The powerpc kernel maintains information about logical memory blocks
in the lmb.memory structure, which is initialized and updated at boot
time, but not when memory is added or removed while the kernel is
running.
This adds a hotplug memory notifier which updates lmb.memory when
memory is added or removed. This information is useful for eHEA
driver to find out the memory layout and holes.
NOTE: No special locking is needed for lmb_add() and lmb_remove().
Calls to these are serialized by caller. (pSeries_reconfig_chain).
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Hotplug memory remove notifier for 64-bit powerpc. This gets invoked
by writing to /proc/ppc64/ofdt the string "remove_node " followed by
the firmware device tree pathname of the node that needs to be removed.
In response, this adjusts the sections and removes sysfs entries by
calling __remove_pages(). Then it calls arch-specific code to get rid
of the hardware MMU mappings for the section of memory.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Reviewed-by: Michael Ellerman <michael@ellerman.id.au>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kamalesh Babulal (kamalesh@linux.vnet.ibm.com) reports that CONFIG_NVRAM=m
is valid in terms of Kconfig but fails to build with:
Building modules, stage 2.
MODPOST 1401 modules
ERROR: "pmac_newworld" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
ERROR: "__alloc_bootmem" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
make[1]: *** [__modpost] Error
The arch/powerpc/platforms/powermac/nvram.c code really needs to be
builtin, but as its compilation is dependent on a generic Kconfig
symbol we force nvram.c to be builtin if CONFIG_NVRAM is 'y' or 'm'.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device. This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Add platform code to support Freescale DIU. The platform code includes
framebuffer memory allocation, pixel format, monitor port, etc.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for PCI Express port on Celleb. I/O space of this
PCI Express port is not mapped in memory space. So we use the
io-workaround mechanism to make accesses indirect.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves miscellaneous files for Beat into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves SPU support code on Beat into platforms/cell/.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves files for mmu and iommu on Beat into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves files for Beat hvcall interfaces into platforms/cell/.
All files in this patch are used by celleb-beat only.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the SCC (Super Companion Chip) related code for celleb
into platforms/cell/.
All files in this patch are used by celleb-beat and celleb-native
commonly.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the base code for celleb support into platforms/cell/.
All files in this patch are used by celleb-beat and celleb-native
commonly.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now, we can use generic io-workarounds mechanism and the workaround
code for spider-pci. This changes Celleb PCI code to use spider-pci
code.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits cell io-workaround code into spider-pci dependent code and
a generic part, and also moves io-workarounds initialization into
cell_setup_phb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a DEBUG config setting which turns on all (most) of the debugging
under platforms/pseries.
To have this take effect we need to remove all the #undef DEBUG's, in
various files. We leave the #undef DEBUG in platforms/pseries/lpar.c,
as this enables debugging printks from the low-level hash table routines,
and tends to make your system unusable. If you want those enabled you
still have to turn them on by hand.
Also some of the RAS code has a DEBUG block which causes a functional
change, so I've keyed this off a different (non-existant) debug #define.
This is only enabled if you have PPC_EARLY_DEBUG enabled also.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In pseries/lpar.c, fix some printf specifier mismatches, and add
a newline to one printk.
In pseries/rtasd.c add "rtasd" to some messages to make it clear
where they're coming from.
In pseries/scanlog.c remove the hand-rolled runtime debugging support
in there. This file has been largely unchanged for eons, if we need to
debug it in future we can recompile.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On pseries LPAR we can call the udbg routines, and the udbg console very
early. So mark the udbg console as safe to call early in boot, and register
the udbg console as soon as the udbg routines are hooked up.
This allows platforms/pseries code to use printk() and pr_debug() rather
than needing to call udbg_printf() directly for early debugging. This is
nice because a) it's standard, b) it goes via the printk buffer, and c)
you can get printk time stamps.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the required functionality to fill in all pacas at runtime.
With NR_CPUS=1024
text data bss dec hex filename
137 1704032 0 1704169 1a00e9 arch/powerpc/kernel/paca.o :Before
121 1179744 524288 1704153 1a00d9 arch/powerpc/kernel/paca.o :After
Also remove unneeded #includes from arch/powerpc/kernel/paca.c
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently all iSeries secondary CPUs spin directly on the cpu_start
field in their paca. Make them spin on the global
__secondary_hold_spinloop until after the pacas have been initialised.
As Stephen Rothwell points out, this works at the moment because
__secondary_hold_spinloop is being set already, but iSeries isn't
looking at it :)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace two open-coded occurences of the of_get_next_parent() logic.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
os-area.c requires routines declared in linux/of.h, so should include it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.26: (1090 commits)
[NET]: Fix and allocate less memory for ->priv'less netdevices
[IPV6]: Fix dangling references on error in fib6_add().
[NETLABEL]: Fix NULL deref in netlbl_unlabel_staticlist_gen() if ifindex not found
[PKT_SCHED]: Fix datalen check in tcf_simp_init().
[INET]: Uninline the __inet_inherit_port call.
[INET]: Drop the inet_inherit_port() call.
SCTP: Initialize partial_bytes_acked to 0, when all of the data is acked.
[netdrvr] forcedeth: internal simplifications; changelog removal
phylib: factor out get_phy_id from within get_phy_device
PHY: add BCM5464 support to broadcom PHY driver
cxgb3: Fix __must_check warning with dev_dbg.
tc35815: Statistics cleanup
natsemi: fix MMIO for PPC 44x platforms
[TIPC]: Cleanup of TIPC reference table code
[TIPC]: Optimized initialization of TIPC reference table
[TIPC]: Remove inlining of reference table locking routines
e1000: convert uint16_t style integers to u16
ixgb: convert uint16_t style integers to u16
sb1000.c: make const arrays static
sb1000.c: stop inlining largish static functions
...
The xics code currently has a direct and lpar variant of
xics_host_map, the only difference being which irq_chip they use. If
we remember which irq_chip we're using we can combine these two
routines. That also allows us to have a single irq_host_ops instead
of two.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pseries_mpic_init_IRQ() implements the same logic as the xics code did to
find the i8259 cascade irq. Now that we've pulled that logic out into
pseries_setup_i8259_cascade() we can use it in the mpic code.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the xics references from xics_setup_8259_cascade(), and merge the
good bits from the almost identical logic in pseries_mpic_init_IRQ().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The code in xics.c to setup the i8259 cascaded irq handler is not really
xics specific, so move it into setup.c - we will clean this up further in
a subsequent patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
IDE PMAC host driver and all IDE PCI host drivers use pci_enable_device()
nowadays so the following quirk in pmac_pcibios_after_init() can be removed.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add pmac_ide_init_ports() helper and use it instead of
pmac_ide_init_hwif_ports().
* Remove ppc_ide_md hooks - no need for them
(IDE pmac host driver takes care of all this setup).
* Then remove no longer needed <linux/ide.h> include
from arch/powerpc/platforms/powermac/pmac.h.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently USB Host isn't functional on the MPC8315E boards, for two
reasons as described below.
MPC8315 Reference Manual says:
"The USB DR unit must have the same clock ratio as the encryption core
unit, unless one of them has its clock disabled."
The encryption core also drives I2C clock, so it is enabled and is equal
to 01. That means USBDRCM should be 01 here.
Plus, according to MPC8315E-RDB schematics, USB unit consumes CLK_IN
clock from the 24.00MHz oscillator, which means we must adjust REFSEL
bits as well.
p.s.
Idially we should rework whole 83xx/usb.c code, in two steps:
1. Move SCCR code to the U-Boot;
2. Implement fsl,usb-clock property in the device tree, so usb.c could
decide what clock exactly to use on per-board basis.
Though, today we're not in a hurry since there is just one 8315e board
out there.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As suggested by Timur Tabi, we match on the old compat node ID for one
version and warn accordingly. If we don't do this, we plunge people who
try to use an old DTB into silent boot death with no clear indication of
what the problem is.
This patch should be removed at the beginning of the 2.6.27 dev cycle.
It is only meant to ease the transition in the short term.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleanups as suggested by Stephen Rothwell and Dale Farnsworth, which
incudes marking a bunch of functions static and add a vendor prefix to
the compat node check for uniqueness.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
arch/powerpc/platforms/85xx/mpc85xx_ads.c: In function ‘init_ioports’:
arch/powerpc/platforms/85xx/mpc85xx_ads.c:168: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds support for the Wind River SBC8641D board, based
largely on the mpc86xx_hpcn support. The biggest difference is
the lack of the Uli and the i8259 cascade, which simplifies things.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to probe nor and nand flashes on the localbus.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the device tree node for the DMA engine on 8544, publish
the device and enable the driver in the defconfig.
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Having the id field be an int was making more complex bus topologies
excessively difficult. For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There is logic in platforms/peries/lpars.c which checks if the user has
specified a console on the command line, and refrains from adding a
preferred console entry for the hvc/hvsi console if they have.
This trips up if you use "netconsole=foo" on the command line, and has
the result that you get _only_ the netconsole, because the hvc device is
never added as a preferred console. Worse still if you get the netconsole
configuration wrong somehow, you end up with no console at all.
As it turns out we don't need to worry about checking the command line.
If the user has specified "console=foo", then foo will be set as the
preferred console when the command line is parsed in start_kernel(), much
later than the pseries code, and so the latter setting will take effect.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the prototype for find_udbg_vterm() into pseries.h, removing
it from setup.c.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the way we calculate how much space to reserve for the
pHyp dump. Currently we reserve 256MB only. With this change, the
code first checks to see if an amount has been specified on the boot
command line with the "phyp_dump_reserve_size" option, and if so, uses
that much.
Otherwise it computes 5% of total ram and rounds it down to a multiple
of 256MB, and uses the larger of that or 256MB.
This is for large systems with a lot of memory (10GB or more). The
aim is to have more space available for the kernel on reboot on
machines with more resources. Although the dump will be collected
pretty fast and the memory released really early on allowing the
machine to have the full memory available, this alleviates any issues
that can be caused by having way too little memory on very very large
systems during those few minutes.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This changes the cpu_idle loop for 44x platforms to utilize the Wait Enable
feature of the CPU. This helps virtulization solutions know when the guest
Linux kernel is in an idle state.
A command line option called "idle" is also added to allow people to change
the idle loop back to the original variation. This is done by setting
"idle=spin" on the kernel command line.
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Now that we have the alpaca, the reg_save_ptr is no longer needed in the
paca. Eradicate all global uses of it and make it static in the iSeries
lpardata.c
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The iSeries HV only needs the first two fields of the paca statically
initialised, so create an alternate paca that contains only those and
switch to our real paca immediately after boot.
This is in order to make the 1024 cpu patches easier since they will no
longer have to statically initialise the pacas for iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Clean up the pwrficient iommu code a bit. It was using u32 *-based offsets
for registers, which can be a bit confusing when comparing to the manual.
Generated binaries from the code is unchanged from before.
Signed-off-by: Olof Johansson <olof@lixom.net>
A couple of places are duplicating the function of
of_device_is_available; convert them to use it.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
With a multiplatform kernel, once built we always have warp_setup_nand_flash()
called and NDFC probed, no matter what machine we actually run on. This
potentially can cause problems (such as kernel crash), since NDFC is probed at
a warp-predefined address.
Using machine_device_initcall() NAND devices are registered if we run on a warp only.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch creates a common system reset routine for all 40x and 44x
systems. Previously only a 44x routine existed. But since this system
reset via the debug control register is common for 40x and 44x let's
share this code for all those platforms in ppc4xx_soc.c.
This patch also enables CONFIG_4xx_SOC for all 40x and 44x platforms.
Tested on Kilauea (405EX) and Canyonlands (440EX).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split the device setup code in ps3_register_repository_device() in two
routines:
1. ps3_setup_static_device(), to handle the setup of static devices in the
PS3 repository, which can be __init,
2. ps3_setup_dynamic_device(), to handle the setup of storage devices that
may appear later in the PS3 repository.
This fixes a few section mismatch warnings.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 save power on halt:
- Replace infinite busy loops by smarter loops calling
lv1_pause() to save power.
- Add ps3_halt() and ps3_sys_manager_halt().
- Add __noreturn annotations.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a new routine ps3_get_speid() which returns the logical
SPE ID. This ID is needed for profiling support.
Signed-off-by: Takashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a typo bug 'unlikely(x) == y' and add an unlikely() call to
an unlikely code path in the PS3 interrupt routine ps3_get_irq().
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, ppu-gdb can't trace spu infomation with coredump generated
by the kernel. While the core dumps notes have correct contents, they
have the wrong names, as the file descriptors used to generate the note
names are off-by-one. An application that opens a SPE context as fd 3,
the current core dump code will generate notes like:
SPU/4/mem
SPU/4/regs
etc.
This confuses GDB, which knows it is looking for SPE context 3 (from
parsing the spu_context_run system call arguments), and cannot find
any notes that match context 3.
This change corrects the file descriptor counting, to only increment
the fd until after we've written the note name.
Signed-off-by: Gerhard Stenzel <stenzel@de.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
During the context save process, we currently save the MFC command
channel after purging the MFC queues. This causes a systemsim warning,
as the command channel may be in an unknown state after the purge.
This change does the save before purging the MFC queues.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
During spu_process callback, we release then acquire the SPU, but keep a
pointer to the local store memory. Since the context may have been
scheduled out during the callback, the ls pointer may become invalid.
This change reacquires the pointer to the context local store after
spu_acquire()-ing, so that it isn't invalidated by a context switch.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
All of the single-value files in spufs are terminated by a newline,
except for signal1_type and signal2_type.
This change adds a trailing newline to these two files.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.
The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: Alexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.
The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.
Tested on AMCC Taishan 440GX.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The AMCC 440EP Yosemite board is very similar to the original AMCC Bamboo
board. This adds a YOSEMITE option to Kconfig, and reuses the existing
bamboo board support in the kernel.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Canyonlands is the AMCC 460EX eval board, featuring nearly all of the 460EX
interfaces:
- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA port
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
scanlog_init() could use some love.
* properly return -ENODEV if this system doesn't support scan-log-dump
* don't printk if scan-log-dump not present; only older systems have it
* convert from create_proc_entry() to preferred proc_create()
* allocate zeroed data buffer
* fix potential memory leak of ent->data on failed create_proc_entry()
* simplify control flow
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds /sys/kernel/phyp_dump_active so that kdump init scripts may
look for it and take appropriate action if this file is found. This
file is only created when phyp_dump has been registered.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a kernel command line option "phyp_dump", which takes a 0/1
value for disabling/ enabling phyp_dump at boot time. Kdump can use
this on cmdline (phyp_dump=0) to disable phyp-dump during boot when
enabling itself. This will ensure only one dumping mechanism is active
at any given time.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This tracks the size freed. For now it does a simple rudimentary
calculation of the ranges freed. The idea is to keep it simple at the
external shell script level and send in large chunks for now.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds routines to
a. invalidate dump
b. calculate region that is reserved and needs to be freed. This is
exported through sysfs interface.
Unregister has been removed for now as it wasn't being used.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Set up the actual dump header, register it with the hypervisor.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Check to see if there actually is data from a previously
crashed kernel waiting. If so, allow user-space tools to
grab the data (by reading /proc/kcore). When user-space
finishes dumping a section, it must release that memory
by writing to sysfs. For example,
echo "0x40000000 0x10000000" > /sys/kernel/release_region
will release 256MB starting at the 1GB. The released memory
becomes free for general use.
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Initial patch for reserving memory in early boot, and freeing it
later. If the previous boot had ended with a crash, the reserved
memory would contain a copy of the crashed kernel data.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The functions time_before, time_before_eq, time_after, and
time_after_eq are more robust for comparing jiffies against other
values.
This implements usage of the time_after() macro, defined at
linux/jiffies.h, which deals with wrapping correctly.
Signed-off-by: S.Çağlar Onur <caglar@pardus.org.tr>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The hypervisor can look at the value in the wait_state_cycles field of
the VPA for an estimate of how busy dedicated processors are.
Currently, as the kernel never touches this field, we appear to be
100% busy. This records the duration the kernel is in powersave and
passes that to the HV to provide a reasonable indication of
utilisation.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This function has been a no-op for about 18 months; it's there in
the history should anyone need to resurrect it.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Prevailing practice for define_machine() in powerpc is to use the
platform name when the platform has only one define_machine()
statement, but maple uses "maple_md". This caused me some
head-scratching when writing some new code that uses
machine_is(maple).
Use "maple" instead of "maple_md". There should not be any behavioral
change -- fixup_maple_ide() calls machine_is(maple) but the body of
the function is ifdef'd out.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI bridge representing the PCIE root complex on Axon, contains
device BARs for a memory range and ROM that define inbound accesses.
This confuses the kernel resource management code -- the resources
need to be hidden when Axon is a host bridge.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cell IOMMU code to parse the dma-ranges properties, used for the fixed
mapping, was broken in two ways for some devices.
Firstly it didn't cope with empty dma-ranges properties. An empty property
implies no translation so can be safely skipped.
The code also wrongly assumed it would be looking at PCI devices, and hard
coded the number of address and size cells.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When building arch/powerpc/platforms/powermac/pic.c when !CONFIG_ADB_PMU
we get the following warnings:
arch/powerpc/platforms/powermac/pic.c: In function 'pmacpic_find_viaint':
arch/powerpc/platforms/powermac/pic.c:623: warning: label 'not_found' defined but not used
This fixes it.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, we can hit the BUG_ON in __spu_update_sched_info by reading
the regs file of a context between two calls to spu_run. The
spu_release_saved called by spufs_regs_read() is resulting in the (now
non-runnable) context being placed back on the run queue, so the next
call to spu_run ends up in the bug condition.
This change uses the SPU_SCHED_SPU_RUN flag to only reschedule a context
if it's still in spu_run().
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
commit 4ef11014 introduced a usage of SCHED_IDLE to detect when
a context is within spu_run.
Instead of SCHED_IDLE (which has other meaning), add a flag to
sched_flags to tell if a context should be running.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Not all e300 cores support the performance monitors, and the ones
that don't will be confused by the mf/mtpmr instructions. This
allows the support to be optional, so the 8349 can turn it off
while the 8379 can turn it on. Sadly, those aren't config options,
so it will be left to the defconfigs and the users to make that
determination.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add functions to manage the channel syncronization flags to dma_lib
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Also stop both rx and tx sections before changing the configuration of
the dma device during init.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
The only tricky part is we need to adjust the PTE insertion loop to
cater for holes in the page table. The PTEs for each segment start on
a 4K boundary, so with 16M pages we have 16 PTEs per segment and then
a gap to the next 4K page boundary.
It might be possible to allocate the PTEs for each segment separately,
saving the memory currently filling the gaps. However we'd need to
check that's OK with the hardware, and that it actually saves memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make some preliminary changes to cell_iommu_alloc_ptab() to allow it to
take the page size as a parameter rather than assuming IOMMU_PAGE_SIZE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We use n_pte_pages to calculate the stride through the page tables, but
we also use it to set the NPPT value in the segment table entry. That is
defined as the number of 4K pages per segment, so we should calculate
it as such regardless of the IOMMU page size.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the cell IOMMU code allocates the entire IOMMU page table in a
contiguous chunk. This is nice and tidy, but for machines with larger
amounts of RAM the page table allocation can fail due to it simply being
too large.
So split the segment table and page table setup routine, and arrange to
have the dynamic and fixed page tables allocated separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's no need to allocate the pad page unless we're going to actually
use it - so move the allocation to where we know we're going to use it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cell IOMMU code no longer needs to save the pte_offset variable
separately, it is incorporated into tbl->it_offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cell IOMMU tce build and free routines use pte_offset to convert
the index passed from the generic IOMMU code into a page table offset.
This takes into account the SPIDER_DMA_OFFSET which sets the top bit
of every DMA address.
However it doesn't cater for the IOMMU window starting at a non-zero
address, as the base of the window is not incorporated into pte_offset
at all.
As it turns out tbl->it_offset already contains the value we need, it
takes into account the base of the window and also pte_offset. So use
it instead!
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It's called the fixed mapping, not the static mapping.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ulrich Weigand has found that the hardware watchpoints on cell were not
working back in November :
http://ozlabs.org/pipermail/linuxppc-dev/2007-November/046135.html
This patch sets them during initialization.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This moves the private DABRX definitions for celleb from beat.h to
reg.h to make them usable for all.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The spu_runcntl_RW register is restored within spu_restore function.
So, at the end of spu_bind_context, the SPU context is not just loaded,
but running.
This change corrects the state switch to account the time as USER.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There is a potential race between flushes of the entire SLB in the MFC
and the point where new entries are being established. The problem is
that we might put a ESID entry into the MFC SLB when the VSID entry has
just been cleared by the global flush.
This can be circumvented by holding the register_lock throughout both
the flushing and the creation of SLB entries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When we replace an SLB entry in the MFC after using up all the available
entries, there is a short window in which an incorrect entry is marked
as valid.
The problem is that the 'valid' bit is stored in the ESID, which is
always written after the VSID. Overwriting the VSID first will make the
original ESID entry point to the new VSID, which means that any
concurrent DMA accessing the old ESID ends up being redirected to the
new virtual address. A few cycles later, we write the new ESID and
everything is fine again.
That race can be closed by writing a zero entry to the ESID first, which
makes sure that the VSID is not accessed until we write the new ESID.
Note that we don't actually need to invalidate the SLB entry using the
invalidation register, which would also flush any ERAT entries for that
segment, because the segment translation does not become invalid but is
only removed from the SLB cache.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There is a small race between the context save procedure
and the SPU interrupt handling, where we expect all interrupt
processing to have finished after disabling them, while
an interrupt is still being processed on another CPU.
The obvious fix is to call synchronize_irq() after disabling
the interrupts at the start of the context save procedure
to make sure we never access the SPU any more during an
ongoing save or even after that.
Thanks to Benjamin Herrenschmidt for pointing this out.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we get the following output from sputrace:
[5.097935954] 1606: spufs_ps_nopfn__enter (thread = 1605, spu = -1)
[5.097958164] 1606: spufs_ps_nopfn__insert (thread = 1605, spu = 15)
[5.097973529] 1607: spufs_ps_nopfn__enter (thread = 1605, spu = -1)
[5.097989174] 1607: spufs_ps_nopfn__insert (thread = 1605, spu = 14)
Which leads me to believe that 160[67] is the current thread ID, and
1605 is the context backing the psmap.
However, the 'current' and 'owner' tids are reversed - the 'current'
tid is on the right. This change puts the current thread ID in the
left-hand column instead, and renames the right to 'ctxthread'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
At present, we have a situation where a context with no owner is
re-scheduled by spu_forget:
Thread 1: reading regs file Thread 2: context owner
spu_forget()
- ctx->owner = NULL
- set SPU_SCHED_WAS_ACTIVE
spu_acquire_saved()
- context is in saved state
spu_release_saved()
- SPU_SCHED_WAS_ACTIVE is set,
so spu_activate() the context,
which now has no owner
In spu_forget(), we shouldn't be requesting a re-schedule by setting
SPU_SCHED_WAS_ACTIVE. This change removes the set_bit in spu_forget(),
so that spu_release_saved() doesn't reinsert this destroyed context on
to the run queue.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
We have a small window where a spu context may be destroyed while
we're servicing a page fault (from another thread) to the context's
problem state mapping.
After we up_read() the mmap_sem, it's possible that the context is
destroyed by its owning thread, and so the later references to ctx
are invalid. This can maifest as a deadlock on the (now free()-ed)
context state mutex.
This change adds a reference to the context before we release the
mmap_sem, so that the context cannot be destroyed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
m8xx_setup.c says:
/* Force all 8xx processors to use divide by 16 processor clock. */
And at the same time it is using bus-frequency for calculating
timebase. It is okay for most setups because bus-frequency is
equal to clock-frequency.
The problem emerges when cpu frequency is > 66MHz, quoting
u-boot/cpu/mpc8xx/speed.c:
if (gd->cpu_clk <= 66000000) {
sccr_reg |= SCCR_EBDF00; /* bus division factor = 1 */
gd->bus_clk = gd->cpu_clk;
} else {
sccr_reg |= SCCR_EBDF01; /* bus division factor = 2 */
gd->bus_clk = gd->cpu_clk / 2;
}
So in case of cpu clock > 66MHz, bus_clk = cpu_clk / 2. An then, from
Linux, we calculate timebase frequency as tb_freq = bus_clk / 16,
that is cpu_clk / 2 / 16, which is wrong.
This fixes the system time drifting problem on the EP885C board
running at 133MHz.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For memory remove, we need to clean up htab mappings for the
section of the memory we are removing.
This implements support for removing htab bolted mappings for pSeries
logical partitions. Other sub-archs may need to implement similar
functionality for hotplug memory remove to work on them.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mpc52xx_set_psc_clkdiv is needed by PSC device drivers.
Signed-off-by: Eric Dujardin <eric.dujardin@sagem.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Setup i2c_board_info based on device tree contents. This has to be
a device_initcall since we need PCI to be probed by the time we
run it, but before the actual driver is initialized.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
At present, the __spufs_trap_data_map and __spu_trap_data_seq functions
exit if spu->flags has the SPU_CONTEXT_SWITCH_ACTIVE set. This was
resulting in suprious returns from these functions, as they may be
legitimately called when we have this bit set.
We only use it in these two sanity checks, so this change removes the
flag completely. This fixes hangs in the page-fault path of SPE apps.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Introduced by commit 79393fc46e
("kobject: convert pseries/power.c to kobj_attr interface").
sys_create_file takes a "struct attrbute *" not a "struct
kobj_addribute *".
arch/powerpc/platforms/pseries/power.c: In function 'apo_pm_init':
arch/powerpc/platforms/pseries/power.c:78: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
2.6.25 has a regression where we can starve the scheduler by creating
(N_SPES+1) contexts, then running them one at a time.
The final context will never be run, as the other contexts are loaded on
the SPEs, none of which are repoted as free (ie, spu->alloc_state !=
SPU_FREE), so spu_get_idle() doesn't give us a spu to run on. Because
all of the contexts are stopped, none are descheduled by the scheduler
tick, as spusched_tick returns if spu_stopped(ctx).
This change replaces the spu_stopped() check with checking for SCHED_IDLE
in ctx->policy. We set a context's policy to SCHED_IDLE when we're not
in spu_run(). We also favour SCHED_IDLE contexts when looking for contexts
to unbind, but leave their timeslice intact for later resumption.
This patch fixes the following test in the spufs-testsuite:
tests/20-scheduler/02-yield-starvation
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Remove unused CONFIG_WANT_DEVICE_TREE
[POWERPC] Cell RAS: Remove DEBUG, and add license and copyright
[POWERPC] hvc_rtas_init() must be __init
[POWERPC] free_property() must not be __init
[POWERPC] vdso_do_func_patch{32,64}() must be __init
[POWERPC] Remove generated files on make clean
[POWERPC] Fix arch/ppc compilation - add typedef for pgtable_t
[POWERPC] Wire up new timerfd syscalls
[POWERPC] PS3: Update sys-manager button events
[POWERPC] PS3: Sys-manager code cleanup
[POWERPC] PS3: Use system reboot on restart
[POWERPC] PS3: Fix bootwrapper hang bug
[POWERPC] PS3: Fix reading pm interval in logical performance monitor
[POWERPC] PS3: Fix setting bookmark in logical performance monitor
[POWERPC] Fix DEBUG_PREEMPT warning when warning
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the central patch of a cleanup series. In most cases there is no good
reason why someone would want to use a dentry for itself. This series reflects
that fact and embeds a struct path into nameidata.
Together with the other patches of this series
- it enforced the correct order of getting/releasing the reference count on
<dentry,vfsmount> pairs
- it prepares the VFS for stacking support since it is essential to have a
struct path in every place where the stack can be traversed
- it reduces the overall code size:
without patch series:
text data bss dec hex filename
5321639 858418 715768 6895825 6938d1 vmlinux
with patch series:
text data bss dec hex filename
5320026 858418 715768 6894212 693284 vmlinux
This patch:
Switch from nd->{dentry,mnt} to nd->path.{dentry,mnt} everywhere.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix cifs]
[akpm@linux-foundation.org: fix smack]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_DEVICE_TREE was the only user of CONFIG_WANT_DEVICE_TREE but
it was removed in commit id 2543133381
(bootwrapper: Build multiple cuImages).
This removes CONFIG_WANT_DEVICE_TREE from Kconfig and the defconfigs.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/cell/ras.c still has DEBUG #defined, which is no
longer necessary. Disable it - this disables two pr_debugs().
While we're there this file should have a copyright notice and license,
so add both.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following section mismatch:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x55648): Section mismatch in reference from the function .free_node() to the function .init.text:.free_property()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
RCU style multiple probes support for the Linux Kernel Markers. Common case
(one probe) is still fast and does not require dynamic allocation or a
supplementary pointer dereference on the fast path.
- Move preempt disable from the marker site to the callback.
Since we now have an internal callback, move the preempt disable/enable to the
callback instead of the marker site.
Since the callback change is done asynchronously (passing from a handler that
supports arguments to a handler that does not setup the arguments is no
arguments are passed), we can safely update it even if it is outside the
preempt disable section.
- Move probe arm to probe connection. Now, a connected probe is automatically
armed.
Remove MARK_MAX_FORMAT_LEN, unused.
This patch modifies the Linux Kernel Markers API : it removes the probe
"arm/disarm" and changes the probe function prototype : it now expects a
va_list * instead of a "...".
If we want to have more than one probe connected to a marker at a given
time (LTTng, or blktrace, ssytemtap) then we need this patch. Without it,
connecting a second probe handler to a marker will fail.
It allow us, for instance, to do interesting combinations :
Do standard tracing with LTTng and, eventually, to compute statistics
with SystemTAP, or to have a special trigger on an event that would call
a systemtap script which would stop flight recorder tracing.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mike Mason <mmlnx@us.ibm.com>
Cc: Dipankar Sarma <dipankar@in.ibm.com>
Cc: David Smith <dsmith@redhat.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "Frank Ch. Eigler" <fche@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.25' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Add arch-specific walk_memory_remove() for 64-bit powerpc
[POWERPC] Enable hotplug memory remove for 64-bit powerpc
[POWERPC] Add remove_memory() for 64-bit powerpc
[POWERPC] Make cell IOMMU fixed mapping printk more useful
[POWERPC] Fix potential cell IOMMU bug when switching back to default DMA ops
[POWERPC] Don't enable cell IOMMU fixed mapping if there are no dma-ranges
[POWERPC] Fix cell IOMMU null pointer explosion on old firmwares
[POWERPC] spufs: Fix timing dependent false return from spufs_run_spu
[POWERPC] spufs: No need to have a runnable SPU for libassist update
[POWERPC] spufs: Update SPU_Status[CISHP] in backing runcntl write
[POWERPC] spufs: Fix state_mutex leaks
[POWERPC] Disable G5 NAP mode during SMU commands on U3
Add a .show_options super operation to spufs.
Use generic_show_options() and save the complete option string in
spufs_fill_super().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
simple_attr_close implementes ->release so it should be named accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes simple attributes might need to return an error, e.g. for
acquiring a mutex interruptibly. In fact we have that situation in
spufs already which is the original user of the simple attributes. This
patch merged the temporarily forked attributes in spufs back into the
main ones and allows to return errors.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <stefano.brivio@polimi.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the cell IOMMU fixed mapping just printks that it's been setup,
which is not particularly useful. Much more interesting is the address
ranges for the different windows. This adds one line to dmesg on a blade.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we get a 64-bit dma mask we switch to the fixed ops and call
cell_dma_dev_setup(). If the driver then switches back to a 32-bit dma
mask for any reason we don't call cell_dma_dev_setup() again, which
has the potential to leave bogus data in dev->archdata.dma_data.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In order for the cell IOMMU fixed mapping to work we need "dma-ranges"
properties in the device tree. If there are none then there's no point
enabling the fixed mapping support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cell IOMMU fixed mapping support has a null pointer bug if you run
it on older firmwares that don't contain the "dma-ranges" properties.
Fix it and convert to using of_get_next_parent() while we're there.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Stop bits are only valid when the running bit is not set. Status bits
carry over from one invocation of spufs_run_spu() to another, so the
RUNNING bit gets added to the previous state of the register which may
have been a remote library call. In this case, it looks like another
library routine should be invoked, but the spe is actually running.
This fixes a problem with a testcase that exercises the scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We don't need to update the libassist statistic with the context in a
runnable state, so do it after spu_disable_spu().
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, the kernel may fail to restart a SPE context which
has stopped and been swapped out.
This changes spu_backing_runcntl_write to emulate the real
SPU_Status register exactly. When the SPU Run Control register
is written with SPU_RunCntl[Run] set to '1', the physical SPU
automatically sets SPU_Status[R] and clears SPU_Status[CISHP].
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix various state_mutex leaks. The worst one was introduced by the
interrutible state_mutex conversion but there've been a few before
too. Notably spufs_wait now returns without the state_mutex held
when returning an error, which actually cleans up some code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that with the U3 northbridge, if the processor is in NAP
mode the whole time while waiting for an SMU command to complete,
then the SMU will fail. It could be related to the weird backward
mechanism the SMU uses to get to system memory via i2c to the
northbridge that doesn't operate properly when the said bridge is
in napping along with the CPU. That is on U3 at least, U4 doesn't
seem to be affected.
This didn't show before NO_HZ as the timer wakeup was enough to make
it work it seems, but that is no longer the case.
This fixes it by disabling NAP mode on those machines while
an SMU command is in flight.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
While merging, I found a small bug that I forgot to send. I add an
offset to a value twice.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The addition of of_rtc for the Walnut board was only half complete. Select
OF_RTC in the Kconfig and include the appropriate header to make it compile.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The xics code does update the default server information when the boot
cpu is removed. This patch recognizes when the boot cpu is being
removed and updates the appropriate information based on the new 'boot
cpu'.
Failure to update this information can causes us to leave irqs pinned
to cpus that are being removed, especially when removing the boot cpu.
The cpu is removed from the kernel, but cpu dlpar remove operations
fail since we cannot return the cpu to the hypervisor.
Signed-off-by: Nathan Fonteno <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It appears that xics.c has its own of_get_cpu_node(). Remove this and
use the common one from prom.c.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This splits off the kexec path bits of the xics_teardown_cpu() routine
into its own xics_kexec_teardown_cpu() routine. With the previous
combined routine the CPPR for a cpu that is being removed may have its
CPPR reset in the plpar_eoi() call (which explicitly sets the CPPR to
a non-zero value). Splitting of the kexec bits of the code prevents
this from happening in the cpu remove path.
Once again, this does not cause the cpu remove from the kernel to
fail, but it does cause cpu dlpar operations to not be able to return
the cpu to the hypervisor.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The affinity mask in the virq descriptor needs to be set before we
reset the affinity for the virq. Without doing this the call to get
the new irq server fails and we end up leaving the virq pinned to the
cpu we are removing.
This does not fail the cpu remove from the kernel, but it does prevent
cpu dlpar remove operations from returning the cpu to the hypervisor.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
512x is very similar to 83xx and most
of this is patterned after code from 83xx.
New platform:
changed:
arch/powerpc/Kconfig
arch/powerpc/platforms/Kconfig
arch/powerpc/platforms/Kconfig.cputype
arch/powerpc/platforms/Makefile
new:
arch/powerpc/platforms/512x/*
include/asm-powerpc/mpc512x.h
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
calibrate_delay() must be __cpuinit, not __{dev,}init.
I've verified that this is correct for all users.
While doing the latter, I also did the following cleanups:
- remove pointless additional prototypes in C files
- ensure all users #include <linux/delay.h>
This fixes the following section mismatches with CONFIG_HOTPLUG=n,
CONFIG_HOTPLUG_CPU=y:
WARNING: vmlinux.o(.text+0x1128d): Section mismatch: reference to .init.text.1:calibrate_delay (between 'check_cx686_slop' and 'set_cx86_reorder')
WARNING: vmlinux.o(.text+0x25102): Section mismatch: reference to .init.text.1:calibrate_delay (between 'smp_callin' and 'cpu_coregroup_map')
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christian Zankel <chris@zankel.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mainly, this involves two changes:
1) xilinx->xlnx (recognized standard is to use the stock ticker)
2) In order to have the device tree focus on describing what the
hardware is as exactly as possible, the compatible strings contain the
full IP name and IP version.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Of_get_parent and of_find_compatible_node do a of_node_get, and thus a
corresponding of_code_put is needed in both the error case and the normal
return case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = \(of_get_parent\|of_find_compatible_node\)(...);
if (E == NULL) S
... when != of_node_put(...,(T1)E,...)
when != if (E != NULL) { ... of_node_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != of_node_put(...,(T2)E,...)
when != if (E != NULL) { ... of_node_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Of_get_parent and of_find_compatible_node do an of_node_get, and thus a
corresponding of_code_put is needed in the error case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = \(of_get_parent\|of_find_compatible_node\)(...);
if (E == NULL) S
... when != of_node_put(...,(T1)E,...)
when != if (E != NULL) { ... of_node_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != of_node_put(...,(T2)E,...)
when != if (E != NULL) { ... of_node_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc/platforms/83xx/mpc832x_rdb.c: In function ‘mpc832x_rdb_setup_arch’:
arch/powerpc/platforms/83xx/mpc832x_rdb.c:104: warning: ‘np’ is used uninitialized in this function
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e300 c3 and c4 variants support hardware performance monitor counters
which are identical to those found in the e500.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the more recent e300 cores have the same performance monitor
implementation as the e500. e300 isn't book-e, so the name isn't
really appropriate. In preparation for e300 support, rename a bunch
of fsl_booke things to say fsl_emb (Freescale Embedded Performance Monitors).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cleaned up IRQ layout and removed unsused ISU allocations.
Fixed RTC address typo from /dts-v1/ conversion.
Incorporated list suggestions to use an "iomega," vendor prefix,
and to use a node reference rather than a hard path.
Signed-off-by: Jon Loeliger <jdl@@jdl.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I got this warning from gcc:
arch/powerpc/platforms/cell/axon_msi.c:118: warning: 'tmp' may be used uninitialized in this function
Which turns out to be a false positive, but pointed out that it was
possible for the error path in find_msi_translator() to do an extra
of_node_put on a node. This fixes it by localising the ref counting
a bit. As a side effect, the warning goes away.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a brown-paper-bag bug in axon_msi, we pass the address of our
FIFO directly to the hardware, without DMA mapping it. This leads to
DMA exceptions if you enable MSI & the IOMMU.
The fix is to correctly DMA map the fifo, dma_alloc_coherent() does
what we want - and we need to track the virt & phys addresses.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we create of_platform devices earlier on cell, we can make the
axon_msi driver an of_platform driver. This makes the code cleaner in
several ways, and most importantly means we have a struct device.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently cell publishes OF devices at device_initcall() time, which
means the earliest a driver can bind to a device is also device_initcall()
time. We have a driver we want to register before other devices, so
publish the devices at subsys_initcall() time.
This should not cause any behaviour change for existing drivers, as they
are still bound at device_initcall() time.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
asm/commproc.h was renamed to asm/cpm1.h
sysdev/commproc.h was renamed to platforms/8xx/mpc8xx.h
m8xx_pic_init was renamed to mpc8xx_pics_init
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reference count for the "neighbor" spu context was not
being correctly decremented after usage.
So, contexts used as reference during SPU affinity setup
were not being deallocated, leading to a memory leak.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we only catch debug events through the 0x3fff status;
spufs_run_spu doesn't handle single-step SPE events.
This change adds a handler for conditions where the SPE is stopped due
to single-step-mode.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds markers two important points in the spufs code and a new
module (sputrace.ko) that allows reading these out through a proc file.
Long-term I'd rather see something like lttng extended to use the spufs
instrumentation, but for now I think this is a good enough quick
solution. We'll probably want to add various addition event in addition
to that ones I have already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SCCR USB bits are in a different location on the mpc8315.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch converts PPC's IOMMU to use the IOMMU helper functions. The IOMMU
doesn't allocate a memory area spanning LLD's segment boundary anymore.
iseries_hv_alloc and iseries_hv_map don't have proper device
struct. 4GB boundary is used for them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
[POWERPC] pasemi: Fix thinko in dma_direct_ops setup
The first patch will just fall through and still set dma_data to a bad
value, make it return directly instead.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More late-caught fallout from the mainline merge. Commit
35e4a6e26d ("[POWERPC] Use
archdata.dma_data in dma_direct_ops and add the offset") claimed
"Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, ..."
..but nope -- the pasemi iommu setup code that disables translation on
the DMA pci device didn't set dma_data correctly.
This fixes it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for setting up a fixed IOMMU mapping on certain
cell machines. For 64-bit devices this avoids the performance overhead of
mapping and unmapping pages at runtime. 32-bit devices are unable to use
the fixed mapping.
The fixed mapping is established at boot, and maps all of physical memory
1:1 into device space at some offset. On machines with < 30 GB of memory
we setup the fixed mapping immediately above the normal IOMMU window.
For example a machine with 4GB of memory would end up with the normal
IOMMU window from 0-2GB and the fixed mapping window from 2GB to 6GB. In
this case a 64-bit device wishing to DMA to 1GB would be told to DMA to
3GB, plus any offset required by firmware. The firmware offset is encoded
in the "dma-ranges" property.
On machines with 30GB or more of memory, we are unable to place the fixed
mapping above the normal IOMMU window as we would run out of address space.
Instead we move the normal IOMMU window to coincide with the hash page
table, this region does not need to be part of the fixed mapping as no
device should ever be DMA'ing to it. We then setup the fixed mapping
from 0 to 32GB.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the ioid fetching and checking logic so we can use it elsewhere
in a subsequent patch.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support to cell_iommu_setup_page_tables() for handling two windows,
the dynamic window and the fixed window. A fixed window size of 0
indicates that there is no fixed window at all.
Currently there are no callers who pass a non-zero fixed window, but the
upcoming fixed IOMMU mapping patch will change that.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split the IOMMU logic out from cell_dma_dev_setup() into a separate
function. If we're not using dma_direct_ops or dma_iommu_ops we don't
know what the hell's going on, so BUG.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split cell_iommu_setup_hardware() into two parts. Split the page table
setup into cell_iommu_setup_page_tables() and the bits that kick the
hardware into cell_iommu_enable_hardware().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Split out the logic that allocates a struct iommu into a separate
function. This can fail however the calling code has never cared - so
just return if we can't allocate an iommu.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Forgot to export this one. Needed when pasemi_mac is compiled as a module.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi: DMA engine management library
Introduce a DMA management library to manage the various DMA resources
on the PA Semi SoCs. Since several drivers need to allocate these shared
resources, provide some abstractions as well as allocation/free functions
for channels, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '83xx' which existed only for compat with arch/ppc
* Removed Kconfig option 'PPC_MPC836x' since its not used
* Renamed Kconfig option 'MPC834x' to 'PPC_MPC834x' to match others
* Added a multiplatform 83xx defconfig (mpc83xx_defconfig).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Allow multiple boards to be selected in a single build
* Removed Kconfig option '85xx' which existed only for compat with arch/ppc
* Added a multiplatform 85xx defconfig (mpc85xx_defconfig). This builds
all 85xx boards except sbc8560 and stx_gp3 since these to boards have
board specific ifdef in driver code that may break all other boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
primarily based on mpc837x mds code.
Signed-off-by: Joe D'Abbraccio <ljd015@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8315 identical to mpc8313 here, just check compatible.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
prepare for adding support for the mpc8315 rdb, since they are
identical wrt platform code.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* "simple-bus" covers all our needs for of_platform_bus_probe()
* make device tree name just 'soc' not 'soc85..'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
