New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.
New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.
New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support
Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=FxNN
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of IIO new device support, features and cleanups for the 4.8 cycle.
New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.
New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.
New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support
Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.
Removed unwanted return statements from the function
mma8452_set_freefall_mode.
Signed-off-by: Bijosh Thykkoottathil <bijosh.t@hotmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
mma8452_set_freefall_mode can return -ve value in case if
i2c_smbus_read_byte_data fails. This function is called from mma8452_probe,
and returning -ve value from probe indicates probe failure. Need to call
iio_triggered_buffer_cleanup & iio_trigger_cleanup in this case.
Signed-off-by: Bijosh Thykkoottathil <bijosh.t@hotmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Time to finally kill off the venerable (it was one of my first drivers)
lis3l02dq driver in favour of adding support in the st sensors framework.
This does loose us the event support that driver always had, but I think
that will reappear at some point and in the meantime the maintenance
advantages of dropping the 'special' driver for this one part outweigh
the issues.
It's worth noting this part is ancient and I may well be the only person
who still has any on hardware running recent kernels.
It has a few 'quirks'.
- No WAI register so that just became optional.
- A BDU option that really does block updates. Completely.
Whatever you do, you don't get any more data with it set.
It is documented the same as more modern parts but I presume they
are actually clearing for updates after a read of both bytes!
- Fixed scale.
- It's too quick. Even at slowest rate (280Hz) I can't read out fast
enough on my board (stargate 2) to beat new data coming in. Linus'
repeat read patch doesn't help in this case. It just means I get 10
readings before dying... So in reality this will get used with
software triggers only unless someone has this long out of production
device on a quick board.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Adds a new per-device sysfs attribute "current_timestamp_clock" to allow
userspace to select a particular POSIX clock for buffered samples and
events timestamping.
Following clocks, as listed in clock_gettime(2), are supported:
CLOCK_REALTIME, CLOCK_MONOTONIC, CLOCK_MONOTONIC_RAW,
CLOCK_REALTIME_COARSE, CLOCK_MONOTONIC_COARSE, CLOCK_BOOTTIME and
CLOCK_TAI.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6Lja
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of new iio device support, features and cleanups in the 4.8 cycle
Firstly some contact detail updates:
* NXP took over freescale. Update the mma8452 header to reflect this.
* Martin Kepplinger email address change in mma8452 header.
* Adriana Reus has changed email address. Update .mailmap.
* Matt Ranostay has changed email address. Update .mailmap.
New Device Support
* max1363
- add the missing i2c_device_ids for a couple of parts so they can actually
be used.
* ms5867
- add device ids for ms5805 and ms5837 parts.
New Features
* ad5755
- DT support. This one was a bit controversial and under review for a long
time. Still no one could come up with a better solution.
* stx104
- add gpio support
* ti-adc081c
- Add ACPI device ID matching.
Core changes
* Refuse to register triggers with duplicate names. There is no way to
distinguish between them so this makes no sense. A few drivers do not
generate unique names for each instance of the device present. We can't
fix this without changing ABI so leave them and wait for someone to
actually take the rare step of two identical accelerometers on the same
board.
* buffer-dma
- use ARRAY_SIZE in a few appropriate locations.
Tools
* Fix the fact that the --trigger-num option in generic_buffer didn't allow
0 which is perfectly valid in the ABI.
Cleanups
* as3935
- improve error reporting.
- remove redundant zeroing of a field in iio_priv.
* gp2ap020a00f
- use the iio_device_claim_*_mode helpers rather than open coding locking
around mode changes.
* isl29125
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* lidar
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* mma8452
- more detail in devices supported description in comments (addresses and
similar)
* sca3000
- add a missing error check.
* tcs3414
- use the iio_device_claim_*_mode helpers rather than open coding locking.
* tcs3472
- use the iio_device_claim_*_mode helpers rather than open coding locking.
These two spi_w8r8() calls return a value with is used by the code
following the error check. The dubious use was caused by a cleanup
patch.
Fixes: d34dbee8ac ("staging:iio:accel:kxsd9 cleanup and conversion to iio_chan_spec.")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in here, and we can resolve a merge issue in
drivers/iio/industrialio-trigger.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NXP took over Freescale, so add NXP to the driver descriptions
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Hq1a
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.8a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.8 cycle.
New device support
* ads1015
- add ads1115 support
* bma220 accelerometer
- new driver
- triggered buffer support.
* bmc150
- add bmm150 support.
* bmp280
- bme280 support with addition of humidity channel.
* max5487 potentiometer
- new driver
* MMA7660FC accelerometer.
- New driver
* st-pressure
- support for the lps22hb
* loop trigger.
- This one is *nasty* but we have real applications (parrot drones) where
it is useful. The trigger basically spins as hard as it can firing off
a new trigger each time all triggered devices come back to say they are
done. It doesn't hang a machine even when doing it on a dummy driver.
A lot nicer than having this implemented within lots of device drivers
anyway.
Core stuff
* Add support to create IIO devices via configfs (similar to we did for
triggers a while back) + docs.
* New channel types
- IIO_ELECTRICAL_CONDUCTIVITY
* Couple of MAINTAINERS patches to list the device tree bindings.
* Make trigger ops structure non optional (comment fix). It hasn't been for
an awful long time, but that's not what the description said.
New features
* ak8975
- support adapters that are limited to byte data only by allowing the
emulated block read i2c function that was recently introduced.
* atlas-ph
- support atlas-ec (electrical conductivity sensor)
* bmi160
- add available frequency and scale attributes to make the driver
more user friendly (and avoid having to read the datasheet to know
what will work).
* dummy
- move creation to configfs interface. It's not real hardware so we
are not that worried about the ABI breakage ;)
* mma8452
- oversampling ration support
* nau7802
- expose available gains to make life easier for userspace.
* st-sensors
- allow use of emulation for SMBus block reads as all the st parts support
it.
* ti-ads1015
- list datasheet names to allow their use by inkernel consumers.
* Various module alias additions to help auto probing. Drop one redundant one
as well.
Cleanups
* ad7266, ad7476, ad7887, ad7923, ad799x
- use direct mode claim function rather than open coding it during sensor
read (prevents switching on buffers mid read).
* ad7793, ad7791
- use direct mode claim to prevent frequency changes when buffers running.
* afe440x - These are ABI breaking but the driver requires custom userspace
code to do anything useful anyway and that is still being written and under
control of TI. Ultimately we may have other libraries to do pulse
oximetry with these devices but we aren't aware of any yet.
- kernel-doc format fixes
- drop ifdef fun around of_match_ptr - it's not worth the mess to save
a tiny amount of space.
- drop some unnecessary register initializations.
- drop the weird locked gain modes as they gain us nothing (can just set
all gains separately).
- remove handling of offset attributes seeing as no channels actually have
them (oops)
- Drop the LED3 input channel as it's an alias for ALED2.
- *big one* remove channel names - an experiment that turned out to not
make sense - see patch for details.
- use regmap fields to clean up code.
- tie the tia gain stages to appropriate channels in the ABI as that is
what they really effect. Same with the LED currents.
- cleanout some unused defines and fix a missnamed one.
* atlas-ph
- reorganise to allow support of other similar parts.
* bmc150
- document supported chips in kconfig help.
* jsa1212
- drop an unneeded i2c functionality check for functionality the driver
doesn't use.
* mxs-lradc
- simply touch screen registration code.
- remove the touch screen unregister as all devm based now.
- disable only those channels that are masked in hardware stop (others
are already dealt with elsewhere)
* st-sensors
- unexport st_sensors_get_buffer_element as nothing outside the st-sensors
core driver uses it.
- fix handling of failure to start up regulators.
* tpl0102
- drop an i2c functionality test for features that aren't needed.
* ti-am335x
- use variable name rather than type in sizeof for clarity.
- use SIMPLE_DEV_PM_OPS helper macro to tidy up a bit.
Tools
* Add install / uninstall to makefile. Someone cares, so presumably
some people will find it useful!
* generic_buffer
- rename to iio_generic_buffer to line up with other tools.
- handle cleanup when receiving signals
- Add a --device-num option and a --trigger-num option rather than
relying on naming which doesn't work if you have two of the same part.
commit 98ad8b41f58dff6b30713d7f09ae3834b8df7ded
("iio: st_sensors: verify interrupt event to status") caused
a regression when reading ST sensors from a HRTimer trigger
rather than the intrinsic interrupts: the HRTimer may
trigger faster than the sensor provides new values, and
as the check against new values available as a cause of
the interrupt trigger was done in the poll function,
this would bail out of the HRTimer interrupt with
IRQ_NONE.
So clearly we need to only check the new values available
from the proper interrupt handler and not from the poll
function, which should rather just read the raw values
from the registers, put them into the buffer and be happy.
To achieve this: switch the ST Sensors over to using a true
threaded interrupt handler.
In the interrupt thread, check if new values are available,
else yield to the (potential) next device on the same
interrupt line to check the registers. If the interrupt
was ours, proceed to poll the values.
Instead of relying on iio_trigger_generic_data_rdy_poll() as
a top half to wake up the thread that polls the sensor for
new data, have the thread call iio_trigger_poll_chained()
after determining that is is the proper source of the
interrupt. This is modelled on drivers/iio/accel/mma8452.c
which is already using a properly threaded interrupt handler.
In order to get the same precision in timestamps as
previously, where samples would be timestamped in the
poll function pf->timestamp when calling
iio_trigger_generic_data_rdy_poll() we introduce a
local timestamp in the sensor data, set it in the top half
(fastpath) of the interrupt handler and provide that to the
core when calling iio_push_to_buffers_with_timestamp().
Additionally: if the active scanmask is not set for the
sensor no IRQs should be enabled and we need to bail out
with IRQ_NONE. This can happen if spurious IRQs fire when
installing the threaded interrupt handler.
Tested with hard interrupt triggers on LIS331DL, then also
tested with hrtimers on the same sensor by creating a 75Hz
HRTimer and using it to poll the sensor.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Tested-by: Jonathan Cameron <jic23@kernel.org>
Fixes: 97865fe413 ("iio: st_sensors: verify interrupt event to status")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ensure failure to enable power regulators is properly handled.
Signed-off-by: Gregor Boirie <gregor.boirie@parrot.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit adds basic support for the Bosch Sensortec BMA220
digital triaxial acceleration sensor.
The device datasheet can be found here:
http://www.mouser.com/pdfdocs/BSTBMA220DS00308.PDF
Includes:
- raw readings
- ACPI detection
- power management
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds the following sysfs files according to the iio ABI:
-rw-r--r-- 4096 in_accel_oversampling_ratio
-r--r--r-- 4096 in_accel_oversampling_ratio_available
Internally, the device knows about 4 different power modes that differ
in oversampling ratio (and power consumption). We just show the user
what oversampling ratio(s) is/are available, depending on the current
frequency.
The referenced table in the datasheets makes it easier to understand.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation of an IIO driver for the Freescale
MMA7660FC 3-axis accelerometer. Datasheet:
http://www.nxp.com/files/sensors/doc/data_sheet/MMA7660FC.pdf
Includes:
- ACPI support;
- read_raw for x,y,z axes;
- reading and setting the scale (range) parameter.
- power management
Signed-off-by: Constantin Musca <constantin.musca@intel.com>
Reviewed-by: Martin Klepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zzV9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.
Bit of a bumper set for new drivers but plenty of other stuff here as well!
New device support
* ad5592R ADC/DAC
- new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
- new driver with triggered buffer support in follow up patch.
* bmi160 imu
- new driver
* bmp280
- bmp180 support - note there is support in the misc/bmp085 driver. Intent
is to remove that driver long term.
* invensense mpu6050
- cleanup leading to explicit support of mpu9150 with a good few cleanups
along the way.
* Hope RF hp03 pressure and temperature sensor.
- new driver
* maxim DS1803 potentiometer
- new driver
* maxim max44000 light and proximity sensor
- new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
- new driver. There is an existing driver in misc that this is pretty much
intended to replace. The discussion on whether to support the non standard
interface of that driver is some way is continuing.
* st-gyro
- lsm9ds0-gyro. The accel/magn side of this will take a while longer as
extensions to the st library are needed for cases where two types of sensor
share a single i2c address.
* ti-adc081c
- support the adc101c and adc121c
* Vishay VEML6070 UV sensor
- new driver.
New features
* core
- devm_ APIs for channel_get and channel_get_all. The first user of these
is the generic ADC based thermal driver. As it is going through the
thermal tree these will be picked up as a patch to that next cycle as that
is how the author preferred to do it.
- mounting matrix support. This new core support allows devices to provide
to userspace (typically from the device tree) allowing compensation for how
the sensor is mounted on the device. First examples are on UAVs but it
has a more mundane use on typical phone where the chip may be on the front
or the back of the circuit board and soldered at any angle. Includes
support for this ABI in ak8975 (which has an older interface, now
deprecated) and mpu6050.
* tools
- add a -a option to enable all available channels in generic_buffer sample.
Makes it somewhat easier to use.
* adis library and drivers
- support manual self test flag clearing. This has technically been broken
for a very long time - result is an offset on readings as the applied field
is on all the time.
* ak8975
- triggered buffer support
* bmc150
- spi support (including splitting the driver into core and i2c parts)
* bmp280
- oversampling support.
* dht11
- improved logging - useful to debug timing issues on this quirky device.
* st-sensors
- read each channel invidivually as not all support the optimization of
reading in bulk. This is technically a fix, but will need to be backported
if desired.
- support open drain and shared interrupts.
* ti-adc081c
- triggered buffer support.
Cleanups
* inkern
- white space fix.
* ad7606
- use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
- white space fix.
* ad9523
- unsigned -> unsigned int
* apds9660
- brace location tidying up.
- silence an uninitialized variable warning.
* ak8975
- else and brace on same line fix.
* at91_adc
- white space fixes.
* bmc150
- use regmap stored copy of the device pointer rather than having an
additional copy.
* bmg160
- use regmap stored copy of the device pointer rather than having an
additional copy.
* hid-sensors
- white space fixes.
* mcp3422
- white space fix.
* mma7455
- use regmap to retrieve the device struct rather than carrying another copy
in the private data.
* ms_sensors
- white space fix.
* mxs-lradc
- move current bindings out of staging - some will be shortly deprecated but
the reality is that we have device trees out there using them so they will
need to be supported for some time. They accidentally got left behind
when the driver graduated from staging.
- white space cleanup.
- set INPUT_PROP_DIRECT.
- move ts config into a better function.
- move the STMP reset out of the ADC init.
* vf610_adc
- case label indenting fix.
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some types of ST Sensors can be connected to the same IRQ line
as other peripherals using open drain. Add a device tree binding
and a sensor data property to flip the right bit in the interrupt
control register to enable open drain mode on the INT line.
If the line is set to be open drain, also tag on IRQF_SHARED
to the IRQ flags when requesting the interrupt, as the whole
point of using open drain interrupt lines is to share them with
more than one peripheral (wire-or).
Cc: devicetree@vger.kernel.org
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This makes all ST sensor drivers check that they actually have
new data available for the requested channel(s) before claiming
an IRQ, by reading the status register (which is conveniently
the same for all ST sensors) and check that the channel has new
data before proceeding to read it and fill the buffer.
This way sensors can share an interrupt line: it can be flaged
as shared and then the sensor that did not fire will return
NO_IRQ, and the sensor that fired will handle the IRQ and
return IRQ_HANDLED.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves a lot of merge issues with PAGE_CACHE_* changes, and an
iio driver merge issue.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver includes struct regmap and struct device in its global data.
Remove the struct device and use regmap API to retrieve device info.
Patch created using Coccinelle plus manual edits.
Signed-off-by: Alison Schofield <amsfield22@gmail.com>
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
bmc150_i2c_regmap_conf is defined three times (in bmc150-accel-core.c,
bmc150-accel-i2c.c and and bmc150-accel-spi.c), although the
definition is the same.
Use one common definition for bmc150_i2c_regmap_conf in all
included files.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For big endian platforms, reading the axes will return
invalid values.
The device stores each axis value in a 16 bit little
endian register. The driver uses regmap_read_bulk to get
the axis value, resulting in a 16 bit little endian value.
This needs to be converted to cpu endianness to work
on big endian platforms.
Fix endianness for big endian platforms by converting
the values for the axes read from little endian to
cpu.
This is also partially fixed in commit b6fb9b6d6552 ("iio:
accel: bmc150: optimize transfers in trigger handler").
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 845c877009 ("i2c / ACPI: Assign IRQ for devices that have
GpioInt automatically") automatically assigns the first ACPI GPIO
interrupt in client->irq, so we can remove the probing code from
drivers that use only one interrupt.
Commit 0f0796509c ("iio: remove gpio interrupt probing from drivers
that use a single interrupt") removes gpio interrupt probing from most
drivers. This patch cleans the remaining ones.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
GPIO handling code has been removed from the drivers (since
this is now handled by the ACPI core) in commit 0f0796509c ("iio:
remove gpio interrupt probing from drivers that use a single interrupt").
Remove the include for linux/gpio/consumer.h since it is no longer
used.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the kxcjk-1013 accel driver
does one i2c transfer for each axis. This has an impact on the
frequency of the accelerometer at high sample rates due to additional
delays introduced by the i2c bus at each transfer.
Reading all axis values in one i2c transfer reduces the delays
introduced by the i2c bus. Uses i2c_smbus_read_i2c_block_data_or_emulated
that will fallback to reading each axis as a separate word in case i2c
block read is not supported.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some i2c busses (e.g.: Synopsys DesignWare I2C adapter) need to
enable/disable the bus at each i2c transfer and must wait for
the enable/disable to happen before sending the data.
When reading data in the trigger handler, the bmc150 accel driver does
one bus transfer for each axis. This has an impact on the frequency
of the accelerometer at high sample rates due to additional delays
introduced by the bus at each transfer.
Reading all axis values in one bus transfer reduces the delays
introduced by the bus.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use available_scan_masks to allow the iio core to select
the data to send to userspace depending on which axes are
enabled, instead of doing this in the driver's interrupt
handler.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
What is this autosleep?
-----------------------
It slows down the device after x seconds of inactivity. The thing is, we have
really achieved almost the same by runtime pm.
differnces are:
autosleep
* uses more power during inactivity
* the first read after inactivity slightly faster
* complicated to understand for the user
* no documented sysfs interface (afaik)
* complicated to read and maintain
runtime pm
* already merged in mma8452
* uses less power during inactivity
* first read after inactivity slower
* easy to use. well documented.
* easy to maintain and understand
The two approaches solve the same problem. runtime pm has more advantages
than autosleep and comes quite close to it's behaviour anyways. As I see it,
autosleep, even if somehow supported, would never be used anyways.
So resolve this issue by "ignoring" autosleep.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Reviewed-by: Martina Kepplinger <martina.novakovic@zoho.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This was forgotten about and is added for consistency now
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for Freescale's (now NXP's) FXLS8471Q accelerometer.
We use MMA8451Q's configuration because for what the driver supports,
FXLS8471Q is the same.
Support for FXLS8471Q's features (fast SPI interface and a larger FIFO,
among others) can be added to this driver anytime.
See it's datasheet for the details:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXLS8471Q.pdf
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This commit adds support for STMicroelectronics h3lis331dl high-g
accelerometer. The datasheet for this device can be found here:
http://www.st.com/web/en/resource/technical/document/
datasheet/DM00053090.pdf
Signed-off-by: Tiberiu Breana <tiberiu.a.breana@intel.com>
Reviewed-by: Denis Ciocca <denis.ciocca@st.com>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for runtime power management and, if configured, activates
automatic standby after 2 seconds of inactivity.
Inactivity means no read of acceleration values and no events triggered or
activated.
If CONFIG_PM is not set, this doesn't change anything for existing users.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The devices' config registers can only be changed in standby mode.
Up until now the driver just held the device *always* active, so for
changing a config it was *always* necessary to switch to standby.
For upcoming support for runtime pm, the device can as well be in standby
mode. Instead of putting runtime pm functions in there, just keep the
device in standby if it already is. This section is protected by a lock
after all.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
fix checkpatch issues like "space before tabs", too long lines or alignment.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This set comprises those not dependent on patches in the 4.5 merge cycle.
A second set will follow shortly with ones that are.
* core in kernel interfaces
- fix a possible NULL dereference that is a theoretical possibility
via odd usage of iio_channel_release. Pretty much a hardening of
the interface, but observed in the wild with the twl4030_charger
driver.
* acpi-als
- report the data as processed as it is in lux. This fixes a wrong
use of the IIO ABI. However, old _raw version retained to avoid
breaking any userspace in the wild that is relying on that (none
known but it doesn't hurt us much to retain it)
* ade7753
- fix some error handling to avoid use of unitialized data.
* ltr501
- use a signed return type for ltr501_match_samp_freq so as to allow
returning of an error code.
* mcp4725
- set name field of struct iio_dev to ensure the sysfs name attribute
doesn't give NULL.
* mpl115
- temperature offset sign is wrong.
* stk8ba50
- IIO_TRIGGER dependency added
* ti_am335x_adc
- Label buffer as a software buffer. It's actually a hybrid of a
true hardware buffer feeding a kfifo, but the meaning of these fields
has changed a little recently and in this case it should be labeled
a software buffer ensure it is allowed to use the kfifo.
* vf610_adc
- HAS_IOMEM dependency
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=27Pv
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.5 cycle.
This set comprises those not dependent on patches in the 4.5 merge cycle.
A second set will follow shortly with ones that are.
* core in kernel interfaces
- fix a possible NULL dereference that is a theoretical possibility
via odd usage of iio_channel_release. Pretty much a hardening of
the interface, but observed in the wild with the twl4030_charger
driver.
* acpi-als
- report the data as processed as it is in lux. This fixes a wrong
use of the IIO ABI. However, old _raw version retained to avoid
breaking any userspace in the wild that is relying on that (none
known but it doesn't hurt us much to retain it)
* ade7753
- fix some error handling to avoid use of unitialized data.
* ltr501
- use a signed return type for ltr501_match_samp_freq so as to allow
returning of an error code.
* mcp4725
- set name field of struct iio_dev to ensure the sysfs name attribute
doesn't give NULL.
* mpl115
- temperature offset sign is wrong.
* stk8ba50
- IIO_TRIGGER dependency added
* ti_am335x_adc
- Label buffer as a software buffer. It's actually a hybrid of a
true hardware buffer feeding a kfifo, but the meaning of these fields
has changed a little recently and in this case it should be labeled
a software buffer ensure it is allowed to use the kfifo.
* vf610_adc
- HAS_IOMEM dependency
This adds support for this series' 14 bit accelerometer chip, MMA8451Q.
It's datasheet is available at the vendor's website:
https://cache.freescale.com/files/sensors/doc/data_sheet/MMA8451Q.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds freefall event detection to the supported devices. It adds
the in_accel_x&y&z_mag_falling_en iio event attribute, which activates
freefall mode.
In freefall mode, the current acceleration magnitude (AND combination
of all axis values) is compared to the specified threshold.
If it falls under the threshold (in_accel_mag_falling_value),
the appropriate IIO event code is generated.
This is what the sysfs "events" directory for these devices looks
like after this change:
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_falling_value
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_period
-rw-r--r-- 4096 Oct 23 08:45 in_accel_mag_rising_value
-r--r--r-- 4096 Oct 23 08:45 in_accel_scale
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x&y&z_mag_falling_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_x_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_y_mag_rising_en
-rw-r--r-- 4096 Oct 23 08:45 in_accel_z_mag_rising_en
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Most ST MEMS Sensors that support interrupts can also handle sending
an active low interrupt, i.e. going from high to low on data ready
(or other interrupt) and thus triggering on a falling edge to the
interrupt controller.
Set up logic to inspect the interrupt line we get for a sensor: if
it is triggering on rising edge, leave everything alone, but if it
triggers on falling edges, set up active low, and if unsupported
configurations appear: warn with errors and reconfigure the interrupt
to a rising edge, which all interrupt generating sensors support.
Create a local header for st_sensors_core.h to share functions
between the sensor core and the trigger setup code.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Ran into this on UML:
drivers/iio/accel/stk8ba50.c: In function ‘stk8ba50_data_rdy_trigger_set_state’:
drivers/iio/accel/stk8ba50.c:163:9: error: implicit declaration of function ‘iio_trigger_get_drvdata’ [-Werror=implicit-function-declaration]
iio_trigger_get_drvdata() is defined only when IIO_TRIGGER is selected.
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This gets rid of some magic numbers by adding an enum.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CfCl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.5 cycle
Usual mixed bag, but the big item perhaps in this series is the DMA buffer
support added by Lars-Peter Clausen. It's been in the works for a long time
and it will be interesting to see what hardware support shows up now that
this is available.
New core features + associate cleanup.
* Add generic DMA buffer infrastructure
* Add a DMAengine framework based buffer
Also associated minor changes.
- Set the device buffer watermark based on the minimum watermark for all
attached buffers rather than just the 'primary' one.
- iio_buffer_init - only set the watermark default if one hasn't already
been provided. This allows simple support for devices with a fixed
watermark.
- read only attribute for watermark on fixed watermark devices.
- add explicit buffer enable/disable callbacks to allow the buffer to
do more than trivial actions when it is being turned on and off.
* IIO_VAL_INT support in write_raw_get_fmt function.
New device support
* Freescale MMA7455/7456L accelerometers
* Memsic MXC6255XC accelerometer
* ST lis2dh12 accelerometer
* TI ADS8688 ADC
* TI Palamas (twl6035/7) gpadc
New driver features
* mma8452
- support either of the available interrupt pins to cope with the case
where board layout has lead to a particular one being connected.
Staging graduation
* Dummy driver
- this driver acts as both an example and a test device for those with
out hardware to develop userspace code against.
Cleanups and minor bits and bobs.
* treewide
- Sort out the ordering of iio_device_register/unregister vs runtime
pm function calls so that it's all nice and consistent and not race
prone.
- Check sscanf return values. None of the cases will actually happen as
the strings are supplied internally, but best to be consistent on this.
* ad7780
- switch over to the gpio descriptor interface and remove the now unused
platform data which gets rid of a header entirely.
* ad7793
- drop a pointless else statement.
* at91_adc
- Swap kmalloc_array in for a kmalloc doing the same job.
* dummy
- get rid of some commented out lines that snuck in during the move of
the driver.
* lm3533-als
- Print an error message on provision of an invalid resistance.
* mcp320x
- Add compatible strings with vendor prefix and deprecate those with
no vendor prefix.
* mxs-lradc
- Use BIT macro in various places rather than shifted ones.
* pa12203001
- Power off the chip if the registration fails.
* pulsedlight-lidar-lite
- add runtime PM support.
* xilinx XADC
- constify an iio_buffer_setup_ops structure.
