For sg buffer list use case, we need to add ISP for each TRB, and
add CHAIN bit for each TRB except for the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It only dumps the first TRB per request, it is not useful if only dump
the first TRB when there are several TRBs per request. We improve it by
dumpping all TRBs per request in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It needs to use request->num_mapped_sgs to indicate mapped sg number,
the request->num_sgs is the sg number before the mapping. These two
entries have different values for the platforms which iommu or
swiotlb is used. Besides, it needs to use correct sg APIs for
mapped sg list for TRB assignment.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If cdns3_gadget_start is failed, it never frees cdns3_device structure.
Meanwhile, there is no release function for gadget device, it causes
there is no sync with driver core.
To fix this, we add release function for gadget device, and free
cdns3_device structure at there. Meanwhile, With the new UDC core
APIs, we could work with driver core better to handle memory leak
issue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After commit f4cfe5ce60 ("usb: cdns3: gadget: improve the
set_configuration handling"), the software will inform the
hardware the request has finished at cdns3_ep0_complete_setup.
The configuration set bit is only set after request has finished,
so it needs to move waiting operation after that. Meanwhile,
if it is timeout, it will show warning message and return error.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some PHYs may need to enter related mode, and do some settings.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is meaningless to handle any interrupts after disconnecting
with host
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Below is the recommendation from Cadence designer:
Using this bit to be sure that PHY clock is keeping up in active
state. It's good to keep Fast Access bit enabled as long as there
is any access to USB register.
It is used to fix the potential ARM core hang when visit controller
register after DEVDS (.pullup is cleared) is set, the threaded irq
may be scheduled at that time.
Cc: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the board uses role switch class for switching the role, it should
not depends on SoC OTG hardware siginal any more, so quit early.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB2.0 PHY hangs in Rx Compliance test when the incoming packet
amplitude is varied below and above the Squelch Level of
Receiver during the active packet multiple times.
Version 1 of the controller allows PHY to be reset when RX fail condition
is detected to work around the above issue. This feature is
disabled by default and needs to be enabled using a bit from
the newly added PHYRST_CFG register. This patch enables the workaround.
There is no way to know controller version before device controller
is started and the workaround needs to be applied for both host and
device modes, so we rely on a DT property do decide when to
apply the workaround.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Introduce runtime PM and wakeup interrupt handler for cdns3,
the runtime PM is default off since other cdns3 may not
implement glue layer support for runtime PM.
One typical wakeup event use case is xHCI runtime suspend will clear
USBCMD.RS bit, after that the xHCI will not trigger any interrupts,
so its parent (cdns core device) needs to resume xHCI device when
any (wakeup) events occurs at host port.
When the controller is in low power mode, the lpm flag will be set.
The interrupt triggered later than lpm flag is set considers as
wakeup interrupt and handled at cdns_wakeup_irq. Once the wakeup
occurs, it first disables interrupt to avoid later interrupt
occurrence since the controller is in low power mode at that
time, and access registers may be invalid at that time. At wakeup
handler, it will call pm_request_resume to wakeup xHCI device, and
at runtime resume handler, it will enable interrupt again.
The API platform_suspend is introduced for glue layer to implement
platform specific PM sequence.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since we have both USB2 and USB3 PHYs for cdns3 controller, it is
better we have unity APIs to handle both USB2 and USB3's power, it
could simplify code for error handling and further power management
implementation.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch split function cdns3_drd_switch_gadget and
cdns3_drd_switch_host into:
- cdns3_drd_host_on
- cdns3_drd_host_off
- cdns3_drd_gadget_on
- cdns3_drd_gadgett_off
These functions don't have any shared code so it's better to
have smaller, faster and easier functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Some error code can be preserved, so we can remove overwriting
error code returned by some functions.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch adds 2 definitions that make it easier to understand the code.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch changes return type from int to bool for
cdns3_is_host and cdns3_is_device functions.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
IRQ_NONE can be returned indirect.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Patch remove some variables initialization from core.c and drd.c
file.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Function is not used in driver so it can be removed.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It doesn't need to enable/disable L1 on the fly for EP0 transfer,
we only need to enable L1 after SET_CONFIGURATION.
This code may be introduced by careless.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
- Delete the duplicated EP_CMD_ERDY and EP_CMD_REQ_CMPL setting
- Prepare the next setup before setting EP_CMD_ERDY and EP_CMD_REQ_CMPL,
it could avoid a bug that DMA hang at EP0 OUT for DEV_VER_NXP_V1
- Delete the duplicated cdns3_set_hw_configuration calling at
cdns3_req_ep0_set_configuration, the composite.c will handle
this request, and call .ep0_queue back, and at .ep_queue it will
call cdns3_set_hw_configuration.
- Move cdns3_allow_enable_l1 into cdns3_set_hw_configuration since
it is part of this function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719160910.60018-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
'zlp' was documented, but in the wrong place.
Fixes the following W=1 kernel build warning(s):
drivers/usb/cdns3/ep0.c:36: warning: Function parameter or member 'zlp' not described in 'cdns3_ep0_run_transfer'
drivers/usb/cdns3/ep0.c:705: warning: Excess function parameter 'zlp' description in 'cdns3_gadget_ep0_queue'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-23-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mainline misspelled function argument descriptions. Also one
formatting issue with a missing '@' identifier.
Fixes the following W=1 build warnings:
drivers/usb/cdns3/gadget.c:653: warning: Function parameter or member 'priv_ep' not described in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:653: warning: Excess function parameter 'priv_dev' description in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:1088: warning: Function parameter or member 'request' not described in 'cdns3_ep_run_transfer'
drivers/usb/cdns3/gadget.c:2574: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2574: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2898: warning: Function parameter or member 'priv_dev' not described in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:2898: warning: Excess function parameter 'cdns3' description in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:3210: warning: Function parameter or member 'cdns' not described in 'cdns3_gadget_init'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-18-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add some missing function argument descriptions for 'ep', 'desc'
and 'zlp', and correct spelling/bitrot issues surrounding the
correct spelling of present args.
Fixes the following W=1 warnings:
drivers/usb/cdns3/ep0.c:36: warning: Function parameter or member 'zlp' not described in 'cdns3_ep0_run_transfer'
drivers/usb/cdns3/ep0.c:236: warning: Function parameter or member 'ctrl' not described in 'cdns3_req_ep0_get_status'
drivers/usb/cdns3/ep0.c:236: warning: Excess function parameter 'ctrl_req' description in 'cdns3_req_ep0_get_status'
drivers/usb/cdns3/ep0.c:411: warning: Function parameter or member 'ctrl' not described in 'cdns3_req_ep0_handle_feature'
drivers/usb/cdns3/ep0.c:411: warning: Excess function parameter 'ctrl_req' description in 'cdns3_req_ep0_handle_feature'
drivers/usb/cdns3/ep0.c:661: warning: Function parameter or member 'ep' not described in 'cdns3_gadget_ep0_enable'
drivers/usb/cdns3/ep0.c:661: warning: Function parameter or member 'desc' not described in 'cdns3_gadget_ep0_enable'
drivers/usb/cdns3/ep0.c:671: warning: Function parameter or member 'ep' not described in 'cdns3_gadget_ep0_disable'
drivers/usb/cdns3/ep0.c:867: warning: Function parameter or member 'priv_ep' not described in 'cdns3_init_ep0'
drivers/usb/cdns3/ep0.c:867: warning: Excess function parameter 'ep_priv' description in 'cdns3_init_ep0'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Pawel Jez <pjez@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 3 misspellings and 1 incorrect format used in this file's
kerneldoc function headers. Fixing them squashes the following W=1
kernel build warnings:
drivers/usb/cdns3/gadget.c:653: warning: Function parameter or member 'priv_ep' not described in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:653: warning: Excess function parameter 'priv_dev' description in 'cdns3_wa2_descmissing_packet'
drivers/usb/cdns3/gadget.c:1088: warning: Function parameter or member 'request' not described in 'cdns3_ep_run_transfer'
drivers/usb/cdns3/gadget.c:2574: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2574: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_set_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Function parameter or member 'priv_ep' not described in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2595: warning: Excess function parameter 'ep' description in '__cdns3_gadget_ep_clear_halt'
drivers/usb/cdns3/gadget.c:2898: warning: Function parameter or member 'priv_dev' not described in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:2898: warning: Excess function parameter 'cdns3' description in 'cdns3_init_eps'
drivers/usb/cdns3/gadget.c:3210: warning: Function parameter or member 'cdns' not described in 'cdns3_gadget_init'
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-14-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If it is 'int', it can't stands for the highest bit for 32-bit
number, since the largest 'int' is 0x7fffffff.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is reported by Coverity scan, and fixed it by declare the reg as
unsigned long.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value '0' is duplicated with USB_DIR_OUT
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200623031001.8469-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The other thread may access other endpoints when the cdns3_check_new_setup
is handling, add spinlock to protect it.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It should use the correct direction value from register, not depends
on previous software setting. It fixed the EP number wrong issue at
trace when the TRBERR interrupt occurs for EP0IN.
When the EP0IN IOC has finished, software prepares the setup packet
request, the expected direction is OUT, but at that time, the TRBERR
for EP0IN may occur since it is DMULT mode, the DMA does not stop
until TRBERR has met.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'tmode' is ctrl->wIndex, changing it as the real test
mode value for register assignment.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jun Li <jun.li@nxp.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200623030918.8409-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the TEST_ defines in the usb/ch9.h files did not have
the USB_ prefix on it, making it a bit confusing when reading the file,
as well as not the nicest thing to do in a uapi file.
So fix that up and add the USB_ prefix on to them, and fix up all
in-kernel usages. This included deleting the duplicate copy in the
net2272.h file.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jules Irenge <jbi.octave@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: Rob Gill <rrobgill@protonmail.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Bin Liu <b-liu@ti.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----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=OiS0
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
Each setup stage will prepare status stage at cdns3_ep0_setup_phase,
it doesn't need to add extra status stage for test mode handling,
otherwise, the controller can't enter the test mode. Through the Lecroy
bus analyzer log, the controller will always wait status stage
even it is prepared by software later than the test mode is set
by software. If we comment out the status stage at cdns3_ep0_setup_phase,
the controller will not enter test mode even the test mode is set
beforehand.
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Assign interrupt number to USB gadget structure.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
And delete cdsn3_hw_role_state_machine declare which doesn't
be needed.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In short, we have three kinds of role switches:
- Based on SoC: ID and VBUS
- Based on external connnctor, eg, Type-C or GPIO Connector
- Based on user choices through sysfs
Since HW handling and usb-role-switch handling are at
different places, we do not need role_override any more,
and this flag could not judge external connector case well.
With role_override deleted, We use cdns3_hw_role_switch for
the 1st use case, and usb-role-switch for the 2nd and 3rd cases.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
After that, the role switch device (eg, Type-C device) could call
cdns3_role_set to finish the role switch.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mark all local functions static to fix sparse warnings.
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following sparse warning:
drivers/usb/cdns3/gadget.c:85:6: warning: symbol
'cdns3_clear_register_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:140:26: warning: symbol
'cdns3_next_align_buf' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:151:22: warning: symbol
'cdns3_next_priv_request' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:193:5: warning: symbol 'cdns3_ring_size' was
not declared. Should it be static?
drivers/usb/cdns3/gadget.c:348:6: warning: symbol
'cdns3_move_deq_to_next_trb' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:514:20: warning: symbol
'cdns3_wa2_gadget_giveback' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:554:5: warning: symbol
'cdns3_wa2_gadget_ep_queue' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:839:6: warning: symbol
'cdns3_wa1_restore_cycle_bit' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1907:6: warning: symbol
'cdns3_stream_ep_reconfig' was not declared. Should it be static?
drivers/usb/cdns3/gadget.c:1928:6: warning: symbol
'cdns3_configure_dmult' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200402123837.5850-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During device mode initialization, lots of device information
are printed to console, see below. Change them as debug message.
cdns-usb3 5b130000.cdns3: Initialized ep0 support:
cdns-usb3 5b130000.cdns3: Initialized ep1out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7out support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep1in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep2in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep3in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep4in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep5in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep6in support: BULK, INT ISO
cdns-usb3 5b130000.cdns3: Initialized ep7in support: BULK, INT ISO
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-4-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And delete cdsn3_hw_role_state_machine declare which doesn't
be needed.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In short, we have three kinds of role switches:
- Based on SoC: ID and VBUS
- Based on external connnctor, eg, Type-C or GPIO Connector
- Based on user choices through sysfs
Since HW handling and usb-role-switch handling are at
different places, we do not need role_override any more,
and this flag could not judge external connector case well.
With role_override deleted, We use cdns3_hw_role_switch for
the 1st use case, and usb-role-switch for the 2nd and 3rd cases.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After that, the role switch device (eg, Type-C device) could call
cdns3_role_set to finish the role switch.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200331081005.32752-1-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The signed 1 bit bitfields should be unsigned, so make them unsigned.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200325125041.94769-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB role callback functions had a parameter pointing to
the parent device (struct device) of the switch. The
assumption was that the switch parent is always the
controller. Firstly, that may not be true in every case, and
secondly, it prevents us from supporting devices that supply
multiple muxes.
Changing the first parameter of usb_role_switch_set_t and
usb_role_switch_get_t from struct device to struct
usb_role_switch.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.
To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has marked the dequeue trb as link trb, but its next segment
pointer is still itself, it causes the transfer can't go on. Fix
it by set its pointer as the trb address for the next request.
Fixes: f616c3bda4 ("usb: cdns3: Fix dequeue implementation")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer trb being assigned with a value that is never read, it is
assigned a new value later on. The assignment is redundant and
can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200208161802.28846-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The text contains a spelling mistake, "to" should be "too"
so fix this and re-work the grammar to make it more readable.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200122234437.2829803-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a Cadence USB3 core for imx8qm and imx8qxp SoCs, the cdns
core is the child for this glue layer device.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch includes streams implementation changes.
The current changes has been validated on FPGA platform.
Enabled streams related interrupts only for streams capable endpoints.
Processed PRIME and IOT interrupts related to streams capable endpoints.
Based on PRIME interrupt prime_flag is set and transfer is armed
otherwise just adding request to the deferred request queue.
For streams capable endpoints preparing TD with correct stream ID.
TDL calculation:
Updated tdl calculation based on controller versions.
1. For controller version DEV_VER_V2 :We have enabled USB_CONF2_EN_TDL_TRB
bit in usb_conf2 register in DMULT configuration.
This enables TDL calculation based on TRB, hence setting TDL in TRB.
2. For controller Version < DEV_VER_V2 : Writing TDL and STDL in ep_cmd
register
3. For controller version > DEV_VER_V2 : Writing TDL in ep_tdl register.
Writing ERDY with correct Stream ID to ep_cmd register.
Added stream id related information to trace logs.
Signed-off-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
-----BEGIN PGP SIGNATURE-----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=Xyc8
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.5
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
* tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (44 commits)
usb: dwc3: of-simple: add a shutdown
usb: cdns3: Add TI specific wrapper driver
dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
usb: mtu3: fix race condition about delayed_status
usb: gadget: Add UDC driver for tegra XUSB device mode controller
usb: dwc3: debug: Remove newline printout
usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
usb: gadget: udc: lpc32xx: Use devm_platform_ioremap_resource() in lpc32xx_udc_probe()
USB: gadget: udc: clean up an indentation issue
usb: gadget: Quieten gadget config message
phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irq
usb: gadget: Remove set but not used variable 'opts' in msg_do_config
usb: gadget: Remove set but not used variable 'opts' in acm_ms_do_config
usb: mtu3: add a new function to do status stage
usb: gadget: configfs: fix concurrent issue between composite APIs
usb: gadget: f_tcm: Provide support to get alternate setting in tcm function
usb: gadget: Correct NULL pointer checking in fsl gadget
usb: fsl: Remove unused variable
USB: dummy-hcd: use usb_urb_dir_in instead of usb_pipein
USB: dummy-hcd: increase max number of devices to 32
...
EP_CLAIMED flag is used to track the claimed endpoints. While unloading the
module, Reset EP_CLAIMED flag for all enabled endpoints. So that it can be
reused.
Signed-off-by: Sanket Parmar <sparmar@cadence.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20191029122441.5816-1-sparmar@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The J721e platform comes with 2 Cadence USB3 controller
instances. This driver supports the TI specific wrapper
on this platform.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB gadget core is supposed to manage pullups
of the controller. Don't manage pullups from within
the controller driver. Otherwise, function drivers
are not able to keep the controller disconnected from
the bus till they are ready. (e.g. g_webcam)
Reviewed-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The cdns3_host_init() function is declared in host-export.h
but host.c does not include it. Add the include to have
the declaration present (and remove the declaration of
cdns3_host_exit which is now static).
Fixes the following sparse warning:
drivers/usb/cdns3/host.c:58:5: warning: symbol 'cdns3_host_init' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB_DR_MODE_UNKNOWN should be treated as error as it is done in
cdns3_drd_update_mode().
Fixes: 02ffc26df9 ("usb: cdns3: fix cdns3_core_init_role()")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20191017075801.8734-1-rogerq@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dequeuing implementation in cdns3_gadget_ep_dequeue gets first request from
deferred_req_list and changed TRB associated with it to LINK TRB.
This approach is incorrect because deferred_req_list contains requests
that have not been placed on hardware RING. In this case driver should
just giveback this request to gadget driver.
The patch implements new approach that first checks where dequeuing
request is located and only when it's on Transfer Ring then changes TRB
associated with it to LINK TRB.
During processing completed transfers such LINK TRB will be ignored.
Reported-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1570958420-22196-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch restores the correct DMA mask after switching back to device
mode.
The issue occurred because Device part of controller use 32 bits DMA and
Host side use 64 bits DMA. During loading XHCI driver the DMA mask
used by driver is overwritten by XHCI driver so it must be restored
to 32 bits.
Reported-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/1570449803-15299-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At startup we should trigger the HW state machine
only if it is OTG mode. Otherwise we should just
start the respective role.
Initialize idle role by default. If we don't do this then
cdns3_idle_role_stop() is not called when switching to
host/device role and so lane switch mechanism
doesn't work. This results to super-speed device not working
in one orientation if it was plugged before driver probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Link: https://lore.kernel.org/r/20191007121601.25996-2-rogerq@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to disable USB3 PHY for full-speed mode else
gadget mode is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20191007121601.25996-3-rogerq@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fixes issue with Halt Endnpoint Test observed during using g_zero
driver as DUT. Bug occurred only on some testing board.
Endpoint can defer transition to Halted state if endpoint has pending
requests.
Patch add additional condition that allows to return correct endpoint
status during Get Endpoint Status request even if the halting endpoint
is in progress.
Reported-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Rahul Kumar <kurahul@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Tested-by: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/1570430355-26118-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fix issue in cdns3_ep0_feature_handle_device function.
The function usleep_range can't be used there because this function is
called with locks held and IRQs disabled in
cdns3_device_thread_irq_handler().
To resolve this issue patch replaces usleep_range with mdelay.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1569484721-4424-1-git-send-email-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't use "wrap" after it has been freed.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190904100102.GB7007@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20190903153625.85691-1-weiyongjun1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the check on a non-zero return code in ret is false because
ret has been initialized to zero. I believe that ret should be assigned
to the return from the call to readl_poll_timeout_atomic before the
check on ret. Since ret is being re-assinged the original initialization
of ret to zero can be removed.
Addresses-Coverity: ("'Constant' variable guards dead code")
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190902145035.18200-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case where an allocation fails for priv_ep ret is
assigned -ENOMEM and the code exits via the exit path 'err'.
The exit path returns -ENOMEM without using variable ret, so
the assingment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190902184334.27406-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/cdns3/gadget.c: In function '__cdns3_gadget_init':
drivers/usb/cdns3/gadget.c:2665:23: warning:
variable 'priv_dev' set but not used [-Wunused-but-set-variable]
drivers/usb/cdns3/gadget.c: In function cdns3_start_all_request:
drivers/usb/cdns3/gadget.c:357:24: warning:
variable priv_req set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190903120445.22204-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/usb/cdns3/ep0.c: In function cdns3_ep0_feature_handle_device:
drivers/usb/cdns3/ep0.c:290:6: warning: variable wIndex set but not used [-Wunused-but-set-variable]
drivers/usb/cdns3/ep0.c:289:6: warning: variable wValue set but not used [-Wunused-but-set-variable]
wIndex is never used, so remove it.
wValue should be use in the switch statement.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190903120615.19504-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Controller for OUT endpoints has shared on-chip buffers for all incoming
packets, including ep0out. It's FIFO buffer, so packets must be handled
by DMA in correct order. If the first packet in the buffer will not be
handled, then the following packets directed for other endpoints and
functions will be blocked.
Additionally the packets directed to one endpoint can block entire on-chip
buffers. In this case transfer to other endpoints also will blocked.
To resolve this issue after raising the descriptor missing interrupt
driver prepares internal usb_request object and use it to arm DMA
transfer.
The problematic situation was observed in case when endpoint has
been enabled but no usb_request were queued. Driver try detects
such endpoints and will use this workaround only for these endpoint.
Driver use limited number of buffer. This number can be set by macro
CDNS_WA2_NUM_BUFFERS.
Such blocking situation was observed on ACM gadget. For this function
host send OUT data packet but ACM function is not prepared for
this packet. It's cause that buffer placed in on chip memory block
transfer to other endpoints.
Issue has been fixed for DEV_VER_V2 version of controller.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch introduce new Cadence USBSS DRD driver to Linux kernel.
The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
