The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of hard-coded "i2c-10EC5670:00", use the translation helper to
avoid the mismatch between i2c-codec and ACPI strings just like what
we've done for bytcr_rt5640. This gives more robust binding on funky
devices like Dell Wyse 3040.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Execution 'ethtool -S' on fec device that is down causes OOPS on Vybrid
board:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xe0898200
pgd = ddecc000
[e0898200] *pgd=9e406811, *pte=400d1653, *ppte=400d1453
Internal error: : 1008 [#1] SMP ARM
...
Reason of OOPS is that fec_enet_get_ethtool_stats() accesses fec
registers while IPG clock is stopped by PM.
Fix that by caching statistics in fec_enet_private. Cache is initialized
at device probe time, and updated at statistics request time if device
is up, and also just before turning device off on down path.
Additional locking is not needed, since cached statistics is accessed
either before device is registered, or under rtnl_lock().
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an issue about pop noise in NAU88L25 as follows.
Issue 54078: Chell_headphone pop back from S3
(1)Play directly to hw, bypassing CRAS:
sox -b 16 -n -t alsa hw:0,0 synth sine 200 sine 200
(2)Close lid or powerd_dbus_suspend, then press a key to resume.
(3)no audio after resume
(4)Audio will be back after close then reopen the pcm device.
After verification, we find one defect is that semaphone lock is not
long enough and expired. In this situation, the playback comes back
early but pauses a while to wait for the crosstalk detection done.
But the detection spends too much time and lock time is up. Therefore,
the playback and jack detection sequence interfere to each other.
That breaks sequence and makes noise. The driver extends the lock
time for the issue.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The usage pattern of kthread worker in Intel SST drivers can be
replaced gracefully with the normal workqueue, which is more light-
weight and easier to manage in general. Let's do it.
While in the replacement, move the schedule_work() call inside the
spinlock for excluding the race, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to modify the state of some of our own pins and are currently
not taking account that the pin name may have a name_prefix applied
to it.
Replace the snd_soc_dapm_x_pin functions with the equivalent
snd_soc_component_x_pin functions so that any name_prefix will be
handled automatically.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's often the case that a codec driver will need to control its
own pins. However, if a name_prefix has been applied to this codec it
must be included in the name passed to any of the snd_soc_dapm_x_pin()
functions.
The behaviour of the existing pin control functions is reasonable, since
you may want to search for a fully-specified name within the scope of an
entire card. This means that we can't apply the prefix in these functions
because it will break card-scope searches.
Constructing a prefixed string "manually" in codec drivers leads to a lot
of repetition of the same code.
To make this tidier in codec drivers this patch adds a new set of
equivalent functions that take a struct snd_soc_component instead of a
dapm context and automatically add the component's name_prefix to the
given name. This makes it a simple change in codec drivers to be
prefix-safe.
The new functions are not quite trivial enough to be inlines and the
compiler won't be able to compile-away any part of them.
Although it looks somewhat inefficient to have to allocate a temporary
buffer and combine strings, the current design of the widget list
doesn't lend itself to a more optimized implementation - it's a single
list of all widgets on a card and is searched linearly for a matching
string. As pin state changes are generally low-frequency events it's
unlikely to be a significant issue - at least not enough to rewrite the
widget list handling just for this.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
vxlan_fdb_append may return error, so add the proper check,
otherwise it will cause memory leak.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Changes in v2:
- Unnecessary to initialize rc to zero.
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt5670 driver supports also RT5672 codec, but its ACPI ID is missing.
This was found on Dell Wyse 3040 box.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dell Wyse 3040 requires the platform workaround for enabling dmic and
jack detection as defined for Braswell CRB.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing ACPI ID 10EC5672 for Cherry Trail, which bounds with
cht-bsw-rt5672 driver. This combination was found on Dell Wyse 3040.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If nf_ct_frag6_gather() returns an error other than -EINPROGRESS, it
means that we still have a reference to the skb. We should free it
before returning from handle_fragments, as stated in the comment above.
Fixes: daaa7d647f ("netfilter: ipv6: avoid nf_iterate recursion")
CC: Florian Westphal <fw@strlen.de>
CC: Pravin B Shelar <pshelar@ovn.org>
CC: Joe Stringer <joe@ovn.org>
Signed-off-by: Daniele Di Proietto <diproiettod@ovn.org>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both asn1 headers are included by rsa_helper.c, so rsa_helper.o
should explicitly depend on them.
Signed-off-by: David Michael <david.michael@coreos.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When using SGs, only heap memory (memory that is valid as per
virt_addr_valid) is allowed to be referenced. The CTR DRBG used to
reference the caller-provided memory directly in an SG. In case the
caller provided stack memory pointers, the SG mapping is not considered
to be valid. In some cases, this would even cause a paging fault.
The change adds a new scratch buffer that is used unconditionally to
catch the cases where the caller-provided buffer is not suitable for
use in an SG. The crypto operation of the CTR DRBG produces its output
with that scratch buffer and finally copies the content of the
scratch buffer to the caller's buffer.
The scratch buffer is allocated during allocation time of the CTR DRBG
as its access is protected with the DRBG mutex.
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When handling inbound packets, the two halves of the sequence number
stored on the skb are already in network order.
Fixes: 000ae7b269 ("esp6: Switch to new AEAD interface")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When handling inbound packets, the two halves of the sequence number
stored on the skb are already in network order.
Fixes: 7021b2e1cd ("esp4: Switch to new AEAD interface")
Signed-off-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We grab the struct_mutex in intel_crtc_page_flip, but if we are wedged
or a reset is in progress we bail early but never seem to actually
release the lock.
Fixes: 7f1847ebf4 ("drm/i915: Simplify checking of GPU reset_counter in display pageflips")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161128103648.9235-1-matthew.auld@intel.com
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v4.7+
(cherry picked from commit ddbb271aea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On the DMA mapping error path, sg may be NULL (it has already been
marked as the last scatterlist entry), and we should avoid dereferencing
it again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e227330223 ("drm/i915: avoid leaking DMA mappings")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/20161114112930.2033-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
(cherry picked from commit b17993b7b2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
It doesn't support to run 32bit 'ip' to set xfrm objdect on 64bit host.
But the return value is unknown for user program:
ip xfrm policy list
RTNETLINK answers: Unknown error 524
Replace ENOTSUPP with EOPNOTSUPP:
ip xfrm policy list
RTNETLINK answers: Operation not supported
Signed-off-by: Yi Zhao <yi.zhao@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Thanks for pulling the previous patch for HDLCD. Unfortunately,
yesterday Robin Murphy discovered another issue while playing with
CMA allocation sizes, which he has submitted a fix for.
* 'for-upstream/hdlcd' of git://linux-arm.org/linux-ld:
drm: hdlcd: Fix cleanup order
Johan Hovold says:
====================
net: fix fixed-link phydev leaks
This series fixes failures to deregister and free fixed-link phydevs
that have been registered using the of_phy_register_fixed_link()
interface.
All but two drivers currently fail to do this and this series fixes most
of them with the exception of a staging driver and the stmmac drivers
which will be fixed by follow-on patches.
Included are also a couple of fixes for related of-node leaks.
Note that all patches except the of_mdio one have been compile-tested
only.
Also note that the series is against net due to dependencies not yet in
net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on slave-setup errors and on slave destroy.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Also remember to put the of-node reference on probe errors.
Fixes: 1bb6aa56bb ("net: davinci_emac: Add support for fixed-link
PHY")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 077742dac2 ("dwc_eth_qos: Add support for Synopsys DWC Ethernet
QoS")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on initialisation errors and on device
close after having disconnected the PHY.
Fixes: b4bc88a868 ("ravb: Add fixed-link support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on initialisation errors and on uninit.
Fixes: 0c72c50f6f ("net-next: mediatek: add fixed-phy support")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 83895bedee ("net: mvneta: add support for fixed links")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 87009814cd ("ucc_geth: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: be40364544 ("gianfar: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: bb74d9a4a8 ("fs_enet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 407066f8f3 ("net: fec: Support phys probed from devicetree and
fixed-link")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Note that we're still leaking any fixed-link PHY registered in the
non-OF probe path.
Fixes: 9abf0c2b71 ("net: bcmgenet: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 186534a3f8 ("net: systemport: use the new fixed PHY helpers")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: c7dfe3abf4 ("net: ethernet: nb8800: support fixed-link DT
node")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link PHY registered using
of_phy_register_fixed_link() on probe errors and on driver unbind.
Fixes: 7cdbc6f74f ("altera tse: add support for fixed-links.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to deregister fixed-link PHYs registered using
of_phy_register_fixed_link().
Convert the two drivers that care to deregister their fixed-link PHYs to
use the new helper, but note that most drivers currently fail to do so.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to drop the reference taken by of_parse_phandle() before
returning from dsa_slave_phy_setup().
Note that this also modifies the PHY priority so that any fixed-link
node is only parsed when no phy-handle is given, which is in accordance
with the common scheme for this.
Fixes: 0d8bcdd383 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regression fixes for PX and a powerplay fix.
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix check for port PM availability
drm/amdgpu: fix check for port PM availability
drm/amd/powerplay: initialize the soft_regs offset in struct smu7_hwmgr
- PAE40 crash [Yuriy]
- Disabling IO-Coherency by default
- Using a different inline asm constraint for Zero Overhead loops
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M8Kh
-----END PGP SIGNATURE-----
Merge tag 'arc-4.9-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- fix PAE40 crash [Yuriy]
- disable IO-Coherency by default
- use a different inline asm constraint for Zero Overhead loops
* tag 'arc-4.9-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: mm: PAE40: Fix crash at munmap
ARC: mm: IOC: Don't enable IOC by default
ARC: Don't use "+l" inline asm constraint
As it may get stale and lead to use after free.
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexander Duyck <aduyck@mirantis.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Fixes: cbc53e08a7 ("GSO: Add GSO type for fixed IPv4 ID")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be symmetric to hashtable insert and remove filter from hashtable only
in case skip sw flag is not set.
Fixes: e69985c67c ("net/sched: cls_flower: Introduce support in SKIP SW flag")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull() can reallocate skb->head, we need to reload dh pointer
in dccp_invalid_packet() or risk use after free.
Bug found by Andrey Konovalov using syzkaller.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a hardware issue happened as described by inline comments, the register
write pattern looks like the following:
<write ~MACB_BIT(RE)>
+ wmb();
<write MACB_BIT(RE)>
There might be a memory barrier between these two write operations, so add wmb
to ensure an flip from 0 to 1 for NCR.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On macb only (not gem), when a RX queue corruption was detected from
macb_rx(), the RX queue was reset: during this process the RX ring
buffer descriptor was initialized by macb_init_rx_ring() but we forgot
to also set bp->rx_tail to 0.
Indeed, when processing the received frames, bp->rx_tail provides the
macb driver with the index in the RX ring buffer of the next buffer to
process. So when the whole ring buffer is reset we must also reset
bp->rx_tail so the driver is synchronized again with the hardware.
Since macb_init_rx_ring() is called from many locations, currently from
macb_rx() and macb_init_rings(), we'd rather add the "bp->rx_tail = 0;"
line inside macb_init_rx_ring() than add the very same line after each
call of this function.
Without this fix, the rx queue is not reset properly to recover from
queue corruption and connection drop may occur.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 9ba723b081 ("net: macb: remove BUG_ON() and reset the queue to handle RX errors")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
