Currently status frames are only handled when packet timestamping is
enabled, but status frames are also needed for pin event timestamping.
Fix by moving packet timestamping check to after status frame decode.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netlink_dump() returns a negative errno value on error. Until now,
netlink_recvmsg() directly recorded that negative value in sk->sk_err, but
that's wrong since sk_err takes positive errno values. (This manifests as
userspace receiving a positive return value from the recv() system call,
falsely indicating success.) This bug was introduced in the commit that
started checking the netlink_dump() return value, commit b44d211 (netlink:
handle errors from netlink_dump()).
Multithreaded Netlink dumps are one way to trigger this behavior in
practice, as described in the commit message for the userspace workaround
posted here:
http://openvswitch.org/pipermail/dev/2014-June/042339.html
This commit also fixes the same bug in netlink_poll(), introduced in commit
cd1df525d (netlink: add flow control for memory mapped I/O).
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is recommended that TX work not count against the quota.
The cost of TX packet liberation is a minute percentage of what it costs to
process an RX frame. Furthermore, that SKB freeing makes memory available for
other paths in the stack.
Give the TX a larger budget and be more aggressive about cleaning up the Tx
descriptors this budget could be changed using ethtool:
$ ethtool -C eth1 tx-frames-irq <budget>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting just skb->sk without taking its reference and setting a
destructor is invalid. However, in the places where this was done, skb
is used in a way not requiring skb->sk setting. So dropping the setting
of skb->sk.
Thanks to Eric Dumazet <eric.dumazet@gmail.com> for correct solution.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79441
Reported-by: Ed Martin <edman007@edman007.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes 3 similar bugs where incoming packets might be routed into
wrong non-wildcard tunnels:
1) Consider the following setup:
ip address add 1.1.1.1/24 dev eth0
ip address add 1.1.1.2/24 dev eth0
ip tunnel add ipip1 remote 2.2.2.2 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets from 2.2.2.2 were routed into ipip1 even if it has dst =
1.1.1.2. Moreover even if there was wildcard tunnel like
ip tunnel add ipip0 remote 2.2.2.2 local any mode ipip dev eth0
but it was created before explicit one (with local 1.1.1.1), incoming ipip
packets with src = 2.2.2.2 and dst = 1.1.1.2 were still routed into ipip1.
Same issue existed with all tunnels that use ip_tunnel_lookup (gre, vti)
2) ip address add 1.1.1.1/24 dev eth0
ip tunnel add ipip1 remote 2.2.146.85 local 1.1.1.1 mode ipip dev eth0
ip link set ipip1 up
Incoming ipip packets with dst = 1.1.1.1 were routed into ipip1, no matter what
src address is. Any remote ip address which has ip_tunnel_hash = 0 raised this
issue, 2.2.146.85 is just an example, there are more than 4 million of them.
And again, wildcard tunnel like
ip tunnel add ipip0 remote any local 1.1.1.1 mode ipip dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
Gre & vti tunnels had the same issue.
3) ip address add 1.1.1.1/24 dev eth0
ip tunnel add gre1 remote 2.2.146.84 local 1.1.1.1 key 1 mode gre dev eth0
ip link set gre1 up
Any incoming gre packet with key = 1 were routed into gre1, no matter what
src/dst addresses are. Any remote ip address which has ip_tunnel_hash = 0 raised
the issue, 2.2.146.84 is just an example, there are more than 4 million of them.
Wildcard tunnel like
ip tunnel add gre2 remote any local any key 1 mode gre dev eth0
wouldn't be ever matched if it was created before explicit tunnel like above.
All this stuff happened because while looking for a wildcard tunnel we didn't
check that matched tunnel is a wildcard one. Fixed.
Signed-off-by: Dmitry Popov <ixaphire@qrator.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is otherwise a risk of a possible null pointer dereference.
Was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Since commit 37e22164a8 ("tipc: rename and
move message reassembly function") reassembly of long broadcast messages
has been broken. This is because we test for a non-NULL return value
of the *buf parameter as criteria for succesful reassembly. However, this
parameter is left defined even after reception of the first fragment,
when reassebly is still incomplete. This leads to a kernel crash as soon
as a the first fragment of a long broadcast message is received.
We fix this with this commit, by implementing a stricter behavior of the
function and its return values.
This commit should be applied to both net and net-next.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the IEEE 802.15.4 subsystem maintainer to Alexander Aring.
We discussed this change before via e-mail and I collected the acks from the
current maintainers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Alexander Smirnov <alex.bluesman.sminov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Vrabel says:
====================
xen-netfront: multi-queue related locking fixes
Two fixes to the per-queue locking bugs in xen-netfront that were
introduced in 3.16-rc1 with the multi-queue support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In xennet_disconnect_backend(), netif_carrier_off() was called once
per queue when it needs to only be called once.
The queue locking around the netif_carrier_off() call looked very
odd. I think they were supposed to synchronize any NAPI instances with
the expectation that no further NAPI instances would be scheduled
because of the carrier being off (see the check in
xennet_rx_interrupt()). But I can't easily tell if this works
correctly.
Instead, add a napi_synchronize() call after disabling the interrupts.
This is obviously correct as with no Rx interrupts, no further NAPI
instances will be scheduled.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nesting of the per-queue rx_lock and tx_lock in xennet_connect()
is confusing to both humans and lockdep. The locking is safe because
this is the only place where the locks are nested in this way but
lockdep still warns.
Instead of adding the missing lockdep annotations, refactor the
locking to avoid the confusing nesting. This is still safe, because
the xenbus connection state changes are all serialized by the xenwatch
thread.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The undo code assumes that, upon entering loss recovery, TCP
1) always retransmit something
2) the retransmission never fails locally (e.g., qdisc drop)
so undo_marker is set in tcp_enter_recovery() and undo_retrans is
incremented only when tcp_retransmit_skb() is successful.
When the assumption is broken because TCP's cwnd is too small to
retransmit or the retransmit fails locally. The next (DUP)ACK
would incorrectly revert the cwnd and the congestion state in
tcp_try_undo_dsack() or tcp_may_undo(). Subsequent (DUP)ACKs
may enter the recovery state. The sender repeatedly enter and
(incorrectly) exit recovery states if the retransmits continue to
fail locally while receiving (DUP)ACKs.
The fix is to initialize undo_retrans to -1 and start counting on
the first retransmission. Always increment undo_retrans even if the
retransmissions fail locally because they couldn't cause DSACKs to
undo the cwnd reduction.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The add_vxlan_port ndo driver code was wrongly testing whether HW vxlan offloads
are supported by the device instead of checking if they are currently enabled.
This causes the driver to configure the HW parser to conduct matching for vxlan
packets but since no steering rules were set, vxlan packets are dropped on RX.
Fix that by doing the right test, as done in the del_vxlan_port ndo handler.
Fixes: 1b136de ('net/mlx4: Implement vxlan ndo calls')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem was triggered by these steps:
1) create socket, bind and then setsockopt for add mc group.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("192.168.1.2");
setsockopt(sockfd, IPPROTO_IP, IP_ADD_MEMBERSHIP, &mreq, sizeof(mreq));
2) drop the mc group for this socket.
mreq.imr_multiaddr.s_addr = inet_addr("255.0.0.37");
mreq.imr_interface.s_addr = inet_addr("0.0.0.0");
setsockopt(sockfd, IPPROTO_IP, IP_DROP_MEMBERSHIP, &mreq, sizeof(mreq));
3) and then drop the socket, I found the mc group was still used by the dev:
netstat -g
Interface RefCnt Group
--------------- ------ ---------------------
eth2 1 255.0.0.37
Normally even though the IP_DROP_MEMBERSHIP return error, the mc group still need
to be released for the netdev when drop the socket, but this process was broken when
route default is NULL, the reason is that:
The ip_mc_leave_group() will choose the in_dev by the imr_interface.s_addr, if input addr
is NULL, the default route dev will be chosen, then the ifindex is got from the dev,
then polling the inet->mc_list and return -ENODEV, but if the default route dev is NULL,
the in_dev and ifIndex is both NULL, when polling the inet->mc_list, the mc group will be
released from the mc_list, but the dev didn't dec the refcnt for this mc group, so
when dropping the socket, the mc_list is NULL and the dev still keep this group.
v1->v2: According Hideaki's suggestion, we should align with IPv6 (RFC3493) and BSDs,
so I add the checking for the in_dev before polling the mc_list, make sure when
we remove the mc group, dec the refcnt to the real dev which was using the mc address.
The problem would never happened again.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bug was introduced in NETDEV_CHANGE notifier sequence causing the
arp table to be sometimes spuriously cleared (including manual arp
entries marked permanent), upon network link carrier changes.
The changed argument for the notifier was applied only to a single
caller of NETDEV_CHANGE, missing among others netdev_state_change().
So upon net_carrier events induced by the network, which are
triggering a call to netdev_state_change(), arp_netdev_event() would
decide whether to clear or not arp cache based on random/junk stack
values (a kind of read buffer overflow).
Fixes: be9efd3653 ("net: pass changed flags along with NETDEV_CHANGE event")
Fixes: 6c8b4e3ff8 ("arp: flush arp cache on IFF_NOARP change")
Signed-off-by: Loic Prylli <loicp@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0acf167687.
Breaks the build due to missing reference to phy_resume in
the resulting dwmac-socfpga.o object.
Signed-off-by: David S. Miller <davem@davemloft.net>
deal with a compile warning: comparison between
'enum qe_fltr_largest_external_tbl_lookup_key_size'
and 'enum qe_fltr_tbl_lookup_key_size'
the code:
"if (ug_info->largestexternallookupkeysize ==
QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES)"
is warned because different enum, so modify it.
"enum qe_fltr_largest_external_tbl_lookup_key_size
largestexternallookupkeysize;
enum qe_fltr_tbl_lookup_key_size {
QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES
= 0x3f, /* LookupKey parsed by the Generate LookupKey
CMD is truncated to 8 bytes */
QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES
= 0x5f, /* LookupKey parsed by the Generate LookupKey
CMD is truncated to 16 bytes */
};
/* QE FLTR extended filtering Largest External Table Lookup Key Size */
enum qe_fltr_largest_external_tbl_lookup_key_size {
QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_NONE
= 0x0,/* not used */
QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_8_BYTES
= QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES, /* 8 bytes */
QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_16_BYTES
= QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES, /* 16 bytes */
};"
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Open vSwitch
A set of fixes for net.
First bug is related flow-table management. Second one is in sample
action. Third is related flow stats and last one add gre-err handler for ovs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In process_backlog the input_pkt_queue is only checked once for new
packets and quota is artificially reduced to reflect precisely the
number of packets on the input_pkt_queue so that the loop exits
appropriately.
This patches changes the behavior to be more straightforward and
less convoluted. Packets are processed until either the quota
is met or there are no more packets to process.
This patch seems to provide a small, but noticeable performance
improvement. The performance improvement is a result of staying
in the process_backlog loop longer which can reduce number of IPI's.
Performance data using super_netperf TCP_RR with 200 flows:
Before fix:
88.06% CPU utilization
125/190/309 90/95/99% latencies
1.46808e+06 tps
1145382 intrs.sec.
With fix:
87.73% CPU utilization
122/183/296 90/95/99% latencies
1.4921e+06 tps
1021674.30 intrs./sec.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some older router implementations still send Fragmentation Needed
errors with the Next-Hop MTU field set to zero. This is explicitly
described as an eventuality that hosts must deal with by the
standard (RFC 1191) since older standards specified that those
bits must be zero.
Linux had a generic (for all of IPv4) implementation of the algorithm
described in the RFC for searching a list of MTU plateaus for a good
value. Commit 46517008e1 ("ipv4: Kill ip_rt_frag_needed().")
removed this as part of the changes to remove the routing cache.
Subsequently any Fragmentation Needed packet with a zero Next-Hop
MTU has been discarded without being passed to the per-protocol
handlers or notifying userspace for raw sockets.
When there is a router which does not implement RFC 1191 on an
MTU limited path then this results in stalled connections since
large packets are discarded and the local protocols are not
notified so they never attempt to lower the pMTU.
One example I have seen is an OpenBSD router terminating IPSec
tunnels. It's worth pointing out that this case is distinct from
the BSD 4.2 bug which incorrectly calculated the Next-Hop MTU
since the commit in question dismissed that as a valid concern.
All of the per-protocols handlers implement the simple approach from
RFC 1191 of immediately falling back to the minimum value. Although
this is sub-optimal it is vastly preferable to connections hanging
indefinitely.
Remove the Next-Hop MTU != 0 check and allow such packets
to follow the normal path.
Fixes: 46517008e1 ("ipv4: Kill ip_rt_frag_needed().")
Signed-off-by: Edward Allcutt <edward.allcutt@openmarket.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vince Bridgers says:
====================
net: stmmac: Correct socfpga init/exit and
This patch series adds platform specific init/exit code so that socfpga
suspend/resume works as expected, and corrects a minor issue detected by
cppcheck.
V2: Address review comments by adding a line break at end of function and
structure declaration. Add another trivial cppcheck patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a case where a local variable was being assigned a value,
but not used. There seems to be no reason to read this register before
assigning a new value, so addressing thie issue.
cppcheck --force --enable=all --inline-suppr . shows ...
Variable 'value' is reassigned a value before the old one has been used.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a duplicate if/then/else case where a receive descriptor
was being processed. This patch corrects that issue.
cppcheck --force --enable=all --inline-suppr .
...
Checking enh_desc.c...
[enh_desc.c:148] -> [enh_desc.c:144]: (style) Found duplicate if expressions.
...
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max_dsize attribute in ctl_table for lowpan_frags_ns_ctl_table is
configured with integer accessing methods. This patch change the
max_dsize attribute to int to avoid a possible buffer overflow.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai says:
====================
Mellanox EN driver fixes 2014-06-23
Below are some fixes to patches submitted to 3.16.
First patch is according to discussions with Ben [1] and Thomas [2] - to do not
use affinity notifier, since it breaks RFS. Instead detect changes in IRQ
affinity map, by checking if current CPU is set in affinity map on NAPI poll.
The two other patches fix some bugs introduced in commit [3].
Patches were applied and tested over commit dba6311: ('powerpc: bpf: Fix the
broken LD_VLAN_TAG_PRESENT test')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to remove affinity hint at mlx4_en_deactivate_cq() and not at
mlx4_en_destroy_cq() - since affinity_mask might be free'd while still
being used by procfs.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device is non numa aware (numa_node == -1), use all online cpu's.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23 ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compilation warnings:
drivers/net/fddi/defxx.c:294: warning: 'dfx_rcv_flush' declared inline after being called
drivers/net/fddi/defxx.c:294: warning: previous declaration of 'dfx_rcv_flush' was here
drivers/net/fddi/defxx.c:2854: warning: 'my_skb_align' defined but not used
triggered when the driver is built with DYNAMIC_BUFFERS undefined. Code
tested to work just fine with these changes and a few DEFPA and DEFTA
boards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX handler of the driver has two paths switched between, depending on
the size of the frame received, as determined by SKBUFF_RX_COPYBREAK.
When a small frame is received, a new skb allocated has data space large
enough to hold the incoming frame only, and data is copied there from the
original skb whose buffer is returned to the DMA RX ring; in that case
`rx_in_place' is 0. When a large frame is received, a new skb allocated
has data space large enough to hold the largest frame possible, including
the overhead for alignment, the receive status and padding, over 4.5kiB
overall, and its buffer is placed on the DMA RX ring while the original
buffer is passed up to the network stack avoiding the need to copy data;
in that case `rx_in_place' is 1.
However the latter scenario is only possible when dynamic buffers are
used, as determined by DYNAMIC_BUFFERS, because otherwise the buffers used
for the DMA RX ring are fixed at the time the interface is brought up.
That leads to an observation that the preprocessor conditional around the
`rx_in_place' check is inverted, the check only really matters when
dynamic buffers are in use. It has gone unnoticed for many years since
support for using dynamic buffers on the DMA RX ring was introduced in
2.1.40 -- because the only problem that results is in the case where
`rx_in_place' is 1 frame data received is unnecessarily copied to the
newly-allocated buffer, before the buffer placed on the the DMA receive RX
and its contents ignored. Therefore the only symptom is some performance
loss.
Rather than flipping the condition though I decided to discard the
conditional altogether -- in the case of static buffers `rx_in_place' is
always 0 so GCC will optimise the C conditional away instead.
Tested on a few DEFPA and DEFTA boards successfully using both small and
large frames, both with DYNAMIC_BUFFERS defined and with the macro
undefined.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When in repair-mode and TCP_RECV_QUEUE is set, we end up calling
tcp_push with mss_now being 0. If data is in the send-queue and
tcp_set_skb_tso_segs gets called, we crash because it will divide by
mss_now:
[ 347.151939] divide error: 0000 [#1] SMP
[ 347.152907] Modules linked in:
[ 347.152907] CPU: 1 PID: 1123 Comm: packetdrill Not tainted 3.16.0-rc2 #4
[ 347.152907] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 347.152907] task: f5b88540 ti: f3c82000 task.ti: f3c82000
[ 347.152907] EIP: 0060:[<c1601359>] EFLAGS: 00210246 CPU: 1
[ 347.152907] EIP is at tcp_set_skb_tso_segs+0x49/0xa0
[ 347.152907] EAX: 00000b67 EBX: f5acd080 ECX: 00000000 EDX: 00000000
[ 347.152907] ESI: f5a28f40 EDI: f3c88f00 EBP: f3c83d10 ESP: f3c83d00
[ 347.152907] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 347.152907] CR0: 80050033 CR2: 083158b0 CR3: 35146000 CR4: 000006b0
[ 347.152907] Stack:
[ 347.152907] c167f9d9 f5acd080 000005b4 00000002 f3c83d20 c16013e6 f3c88f00 f5acd080
[ 347.152907] f3c83da0 c1603b5a f3c83d38 c10a0188 00000000 00000000 f3c83d84 c10acc85
[ 347.152907] c1ad5ec0 00000000 00000000 c1ad679c 010003e0 00000000 00000000 f3c88fc8
[ 347.152907] Call Trace:
[ 347.152907] [<c167f9d9>] ? apic_timer_interrupt+0x2d/0x34
[ 347.152907] [<c16013e6>] tcp_init_tso_segs+0x36/0x50
[ 347.152907] [<c1603b5a>] tcp_write_xmit+0x7a/0xbf0
[ 347.152907] [<c10a0188>] ? up+0x28/0x40
[ 347.152907] [<c10acc85>] ? console_unlock+0x295/0x480
[ 347.152907] [<c10ad24f>] ? vprintk_emit+0x1ef/0x4b0
[ 347.152907] [<c1605716>] __tcp_push_pending_frames+0x36/0xd0
[ 347.152907] [<c15f4860>] tcp_push+0xf0/0x120
[ 347.152907] [<c15f7641>] tcp_sendmsg+0xf1/0xbf0
[ 347.152907] [<c116d920>] ? kmem_cache_free+0xf0/0x120
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c106a682>] ? __sigqueue_free+0x32/0x40
[ 347.152907] [<c114f0f0>] ? do_wp_page+0x3e0/0x850
[ 347.152907] [<c161c36a>] inet_sendmsg+0x4a/0xb0
[ 347.152907] [<c1150269>] ? handle_mm_fault+0x709/0xfb0
[ 347.152907] [<c15a006b>] sock_aio_write+0xbb/0xd0
[ 347.152907] [<c1180b79>] do_sync_write+0x69/0xa0
[ 347.152907] [<c1181023>] vfs_write+0x123/0x160
[ 347.152907] [<c1181d55>] SyS_write+0x55/0xb0
[ 347.152907] [<c167f0d8>] sysenter_do_call+0x12/0x28
This can easily be reproduced with the following packetdrill-script (the
"magic" with netem, sk_pacing and limit_output_bytes is done to prevent
the kernel from pushing all segments, because hitting the limit without
doing this is not so easy with packetdrill):
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
+0 < S 0:0(0) win 32792 <mss 1460>
+0 > S. 0:0(0) ack 1 <mss 1460>
+0.1 < . 1:1(0) ack 1 win 65000
+0 accept(3, ..., ...) = 4
// This forces that not all segments of the snd-queue will be pushed
+0 `tc qdisc add dev tun0 root netem delay 10ms`
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=2`
+0 setsockopt(4, SOL_SOCKET, 47, [2], 4) = 0
+0 write(4,...,10000) = 10000
+0 write(4,...,10000) = 10000
// Set tcp-repair stuff, particularly TCP_RECV_QUEUE
+0 setsockopt(4, SOL_TCP, 19, [1], 4) = 0
+0 setsockopt(4, SOL_TCP, 20, [1], 4) = 0
// This now will make the write push the remaining segments
+0 setsockopt(4, SOL_SOCKET, 47, [20000], 4) = 0
+0 `sysctl -w net.ipv4.tcp_limit_output_bytes=130000`
// Now we will crash
+0 write(4,...,1000) = 1000
This happens since ec34232575 (tcp: fix retransmission in repair
mode). Prior to that, the call to tcp_push was prevented by a check for
tp->repair.
The patch fixes it, by adding the new goto-label out_nopush. When exiting
tcp_sendmsg and a push is not required, which is the case for tp->repair,
we go to this label.
When repairing and calling send() with TCP_RECV_QUEUE, the data is
actually put in the receive-queue. So, no push is required because no
data has been added to the send-queue.
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Pavel Emelyanov <xemul@parallels.com>
Fixes: ec34232575 (tcp: fix retransmission in repair mode)
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Andrew Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_dst_cache has __rcu annotation, so we need a cast to avoid
following sparse error :
include/net/sock.h:1774:19: warning: incorrect type in initializer (different address spaces)
include/net/sock.h:1774:19: expected struct dst_entry [noderef] <asn:4>*__ret
include/net/sock.h:1774:19: got struct dst_entry *dst
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 7f50236153 ("ipv4: irq safe sk_dst_[re]set() and ipv4_sk_update_pmtu() fix")
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-06-27
Please pull the following batch of fixes for the 3.16 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Eliad for a time calculation, a fix from Max for
head/tailroom when sending authentication packets, a revert that Felix
requested since the patch in question broke regulatory and a fix from
myself for an issue with a new command that we advertised in the wrong
place."
For the bluetooth bits, Gustavo says:
"A few fixes for 3.16. This pull request contains a NULL dereference fix,
and some security/pairing fixes."
For the iwlwifi bits, Emmanuel says:
"I have here a fix from Eliad for scheduled scan: it fixes a firmware
assertion. Arik reverts a patch I made that didn't take into account
that 3160 doesn't have UAPSD and hence, we can't assume that all
newer firmwares support the feature. Here too, the visible effect
is a firmware assertion. Along with that, we have a few fixes and
additions to the device list."
For the ath10k bits, Kalle says:
"Bartosz fixed an issue where we were not able to create 8 vdevs when
using DFS. Michal removed a false warning which was just confusing
people."
On top of that...
Arend van Spriel fixes a 'divide by zero' regression in brcmfmac.
Amitkumar Karwar corrects a transmit timeout in mwifiex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware will provide this information as soon as we will start
processing incoming packets, so there is no need to set the RX buffer
length during buffer allocation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use the PHY library which will determine the link state for us, make
sure we start with a carrier off until libphy has completed the link
training.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as register_netdev() is called, the network device notifiers are
running which means that other parts of the kernel, or user-space
programs can call the network device ndo_open() callback and use the
interface.
Disable the Ethernet device clock before we register the network device
such that we do not create the following situation:
CPU0 CPU1
register_netdev()
bcmgenet_open()
clk_prepare_enable()
clk_disable_unprepare()
and leave the hardware block gated off, while we think it should be
gated on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we do not limit the number of packets the TX completion
function bcm_sysport_tx_reclaim() is allowed to reclaim, we were still
using its return value as-is. This means that we could hit the WARN() in
net/core/dev.c where work_done >= budget.
Make sure we do exit the NAPI context when the TX ring is empty, and
pretend there was no work to do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UniMAC CMD_SW_RESET bit is not a self-clearing bit, so we need to
assert it, wait a bit and clear it manually. As a result, umac_reset()
is updated not to return any value. The previous version of the code
simply wrote 0 to the CMD register, which would make the busy-waiting
loop exit immediately, having zero effect.
By writing 0 to the CMD register, we were clearing all bits in the CMD
register, and not using the hardware reset default values which are
set on purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT Ethernet MAC supports multicast just fine, it just lacks
any sort of Unicast/Broadcast/Multicasting filtering at the Ethernet MAC
level since that is handled by the front end Ethernet switch, but that
is properly handled by bcm_sysport_set_rx_mode().
Some user-space applications might be relying on the presence of this
flag to prevent using multicast sockets, this also prevents that
interface from joining the IPv6 all-router mcast group.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))
BUG: unable to handle kernel paging request at ffffeba400000000
IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132cc0 ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two different ways to handle changes to sk->sk_dst
First way (used by TCP) assumes socket lock is owned by caller, and use
no extra lock : __sk_dst_set() & __sk_dst_reset()
Another way (used by UDP) uses sk_dst_lock because socket lock is not
always taken. Note that sk_dst_lock is not softirq safe.
These ways are not inter changeable for a given socket type.
ipv4_sk_update_pmtu(), added in linux-3.8, added a race, as it used
the socket lock as synchronization, but users might be UDP sockets.
Instead of converting sk_dst_lock to a softirq safe version, use xchg()
as we did for sk_rx_dst in commit e47eb5dfb2 ("udp: ipv4: do not use
sk_dst_lock from softirq context")
In a follow up patch, we probably can remove sk_dst_lock, as it is
only used in IPv6.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Fixes: 9cb3a50c5f ("ipv4: Invalidate the socket cached route on pmtu events if possible")
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the race condition in userspace, there is chance that two
overlapping megaflows could be installed in datapath. And this
causes userspace unable to delete the less inclusive megaflow flow
even after it timeout, since the flow_del logic will stop at the
first match of masked flow.
This commit fixes the bug by making the kernel flow_del and flow_get
logic check all masks in that case.
Introduced by 03f0d916a (openvswitch: Mega flow implementation).
Signed-off-by: Alex Wang <alexw@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
