Simplify code and reduce object size by more than 300 bytes (x86_64).
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Turns out that TMP411B and TMP411C have different and unique device IDs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
TMP431 is compatible to TMP401.
Also add support for additional I2C addresses supported by TMP411B
and TMP411C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Initialize device specific coefficients from table instead of hard-coding it
to simplify adding additional chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Limits on all supported sensors and chips have to be within 0..0x0fff,
and limits are always positive.
Clamp written values in chip driver. Also clear value cache to ensure
that the actually written value is read back and reported correctly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the driver reported the voltage on VAUX as "vout2". This was not
entirely appropriate as it is not an output voltage, and complicates
the code. Use the new virtual "VMON" register set and report the voltage
as "vmon" instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify the code and reduce its size by using is_visible to determine
valid attributes, and sysfs_create_group to create all of them with
a single call.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use u16 instead of int to store cached limit attributes.
This reduces allocated data size per driver instance by 48 bytes.
Use defines for the number of pages supported by individual chips.
Use ARRAY_SIZE for loops to initialize array variables, and
initialize all variables in the same code block.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix:
ERROR: Macros with complex values should be enclosed in parenthesis
by unwinding the problematic macros.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix:
ERROR: Macros with complex values should be enclosed in parenthesis
by unwinding the problematic macros.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix:
ERROR: Macros with complex values should be enclosed in parenthesis
by unwinding the problematic macros.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The read/write lock is acquired for each read/write operation from/to the chip.
This occurs either during initialization, when it is not needed, or during
updates, when the update_lock is held as well, and it is not needed either.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Scan all temperature sources used for fan control and report if additional
monitoring registers are available.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT677X series support weighted fan control. In this mode, a secondary
temperature source is used in addition to the primary temperature source to
control fan speed. Add support for this feature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver will replace the w83627ehf driver for NCT6775F and NCT6776F,
and provides support for NCT6779D.
This patch provides support for voltage monitor attributes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix:
ERROR: Macros with complex values should be enclosed in parenthesis
when it is seen due to complex code and not due to multi-line variable
declarations.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds DT support to NTC driver to parse the
platform data.
Also adds the support to work as an iio device client.
During the probe ntc driver gets the respective channels of ADC
and uses iio_raw_read calls to get the ADC converted value.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[Guenter Roeck: fixed Kconfig dependencies; use ERR_CAST]
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This allows an userspace application to poll() on the alarm files to get
notified in case of a temperature threshold event.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7310/adt7320 is the SPI version of the adt7410/adt7420. The register map
layout is a bit different, i.e. the register addresses differ between the two
variants, but the bit layouts of the individual registers are identical. So both
chip variants can easily be supported by the same driver. The issue of non
matching register address layouts is solved by a simple look-up table which
translates the I2C addresses to the SPI addresses.
The patch moves the bulk of the adt7410 driver to a common module that will be
shared by the adt7410 and adt7310 drivers. This common module implements the
driver logic and uses a set of virtual functions to perform IO access. The
adt7410 and adt7310 driver modules provide proper implementations of these IO
accessor functions for I2C respective SPI.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently each time the temperature register is read the driver also reads the
threshold and hysteresis registers. This increases the amount of I2C traffic and
time needed to read the temperature by a factor of ~5. Neither the threshold nor
the hysteresis change on their own, so once we have read them, we should be able
to just use the cached value of the registers. This patch modifies the code
accordingly and only reads the threshold and hysteresis registers once during
probe.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
New stuff
1) Add OF support for specifying mappings between iio devices and their
in kernel consumers.
2) Driver for AD7923 (extra functionality and support for ad7904, ad7914 and
ad7924 added later in series)
3) Driver for Exynos adc (dt suppor for phy added later in series).
4) Make iio_push_event save IRQ context - necessary if it is to be used
within an interrupt handler. Users of this functionality to follow.
5) For iio use the device tree node name to provide the hwmon name attribute
if available.
Removal and moves out of staging
1) Drop the adt7410 driver from IIO now that there is a hmwon driver with
equivalent support. This device is very much targeted at hardware
monitoring so hwmon is a more appropriate host for the driver.
2) Move iio_hwmon driver to drivers/hwmon.
Cleanups
1) Minor cleanup in ST common library.
2) Large set of patches to break the info_mask element which previously used
odd and even bits to specify if a channel attribute was either shared across
similar channels or specific to only one. Now we have two bitmaps, one for
those parameters that are specific to this channel and one for those shared
by all channels with the same type as this one. This has no effect on the
userspace abi. It simplifies the core code and provides more space for new
channel parameters. It has been on the todo list for a long time!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=99m9
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.10a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of IIO new drivers and cleanup for the 3.10 cycle.
New stuff
1) Add OF support for specifying mappings between iio devices and their
in kernel consumers.
2) Driver for AD7923 (extra functionality and support for ad7904, ad7914 and
ad7924 added later in series)
3) Driver for Exynos adc (dt suppor for phy added later in series).
4) Make iio_push_event save IRQ context - necessary if it is to be used
within an interrupt handler. Users of this functionality to follow.
5) For iio use the device tree node name to provide the hwmon name attribute
if available.
Removal and moves out of staging
1) Drop the adt7410 driver from IIO now that there is a hmwon driver with
equivalent support. This device is very much targeted at hardware
monitoring so hwmon is a more appropriate host for the driver.
2) Move iio_hwmon driver to drivers/hwmon.
Cleanups
1) Minor cleanup in ST common library.
2) Large set of patches to break the info_mask element which previously used
odd and even bits to specify if a channel attribute was either shared across
similar channels or specific to only one. Now we have two bitmaps, one for
those parameters that are specific to this channel and one for those shared
by all channels with the same type as this one. This has no effect on the
userspace abi. It simplifies the core code and provides more space for new
channel parameters. It has been on the todo list for a long time!
Conflicts:
drivers/iio/dac/ad5064.c
This driver uses channel maps, defined either through device tree
or platform data, to create a hwmon driver which acts as a client
for the underlying IIO device channels. Thus a general purpose
IIO adc driver can be used to provide hardware monitoring using a subset
of its channels.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
--
The only non move changes here concern the description and changes to the
dependencies to IIO explicit and hwmon implicit.
I'm proposing moving this into hwmon on the basis of placing drivers
based on what they provide rather than what their underlying hardware
is.
drivers/hwmon/Kconfig | 9 ++
drivers/hwmon/Makefile | 1 +
drivers/hwmon/iio_hwmon.c | 196 ++++++++++++++++++++++++++++++++++++++++
drivers/staging/iio/Kconfig | 8 --
drivers/staging/iio/Makefile | 2 -
drivers/staging/iio/iio_hwmon.c | 196 ----------------------------------------
6 files changed, 206 insertions(+), 206 deletions(-)
File lm75.h used to include <linux/hwmon.h> for SENSORS_LIMIT() but
this function is gone by now. Instead we call clamp_val() so we should
include <linux/kernel.h>, where this function is declared.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
On LTC2978, only READ_TEMPERATURE is supported. It reports
the internal junction temperature. This register is unpaged.
On LTC3880, READ_TEMPERATURE and READ_TEMPERATURE2 are supported.
READ_TEMPERATURE is paged and reports external temperatures.
READ_TEMPERATURE2 is unpaged and reports the internal junction
temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
If krealloc() returns NULL, it *doesn't* free the original. So any code
of the form 'foo = krealloc(foo, …);' is almost certainly a bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not having power is a pretty serious error so check that we are able to
enable the supply and error out if we can't.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org #3.8+; 3.0+ will need manual backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We read the chip ID from the chip, use it to determine if the chip ID provided
to the driver is correct, and report it if wrong. We should also use the
correct chip ID to select supported functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
Peak attributes were not initialized and cleared correctly.
Also, temp2_max is only supported on page 0 and thus does not need to be
an array.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from
Rafael J. Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng
with contributions from Aaron Lu, Chao Guan, Jesper Juhl, and
Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri
with contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from
Dirk Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King,
Davidlohr Bueso, Joseph Salisbury, Kees Cook, Li Fei,
Nishanth Menon, ShuoX Liu, Srinivas Pandruvada, Tejun Heo,
Thomas Renninger, and Yasuaki Ishimatsu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=wijn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Rework of the ACPI namespace scanning code from Rafael J. Wysocki
with contributions from Bjorn Helgaas, Jiang Liu, Mika Westerberg,
Toshi Kani, and Yinghai Lu.
- ACPI power resources handling and ACPI device PM update from Rafael
J Wysocki.
- ACPICA update to version 20130117 from Bob Moore and Lv Zheng with
contributions from Aaron Lu, Chao Guan, Jesper Juhl, and Tim Gardner.
- Support for Intel Lynxpoint LPSS from Mika Westerberg.
- cpuidle update from Len Brown including Intel Haswell support, C1
state for intel_idle, removal of global pm_idle.
- cpuidle fixes and cleanups from Daniel Lezcano.
- cpufreq fixes and cleanups from Viresh Kumar and Fabio Baltieri with
contributions from Stratos Karafotis and Rickard Andersson.
- Intel P-states driver for Sandy Bridge processors from Dirk
Brandewie.
- cpufreq driver for Marvell Kirkwood SoCs from Andrew Lunn.
- cpufreq fixes related to ordering issues between acpi-cpufreq and
powernow-k8 from Borislav Petkov and Matthew Garrett.
- cpufreq support for Calxeda Highbank processors from Mark Langsdorf
and Rob Herring.
- cpufreq driver for the Freescale i.MX6Q SoC and cpufreq-cpu0 update
from Shawn Guo.
- cpufreq Exynos fixes and cleanups from Jonghwan Choi, Sachin Kamat,
and Inderpal Singh.
- Support for "lightweight suspend" from Zhang Rui.
- Removal of the deprecated power trace API from Paul Gortmaker.
- Assorted updates from Andreas Fleig, Colin Ian King, Davidlohr Bueso,
Joseph Salisbury, Kees Cook, Li Fei, Nishanth Menon, ShuoX Liu,
Srinivas Pandruvada, Tejun Heo, Thomas Renninger, and Yasuaki
Ishimatsu.
* tag 'pm+acpi-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (267 commits)
PM idle: remove global declaration of pm_idle
unicore32 idle: delete stray pm_idle comment
openrisc idle: delete pm_idle
mn10300 idle: delete pm_idle
microblaze idle: delete pm_idle
m32r idle: delete pm_idle, and other dead idle code
ia64 idle: delete pm_idle
cris idle: delete idle and pm_idle
ARM64 idle: delete pm_idle
ARM idle: delete pm_idle
blackfin idle: delete pm_idle
sparc idle: rename pm_idle to sparc_idle
sh idle: rename global pm_idle to static sh_idle
x86 idle: rename global pm_idle to static x86_idle
APM idle: register apm_cpu_idle via cpuidle
cpufreq / intel_pstate: Add kernel command line option disable intel_pstate.
cpufreq / intel_pstate: Change to disallow module build
tools/power turbostat: display SMI count by default
intel_idle: export both C1 and C1E
ACPI / hotplug: Fix concurrency issues and memory leaks
...
All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Zlkx
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree changes from Grant Likely:
"All around device tree changes destined for v3.8. Aside from the
documentation updates the highlights in this branch include:
- Kbuild changes for using CPP with .dts files
- locking fix from preempt_rt patchset
- include DT alias names in device uevent
- Selftest bugfixes and improvements
- New function for counting phandles stanzas in a property
- constify argument to of_node_full_name()
- Various bug fixes
This tree did also contain a commit to use platform_device_add instead
of open-coding the device add code, but it caused problems with amba
devices and needed to be reverted."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (23 commits)
Revert "of: use platform_device_add"
kbuild: limit dtc+cpp include path
gpio: Make of_count_named_gpios() use new of_count_phandle_with_args()
of: Create function for counting number of phandles in a property
of/base: Clean up exit paths for of_parse_phandle_with_args()
of/selftest: Use selftest() macro throughout
of/selftest: Fix GPIOs selftest to cover the 7th case
of: fix recursive locking in of_get_next_available_child()
documentation/devicetree: Fix a typo in exynos-dw-mshc.txt
OF: convert devtree lock from rw_lock to raw spinlock
of/exynos_g2d: Add Bindings for exynos G2D driver
kbuild: create a rule to run the pre-processor on *.dts files
input: Extend matrix-keypad device tree binding
devicetree: Move NS2 LEDs binding into LEDs directory
of: use platform_device_add
powerpc/5200: Fix size to request_mem_region() call
documentation/devicetree: Fix typos
of: add 'const' to of_node_full_name parameter
of: Output devicetree alias names in uevent
DT: add vendor prefixes for Renesas and Toshiba
...
Fixes the following sparse warnings:
drivers/hwmon/ntc_thermistor.c:46:31: warning:
symbol 'ncpXXwb473' was not declared. Should it be static?
drivers/hwmon/ntc_thermistor.c:82:31: warning:
symbol 'ncpXXwl333' was not declared. Should it be static?
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7420 is software compatible to the adt7410.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the I2C_ADDRS macro to initialize the I2C device's address_list. Doing so
saves a few lines of boilerplate code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Only build the suspend/resume code if CONFIG_PM_SLEEP is selected. Currently the
code is built if CONFIG_PM is selected, but it will also be selected if only
runtime PM support is built into the kernel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make sure to clear the mode bits from the config register before setting the new
mode. Otherwise we might end up with a different mode than we want to.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch replaces the horribly coded of_count_named_gpios() with a
call to of_count_phandle_with_args() which is far more efficient. This
also changes the return value of of_gpio_count() & of_gpio_named_count()
from 'unsigned int' to 'int' so that it can return an error code. All
the users of that function are fixed up to correctly handle a negative
return value.
v2: Split GPIO portion into a separate patch
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Rearranged some data structures, and merged some common functions.
Overall code and data size reduction by more than 900 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX34460 is a PMBus 12-Channel Voltage Monitor & Sequencer.
MAX34461 is a PMBus 16-Channel Voltage Monitor & Sequencer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not all PMBus devices support the byte status register at 0x78.
Try to use the word status register at 0x79 instead if that is the case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the ZL6100 compatible chips support monitoring a separate voltage pin,
VMON (ZL2004) or VDRV (ZL91xx). Report it as in2 / vmon.
The chips support implicit warning limits for VMON/VDRV, as percentage of the
respective critical voltage. Support by reading/writing the critical voltages
and calculating the associated warning voltages.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For PMBus chips, modifying one limit register may affect other limits.
Since limits are all cached in the PMBus core driver, related changes
are not reflected in reported limits.
Introduce function to clear the attribute cache. After calling this function,
the core pmbus driver re-reads all cached values.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips support monitoring an additional non-standard voltage. While
this voltage can in many cases be supported by simulating an additional sensor
page, this does not work in all cases. Specifically, it is problematic if the
data format is linear and the voltage is reported in LINEAR11 format. Since
output voltages use LINEAR16, and the exponent for LINEAR16 data is chip-wide
and fixed, this can result in overflows.
To solve this problem, add support for an additional virtual input voltage,
call it 'vmon', and treat this voltage as input voltage (which, when the chip
supports linear data format, uses LINEAR11).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far, attribute memory was allocated by pre-calculating the maximum possible
amount of attributes. Not only does this waste memory, it is also risky because
the calculation might be wrong. It also requires a lot of defines to specify
the maximum number of attributes per class.
Allocate attribute memory using krealloc() instead. That means we have to use
kfree(), since devm_krealloc() does not exist, but that is still less costly
and less risky than trying to predict the number of attributes at the beginning.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since memory is now allocated with dev_ functions, we no longer need to keep
track of allocated memory. Sensor memory allocation can therefore be
simplified significantly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boolean handling depends on storing the sensor data index in sensor_device_attr
as part of the index variable. This limits the number of sensor attributes to
256, and means the sensor sequence number actually has to be maintained to be
able to access sensor data from boolean functions.
Rework the code to store sensor pointers in the pmbus_boolean data structure
directly. With this approach, the number of supportable sensors is now
unlimited.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since memory is now allocated with dev_ functions, we no longer need to keep
track of allocated memory. Memory allocation for booleans and labels can
therefore be simplified substantially by allocating it only as needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
by unwinding the problematic macros.
As a side effect, this patch reduces code size on x86_64 by 160 bytes and bss
size by 64 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for temp1_min_alarm and temp1_max_alarm
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup; dropped platform data and interrupt support]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM73 supports four A/D conversion resolutions. The default used by
the existing lm73 driver is the chip's default, 11-bit (0.25 C/LSB).
This patch enables changing of this resolution from userspace via the
update_interval sysfs attribute. Full details on usage are included in
Documentation/hwmon/lm73.
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While the LM73 is only specified for temperatures from -40 to +150 degrees C,
its power-up minimum and maximum temperature limits are -256 and +255.75
degrees C. For better consistency and to avoid confusion, clamp limits to
the power-up limits and not to -40 / +150 degrees C.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assume that IT8771E and IT8772E are fully compatible with IT8728F.
IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Without this patch, the SHT15 driver may fail silently with a
non-bidirectional data line and/or an input-only clock line.
This patch checks the return value of gpio_direction_* function calls
and returns the error code (if any) to the caller. If an error occurs in
the read work function (work_funct_t), we wake the queue up directly
without updating the data->state flag, to notice the waiter of the I/O
error.
The patch also makes minor cleanups: s/error_ret/unlock for some labels
and uses devm_gpio_request_one() for the clock line.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SENSORS_LIMIT and the generic clamp_val have the same functionality,
and clamp_val is more efficient.
This patch reduces text size by 9052 bytes and bss size by 11624 bytes
for x86_64 builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch renames the supply_uV* variables to supply_uv* to avoid
CamelCase as warned by the checkpatch.pl script.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The second argument of ACPI driver .remove() operation is only used
by the ACPI processor driver and the value passed to that driver
through it is always available from the given struct acpi_device
object's removal_type field. For this reason, the second ACPI driver
.remove() argument is in fact useless, so drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Fix:
vexpress.c: In function ‘vexpress_hwmon_name_show’:
vexpress.c:34:2: error: implicit declaration of function
‘of_get_property’ [-Werror=implicit-function-declaration]
vexpress.c:34:27: warning: initialization makes pointer from integer
without a cast [enabled by default]
vexpress.c: In function ‘vexpress_hwmon_label_show’:
vexpress.c:43:22: warning: initialization makes pointer from integer
without a cast [enabled by default]
Seen if CONFIG_OF_DEVICE is not defined. of_get_property is declared in
of.h which is only included by of_device.h if CONFIG_OF_DEVICE is defined.
of.h needs to be included directly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Result of DIV_ROUND_CLOSEST is undefined for negative dividends if the divisor
variable type is unsigned. Fix by declaring divisor as signed variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
If an LM73 device does not exist on an I2C bus, attempts to communicate
with the device result in an error code returned from the i2c read/write
functions. The current lm73 driver casts that return value from a s32
type to a s16 type, then converts it to a temperature in celsius.
Because negative temperatures are valid, it is difficult to distinguish
between an error code printed to the response buffer and a negative
temperature recorded by the sensor.
The solution is to evaluate the return value from the i2c functions
before performing any temperature calculations. If the i2c function did
not succeed, the error code should be passed back through the virtual
file system layer instead of being printed into the response buffer.
Before:
$ cat /sys/class/hwmon/hwmon0/device/temp1_input
-46
After:
$ cat /sys/class/hwmon/hwmon0/device/temp1_input
cat: read error: No such device or address
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since family 11h processors, AMD is exclusively using 7-bit VID codes
transmitted using a serial protocol over two pins (clock and data.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: David Hubbard <david.c.hubbard@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Extend support for reporting and selecting PECI temperature sensors
to IT8718, IT8720, IT8782, and IT8783. For IT8721, report the sensor
type for temp2 as Intel PECI (6) if the chip is configured to report
the PCH temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
IT8721 and IT8728 support Intel PECI temperature reporting. Each sensor
can be programmed to display the temperature reported on the PECI interface.
If configured for Intel PECI, the driver reported the wrong sensor type for
the respective thermal sensor. Fix the code to correctly report it as
"Intel PECI (6)".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This simplifies the code, improves runtime performance, reduces
code size (about 280 bytes on x86_64), and makes it easier
to add support for new devices.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix checkpatch error:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Also unify fan functions to use the same code for 8 and 16 bit fans.
This patch reduces code size by approximately 1,200 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The macro name show_sensor_offset is confusing since it related to the sensor
type, not an offset - even more so when we introduce offset attributes later on.
Replace it with direct definitions, and replace the show_sensor/set_sensor
function names with show_temp_type/set_temp_type. This also resolves a
checkpatch error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reduces code size (more than 600 bytes on x86_64),
and gets rid of some checkpatch errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cleaner code, fewer checkpatch errors, and reduced code size
(saves more than 500 bytes on x86-64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The smatch static code analyzer complains:
drivers/hwmon/w83627ehf.c:911 w83627ehf_update_device() error: buffer overflow 'W83627EHF_REG_TEMP_OFFSET' 3 <= 8
drivers/hwmon/w83627ehf.c:909 w83627ehf_update_device() error: buffer overflow 'data->temp_offset' 3 <= 8
drivers/hwmon/w83627ehf.c:2672 w83627ehf_resume() error: buffer overflow 'W83627EHF_REG_TEMP_OFFSET' 3 <= 8
drivers/hwmon/w83627ehf.c:2673 w83627ehf_resume() error: buffer overflow 'data->temp_offset' 3 <= 8
A deeper analysis of the code shows that these are false positives, as
only the lower 3 bits of data->have_temp_offset can be set so the
write is never attempted with i >= 3. However this shows that the code
isn't very robust and future changes could easily introduce a buffer
overflow. So let's add a safety check to prevent that and make smatch
happy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <PeterHuewe@gmx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Only the W83627HF could be accessed through I2C. All other supported
chips are LPC-only, so they do not have I2C address registers. Don't
write to nonexistent or reserved registers on these chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
On suspend some register values are lost, most notably the Value RAM
areas but also other limits and settings. Restore them on resume.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
On suspend some register values are lost, most notably the Value RAM
areas but also other limits. Restore them on resume. On top of that,
some fixups are needed to work around BIOS bugs, in particular when
the BIOS omits running the same initialization sequence on resume
that it does after boot. In that case we have to carry initialization
over suspend.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Thankfully this only affects systems with one specific south bridge
and is most probably harmless unless the hwmon module is heavily
cycled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Commit 281dfd0 removed __devexit from the exit function but left __exit_p in
place. This results in the following warning message if the module is built into
the kernel.
twl4030-madc-hwmon.c:123:12: warning: ‘twl4030_madc_hwmon_remove’ defined
but not used [-Wunused-function]
Fix by removing __exit_p as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This is
going to be a pain for the merge with different subsystem trees, I know,
but all of the patches included here have been ACKed by their various
subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them all,
it's up to you. The merges should all be trivial, and Stephen has been
doing them all in linux-next for a few weeks now quite easily.
Other than the __dev* marking removals, there's nothing major here, some
firmware loading updates and other minor things in the driver core.
All of these have (much to Stephen's annoyance), been in linux-next for
a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHkPkACgkQMUfUDdst+ykaWgCfW7AM30cv0nzoVO08ax6KjlG1
KVYAn3z/KYazvp4B6LMvrW9y0G34Wmad
=yvVr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
Set chan_mux[DA9055_ADC_ADCIN3] = DA9055_ADC_MUX_ADCIN3.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since N4xx, N5xx, D4xx, and D5xx are now reliably detected using the model ID
and the stepping/mask, drop the respective entries from tjmax_table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Make the code easier to extend and easier to adjust by using a model table
listing CPU models, stepping/mask, and associated TjMax.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).
Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.
Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.
ID Stepping TjMax Models
0x1c 10 100 D4xx, N4xx, D5xx, N5xx
0x1c not 10 90 Z5xx, N2xx, 230, 330, others
0x26 - 90 Atom Tunnel Creek (Exx),
Lincroft (Z6xx)
0x27 - 90 Atom Medfield (Z2460)
0x36 - 100 Atom Cedar Trail (N2xxx, D2xxx)
Also drop the module dependency on PCI.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add family 16h PCI ID to AMD's power driver to allow it report
power consumption on these processors.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These got broken by recent patches fixing checkpatch warnings in these
drivers. The trick is that the patches themselves looked good, but the
source files after applying them do not. That's why I am not a big fan
of using tabs inside comments.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Don't assume bank 0 is selected at device probe time. This may not be
the case. Force bank selection at first register access to guarantee
that we read the right registers upon driver loading.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Guenter Roeck <linux@roeck-us.net>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
These drivers use no sleep or delay functions so they don't need to
include <linux/delay.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Rudolf Marek <r.marek@assembler.cz>
These drivers use IS_ERR so they should include <linux/err.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
Many hwmon drivers use jiffies but omit the inclusion of the header
file. Fix that, and also fix one driver which was including the header
file but didn't need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Conflicts:
drivers/staging/omap-thermal/omap-thermal-common.
OMAP supplied dummy TC1 and TC2,
at the same time that the thermal tree removed them
from thermal_zone_device_register()
drivers/thermal/cpu_cooling.c b/drivers/thermal/cpu_cooling.c
propogate the upstream MAX_IDR_LEVEL re-name
to prevent a build failure
Previously-fixed-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Len Brown <len.brown@intel.com>
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
This movement is needed because the hwmon entries and corresponding sysfs
interface is a duplicate of utilities already provided by
driver/thermal/thermal_sys.c. The goal is to place it in thermal folder
and add necessary functions to use the in-kernel thermal interfaces.
Signed-off-by: Amit Daniel Kachhap <amit.kachhap@linaro.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: SangWook Ju <sw.ju@samsung.com>
Cc: Durgadoss <durgadoss.r@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This Patch adds support for mcp3221 chip to the
mcp3021 driver.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This Patch is to prepare the MCP3021 driver to support
other chips like the MCP3221. The hard defined chip data
is now stored within the data struct of each chip.
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following build warnings are seen with -Wextra.
w83791d.c: In function store_temp_target:
w83791d.c:858:2: warning: comparison of unsigned expression < 0 is always false
w83791d.c: In function store_temp_tolerance:
w83791d.c:920:2: warning: comparison of unsigned expression < 0 is always false
For store_temp_target, accept negative numbers and clamp to >= 0.
For store_temp_tolerance, drop the unnecessary comparison.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
The following build warning is seen with -Wextra.
lm93.c: In function ‘store_fan_smart_tach’:
lm93.c:1833:2: warning: comparison of unsigned expression >= 0 is always true
Drop the unnecessary comparison.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Instead of using a switch statement to determine the device name, use
to_spi_device(dev)->modalias to simplify the code and reduce module size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Display device name using to_spi_device(dev)->modalias instead of computing it
from the number of ADC channels. This is cleaner and reduces code size.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CONFIG_EXPERIMENTAL is expected to be removed, so drop dependencies on it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add missing reference to IT8782F and IT8783E/F to it87 driver description
in Kconfig. Replace wrong reference to Si960 with the correct Si950.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch moves the sht15.h header from include/linux to
include/linux/platform_data, and update existing support (stargate2
platform) accordingly.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA220 is register compatible to INA219, and INA230 is register compatible to
INA226, so all we need to do is to add name aliases for those two chips.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Replace per-device initialization and per-device calculation code with
per-device configuration data, which is then used to configure the chip and
perform calculations based on that data.
This patch reduces code size by more than 400 bytes on x86_64.
Cc: Lothar Felten <l-felten@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
MAX1110 is similar to MAX1111, with 8 instead of 4 channels. MAX1112 and MAX1113
are similar to MAX1110 and MAX1111, with 4.096V reference voltage instead of
2.048V.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add support for LM74 and LM71 to LM70 driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Removing the 3wire limitation on LM70 as the component also allows
operation on 4wire SPI bus
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declare an array of platform_device_id, instead of registering a driver
for each supported chip. This makes the code cleaner.
Also add a module description.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MAX197 is an A/D converter, made by Maxim. This driver currently
supports the MAX197, and MAX199. They are both 8-Channel, Multi-Range,
5V, 12-Bit DAS with 8+4 Bus Interface and Fault Protection.
The available ranges for the MAX197 are {0,-5V} to 5V, and {0,-10V} to
10V, while they are {0,-2V} to 2V, and {0,-4V} to 4V on the MAX199.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch brings basic support for the Analog Devices ADT7410 temperature
sensor. The following functionality has been implemented:
* get current temperature
* get/set minimum, maximum and critical temperature
* get/set hysteresis
* get alarm events for minimum, maximum and critical temperature
All implemented sysfs attributes have been sucessfully tested at temperatures
of 15°C to 40°C.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Urs Fleisch <urs.fleisch@sensirion.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Mingkai Hu <Mingkai.hu@freescale.com>
Cc: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert to use devm_ functions to reduce code size and simplify the code.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
