uartlite: support shared interrupt lines
Adapt isr to work with shared interrupt lines.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:38 -07:00
Deepak Saxena
ba15ab0e8d Set proper console speed on resume if console suspend is disabled
Commit b5b82df6, from May 2007, breaks no_console_suspend on the OLPC
XO laptop. Basically what happens is that upon returning from resume,
serial8250_resume_port() will reconfigure the port for high speed
mode and all console output will be garbled, making debug of the
resume path painful. This patch modifies uart_resume_port() to
reset the port to the state it was in before we suspended.

Original patch by Marcelo Tosatti

Second patch by Deepak then reworked by Alan to fit with the tty changes
before it got submitted. Also fixed the console path to set c_i/ospeed as
some drivers require the termios fields are valid

Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:33 -07:00
Alan Cox
7b01478f97 serial: introduce tty krefs
Initially just use the helper and thus krefs when we set and clear the
port values.

Signed-off-by: Alan Cox <alan@linux.intel.com>
2009-09-19 13:13:33 -07:00
Alan Cox
016af53a6d serial: kill USF_CLOSING_* definitions
The serial layer for some reason uses different defines for the special
case close delays and then conditionally switches to/from the normal ones
in the ioctls.

Remove this rather pointless abstraction

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:32 -07:00
Alan Cox
b58d13a021 serial: move port users helper
This little helper is now tty_port specific and useful generally so move it

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:32 -07:00
Alan Cox
bdc04e3174 serial: move delta_msr_wait into the tty_port
This is used by various drivers not just serial and can be extracted
as commonality

Signed-off-by: Alan Cox <alan@linux.intel.com>
2009-09-19 13:13:31 -07:00
Alan Cox
a2bceae065 serial: replace the state mutex with the tty port mutex
They cover essentially the same stuff and we can therefore fold it into the
tty_port one.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:31 -07:00
Alan Cox
ccce6debb6 serial: move the flags into the tty_port field
Fortunately the serial layer was designed to use the same flag values but
with different names. It has its own SUSPENDED flag which is a free slot in
the ASYNC flags so we allocate it in the ASYNC flags instead.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:30 -07:00
Alan Cox
91312cdb4f serial: move count into the tty_port version
Remove more stuff from the serial special case code

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:29 -07:00
Alan Cox
46d57a449a serial: use tty_port pointers in the core code
Extract out a lot of the x.port. uses and also show up where there are
things left to be isolated that prevent use using the port helpers in the
serial layer at this point

Signed-off-by: Alan Cox <alan@linux.intel.com>
2009-09-19 13:13:29 -07:00
Alan Cox
5e99df561f serial: Fold closing_* fields into the tty_port ones
Remove some more serial specific use

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-19 13:13:28 -07:00