The driver needs to verify there is a payload with a command before
seeing if it should use SGLs to map it.
Fixes: 955b1b5a00 ("nvme-pci: move use_sgl initialization to nvme_init_iod()")
Reported-by: Paul Menzel <pmenzel+linux-nvme@molgen.mpg.de>
Reviewed-by: Paul Menzel <pmenzel+linux-nvme@molgen.mpg.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Calling accept on a TCP socket with a TLS ulp attached results
in two sockets that share the same ulp context.
The ulp context is freed while a socket is destroyed, so
after one of the sockets is released, the second second will
trigger a use after free when it tries to access the ulp context
attached to it.
We restrict the TLS ulp to sockets in ESTABLISHED state
to prevent the scenario above.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Reported-by: syzbot+904e7cd6c5c741609228@syzkaller.appspotmail.com
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r8153 on Dell TB15/16 dock corrupts rx packets.
This change is suggested by Realtek. They guess that the XHCI controller
doesn't have enough buffer, and their guesswork is correct, once the RX
aggregation gets disabled, the issue is gone.
ASMedia is currently working on a real sulotion for this issue.
Dell and ODM confirm the bcdDevice and iSerialNumber is unique for TB16.
Note that TB15 has different bcdDevice and iSerialNumber, which are not
unique values. If you still have TB15, please contact Dell to replace it
with TB16.
BugLink: https://bugs.launchpad.net/bugs/1729674
Cc: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- A rather involved set of memory hardware encryption fixes to
support the early loading of microcode files via the initrd. These
are larger than what we normally take at such a late -rc stage, but
there are two mitigating factors: 1) much of the changes are
limited to the SME code itself 2) being able to early load
microcode has increased importance in the post-Meltdown/Spectre
era.
- An IRQ vector allocator fix
- An Intel RDT driver use-after-free fix
- An APIC driver bug fix/revert to make certain older systems boot
again
- A pkeys ABI fix
- TSC calibration fixes
- A kdump fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/vector: Fix off by one in error path
x86/intel_rdt/cqm: Prevent use after free
x86/mm: Encrypt the initrd earlier for BSP microcode update
x86/mm: Prepare sme_encrypt_kernel() for PAGE aligned encryption
x86/mm: Centralize PMD flags in sme_encrypt_kernel()
x86/mm: Use a struct to reduce parameters for SME PGD mapping
x86/mm: Clean up register saving in the __enc_copy() assembly code
x86/idt: Mark IDT tables __initconst
Revert "x86/apic: Remove init_bsp_APIC()"
x86/mm/pkeys: Fix fill_sig_info_pkey
x86/tsc: Print tsc_khz, when it differs from cpu_khz
x86/tsc: Fix erroneous TSC rate on Skylake Xeon
x86/tsc: Future-proof native_calibrate_tsc()
kdump: Write the correct address of mem_section into vmcoreinfo
Pull scheduler fix from Ingo Molnar:
"A delayacct statistics correctness fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
delayacct: Account blkio completion on the correct task
Pull x86 perf fix from Ingo Molnar:
"An Intel RAPL events fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/rapl: Fix Haswell and Broadwell server RAPL event
tfile->tun could be detached before we close the tun fd,
via tun_detach_all(), so it should not be used to check for
tfile->tx_array.
As Jason suggested, we probably have to clean it up
unconditionally both in __tun_deatch() and tun_detach_all(),
but this requires to check if it is initialized or not.
Currently skb_array_cleanup() doesn't have such a check,
so I check it in the caller and introduce a helper function,
it is a bit ugly but we can always improve it in net-next.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Fixes: 1576d98605 ("tun: switch to use skb array for tx")
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 pti bits and fixes from Thomas Gleixner:
"This last update contains:
- An objtool fix to prevent a segfault with the gold linker by
changing the invocation order. That's not just for gold, it's a
general robustness improvement.
- An improved error message for objtool which spares tearing hairs.
- Make KASAN fail loudly if there is not enough memory instead of
oopsing at some random place later
- RSB fill on context switch to prevent RSB underflow and speculation
through other units.
- Make the retpoline/RSB functionality work reliably for both Intel
and AMD
- Add retpoline to the module version magic so mismatch can be
detected
- A small (non-fix) update for cpufeatures which prevents cpu feature
clashing for the upcoming extra mitigation bits to ease
backporting"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
module: Add retpoline tag to VERMAGIC
x86/cpufeature: Move processor tracing out of scattered features
objtool: Improve error message for bad file argument
objtool: Fix seg fault with gold linker
x86/retpoline: Add LFENCE to the retpoline/RSB filling RSB macros
x86/retpoline: Fill RSB on context switch for affected CPUs
x86/kasan: Panic if there is not enough memory to boot
Pull timer fix from Thomas Gleixner:
"A one-liner fix which prevents deferrable timers becoming stale when
the system does not switch into NOHZ mode"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timers: Unconditionally check deferrable base
As per 90caccdd8c ("bpf: fix bpf_tail_call() x64 JIT"), the index used
for array lookup is defined to be 32-bit wide. Update a misleading
comment that suggests it is 64-bit wide.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When the source and destination register are identical, our JIT does not
generate correct code, which leads to kernel oopses.
Fix this by (a) generating more efficient code, and (b) making use of
the temporary earlier if we will overwrite the address register.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When an eBPF program tail-calls another eBPF program, it enters it after
the prologue to avoid having complex stack manipulations. This can lead
to kernel oopses, and similar.
Resolve this by always using a fixed stack layout, a CPU register frame
pointer, and using this when reloading registers before returning.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The stack layout documentation incorrectly suggests that the BPF JIT
scratch space starts immediately below BPF_FP. This is not correct,
so let's fix the documentation to reflect reality.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Move the stack documentation towards the top of the file, where it's
relevant for things like the register layout.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
As per 2dede2d8e9 ("ARM EABI: stack pointer must be 64-bit aligned
after a CPU exception") the stack should be aligned to a 64-bit boundary
on EABI systems. Ensure that the eBPF JIT appropraitely aligns the
stack.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Avoid the 'bx' instruction on CPUs that have no support for Thumb and
thus do not implement this instruction by moving the generation of this
opcode to a separate function that selects between:
bx reg
and
mov pc, reg
according to the capabilities of the CPU.
Fixes: 39c13c204b ("arm: eBPF JIT compiler")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
It looks like in all cases 'struct vmw_connector_state' is used. But
only in stdu connectors, was atomic_{duplicate,destroy}_state() properly
subclassed. Leading to writes beyond the end of the allocated connector
state block and all sorts of fun memory corruption related crashes.
Fixes: d7721ca711 "drm/vmwgfx: Connector atomic state"
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Clark <rclark@redhat.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Commit 6e032b350c ("powerpc/powernv: Check device-tree for RFI flush
settings") uses u64 in asm/hvcall.h without including linux/types.h
This breaks hvcall.h users that do not include the header themselves.
Fixes: 6e032b350c ("powerpc/powernv: Check device-tree for RFI flush settings")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Expose the state of the RFI flush (enabled/disabled) via debugfs, and
allow it to be enabled/disabled at runtime.
eg: $ cat /sys/kernel/debug/powerpc/rfi_flush
1
$ echo 0 > /sys/kernel/debug/powerpc/rfi_flush
$ cat /sys/kernel/debug/powerpc/rfi_flush
0
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
The recent commit 87590ce6e3 ("sysfs/cpu: Add vulnerability folder")
added a generic folder and set of files for reporting information on
CPU vulnerabilities. One of those was for meltdown:
/sys/devices/system/cpu/vulnerabilities/meltdown
This commit wires up that file for 64-bit Book3S powerpc.
For now we default to "Vulnerable" unless the RFI flush is enabled.
That may not actually be true on all hardware, further patches will
refine the reporting based on the CPU/platform etc. But for now we
default to being pessimists.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Keith reported the following warning:
WARNING: CPU: 28 PID: 1420 at kernel/irq/matrix.c:222 irq_matrix_remove_managed+0x10f/0x120
x86_vector_free_irqs+0xa1/0x180
x86_vector_alloc_irqs+0x1e4/0x3a0
msi_domain_alloc+0x62/0x130
The reason for this is that if the vector allocation fails the error
handling code tries to free the failed vector as well, which causes the
above imbalance warning to trigger.
Adjust the error path to handle this correctly.
Fixes: b5dc8e6c21 ("x86/irq: Use hierarchical irqdomain to manage CPU interrupt vectors")
Reported-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Keith Busch <keith.busch@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801161217300.1823@nanos
intel_rdt_iffline_cpu() -> domain_remove_cpu() frees memory first and then
proceeds accessing it.
BUG: KASAN: use-after-free in find_first_bit+0x1f/0x80
Read of size 8 at addr ffff883ff7c1e780 by task cpuhp/31/195
find_first_bit+0x1f/0x80
has_busy_rmid+0x47/0x70
intel_rdt_offline_cpu+0x4b4/0x510
Freed by task 195:
kfree+0x94/0x1a0
intel_rdt_offline_cpu+0x17d/0x510
Do the teardown first and then free memory.
Fixes: 24247aeeab ("x86/intel_rdt/cqm: Improve limbo list processing")
Reported-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Peter Zilstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: "Roderick W. Smith" <rod.smith@canonical.com>
Cc: 1733662@bugs.launchpad.net
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801161957510.2366@nanos
Add a marker for retpoline to the module VERMAGIC. This catches the case
when a non RETPOLINE compiled module gets loaded into a retpoline kernel,
making it insecure.
It doesn't handle the case when retpoline has been runtime disabled. Even
in this case the match of the retcompile status will be enforced. This
implies that even with retpoline run time disabled all modules loaded need
to be recompiled.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Woodhouse <dwmw@amazon.co.uk>
Cc: rusty@rustcorp.com.au
Cc: arjan.van.de.ven@intel.com
Cc: jeyu@kernel.org
Cc: torvalds@linux-foundation.org
Link: https://lkml.kernel.org/r/20180116205228.4890-1-andi@firstfloor.org
The 4.15 vmwgfx driver shows a warning during boot.
It is caused by a mismatch between the result of vmw_enable_vblank()
and what the drm_atomic_helper expects.
Signed-off by: Woody Suwalski <terraluna977@gmail.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Processor tracing is already enumerated in word 9 (CPUID[7,0].EBX),
so do not duplicate it in the scattered features word.
Besides being more tidy, this will be useful for KVM when it presents
processor tracing to the guests. KVM selects host features that are
supported by both the host kernel (depending on command line options,
CPU errata, or whatever) and KVM. Whenever a full feature word exists,
KVM's code is written in the expectation that the CPUID bit number
matches the X86_FEATURE_* bit number, but this is not the case for
X86_FEATURE_INTEL_PT.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luwei Kang <luwei.kang@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Link: http://lkml.kernel.org/r/1516117345-34561-1-git-send-email-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Oops fix in hfi1 driver
- Use-after-free issue in iser-target
- Use of user supplied array index without proper checking
-----BEGIN PGP SIGNATURE-----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=MHNK
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Doug Ledford:
"We had a few more items creep up over the last week. Given we are in
-rc8, these are obviously limited to bugs that have a big downside and
for which we are certain of the fix.
The first is a straight up oops bug that all you have to do is read
the code to see it's a guaranteed 100% oops bug.
The second is a use-after-free issue. We get away lucky if the queue
we are shutting down is empty, but if it isn't, we can end up oopsing.
We really need to drain the queue before destroying it.
The final one is an issue with bad user input causing us to access our
port array out of bounds. While fixing the array out of bounds issue,
it was noticed that the original code did the same thing twice (the
call to rdma_ah_set_port_num()), so its removal is not balanced by a
readd elsewhere, it was already where it needed to be in addition to
where it didn't need to be.
Summary:
- Oops fix in hfi1 driver
- use-after-free issue in iser-target
- use of user supplied array index without proper checking"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix out-of-bound access while querying AH
IB/hfi1: Prevent a NULL dereference
iser-target: Fix possible use-after-free in connection establishment error
Alexei found that verifier does not reject stores into context
via BPF_ST instead of BPF_STX. And while looking at it, we
also should not allow XADD variant of BPF_STX.
The context rewriter is only assuming either BPF_LDX_MEM- or
BPF_STX_MEM-type operations, thus reject anything other than
that so that assumptions in the rewriter properly hold. Add
test cases as well for BPF selftests.
Fixes: d691f9e8d4 ("bpf: allow programs to write to certain skb fields")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The code for .get_multiple() has bugs:
1. The simple .get_multiple() just reads a register, masks it
and sets the return value. This is not correct: we only want to
assign values (whether 0 or 1) to the bits that are set in the
mask. Fix this by using &= ~mask to clear all bits in the mask
and then |= val & mask to set the corresponding bits from the
read.
2. The bgpio_get_multiple_be() call has a similar problem: it
uses the |= operator to set the bits, so only the bits in the
mask are affected, but it misses to clear all returned bits
from the mask initially, so some bits will be returned
erroneously set to 1.
3. The bgpio_get_set_multiple() again fails to clear the bits
from the mask.
4. find_next_bit() wasn't handled correctly, use a totally
different approach for one function and change the other
function to follow the design pattern of assigning the first
bit to -1, then use bit + 1 in the for loop and < num_iterations
as break condition.
Fixes: 80057cb417 ("gpio-mmio: Use the new .get_multiple() callback")
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull networking fixes from David Miller:
1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.
2) Memory leak in key_notify_policy(), from Steffen Klassert.
3) Fix overflow with bpf arrays, from Daniel Borkmann.
4) Fix RDMA regression with mlx5 due to mlx5 no longer using
pci_irq_get_affinity(), from Saeed Mahameed.
5) Missing RCU read locking in nl80211_send_iface() when it calls
ieee80211_bss_get_ie(), from Dominik Brodowski.
6) cfg80211 should check dev_set_name()'s return value, from Johannes
Berg.
7) Missing module license tag in 9p protocol, from Stephen Hemminger.
8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
Maloney.
9) Fix endless loop in netlink extack code, from David Ahern.
10) TLS socket layer sets inverted error codes, resulting in an endless
loop. From Robert Hering.
11) Revert openvswitch erspan tunnel support, it's mis-designed and we
need to kill it before it goes into a real release. From William Tu.
12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
net, sched: fix panic when updating miniq {b,q}stats
qed: Fix potential use-after-free in qed_spq_post()
nfp: use the correct index for link speed table
lan78xx: Fix failure in USB Full Speed
sctp: do not allow the v4 socket to bind a v4mapped v6 address
sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
ibmvnic: Fix pending MAC address changes
netlink: extack: avoid parenthesized string constant warning
ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
net: Allow neigh contructor functions ability to modify the primary_key
sh_eth: fix dumping ARSTR
Revert "openvswitch: Add erspan tunnel support."
net/tls: Fix inverted error codes to avoid endless loop
ipv6: ip6_make_skb() needs to clear cork.base.dst
sctp: avoid compiler warning on implicit fallthru
net: ipv4: Make "ip route get" match iif lo rules again.
netlink: extack needs to be reset each time through loop
tipc: fix a memory leak in tipc_nl_node_get_link()
ipv6: fix udpv6 sendmsg crash caused by too small MTU
...
Yet a few small last-minute fixes that should sneak into 4.15:
- Removal of a spurious WARN_ON() triggered by syzkaller
- Fix for ioctl races in ALSA sequencer
- Two trivial HD-audio fixup entries
-----BEGIN PGP SIGNATURE-----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=JkyD
-----END PGP SIGNATURE-----
Merge tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small last-minute fixes that should sneak into 4.15:
- remove a spurious WARN_ON() triggered by syzkaller
- fix for ioctl races in ALSA sequencer
- two trivial HD-audio fixup entries"
* tag 'sound-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: Make ioctls race-free
ALSA: pcm: Remove yet superfluous WARN_ON()
ALSA: hda - Apply the existing quirk to iMac 14,1
ALSA: hda - Apply headphone noise quirk for another Dell XPS 13 variant
- Bring back context level recursive protection in ring buffer.
The simpler counter protection failed, due to a path when
tracing with trace_clock_global() as it could not be reentrant
and depended on the ring buffer recursive protection to keep that
from happening.
- Prevent branch profiling when FORTIFY_SOURCE is enabled. It causes
50 - 60 MB in warning messages. Branch profiling should never be
run on production systems, so there's no reason that it needs to
be enabled with FORTIFY_SOURCE.
-----BEGIN PGP SIGNATURE-----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=qWqD
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Bring back context level recursive protection in ring buffer.
The simpler counter protection failed, due to a path when tracing
with trace_clock_global() as it could not be reentrant and depended
on the ring buffer recursive protection to keep that from happening.
- Prevent branch profiling when FORTIFY_SOURCE is enabled.
It causes 50 - 60 MB in warning messages. Branch profiling should
never be run on production systems, so there's no reason that it
needs to be enabled with FORTIFY_SOURCE.
* tag 'trace-v4.15-rc4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Prevent PROFILE_ALL_BRANCHES when FORTIFY_SOURCE=y
ring-buffer: Bring back context level recursive checks
While working on fixing another bug, I ran into the following panic
on arm64 by simply attaching clsact qdisc, adding a filter and running
traffic on ingress to it:
[...]
[ 178.188591] Unable to handle kernel read from unreadable memory at virtual address 810fb501f000
[ 178.197314] Mem abort info:
[ 178.200121] ESR = 0x96000004
[ 178.203168] Exception class = DABT (current EL), IL = 32 bits
[ 178.209095] SET = 0, FnV = 0
[ 178.212157] EA = 0, S1PTW = 0
[ 178.215288] Data abort info:
[ 178.218175] ISV = 0, ISS = 0x00000004
[ 178.222019] CM = 0, WnR = 0
[ 178.224997] user pgtable: 4k pages, 48-bit VAs, pgd = 0000000023cb3f33
[ 178.231531] [0000810fb501f000] *pgd=0000000000000000
[ 178.236508] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 178.311855] CPU: 73 PID: 2497 Comm: ping Tainted: G W 4.15.0-rc7+ #5
[ 178.319413] Hardware name: FOXCONN R2-1221R-A4/C2U4N_MB, BIOS G31FB18A 03/31/2017
[ 178.326887] pstate: 60400005 (nZCv daif +PAN -UAO)
[ 178.331685] pc : __netif_receive_skb_core+0x49c/0xac8
[ 178.336728] lr : __netif_receive_skb+0x28/0x78
[ 178.341161] sp : ffff00002344b750
[ 178.344465] x29: ffff00002344b750 x28: ffff810fbdfd0580
[ 178.349769] x27: 0000000000000000 x26: ffff000009378000
[...]
[ 178.418715] x1 : 0000000000000054 x0 : 0000000000000000
[ 178.424020] Process ping (pid: 2497, stack limit = 0x000000009f0a3ff4)
[ 178.430537] Call trace:
[ 178.432976] __netif_receive_skb_core+0x49c/0xac8
[ 178.437670] __netif_receive_skb+0x28/0x78
[ 178.441757] process_backlog+0x9c/0x160
[ 178.445584] net_rx_action+0x2f8/0x3f0
[...]
Reason is that sch_ingress and sch_clsact are doing mini_qdisc_pair_init()
which sets up miniq pointers to cpu_{b,q}stats from the underlying qdisc.
Problem is that this cannot work since they are actually set up right after
the qdisc ->init() callback in qdisc_create(), so first packet going into
sch_handle_ingress() tries to call mini_qdisc_bstats_cpu_update() and we
therefore panic.
In order to fix this, allocation of {b,q}stats needs to happen before we
call into ->init(). In net-next, there's already such option through commit
d59f5ffa59 ("net: sched: a dflt qdisc may be used with per cpu stats").
However, the bug needs to be fixed in net still for 4.15. Thus, include
these bits to reduce any merge churn and reuse the static_flags field to
set TCQ_F_CPUSTATS, and remove the allocation from qdisc_create() since
there is no other user left. Prashant Bhole ran into the same issue but
for net-next, thus adding him below as well as co-author. Same issue was
also reported by Sandipan Das when using bcc.
Fixes: 46209401f8 ("net: core: introduce mini_Qdisc and eliminate usage of tp->q for clsact fastpath")
Reference: https://lists.iovisor.org/pipermail/iovisor-dev/2018-January/001190.html
Reported-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Co-authored-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Co-authored-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check if p_ent->comp_mode is QED_SPQ_MODE_EBLOCK before
calling qed_spq_add_entry(). The test is fine is the mode is EBLOCK,
but if it isn't then qed_spq_add_entry() might kfree(p_ent).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sts variable is holding link speed as well as state. We should
be using ls to index into ls_to_ethtool.
Fixes: 265aeb511b ("nfp: add support for .get_link_ksettings()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix initialize the uninitialized tx_qlen to an appropriate value when USB
Full Speed is used.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dynamic stack_depth tracking in arm64 JIT is currently broken in
combination with tail calls. In prologue, we cache ctx->stack_size and
adjust SP reg for setting up function call stack, and tearing it down
again in epilogue. Problem is that when doing a tail call, the cached
ctx->stack_size might not be the same.
One way to fix the problem with minimal overhead is to re-adjust SP in
emit_bpf_tail_call() and properly adjust it to the current program's
ctx->stack_size. Tested on Cavium ThunderX ARMv8.
Fixes: f1c9eed7f4 ("bpf, arm64: take advantage of stack_depth tracking")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The check in sctp_sockaddr_af is not robust enough to forbid binding a
v4mapped v6 addr on a v4 socket.
The worse thing is that v4 socket's bind_verify would not convert this
v4mapped v6 addr to a v4 addr. syzbot even reported a crash as the v4
socket bound a v6 addr.
This patch is to fix it by doing the common sa.sa_family check first,
then AF_INET check for v4mapped v6 addrs.
Fixes: 7dab83de50 ("sctp: Support ipv6only AF_INET6 sockets.")
Reported-by: syzbot+7b7b518b1228d2743963@syzkaller.appspotmail.com
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit cea0cc80a6 ("sctp: use the right sk after waking up from
wait_buf sleep"), it may change to lock another sk if the asoc has been
peeled off in sctp_wait_for_sndbuf.
However, the asoc's new sk could be already closed elsewhere, as it's in
the sendmsg context of the old sk that can't avoid the new sk's closing.
If the sk's last one refcnt is held by this asoc, later on after putting
this asoc, the new sk will be freed, while under it's own lock.
This patch is to revert that commit, but fix the old issue by returning
error under the old sk's lock.
Fixes: cea0cc80a6 ("sctp: use the right sk after waking up from wait_buf sleep")
Reported-by: syzbot+ac6ea7baa4432811eb50@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After introducing sctp_stream structure, sctp uses stream->outcnt as the
out stream nums instead of c.sinit_num_ostreams.
However when users use sinit in cmsg, it only updates c.sinit_num_ostreams
in sctp_sendmsg. At that moment, stream->outcnt is still using previous
value. If it's value is not updated, the sinit_num_ostreams of sinit could
not really work.
This patch is to fix it by updating stream->outcnt and reiniting stream
if stream outcnt has been change by sinit in sendmsg.
Fixes: a83863174a ("sctp: prepare asoc stream for stream reconf")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy chips without CLM blob files, kernel with user helper function
returns -EAGAIN when we request_firmware(), and then driver got failed
when bringing up legacy chips. We expect the CLM blob file for legacy chip
is not existence in firmware path, but the -ENOENT error is transferred to
-EAGAIN in firmware_class.c with user helper.
Because of that, we continue with CLM data currently present in firmware
if getting error from doing request_firmware().
Cc: stable@vger.kernel.org # v4.15.y
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit d41e6858ba ("MIPS: Kconfig: Set default MIPS system type
as generic") changed the default MIPS platform to the "generic"
platform, which uses PCI_DRIVERS_GENERIC instead of PCI_DRIVERS_LEGACY,
various files in drivers/ssb/ have failed to build.
This is particularly due to the existence of struct pci_controller being
dependent on PCI_DRIVERS_LEGACY since commit c5611df968 ("MIPS: PCI:
Introduce CONFIG_PCI_DRIVERS_LEGACY"), so add that dependency to Kconfig
to prevent these files being built for the "generic" platform including
all{yes,mod}config builds.
Fixes: c5611df968 ("MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Michael Buesch <m@bues.ch>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-wireless@vger.kernel.org
Cc: linux-mips@linux-mips.org
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mips builds with BCMA host mode enabled fail in mainline and -next
with:
In file included from include/linux/bcma/bcma.h:10:0,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:8:
include/linux/bcma/bcma_driver_pci.h:218:24: error:
field 'pci_controller' has incomplete type
Bisect points to commit d41e6858ba ("MIPS: Kconfig: Set default MIPS
system type as generic") as the culprit. Analysis shows that the commmit
changes PCI configuration and enables PCI_DRIVERS_GENERIC. This in turn
disables PCI_DRIVERS_LEGACY. 'struct pci_controller' is, however, only
defined if PCI_DRIVERS_LEGACY is enabled.
Ultimately that means that BCMA_DRIVER_PCI_HOSTMODE depends on
PCI_DRIVERS_LEGACY. Add the missing dependency.
Fixes: d41e6858ba ("MIPS: Kconfig: Set default MIPS system type as ...")
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to architecture limitations, the IBM VNIC client driver is unable
to perform MAC address changes unless the device has "logged in" to
its backing device. Currently, pending MAC changes are handled before
login, resulting in an error and failure to change the MAC address.
Moving that chunk to the end of the ibmvnic_login function, when we are
sure that it was successful, fixes that.
The MAC address can be changed when the device is up or down, so
only check if the device is in a "PROBED" state before setting the
MAC address.
Fixes: c26eba03e4 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some rare conditions when running one PEAK USB-FD interface over
a non high-speed USB controller, one useless USB fragment might be sent.
This patch fixes the way a USB command is fragmented when its length is
greater than 64 bytes and when the underlying USB controller is not a
high-speed one.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before commit:
e33a9bba85 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
delayacct_blkio_end() was called after context-switching into the task which
completed I/O.
This resulted in double counting: the task would account a delay both waiting
for I/O and for time spent in the runqueue.
With e33a9bba85, delayacct_blkio_end() is called by try_to_wake_up().
In ttwu, we have not yet context-switched. This is more correct, in that
the delay accounting ends when the I/O is complete.
But delayacct_blkio_end() relies on 'get_current()', and we have not yet
context-switched into the task whose I/O completed. This results in the
wrong task having its delay accounting statistics updated.
Instead of doing that, pass the task_struct being woken to delayacct_blkio_end(),
so that it can update the statistics of the correct task.
Signed-off-by: Josh Snyder <joshs@netflix.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: <stable@vger.kernel.org>
Cc: Brendan Gregg <bgregg@netflix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-block@vger.kernel.org
Fixes: e33a9bba85 ("sched/core: move IO scheduling accounting from io_schedule_timeout() into scheduler")
Link: http://lkml.kernel.org/r/1513613712-571-1-git-send-email-joshs@netflix.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently the BSP microcode update code examines the initrd very early
in the boot process. If SME is active, the initrd is treated as being
encrypted but it has not been encrypted (in place) yet. Update the
early boot code that encrypts the kernel to also encrypt the initrd so
that early BSP microcode updates work.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180110192634.6026.10452.stgit@tlendack-t1.amdoffice.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
