Exynos USB2 PHY has separate power supply, which is usually provided by
VBUS regulator. This patch adds support for it. VBUS regulator is
optional, to keep compatibility with boards, which have VBUS provided
from some always-on power source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=97xz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 4.3
*) Add new NXP USB OTG PHY driver
*) Add vbus/id detection, extcon support and fixes in phy-sun4i-usb
driver
*) Add support to use phy-sun4i-usb driver for sun8i-a23 and sun8i-a33
SoCs
*) Other trivial code cleanups, dropping .owner assignment and constify
phy_ops
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SATA_PLL_SOFT_RESET bit of CTRL_CORE_SMA_SW_0 must be toggled
between a SATA DPLL unlock and re-lock to prevent SATA lockup.
Introduce a new DT parameter 'syscon-pllreset' to provide the syscon
regmap access to this register which sits in the control module.
If the register is not provided we fallback to the old behaviour
i.e. SATA DPLL refclk will not be disabled and we prevent SoC low
power states.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
On some boards there is no vbus_det gpio pin, instead vbus-detection for
otg can be done via the pmic.
This commit adds support for monitoring vbus_det via the power_supply
exported by the pmic, enabling support for otg on these boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phys on the sun8i-a33 SoC are mostly the same as sun8i-a23 but for
some reason (hw bug?) the phyctl register was moved to a different address
and is not initialized to 0 on reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb-phys on the sun8i-a23 SoC have the same setup wrt clocks as on the
sun6i-a31 SoC, but there are only 2 instead of 3 like on the sun5i-a13 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The usb0 phy is connected to an OTG controller, and as such needs some special
handling:
1) It allows explicit control over the pullups, enable these on phy_init and
disable them on phy_exit.
2) It has bits to signal id and vbus detect to the musb-core, add support for
for monitoring id and vbus detect gpio-s for use in dual role mode, and set
these bits to the correct values for operating in host only mode when no
gpios are specified in the devicetree.
While updating the devicetree binding documentation also add documentation
for the sofar undocumented usage of regulators for vbus for all 3 phys.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add binding documentation for NXP LPC18xx/43xx USB OTG PHY. This
PHY can found on NXP LPC18xx and LPC43xx devices with USB support.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull MIPS updates from Ralf Baechle:
- Improvements to the tlb_dump code
- KVM fixes
- Add support for appended DTB
- Minor improvements to the R12000 support
- Minor improvements to the R12000 support
- Various platform improvments for BCM47xx
- The usual pile of minor cleanups
- A number of BPF fixes and improvments
- Some improvments to the support for R3000 and DECstations
- Some improvments to the ATH79 platform support
- A major patchset for the JZ4740 SOC adding support for the CI20 platform
- Add support for the Pistachio SOC
- Minor BMIPS/BCM63xx platform support improvments.
- Avoid "SYNC 0" as memory barrier when unlocking spinlocks
- Add support for the XWR-1750 board.
- Paul's __cpuinit/__cpuinitdata cleanups.
- New Malta CPU board support large memory so enable ZONE_DMA32.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (131 commits)
MIPS: spinlock: Adjust arch_spin_lock back-off time
MIPS: asmmacro: Ensure 64-bit FP registers are used with MSA
MIPS: BCM47xx: Simplify handling SPROM revisions
MIPS: Cobalt Don't use module_init in non-modular MTD registration.
MIPS: BCM47xx: Move NVRAM driver to the drivers/firmware/
MIPS: use for_each_sg()
MIPS: BCM47xx: Don't select BCMA_HOST_PCI
MIPS: BCM47xx: Add helper variable for storing NVRAM length
MIPS: IRQ/IP27: Move IRQ allocation API to platform code.
MIPS: Replace smp_mb with release barrier function in unlocks.
MIPS: i8259: DT support
MIPS: Malta: Basic DT plumbing
MIPS: include errno.h for ENODEV in mips-cm.h
MIPS: Define GCR_GIC_STATUS register fields
MIPS: BPF: Introduce BPF ASM helpers
MIPS: BPF: Use BPF register names to describe the ABI
MIPS: BPF: Move register definition to the BPF header
MIPS: net: BPF: Replace RSIZE with SZREG
MIPS: BPF: Free up some callee-saved registers
MIPS: Xtalk: Update xwidget.h with known Xtalk device numbers
...
Add a binding document for the USB2.0 PHY found on the IMG Pistachio SoC.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Damien Horsley <Damien.Horsley@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/9727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a compatible string to support for R-Car E2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
devicetree changes queued up for v4.1. Here are the highlights:
- Lots of unittest cleanup from Frank Rowand
- Bugfixes and updates to the of_graph code
- Tighten up of_get_mac_address() code
- Documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u6Zy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Here are the devicetree changes queued up for v4.1. Nothing really
exciting here. Rob has another few commits for big-endian attached
UARTs, but those will be sent in a separate merge request since they
haven't been as thoroughly tested as this batch.
Here are the highlights:
- lots of unittest cleanup from Frank Rowand
- bugfixes and updates to the of_graph code
- tighten up of_get_mac_address() code
- documentation updates"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Fix of_platform_depopulate test case
of/unittest: early return from test skips tests
of/unittest: breadcrumbs to reduce pain of future maintainers
of/unittest: reduce checkpatch noise - line after declarations
of/unittest: typo in error string
of/unittest: add const where needed
of_net: factor out repetitive code from of_get_mac_address()
drivers/of: Add empty ranges quirk for PA-Semi
of: Allow selection of OF_DYNAMIC and OF_OVERLAY if OF_UNITTEST
of: Empty node & property flag accessors when !OF
of: Explicitly include linux/types.h in of_graph.h
dt-bindings: brcm: rationalize Broadcom documentation naming
of/unittest: replace 'selftest' with 'unittest'
Documentation: rename of_selftest.txt to of_unittest.txt
Documentation: update the of_selftest.txt
dt: OF_UNITTEST make dependency broken
MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
of: Add of_graph_get_port_by_id function
of: Add for_each_endpoint_of_node helper macro
of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint
Now there are generic phy type constants declared in phy.h, migrate over to
using them rather than defining our own. This change has been done as one
atomic commit to be bisectable.
Note: The values of the defines are the same, so there is no ABI breakage
with this patch.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Unlike previous Allwinner SoCs, there is no central PHY control block
on the A80. Also, OTG support is completely split off into a different
controller.
This adds a new driver to support the regular USB PHYs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a minimal driver for dm816x USB. This makes USB work on dm816x
without any other changes needed as it can use the existing musb_dsps
glue layer for the USB controller.
Note that this phy is different from dm814x and am335x.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patchset attempts to standardize the naming of dt-bindings
documents based on the Broadcom vendor prefix of brcm.
Although there are no guidelines currently present for how to name
the dt-bindings document the "vendor,binding.txt" style is in use by
some of the other vendors.
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds driver data to support for Exynos5433 SoC.
The Exynos5433 has one USB3.0 Host and USB3.0 DRD(Dual Role Device).
Exynos5433 is simplar to Eyxnos7 but Exynos5433 have
one more USB3.0 Host controller.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
After the Exynos Power Management Unit (PMU) driver was converted
to the platform device driver in commit 14fc8b93d4
("ARM: EXYNOS: Add platform driver support for Exynos PMU") and
then PMU device nodes added to Exynos4 DTs in commit
7b9613aca4 ("ARM: dts: add PMU syscon node for exynos4")
the mipi video phy driver started failing probing, due to overlapping
memory mapped register region resources.
Now all the Exynos peripheral devices which have registers in the PMU
region are supposed to use the regmap provided by the syscon driver.
So support for regmap is added in this patch, this unfortunately
creates yet another indirection into that supposedly trivial driver.
The additional mutex is required because single register is used by
PHY pairs (they share bit in a register). An improvement here could
be to allow a PHY instance be created with a driver custom mutex,
which would then be common for each PHY pair. This would eliminate
one of 3 mutexes which need to be taken in the phy_power_on/
phy_power_off code path. However, I tried to keep this bug fix patch
possibly simple.
This change is needed to make MIPI DSI displays and MIPI CSI-2
camera sensors working again on Exynos4 boards.
Cc: Pankaj Dubey <pankaj.dubey@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds a binding that describes the Rockchip usb PHYs
found on Rockchip SoCs usb interface.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the phy driver to not use the reg property to access the sysconfig
register offsets.
This is because other phy's (miphy28, miphy365) have a combination of
memory mapped registers and sysconfig control regs, and we shouldn't
be mixing address spaces in the reg property. In addition we would
ideally like the sysconfig offsets to be passed via DT in a uniform way.
This new method will also allow us to support devices which have sysconfig
registers in different banks more easily and it is also analagous to how
keystone and bcm7745 platforms pass there syscon offsets in DT.
This breaks DT compatibility, but this platform is considered WIP, and
is only used by a few developers who are upstreaming support for it.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy28lp phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces like
it does currently for miphy28lp. This change then also aligns us to how other
platforms such as keystone and bcm7445 pass there syscon offsets via DT.
I have updated the miphy28lp phy driver same way as Peter's implementation.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Armada 375 comes with an USB2 host and device controller and an USB3
controller. The USB cluster control register allows to manage common
features of both USB controllers. This commit adds the Device Tree
binding documentation for this piece of hardware.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Describe the binding for the Marvell MVEBU SATA phy. This driver
can be used at least with Kirkwood, Dove and maybe others.
Additionally, update the SATA binding with the properties to link
to the phy nodes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos7 SoC has now separate gate control for 125MHz pipe3 phy
clock, as well as 60MHz utmi phy clock.
Additionally, separate gate control is available for the clock
used for ITP (Isochronous Transfer Packet) generation.
So get the same and control in the phy-exynos5-usbdrd driver.
Suggested-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Document the bindings of the Marvell Berlin USB PHY driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Berlin BG2 SATA PHY is slightly different from currently supported
BG2Q SATA PHY. Document the new compatible for BG2's PHY.
Acked-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to compensate tx impedance (Sata, PCIe)
depending on Soc cuts the kernel is built for.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch to tune on/off the ssc on miphy sata setup.
User can now enable ssc via dt blob, it is useful to reduce
effects of EMI.
Signed-off-by: Giuseppe Condorelli <giuseppe.condorelli@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The MiPHY28lp is a Generic PHY which can serve various SATA or PCIe
or USB3 devices.
Signed-off-by: alexandre torgue <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here's the big USB patchset for 3.18-rc1. Also in here is the PHY tree,
as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full details
in the changelog below.
All have been in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aLYACgkQMUfUDdst+ylBvwCgs9fGRj0RQkLyGhQdEpzdZtTU
ZcwAoMPBImnaA1ZeSl7ZnoO8vC/WE4bR
=tfpj
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
includes miscellaneous cleanup of other PHY drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Efl5
-----END PGP SIGNATURE-----
Merge tag 'phy-for_3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
Adds 3 new PHY drivers stih407, stih41x and rcar gen2 PHY. It also
includes miscellaneous cleanup of other PHY drivers.
Conflicts:
MAINTAINERS
Currently the DP_PHY_ENABLE register is mapped in the driver,
and accessed to control power to the PHY.
With mfd-syscon and regmap interface available at our disposal,
it's wise to use that instead of using a 'reg' property for the
controller and allocating a memory resource for that.
To facilitate this, we have added another compatible string
for Exynso5420 SoC to acquire driver data which contains
different DP-PHY-CONTROL register offset.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds dt documentation bindings for the usb phy found
on STiH415/5 SoC's from STMicroelectronics, which support USB 1.1 and 2.0.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds the dt documentation for the usb picophy found on stih407 SoC family
available from STMicroelectronics.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This PHY, though formally being a part of Renesas USBHS controller, contains the
UGCTRL2 register that controls multiplexing of the USB ports (Renesas calls them
channels) to the different USB controllers: channel 0 can be connected to either
PCI EHCI/OHCI or USBHS controllers, channel 2 can be connected to PCI EHCI/OHCI
or xHCI controllers.
This is a new driver for this USB PHY currently already supported under drivers/
usb/phy/. The reason for writing the new driver was the requirement that the
multiplexing of USB channels to the controller be dynamic, depending on what
USB drivers are loaded, rather than static as provided by the old driver. The
infrastructure provided by drivers/phy/phy-core.c seems to fit that purpose
ideally. The new driver only supports device tree probing for now.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
QCOM USB3.0 core wrapper consist of USB3.0 IP from Synopsys
(SNPS) and HS, SS PHY's control and configuration registers.
It could operate in device mode (SS, HS, FS) and host
mode (SS, HS, FS, LS).
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add binding spec for Qualcomm SoC PHYs, starting with the SATA PHY on
the IPQ806x family of SoCs.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The Berlin SATA PHY drives the PHY related to the SATA interface. Add
the corresponding documentation.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds binding spec for Qualcomm AP8064 SATA PHY.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
phy-supply is a phandle to the regulator that provides power to the
PHY. This regulator is managed during the PHY power on/off sequence
by the phy core driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds support for Exynos3250 SoC to Exynos2USB PHY driver.
Although Exynos3250 has only one device phy interface, the register
layout and all operations that are required to get it enabled are almost
same as on Exynos4x12. The only different is one more register
(REFCLKSEL) which need to be set and lack of MODE SWITCH register.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
