This introduces some much overdue chainsawing of the fixed PMB support.
fixed PMB was introduced initially to work around the fact that dynamic
PMB mode was relatively broken, though they were never intended to
converge. The main areas where there are differences are whether the
system is booted in 29-bit mode or 32-bit mode, and whether legacy
mappings are to be preserved. Any system booting in true 32-bit mode will
not care about legacy mappings, so these are roughly decoupled.
Regardless of the entry point, PMB and 32BIT are directly related as far
as the kernel is concerned, so we also switch back to having one select
the other.
With legacy mappings iterated through and applied in the initialization
path it's now possible to finally merge the two implementations and
permit dynamic remapping overtop of remaining entries regardless of
whether boot mappings are crafted by hand or inherited from the boot
loader.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The mass produced cuts use an updated PVR value, add them to the list.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes vmlinux.bin generation an explicit make target, as opposed to
just a dependency for some of the other targets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The legacy P2 area may not always be mapped (for example when using
PMB). So perform an icbi on an address that we know will always be
mapped.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 xstate changes and implements a task_xstate slab
cache that is dynamically sized to match one of hard FP/soft FP/FPU-less.
This also tidies up and consolidates some of the SH-2A/SH-4 FPU
fragmentation. Now fpu state restorers are commonly defined, with the
init_fpu()/fpu_init() mess reworked to follow the x86 convention.
The fpu_init() register initialization has been replaced by xstate setup
followed by writing out to hardware via the standard restore path.
As init_fpu() now performs a slab allocation a secondary lighterweight
restorer is also introduced for the context switch.
In the future the DSP state will be rolled in here, too.
More work remains for math emulation and the SH-5 FPU, which presently
uses its own special (UP-only) interfaces.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this has a BUG_ON() for failure cases, as powerpc does. Switch
this over to a SLAB_PANIC instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the thread_info allocators are special cased, depending on
THREAD_SHIFT < PAGE_SHIFT. This provides a sensible definition for them
regardless of configuration, in preparation for extended CPU state.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
start_thread() will become a bit heavier with the xstate freeing to be
added in, so move it out-of-line in preparation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some VBR sanity checks in the sh_bios code to ensure that the
BIOS VBR is in range before blindly trapping in to it. This permits
boards with varying boot loader configurations to always leave support
for sh-bios enabled and it will just be disabled at run-time if not
found.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the unaligned access counters and userspace bits in to
their own generic interface, which will allow them to be wired up on sh64
too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the sh-sci earlyprintk is taken care of by the sh-sci driver
directly, there's no longer any reason for having a split-out
early_printk framework. sh_bios is the only other thing that uses it, so
we just migrate the leftovers in to there. As it's possible to have
multiple early_param()'s for the same string, there's not much point in
having this split out anymore anyways, particularly since the sh_bios
dependencies are still special-cased within sh-sci itself.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was conditionalized on CONFIG_EARLY_PRINTK, which has subsequently
gone away. Now that the serial driver always supports the early console,
make sure we always establish the mapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the VBR handling out of the main trap handling code and in to
the sh-bios helper code. A couple of accessors are added in order to
permit other kernel code to get at the VBR value for state save/restore
paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As SH has a very sparse IRQ map by default, all new CPUs and boards
benefit from using sparseirq by default. Despite this, there are still a
few stragglers (mostly due to using a fixed IRQ range for their FPGA
IRQ mappings), and these still need to be converted over one by one. As
these are now in the minority, and we do not want to encourage this sort
of brain-damage in newer board ports, we force sparseirq on.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This gets rid of the arbitrary set of vectors used by the SE7722 FPGA
interrupt controller and switches over to a completely dynamic set.
No assumptions regarding a contiguous range are made, and the platform
resources themselves need to be filled in lazily.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Revert commit 2fbd07a5f5, as this commit
breaks an IBM platform with quad-core Xeon cpu's.
According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).
Revert this for now because of the IBM platform breakage.
Another version will be re-submitted after the complete analysis.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The list macros use LIST_POISON1 and LIST_POISON2 as undereferencable
pointers in order to trap erronous use of freed list_heads. Unfortunately
userspace can arrange for those pointers to actually be dereferencable,
potentially turning an oops to an expolit.
To avoid this allow architectures (currently x86_64 only) to override
the default values for these pointers with truly-undereferencable values.
This is easy on x86_64 as the virtual address space is large and contains
areas that cannot be mapped.
Other 64-bit architectures will likely find similar unmapped ranges.
[ingo: switch to 0xdead000000000000 as the unmapped area]
[ingo: add comments, cleanup]
[jaswinder: eliminate sparse warnings]
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the defconfig for the ASB2303 platform.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Access to the ASB2305's PCnet32 NIC doesn't work correctly because when
the NIC attempts to update the ring buffer flags by DMA, the change to RAM
crops up about 17uS after the interrupt line is asserted. This is almost
certainly due to a bug in the PCI bridge FPGA on that board.
We can get around this by making dma_alloc_coherent() put the ring buffer
in the SRAM attached to the PCI bridge rather than in the SDRAM.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert PCI root bus resources for the MN10300-based ASB2305 development
kit motherboard. This is required because the CPU's window onto the PCI
bus address space is considerably smaller than the CPU's full address
space and non-PCI devices lie outside of the PCI window that we might want
to access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
We also add a reservation for the PCI SRAM region.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks PCI_NUM_RESOURCES (11), not 6, resources
- skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
- skips ROM resources unless IORESOURCE_ROM_ENABLE is set
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use KERN_ERR not KERN_ERROR in the ASB2305 platform code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/cpu never existed for mn10300; the files they are looking for are in
asm.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wire up missing new system calls for MN10300.
Signed-off-by: David Howells <dhowelsl@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 4.2.1 for MN10300 is more agressive than the older gcc in
reordering/moving other insns between an insn that sets flags and an insn
that uses those flags. This leads to trouble with asm statements which
are missing an explicit "cc" clobber. This patch adds the explicit "cc"
clobber to asm statements which do indeed clobber the condition flags.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gcc-4.2.1 based toolchain for MN10300 adds some new note sections
which need to be stripped from the binary image. This patch takes care of
that.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a signal stack handling problem in the MN10300 arch. When new
threads are cloned with CLONE_VM, they don't inherit the alternate signal
stack. They do share the signal flags, though. When deciding whether to
use an alternate stack, the arch code needs to check to make sure the task
struct contains a valid alternate stack. This patch fixes the MN10300
arch by using the sas_ss_flags() test provided by sched.h rather than the
on_sig_stack() test which is insufficient by itself.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- changes to ach/arch/boot/Makefile to make it easier to add new
compression types
- new piggy.lzo.S necessary for lzo compression
- changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
gzip, depending on the config
- Kconfig support
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
JFFS2 uses lesser compression ratio and inflate always ends up in "copy
direct from output" case.
This patch tries to optimize the direct copy procedure. Uses
get_unaligned() but only in one place.
The copy loop just above this one can also use this optimization, but I
havn't done so as I have not tested if it is a win there too.
On my MPC8321 this is about 17% faster on my JFFS2 root FS than the
original.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dynamically allocate the CPUFreq frequency table on OMAP2xxx chips.
This fixes some compilation problems, since the kernel may not know
what chip it is running on until boot-time. This also reduces the size
of the CPUFreq frequency table.
Problem originally reported by Felipe Balbi <felipe.balbi@nokia.com>.
Thanks also for comments on the patch from Felipe and Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Revise some of the comments in the OMAP2xxx OPP data for clarity.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
if we enable CPUFREQ we can't build omap2 for two reasons,
one of them is fixed by the patch below.
It's failing because the __must_be_array() check in
ARRAY_SIZE() is failing and printing the following message:
arch/arm/mach-omap2/clock2xxx.c:453: error: negative width in bit-field '<anonymous>'
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
[paul@pwsan.com: commit message updated; changed rate variable name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 52650505fb added an __initdata
decoration to the structure containing the clk_enable and clk_disable
functions. Once init data was freed, these pointers went to null, and
the next enable or disable call caused the kernel to crash. This
change removes this decoration.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: patch manually split and commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This change adds in some missing clocks that were needed as a result
of 526505... (OMAP1 clock: convert mach-omap1/clock.h to
mach-omap1/clock_data.c). Prior to this, it was just assumed that
these clocks existed for all devices, and it was used directly instead
of calling it out with a clock_get call or similar. So, not having
the CK_7XX meant these clocks weren't being used anymore for omap 7xx
devices, which broke things badly.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The only symbols that should be exported are symbols that are to be
called from loadable kernel modules, e.g., device drivers. In the
context of plat-omap/clock.c, these should only be the Linux clock
interface symbols as defined by include/linux/clk.h. Core code
doesn't need these symbols to be exported. Also, clean up an old
comment while here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add necessary definitions to clock framework to allow changing
dpll4_m5_ck rate. This is used by the camera code.
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The correct parent of the McBSP 2, 3, and 4 functional clocks is
PER_96M_FCLK, not CORE_96M_FCLK. Fix this in the OMAP clock tree.
Reported by Nicole Chalhoub <n-chalhoub@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>
UART1 & 2 were missing clockdomains resulting in broken omap_hwmod
init for these devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 10db25fea4 causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):
[ 0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space
Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP2/3 some of the clock-domains which did not have control
facility were being falsely written to and read using the CM_CLKSTCTRL
register though it did not exist for them. One check is added to remove
this flaw.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
