Pull irq updates from Thomas Gleixner:
"The usual pile of boring changes:
- Consolidate tasklet functions to share code instead of duplicating
it
- The first step for making the low level entry handler management on
multi-platform kernels generic
- A new sysfs file which allows to retrieve the wakeup state of
interrupts.
- Ensure that the interrupt thread follows the effective affinity and
not the programmed affinity to avoid cross core wakeups.
- Two new interrupt controller drivers (Microsemi Ocelot and Qualcomm
PDC)
- Fix the wakeup path clock handling for Reneasas interrupt chips.
- Rework the boot time register reset for ARM GIC-V2/3
- Better suspend/resume support for ARM GIV-V3/ITS
- Add missing locking to the ARM GIC set_type() callback
- Small fixes for the irq simulator code
- SPDX identifiers for the irq core code and removal of boiler plate
- Small cleanups all over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
openrisc: Set CONFIG_MULTI_IRQ_HANDLER
arm64: Set CONFIG_MULTI_IRQ_HANDLER
genirq: Make GENERIC_IRQ_MULTI_HANDLER depend on !MULTI_IRQ_HANDLER
irqchip/gic: Take lock when updating irq type
irqchip/gic: Update supports_deactivate static key to modern api
irqchip/gic-v3: Ensure GICR_CTLR.EnableLPI=0 is observed before enabling
irqchip: Add a driver for the Microsemi Ocelot controller
dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller
irqchip/gic-v3: Probe for SCR_EL3 being clear before resetting AP0Rn
irqchip/gic-v3: Don't try to reset AP0Rn
irqchip/gic-v3: Do not check trigger configuration of partitionned LPIs
genirq: Remove license boilerplate/references
genirq: Add missing SPDX identifiers
genirq/matrix: Cleanup SPDX identifier
genirq: Cleanup top of file comments
genirq: Pass desc to __irq_free instead of irq number
irqchip/gic-v3: Loudly complain about the use of IRQ_TYPE_NONE
irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE
RISC-V: Move to the new GENERIC_IRQ_MULTI_HANDLER handler
genirq: Add CONFIG_GENERIC_IRQ_MULTI_HANDLER
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
driver and timer driver), which has been through 7 rounds of review on mailing
list.
It is able to boot to shell and passes most LTP-2017 testsuites in nds32 AE3XX
platform.
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78
Copied below is the ChangeLog that contains the history of this patch set:
Changes in v7:
- Update cpu binding document to add "andestech,nds32v3" as fallback
- Remove unnecessary configs of arch/nds32/Kconfig
- Use GENERIC_CALIBRATE_DELAY
- Add more help texts for minimum CPU type config
- Update defconfig because of Kconfig changed and bug fixed
- Move early_trap_init() declaration to nds32.h
- Refine dma.c
- Remove apply_relocate() in module.c and include <linux/moduleloader.h> to catch it
- Add do_kernel_restart() in machine_restart()
- Clean up setup.c to remove CONFIG_VGA_CONSOLE and some extern declaration functions
- Add negative dependency for VGA_CONSOLE on nds32
- Refine ptrace.c and arch/nds32/include/asm/ptrace.h
- Refine syscall restart flow and arch/nds32/kernel/signal.c
- Fix a bug in VDSO
- Remove the handling for kernel code unaligned accessing
- Add a description for unaligned access handling in git commit message.
- Rebase to v4.16-rc1
- Replace ACCESS_ONCE with READ_ONCE
- Replace atomic_long_dec(&mm->nr_ptes) with mm_dec_nr_ptes(mm)
- Remove print_symbol(%s) with printk(%pS)
- Add bpf_perf_event.h
- Remove init_stack and init_thread_info
Changes in v6:
- Refine naming for atl2c
- Refine ae3xx.dts
- Remove CONFIG_TIMER_ATCPIT100 in defconfig
- Refine elf.h
- Fix a vdso bug
- Separate arch patchset and timer patchset
- To select TIMER_OF in drivers/clocksource/Kconfig instead of arch/nds32/Kconfig
Changes in v5:
- Remove __NR__llseek and sys_mmap()
- Add a comment to explain that we don't have clocksource cycle counter in the CPU
- Add volatile in iounmap()
- Fix typo Featuretures to Features
- Replace CPU_CACHE_NONALIASING with !CPU_CACHE_ALIASING
- Fix a endian bug when we try to get val = of_get_property(cpu,"clock-frequency", NULL)
- Add screen_info to fix the building error when CONFIG_ VGA_CONSOLE is enabled
- Remove unnecessary msync()
- Add depends on !64BIT || BROKEN for faraday Kconfig because the descriptor only supports 32bit
- Add atl2c binding document
- Remove unnecessary include headers
- Fix a vector table bug. It placed wrong vector handlers for 2 exceptions.
- Fix a vdso bug. It may encounter TLB multi-hit exception because we accidently set it as a global page.
- Add proper isb and barrier after some cache operations
- Fix a bug in system call restart flow. $r0 ~ $r5 does not be recovered before restarting system call
- Fix the build errors for OpenRISC and SPARC because io.h changed.
- Update ae3xx.dts to support atl2c.
Changes in v4:
- Add atcpit100 timer driver due to it include vdso implementations and sent
them together with nds32 may help reviewer to review.
- Update ae3xx.dts for atcpit100 clock setting and remove vdso settings.
- To get cycle counter register by timer driver instead of dts.
- Use "depends on NDS32 || COMPILE_TEST" in atcpit100 driver because it is needed for nds32 vdso
- Update defconfig becasue kconfig rename from CONFIG_CLKSRC_ATCPIT100 to CONFIG_TIMER_ATCPIT100
- Remove ag101p.dts because we are not yet ready for ag101p platform.
- Update copyright style to SPDX-License-Identifier
- Include <linux/uaccess.h> instead of <asm/uaccess.h>
- Add local_irq_save()/local_irq_restore() to protect SR_TLB_VPN in update_mmu_cache().
- Update cpu_dcache_inval_all implementation to make sure all level cache are writeback.
Changes in v3:
- Use arch's io.h instead of generic one
- Add andestech-boards binding document
- Update nds32/cpus.txt binding document
- Remove atcpit100 timer drivers
- Select NO_BOOTMEM and delete HAVE_MEMBLOCK_NODE_MAP
- make CPU_BIG_ENDIAN and CPU_LITTLE_ENDIAN are dependent
- Add cpu type to select HWZOL/CPU_CACHE_ALIASING
- Change CPU_CACHE_NONALIASING to CPU_CACHE_ALIASING
- Remove bootarg from device tree script
- Update ag101p.dts and ae3xx.dts for correct board name.
- Clear and simplify defconfig
- Implement L2C_R_REG/ L2C_W_REG with readl/writel instead of __raw_readl/__raw_writel for endian save
- Remove early_init_dt_add_memory_arch/early_init_dt_alloc_memory_arch to use the generic ones
- Refine devicetree.c
- Fix bug https://lkml.kernel.org/r/1499782590-31366-1-git-send-ema...
- Refine irqchip/irq-ativic32.c implementations
- Add COMPILE_TEST in drivers/net/ethernet/faraday/Kconfig
- Refine cache operations
- Add CONFIG_HW_SUPPORT_UNALIGNMENT_ACCESS
- Fix ZERO_PAGE define
- Remove SA_RESTORER
- Remove uapi/asm/signal.h
- Redefine user_pt_regs
- Remove spinlock.h
- Remove __ARCH_WANT_RENAMEAT and __ARCH_WANT_SYSCALL_OFF_T from unistd.h
- Remove set_fs(USER_DS) because flush_old_exec() will do this setting
- Replace in_atomic() with faulthandler_disabled()
- Add barrier.h
- Select COMMON_CLK
- Add clk_pll in dts
- Add of_clk_init() in arch/nds32/kernel/time.c
Changes in v2:
- Set GENERIC_CALIBRATE_DELAY default n
- Add earlycon support
- Remove earlyprintk
- Add CPU_BIG_ENDIAN, CPU_LITTLE_ENDIAN support
- Refine unalignment access exception handler
- Add VMSPLIT support
- Use only one defconfig
- Change interrupt-cells from 2 to 1
- Refine andestech cpu names in bindings/nds32/cpus.txt
- Get clock frequency in dts because fpga bitmap doesn't include this feature
- Update MAINTAINERS for bindings
- Remove unused configs in Kconfig
- Refine device tree scripts
- Refine coding style
- Use generic ioremap_nocache
- Remove L2CC_PA_BASE define and its codes in head.S. It will be moved to bootloader.
- Set PHYS_OFFSET to 0x0 instead of CONFIG_MEMORY_START
- Remove unused macros
- Simplify cpu_cache_* API
- Change __asm__ __volatile__ to asm volatile
- Refine uaccess.h
- Remove unused/deprecated syscall
- Use generic posix_types.h
- Remove arch_trace_hardirqs_on/arch_trace_hardirqs_off
- Fix bug of restart syscall
- Refine syscall implementations
- Use IS_ENABLED to replace ifdef as possible
- Remove device_initcall(nds32_device_probe)
- Refine vdso implementations
- Refine copy_from_user()/copy_to_user()/clear_user()/get_user()/memmove()/memcpy()
- Refine ioremap.c
- Refine irq-ativic32.c
- Fix a bug of earlycon.c
- Export ioremap_nocache/ioremap_uc/ioremap_wc/ioremap_wt
- Add atcpit100 driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)
iQIcBAABAgAGBQJawZ28AAoJEHfB0l0b2JxExKYQAJ7btaPeIplIndrphlTQkfzW
d1AhVBhwAlvqsOcFf+kwVIqOnfcLCtzVvgc63qc6mAroDZKcd+uuqOtkC801b33i
jxcfSX802PciT3VhE8xz9OWFY9D3in/UCBhGe2OvY/cD/eC34gZhUqJhML/ioR5q
DNPvua6lgYIN9VrFds19MjRzl7RwDBqNccQoFTXWc9Hl1Vs0YdKdbkOz0IWNtoLQ
crP0v/UuHMC++WdU+MvDIEFqNVuXikg/NA+odPIbp3eF3xcmQBM0blWAi37eOKFo
rzTw7TKtL8xObjvhyzx3aYFKPpLBfuYwk8onoZlthlqcwFClZy4lzdDdDxJhKiJ6
5hilzCSqEWXB9osQsrWgAuK1rNRvroChIp6/rcdGAq33mTPLVydx7hSKELhE7wuN
UUaiJSSNRG1ZrR8tkccQpaRBjJ/gfXWGC3ys723oWz8A4bDzMkvZVzdOGOEZ+CsI
w4HKNHLeY50wztV6dDSiVPhvUXQjBH9qd2zVHlutbfulPI/XNkGRfWpEGVT1zD4y
pO3aHVJfsv+8aeyVBcXyN74O34a9HYa7811v7V5RI+uftdPhkzOwxuMQVMMJPe3s
4u4NglP7fekeWyDGCXFKOGoVOuCAUPHuzBUCFjL/cStHjrkBGVQvL1I925sJNabu
IatFh62x8Ez4m2hIf5fg
=J/YF
-----END PGP SIGNATURE-----
Merge tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux
Pull nds32 architecture support from Greentime Hu:
"This contains the core nds32 Linux port (including interrupt
controller driver and timer driver), which has been through seven
rounds of review on mailing list.
It is able to boot to shell and passes most LTP-2017 testsuites in
nds32 AE3XX platform:
Total Tests: 1901
Total Skipped Tests: 618
Total Failures: 78"
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
* tag 'nds32-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux: (44 commits)
nds32: To use the generic dump_stack()
nds32: fix building failed if using elf toolchain.
nios2: add ioremap_nocache declaration before include asm-generic/io.h.
nds32: fix building failed if using older version gcc.
dt-bindings: timer: Add andestech atcpit100 timer binding doc
clocksource/drivers/atcpit100: VDSO support
clocksource/drivers/atcpit100: Add andestech atcpit100 timer
net: faraday add nds32 support.
irqchip: Andestech Internal Vector Interrupt Controller driver
dt-bindings: interrupt-controller: Andestech Internal Vector Interrupt Controller
dt-bindings: nds32 SoC Bindings
dt-bindings: nds32 L2 cache controller Bindings
dt-bindings: nds32 CPU Bindings
MAINTAINERS: Add nds32
nds32: Build infrastructure
nds32: defconfig
nds32: Miscellaneous header files
nds32: Device tree support
nds32: Generic timers support
nds32: Loadable modules
...
Add the Device Tree binding documentation for the Microsemi Ocelot
interrupt controller that is part of the ICPU. It is connected directly to
the MIPS core interrupt controller.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The port was added back in 2000 so it's no longer even a good source
of inspiration for newer ports (if it ever was)
The last SoC (ARTPEC-3) with a CRIS main CPU was launched in 2008.
Coupled with time and working developer board hardware being
in low supply, it's time to drop the port from Linux.
So long and thanks for all the fish!
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add device binding documentation for the PDC Interrupt controller on
QCOM SoC's like the SDM845. The interrupt-controller can be used to
sense edge low interrupts and wakeup interrupts when the GIC is
non-operational.
Cc: devicetree@vger.kernel.org
Signed-off-by: Archana Sathyakumar <asathyak@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Document support for the Interrupt Controller for Externel Devices
(INTC-EX) in the Renesas M3-N (r8a77965) SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-renesas-soc@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Link: https://lkml.kernel.org/r/1519658712-22910-1-git-send-email-geert%2Brenesas@glider.be
This patch adds an irqchip driver document for the Andestech Internal Vector
Interrupt Controller.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add documentation for DT binding of Goldfish PIC driver. The compatible
string used by OS for binding the driver is "google,goldfish-pic".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miodrag Dinic <miodrag.dinic@mips.com>
Signed-off-by: Goran Ferenc <goran.ferenc@mips.com>
Signed-off-by: Aleksandar Markovic <aleksandar.markovic@mips.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This increases the interrupt cells for the 1st level interrupt controller
binding in order to describe the polarity like on the other ARM platforms.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Improve the binding example by removing all the leading 0x to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Converted using the following command:
find Documentation/devicetree/bindings -name "*.txt" -exec sed -i -e 's/([^ ])\@0x([0-9a-f])/$1\@$2/g' {} +
This is a follow up to commit 48c926cd34
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Rob Herring <robh@kernel.org>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----
iQItBAABCAAXBQJaCwaSEBxyb2JoQGtlcm5lbC5vcmcACgkQ+vtdtY28YcNzeA/8
C8uQhSsX2+UQZvFzcEA8KQAMGT3kYdrcf+gidRKwCEUWg1qscUEpTb3n3Rm5NUbU
RPD1s6GSlh6fJCMHDTQ6Tti/T59L7nZa2/AIGmUishGu4x4q1o18AobpFJmYP/EM
SJPwnmm5RV9WcZFao1y+sY3Xtn8DStxHO4cS+dyF5/EvPN9D8nbLJfu7bgTBAZww
HktIMB9kx+GTipRQZBvBwXoy5MJjthIZub4XwzesA4tGananj4cXlc0xaVxpdYy3
5bO6q5F7cbrZ2uyrF+oIChpCENK4VaXh80m0WHc8EzaG++shzEkR4he1vYkwnV+I
OYo4vsUg9dP8rBksUG1eYhS8fJKPvEBRNP7ETT5utVBy5I/tDEbo/crmQZRTIDIC
hZbhcdZlISZj0DzkMK2ZHQV9UYtRWzXrJbZHFIPP12GCyvXVxYJUIWb9iYnUYSon
KugygsFSpZHMWmfAhemw5/ctJZ19qhM5UIl2KZk5tMBHAf466ILmZjg0me6fYkOp
eADfwHJ1dLMdK79CVMHSfp+vArcZXp35B16c3sWpJB36Il97Mc/9siEufCL4GKX7
IBBnQBlbpSBKBejWVyI7Ip/Xp5u4qAQD+ZMJ9oLqBRqfWerHbDuOERlEOgwGqJYr
9v4HvP7V8eVUvAdqXka4EBfCyAgUzXDAxG2Dfmv9vGU=
=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a description of the External Interrupt Unit (EXIU) interrupt
controller as found on the Socionext SynQuacer SoC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
IPI driver for the Open Multi-Processor Interrupt Controller (ompic) as
described in the Multi-core support section of the OpenRISC 1.2
architecture specification:
https://github.com/openrisc/doc/raw/master/openrisc-arch-1.2-rev0.pdf
Each OpenRISC core contains a full interrupt controller which is used in
the SMP architecture for interrupt balancing. This IPI device, the
ompic, is the only external device required for enabling SMP on
OpenRISC.
Pending ops are stored in a memory bit mask which can allow multiple
pending operations to be set and serviced at a time. This is mostly
borrowed from the alpha IPI implementation.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
[shorne@gmail.com: converted ops to bitmask, wrote commit message]
Signed-off-by: Stafford Horne <shorne@gmail.com>
Meson8 uses the same GPIO interrupt controller IP block as the other
Meson SoCs. A total of 134 pins can be spied on, which is the sum of:
- 22 pins on bank GPIOX
- 17 pins on bank GPIOY
- 30 pins on bank GPIODV
- 10 pins on bank GPIOH
- 15 pins on bank GPIOZ
- 7 pins on bank CARD
- 19 pins on bank BOOT
- 14 pins in the AO domain
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This commit adds the device tree bindings description for Amlogic's GPIO
interrupt controller available on the meson8b, gxbb and gxl SoC families
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Document support for the Interrupt Controller for Externel Devices
(INTC-EX) in the Renesas M3-W (r8a7796), V3M (r8a77970), and D3
(r8a77995) SoCs.
No driver update is needed.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Currently, the examples are using 2MB for the ITS size. Per the
specification (section 8.18 in ARM IHI 0069D), the ITS address map is
128KB.
Update the examples to match the specification.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The ls1012a implements only 1 MSI controller, and it is the same as
ls1043a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
A MSI controller of LS1043a v1.0 only includes one MSIR and
is assigned one GIC interrupt. In order to support affinity,
LS1043a v1.1 MSI is assigned 4 MSIRs and 4 GIC interrupts.
But the MSIR has the different offset and only supports 8 MSIs.
The bits between variable bit_start and bit_end in structure
ls_scfg_msir are used to show 8 MSI interrupts. msir_irqs and
msir_base are added to describe the difference of MSI between
LS1043a v1.1 and other SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The patch is to fix typo of the Layerscape SCFG MSI dts compatible
strings. "1" is replaced by "l".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
UniPhier SoCs contain AIDET (ARM Interrupt Detector). This is intended
to provide additional features that are not covered by GIC. The main
purpose is to provide logic inverter to support low level and falling
edge trigger types for interrupt lines from on-board devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds dt-binding documentation for Mediatek MT2712.
Only include very basic items: cpu, gic and uart.
Signed-off-by: YT Shen <yt.shen@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
-----BEGIN PGP SIGNATURE-----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=DNwf
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- vsprintf format specifier %pOF for device_node's. This will enable us
to stop storing the full node names. Conversion of users will happen
next cycle.
- Update documentation to point to DT specification instead of ePAPR.
- Split out graph and property functions to a separate file.
- New of-graph functions for ALSA
- Add vendor prefixes for RISC-V, Linksys, iWave Systems, Roofull,
Itead, and BananaPi.
- Improve dtx_diff utility filename printing.
* tag 'devicetree-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (32 commits)
of: document /sys/firmware/fdt
dt-bindings: Add RISC-V vendor prefix
vsprintf: Add %p extension "%pOF" for device tree
of: find_node_by_full_name rewrite to compare each level
of: use kbasename instead of open coding
dt-bindings: thermal: add file extension to brcm,ns-thermal
of: update ePAPR references to point to Devicetree Specification
scripts/dtc: dtx_diff - Show real file names in diff header
of: detect invalid phandle in overlay
of: be consistent in form of file mode
of: make __of_attach_node() static
of: address.c header comment typo
of: fdt.c header comment typo
of: make of_fdt_is_compatible() static
dt-bindings: display-timing.txt convert non-ascii characters to ascii
Documentation: remove overlay-notes reference to non-existent file
dt-bindings: usb: exynos-usb: Add missing required VDD properties
dt-bindings: Add vendor prefix for Linksys
MAINTAINERS: add device tree ABI documentation file
of: Add vendor prefix for iWave Systems Technologies Pvt. Ltd
...
Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer
gets added, this one stands out for being relatively fast,
affordable and well₋supported, compared to many boards that
only fall into one or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform
and corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win,
Orangepi Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single
board computers and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB
automotive development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets
extended significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=E8pa
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"Device-tree updates for arm64 platforms. For the first time I can
remember, this is actually larger than the corresponding branch for
32-bit platforms overall, though that has more individual changes.
A significant portion this time is due to added machine support:
- Initial support for the Realtek RTD1295 SoC, along with the Zidoo
X9S set-top-box
- Initial support for Actions Semi S900 and the Bubblegum-96
single-board-cёmputer.
- Rockchips support for the rk3399-Firefly single-board-computer gets
added, this one stands out for being relatively fast, affordable
and well₋supported, compared to many boards that only fall into one
or two of the above categories.
- Mediatek gains support for the mt6797 mobile-phone SoC platform and
corresponding evaluation board.
- Amlogic board support gets added for the NanoPi K2 and S905x
LibreTech CC single-board computers and the R-Box Pro set-top-box
- Allwinner board support gets added for the OrangePi Win, Orangepi
Zero Plus 2, NanoPi NEO2 and Orange Pi Prime single board computers
and the SoPine system-on-module.
- Renesas board support for Salvator-XS and H3ULCB automotive
development systems.
- Socionext Uniphier board support for LD11-global and LD20-global,
whatever those may be.
- Broadcom adds support for the new Stingray communication processor
in its iProc family, along with two reference boards.
Other updates include:
- For the hisicon platform, support for Hi3660-Hikey960 gets extended
significantly.
- Lots of smaller updates for Renesas, Amlogic, Rockchip, UniPhier,
Broadcom, Allwinner, Hisilicon, Qualcomm, Marvell, and NXP"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (243 commits)
ARM64: dts: marvell: armada37xx: Fix timer interrupt specifiers
Revert "arm64: dts: marvell: add dma-mask in crypto nodes for 7k/8k"
arm64: dts: mediatek: don't include missing file
ARM64: dts: meson-gxl: Add Libre Technology CC support
dt-bindings: arm: amlogic: Add Libre Technology CC board
dt-bindings: add Libre Technology vendor prefix
arm64: dts: marvell: enable GICP and ICU on Armada 7K/8K
arm64: dts: zte: Use - instead of @ for DT OPP entries
arm64: dts: marvell: add gpio support for Armada 7K/8K
arm64: dts: marvell: add pinctrl support for Armada 7K/8K
arm64: dts: marvell: use new binding for the system controller on cp110
arm64: dts: marvell: remove *-clock-output-names on cp110
arm64: dts: marvell: use new bindings for xor clocks on ap806
arm64: dts: marvell: mcbin: enable the mdio node
arm64: dts: Add Actions Semi S900 and Bubblegum-96
dt-bindings: Add vendor prefix for uCRobotics
arm64: dts: marvell: add xmdio nodes for 7k/8k
arm64: dts: marvell: add a comment on the cp110 slave node status
arm64: dts: marvell: remove cpm crypto nodes from dts files
arm64: dts: marvell: cp110: enable the crypto engine at the SoC level
...
This commit adds the Device Tree binding documentation for the Marvell
ICU interrupt controller, which collects wired interrupts from the
devices located into the CP110 hardware block of Marvell Armada 7K/8K,
and converts them into SPI interrupts in the GIC located in the AP
hardware block, using the GICP extension.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Devicetree Specification has superseded the ePAPR as the
base specification for bindings. Update files in Documentation
to reference the new document.
First reference to ePAPR in Documentation/devicetree/bindings/arm/cci.txt
is generic, remove it.
Some files are not updated because there is no hypervisor chapter
in the Devicetree Specification:
Documentation/devicetree/bindings/powerpc/fsl/msi-pic.txt
Documenation/virtual/kvm/api.txt
Documenation/virtual/kvm/ppc-pv.txt
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This commit adds the Device Tree binding documentation for the Marvell
GICP, an extension to the GIC that allows to trigger GIC SPI interrupts
using memory transactions. It is used by the ICU unit in the Marvell
CP110 block to turn wired interrupts inside the CP into SPI interrupts
at the GIC level in the AP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
In addition to introducing the new compatible string the bindings
description is reworked to be more generic.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The A31 and later have an R_INTC block which handles the NMI interrupt
pin on the SoC. This interrupt pin is used by the external PMIC to
signal interrupts to the SoC.
While this hardware block is undocumented, the interrupt offsets
combined with the register regions for the existing "sun6i-a31-sc-nmi"
compatible line up with the old interrupt controller found on the A10.
Experiments show that only the first 32 interrupt lines can be enabled,
and only the first (NMI) interrupt is actually connected.
This patch adds a new, properly named compatible for the A31 R_INTC
block, which requires the register region to be properly aligned to
the block boundary. For comparison, the old "sun6i-a31-sc-nmi"
compatible had its register region aligned with the first used
register. This didn't match up with the memory map in the SoC's
datasheet/user manual.
Since the new compatible supercedes the old one, deprecate the old one.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This adds dt-binding documentation for MediaTek MT7622 SoC
which currently only includes basic items such as ARM CPU,
MediaTek SYSIRQ and UART.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
All SoCs supported up to now rely on the fallback binding of mt6577.
Fix the binding description to reflect this.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
This adds dt-binding documentation for Mediatek MT6797. Only
include very basic items, gic, uart timer and cpu.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
- Fix sparse warnings in drivers/of/.
- Add more overlay unittests.
- Update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names.
- Add a common DT modalias function.
- Move trivial-devices.txt up and out of i2c dir.
- ARM NVIC interrupt controller binding.
- Vendor prefixes for Sensirion, Dioo, Nordic, ROHM.
- Correct some binding file locations.
-----BEGIN PGP SIGNATURE-----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=ca1M
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- fix sparse warnings in drivers/of/
- add more overlay unittests
- update dtc to v1.4.4-8-g756ffc4f52f6. This adds more checks on dts
files such as unit-address formatting and stricter character sets for
node and property names
- add a common DT modalias function
- move trivial-devices.txt up and out of i2c dir
- ARM NVIC interrupt controller binding
- vendor prefixes for Sensirion, Dioo, Nordic, ROHM
- correct some binding file locations
* tag 'devicetree-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (24 commits)
of: fix sparse warnings in fdt, irq, reserved mem, and resolver code
of: fix sparse warning in of_pci_range_parser_one
of: fix sparse warnings in of_find_next_cache_node
of/unittest: Missing unlocks on error
of: fix uninitialized variable warning for overlay test
of: fix unittest build without CONFIG_OF_OVERLAY
of: Add unit tests for applying overlays
of: per-file dtc compiler flags
fpga: region: add missing DT documentation for config complete timeout
of: Add vendor prefix for ROHM Semiconductor
of: fix "/cpus" reference leak in of_numa_parse_cpu_nodes()
of: Add vendor prefix for Nordic Semiconductor
dt-bindings: arm,nvic: Binding for ARM NVIC interrupt controller on Cortex-M
dtc: update warning settings for new bus and node/property name checks
scripts/dtc: Update to upstream version v1.4.4-8-g756ffc4f52f6
scripts/dtc: automate getting dtc version and log in update script
of: Add function for generating a DT modalias with a newline
of: fix of_device_get_modalias returned length when truncating buffers
Documentation: devicetree: move trivial-devices out of I2C realm
dt-bindings: add vendor prefix for Dioo
..
This commit adds the device tree binding document for
the mediatek cirq.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This describes how to specify multiple base addresses for sysirq
in mediatek platforms.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we merged the Gemini interrupt controller it was not yet
discovered that this IP block is actually a standard Faraday
Technology interrupt controller.
As the IP block will probably appear in other designs as well,
let's augment the DT bindings to reflect that it is first and
foremost a standard Faraday part with a function name (FTINTC010)
so that people reusing the IP easily find the driver they need.
Sorry for the mistakes due to lack of information.
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
A total of 380 patches this time, mostly adding support for more hardware
in the device tree descriptions. There is not much exciting here for 4.11,
but I've tried my best to condense the information from the pull requests
I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now
gets fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already
supported chips
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP architecture
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero,
all based on Allwinner SoCs
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam i.Core
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas, qcom,
rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic,
eeprom, mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ucQ/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
- Intc imporvements [Yuriy]
- VDK platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WPBu
-----END PGP SIGNATURE-----
Merge tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
- Intc imporvements [Yuriy]
- VDK platform updates [Alexey]
* tag 'arc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: [plat-*] ARC_HAS_COH_CACHES no longer relevant
ARCv2: intc: Delete useless comments in Device Trees
ARCv2: IDU-intc: Delete deprecated parameters in Device Trees
ARCv2: IDU-intc: mask all common interrupts by default
ARCv2: IDU-intc: Use build registers for getting numbers of interrupts
ARCv2: intc: Set default priority for all core interrupts
ARCv2: intc: Use runtime value of irq count for setting up intc
ARCv2: intc: Rework the build time irq count information
ARC: [intc-*]: confine NR_CPU_IRQS to intc code
ARCv2: intc: Use ARC_REG_STATUS32 for addressing STATUS32 reg
arc: vdk: Add support of UIO
arc: vdk: Add support of MMC controller
arc: vdk: Disable halt on reset
This adds device tree bindings for the Cortina Gemini interrupt
controller. They are pretty standard.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
