Current mac80211 has provision to update tx status through
ieee80211_tx_status() and ieee80211_tx_status_ext(). But
drivers like ath10k updates the tx status from the skb except
txrate, txrate will be updated from a different path, peer stats.
Using ieee80211_tx_status_ext() in two different paths
(one for the stats, one for the tx rate) would duplicate
the stats instead.
To avoid this stats duplication, ieee80211_tx_rate_update()
is implemented.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
[minor commit message editing, use initializers in code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.
Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When there are few packets (e.g. for sampling attempts), the exponentially
weighted variance is usually vastly overestimated, making the resulting data
essentially useless. As far as I know, there has not been any practical use
for this, so let's not waste any cycles on it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These rates are highly unlikely to be used quickly, even if the link
deteriorates rapidly. This improves throughput in cases where CCK rates
are not reliable enough to be skipped entirely during sampling.
Sampling these rates regularly can cost a lot of airtime.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Long/short preamble selection cannot be sampled separately, since it
depends on the BSS state. Because of that, sampling attempts to
currently not used preamble modes are not counted in the statistics,
which leads to CCK rates being sampled too often.
Fix statistics accounting for long/short preamble by increasing the
index where necessary.
Fix excessive CCK rate sampling by dropping unsupported sample attempts.
This improves throughput on 2.4 GHz channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a harmless underflow issue when CCK rates are actively being used
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mi->supported[MINSTREL_CCK_GROUP] needs to be updated
short preamble rates need to be marked as supported regardless of
whether it's currently enabled. Its state can change at any time without
a rate_update call.
Fixes: 782dda00ab ("mac80211: minstrel_ht: move short preamble check out of get_rate")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By storing a shift value for all duration values of a group, we can
reduce precision by a neglegible amount to make it fit into a u16 value.
This improves cache footprint and reduces size:
Before:
text data bss dec hex filename
10024 116 0 10140 279c rc80211_minstrel_ht.o
After:
text data bss dec hex filename
9368 116 0 9484 250c rc80211_minstrel_ht.o
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy-only devices are not very common and the overhead of the extra
code for HT and VHT rates is not big enough to justify all those extra
lines of code to make it optional.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
debugfs entries are cleaned up by debugfs_remove_recursive already.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If peer support reception of STBC and LDPC, enable them for better
performance.
Signed-off-by: Chaitanya TK <chaitanya.mgit@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I'm not really sure exactly _why_ I've been carrying a note
for what's probably _years_ to check that we don't do this,
but we clearly do reflect frames back to the station itself
if it sends such.
One way or the other, it's useless since the station doesn't
really need the AP to talk to itself, so suppress it.
While at it, clarify some of the logic by removing skb->data
references in favour of the destination address (pointer) we
already have separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge net-next, which pulled in net, so I can merge a few more
patches that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable j will be initialized at trailing step.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code -ENOMEM from the kmemdup
error handling case instead of 0.
Fixes: 09b4a4faf9 ("mac80211: introduce capability flags for VHT EXT NSS support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that do not have the BUFF_MMPDU_TXQ flag set will not have a
TXQ for the special TID = 16.
In this case, the last member in the *struct ieee80211_sta* txq array
will be NULL.
We must check this in order not to get a NULL pointer dereference when
iterating the txq array.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
key->sta is only valid after ieee80211_key_link, which is called later
in this function. Because of that, the IEEE80211_KEY_FLAG_RX_MGMT is
never set when management frame protection is enabled.
Fixes: e548c49e6d ("mac80211: add key flag for management keys")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Monitor mode interfaces with the active flag are passed down to the driver.
Drivers using TXQ expect that all interfaces have allocated TXQs before
they get added.
Fixes: 79af1f8661 ("mac80211: avoid allocating TXQs that won't be used")
Cc: stable@vger.kernel.org
Reported-by: Catrinel Catrinescu <cc@80211.de>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TX status reporting to ieee80211s is through ieee80211s_update_metric.
There are two problems about ieee80211s_update_metric:
1. The purpose is to estimate the fail probability
to a specific link. No need to restrict to data frame.
2. Current implementation does not work if wireless driver does not
pass tx_status with skb.
Fix this by removing ieee80211_is_data condition, passing
ieee80211_tx_status directly to ieee80211s_update_metric, and
putting it in both __ieee80211_tx_status and ieee80211_tx_status_ext.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the TDLS setup happens over a connection to an AP that
doesn't have QoS, we nevertheless assign a non-zero TID
(skb->priority) and queue mapping, which may confuse us or
drivers later.
Fix it by just assigning the special skb->priority and then
using ieee80211_select_queue() just like other data frames
would go through.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In our environment running lots of mesh nodes, we are seeing the
pending queue hang periodically, with the debugfs queues file showing
lines such as:
00: 0x00000000/348
i.e. there are a large number of frames but no stop reason set.
One way this could happen is if queue processing from the pending
tasklet exited early without processing all frames, and without having
some future event (incoming frame, stop reason flag, ...) to reschedule
it.
Exactly this can occur today if ieee80211_tx() returns false due to
packet drops or power-save buffering in the tx handlers. In the
past, this function would return true in such cases, and the change
to false doesn't seem to be intentional. Fix this case by reverting
to the previous behavior.
Fixes: bb42f2d13f ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Both old and new cannot be NULL at the same time, hence checking
new when old is not NULL is unnecessary.
Also, notice that new is being dereferenced before it is checked:
idx = new->conf.keyidx;
The above triggers a static code analysis warning.
Address this by removing the NULL check on new and adding a code
comment based on the following piece of code:
387 /* caller must provide at least one old/new */
388 if (WARN_ON(!new && !old))
389 return 0;
Addresses-Coverity-ID: 1473176 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some hardwares have limitations on the packets' type in AMSDU.
Add an optional driver callback to determine if two skbs can
be used in the same AMSDU or not.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may have AMSDU size limitation per TID, due to
HW constrains. Add an option to set this limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We have a TXQ abstraction for non-data packets that need
powersave buffering. Since the AP cannot sleep, in case
of station we can use this TXQ for all management frames,
regardless if they are bufferable. Add HW flag to allow
that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise the offchannel frame might be queued due to
IEEE80211_QUEUE_STOP_REASON_PS and later dropped (in
ieee80211_tx_frags()). Anyway, it doesn't make much sense to wake up
the device during ROC.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a frame is dropped for any reason, mac80211 wouldn't report the TX
status back to user space.
As the user space may rely on the TX_STATUS to kick its state
machines, resends etc, it's better to just report this frame as not
acked instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:
1) Freeze caused by incoming frames:
If the local STA installed the key prior to the remote STA we still
had the old key active in the hardware when mac80211 switched over
to the new key.
Therefore there was a window where the card could hand over frames
decoded with the old key to mac80211 and bump the new PN (IV) value
to an incorrect high number. When it happened the local replay
detection silently started to drop all frames sent with the new key.
2) Freeze caused by outgoing frames:
If mac80211 was providing the PN (IV) and handed over a clear text
frame for encryption to the hardware prior to a key change the
driver/card could have processed the queued frame after switching
to the new key. This bumped the PN value on the remote STA to an
incorrect high number, tricking the remote STA to discard all frames
we sent later.
3) Freeze caused by RX aggregation reorder buffer:
An aggregation session started with the old key and ending after the
switch to the new key also bumped the PN to an incorrect high number,
freezing the connection quite similar to 1).
4) Freeze caused by repeating lost frames in an aggregation session:
A driver could repeat a lost frame and encrypt it with the new key
while in a TX aggregation session without updating the PN for the
new key. This also could freeze connections similar to 2).
5) Clear text leak:
Removing encryption offload from the card cleared the encryption
offload flag only after the card had deleted the key and we did not
stop TX during the rekey. The driver/card could therefore get
unencrypted frames from mac80211 while no longer be instructed to
encrypt them.
To prevent those issues the key install logic has been changed:
- Mac80211 divers known to be able to rekey PTK0 keys have to set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
- mac80211 stops queuing frames depending on the key during the replace
- the key is first replaced in the hardware and after that in mac80211
- and mac80211 stops/blocks new aggregation sessions during the rekey.
For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.
The core of the fix changes the key install procedure from:
- atomic switch over to the new key in mac80211
- remove the old key in the hardware (stops encryption offloading, fall
back to software encryption with a potential clear text packet leak
in between)
- delete the inactive old key in mac80211
- enable hardware encryption offloading for the new key
to:
- if it's a PTK mark the old key as tainted to drop TX frames with the
outgoing key
- replace the key in hardware with the new one
- atomic switch over to the new (not marked as tainted) key in
mac80211 (which also resumes TX)
- delete the inactive old key in mac80211
With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.
For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.
The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.
Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.
When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.
Also, since it was missing, copy tx_highest and rx_highest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.
If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Export HE capabilities information via debugfs, similar to HT & VHT.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----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=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When tracing is enabled, all the debug messages are recorded and must
not exceed MAX_MSG_LEN (100) columns. Longer debug messages grant the
user with:
WARNING: CPU: 3 PID: 32642 at /tmp/wifi-core-20180806094828/src/iwlwifi-stack-dev/net/mac80211/./trace_msg.h:32 trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Workqueue: phy1 ieee80211_iface_work [mac80211]
RIP: 0010:trace_event_raw_event_mac80211_msg_event+0xab/0xc0 [mac80211]
Call Trace:
__sdata_dbg+0xbd/0x120 [mac80211]
ieee80211_ibss_rx_queued_mgmt+0x15f/0x510 [mac80211]
ieee80211_iface_work+0x21d/0x320 [mac80211]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
