Post an FCH_EVT_LIPRESET event on lport reset as
as lport reset occurs on FIP cleat virtual link,
this could be due to change in fcoe vlan and this
event will allow user app fcoemon to switch to
new fcoe vlan.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: Linux based SW target (TCM) connected to windows initiator
was unable to satisfy write request of size > 2K.
Fix: Existing linux implememtation of FCoE stack is expecting sequence
number to match w.r.t incoming framme. When DDP is used on target in
response to write request from initiator, SW stack is notified only
when last data frame arrives and only the pakcket header of last data
frame is posted to NetRx queue of storage. When that last packet was
processed in libfc:Exchange layer, implementation was expecting
sequence number to match, but in this case sequence number which is
embedded in FC Header is assigned by windows initaitor, hence due to
sequence number mismatch post-processing which shall result into
sending RSP is not done. Enhanced the code to utilize the sequence
number of incoming last frame and process the packet so that, it will
eventually complete the write request by sending write response (RSP)
GOOD.
Notes/Dependencies: This patch is validated using windows and linux
initiator to make sure, it doesn't break anything.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: Selection of RX queue on target is based on RX-ID. FCoE used
8 Net Rx queues. HW post the packets based on rx_id %
num_rx_queue. Due to this has based filtering, only one CPU is busy
servicing incoming request including post-processing of incoming
request. This is gating factor because
1. Only one CPU is utilized 100% while others CPUs are not used at all.
2. CPU which received request assign "sequence' by selecting exchange
from per CPU pool (num_ddp_context / num_online_cpus,
approxi.). Due to which if if rate of incoming request is higher
than rate of servicing request, existing code path end of sending
"BUSY" response (SAM_STAT_BUSY because unable to allocate
exchange).
Fix: Fan-out incoming request to all other CPUs excluding the CPU
which is receiving all incoiming request. This path also addresses,
selecting same CPU based on rx_id from received frame for completion
of the request such as "releasing exchange to the per CPU Pool". This
fix is applicable for FCoE target since initiator code path already
takes care of selecting CPU to complete post-processing of request
once OX_ID is assigned.
Notes: N/A
Dependencines: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: Earlier mechanism of selection of CPU was, to select the same CPU
which has received incoming request. Hence in case of rx_id = 0xFFFF,
request was always posted to same NetRx queue, hence only 1 CPU is utilized
for handling the command. It was also causing problem of "running out of
exchanges from per CPU pool of exchanges (in case of DDP offload)
Fix: Implemented new algo. to select CPU for post-processing of
incoming commands when rx_id is unknown. This is simple Round robin
algo. for CPU selection.
Notes/Dependencies: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: When initiator sends write command to target, target tries to
assign new sequence. It allocates new exchangeID (RX_ID)
always from non-offloaded pool (Non-offload EMA)
Fix: Enhanced fcoe_oem_match routine to look at F_CTL flags and if it
is exchange responder and command type is WRITEDATA, then function
returns TRUE instead of FALSE. This function is used to determine
which pool to use (offload pool of exchange is used only if this
function returns TRUE).
Technical Notes: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add ddp_target() support to the Open-FCoE sw fcoe hba driver (fcoe.ko).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: Existing RPORT state machine continues witg FLOGI/PLOGI
process only after it receices beacon from other end. Once claiming
stage is over (either clain notify or clain repose), beacon is sent
and state machine enters into operational mode where it initiates the
rlogin process (FLOGI/PLOGI) to the peer but before this rlogin is
initiated, exitsing implementation checks if it received beacon from
other end, it beacon is not received yet, rlogin process is not
initiated. Other end initiates FLOGI but peer end keeps on rejecting
FLOGI, hence after 3 retries other end deletes associated rport, then
sends a beacon. Once the beacon is received, peer end now initiates
rlogin to the peer end but since associated rport is deleted FLOGI is
neither accepted nor the reject response send out because rport is
deleted. Hence unable to proceed withg FLOGI/PLOGI process and fails
to establish VN2VN connection.
Fix: VN2VN spec is not standard yet but based on exitsing collateral
on T11, it appears that, both end shall send beacon and enter into
'operational mode' without explictly waiting for beacon from other
end. Fix is to allow the RPORT login process as long as respective
RPORT is created (as part of claim notification / claim response) even
though state of RPORT is INIT. Means don't wait for beacon from peer
end, if peer end initiates FLOGI (means peer end exist and
responding).
Notes: This patch is preparing the FCoE stack for target wrt
offload. This is generic patch and harmless even if applied on storage
initiator because 'else if' condition of function 'fcoe_oem_found'
shall evaluate to TRUE only for targets.
Dependencies: None
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver should not call shutdown call from _scsih_remove otherwise,
The scsi midlayer can be deadlocked when devices are removed from the driver
pci_driver->shutdown handler.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Properly handling of target reset in multi-initiator environment
Clean up in broadcast change handling:
(1) Need to look at the status of each task management request, and retry
the TM when there are failures.
(2) Need quiescence IO so the driver doesn't take on more IO request while
it's in the middle of sending TM request to firmware
(3) Add support to keep track of how many pending broadcast AEN events
are received while the broadcast handling is active, then loop back at
the end of this routine if there were any events received.
Clean up in mpt2sas_scsih_issue_tm routine:
(1) Make sure proper status is returned when host reset fails
(2) Clean up sanity checks near end of routine, insuring all outstanding
IOs were completed.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This feature is to override the default
max_sectors setting at load time, taking max_sectors as an
command line option when loading the driver. The setting is
currently hard-coded in the driver to 8192 sectors (4MB transfers).
If max_sectors is specified at load time, minimum specified
setting will be 64, and the maximum is 8192. The driver will
modify the setting to be on even boundary. If max_sectors is not
specified, the driver will default to 8192.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
mpt2sas driver revision q header update:
(1) Modified the descriptions of the LocalAddress bit in the
Flags field of the MPI SGE Format description and the MPI
Simple Element.
(2) Modified Data Location Address Space bits in the Flags field
of the IEEE Chain Element.
(3) Added more detail to the description of the DataLength field
for the SCSI IO Request and Target Assist Request. Removed
restriction on using chained SGLs when using multicast or
bidirectional support.
(4) In Manufacturing Page 7, added ReceptacleID field to
ConnectorInfo, and reworked how the Pinout field is used.
(5) In IO Unit Page 7, added BoardTemperature and
BoardTemperatureUnits fields.
(6) In IOC Page 1, changed CoalescingTimeout to units of
half-microsecond and updated descriptions.
(7) Modified descriptions of SATASlumberTimeout and
SASSlumberTimeout fields in SAS IO Unit Page 5 to indicate
the timers start after partial mode is entered.
(8) Added Extended Manufacturing configuration pages.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch addresses many endian issues solved by runing sparse with the
option __CHECK_ENDIAN__ turned on.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver was incorrectly using the SLAB_CACHE_DMA flag when creating a cache
for SGLs. fnic device does not have 24-bit DMA restrictions. Remove the flag
and allocations from ZONE_DMA.
Thanks to Roland Dreier and David Rientjes for pointing out the bug.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added BSG interface support to BFA driver
- Adds support to send ELS/CT FC passthru commands and
few vendor specific BSG requests.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Moved FCS initialization, which internally does the im_port creation
as well as the scsi_host creation before bfa_init.
Once the bfa_init is complete & successful:
- Reset the FCS base port cfg params such as pwwn/nwwn and setup fc host
params - based on the values learned during the ioc getattr request.
- Change needed to support BSG commands even on bfa init failure.
- Model description fixes for Brocade adapters.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Enhancements to FCPIM module.
- Introduced IO tag management to allocate/release IOs to FCPIM module
from a free IOtag pool.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduce FC credit recovery.
- Added module parameter to enable/disable credit recovery.
Bug Fixes:
- Removed check for ignoring plogi from initiator in switched fabric mode.
- The ABTS for PLOGI is going out few millisecs earlier due to FW
timer calibration (around 300 miilisecs earlier). So there is a
window if an accept comes during this time HBA would have initiated
an ABORT.
- Added 1 to FC_ELS_TOV for compensating for FW timer.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support for 16Gbps.
- Added logic to flush pending mailbox command queue when IOC is disabled.
- Fix to Halt the flash controller during fw initialization - since
when asic blck is programmed flash controller's continuous access
blocks f/w access to flash.
- Added new asic based card types and modified IOC get card model routine.
- Added PLL init fix to do LPU reset every time we do a memory
initialization, since not doing so will cause LPU to be
uninitialized during driver load.
- Added fix to Halt flash controller before PLL initialization.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Introduced IOC poll mechanism which replaces current interrupt
based FW READY method.
- The timer based poll routine in IOC will query the ioc_fwstate
register to see if there is a state change in FW, and sends the READY event.
- Bug fixes in the new asic PLL initialization.
- Added logic to handle CPE/RME queue interrupts before iocfc config done.
1. Use the queue_process flag to see if iocfc configuration is done
in INTX mode.
2. Split the MSIX handler installation in two - one for IOC intr
handler and the other for cpe/rme queue handler - and delay
assigning queue handlers until iocfc config is done in MSIX mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Made changes to FCS lport, vport state machines to support vport
enable / disable operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support for Brocade-1860 Fabric Adapter.
- Made changes to support single firmware image per asic type.
- Combined bfi_cbreg.h and bfi_ctreg.h defines into bfi_reg.h with
only minimal defines used by host.
- Added changes to setup CPE/RME Queue register offsets based on
firmware response.
- Removed queue register offset initializations and added register offsets
to BFI config response message.
- Added Brocade-1860 asic specific interrupt status definitions and
mailbox interfaces.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Introduced a generic event notification callback function that
receives IOC_ENABLED, IOC_DISABLED, IOC_FAILED events and notifies the
modules registered for these events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Avoid the use of hardware defined structure bfi_sge_s for DMA
requests in host.
- Defined a generic address len pair to represent a DMA memory chunk
(bfi_alen_s).
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes:
drivers/scsi/sun3_NCR5380.c:475: warning: ‘merge_contiguous_buffers’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sam Creasey <sammy@sammy.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes a.o.:
drivers/scsi/sun3_scsi.h:225:5: warning: "NDEBUG" is not defined
drivers/scsi/sun3_scsi.h:345:14: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/sun3_scsi.h:351:14: warning: "NDEBUG_TAGS" is not defined
drivers/scsi/sun3_scsi.h:357:14: warning: "NDEBUG_MERGING" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes:
drivers/scsi/sun3_NCR5380.c:1448:5: warning: "NCR_TIMEOUT" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
and call it from sun3scsi_release(), cfr. the other NCR5380 drivers.
This fixes:
drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
WARNING: vmlinux.o(.text+0x18545c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x18556c): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187692): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x187770): Section mismatch in reference from the function sun3scsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes:
drivers/scsi/mac_scsi.c:220:5: warning: "NDEBUG_ABORT" is not defined
drivers/scsi/mac_scsi.c:271:5: warning: "NDEBUG_ABORT" is not defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
WARNING: vmlinux.o(.text+0x1ecd3e): Section mismatch in reference from the function macscsi_detect() to the function .devinit.text:NCR5380_init()
WARNING: vmlinux.o(.text+0x1ecddc): Section mismatch in reference from the function macscsi_detect() to the function .init.text:NCR5380_print_options()
WARNING: vmlinux.o(.text+0x1ece60): Section mismatch in reference from the function macscsi_detect() to the function .init.text:NCR5380_print_options()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
and call it from atari_scsi_release(), cfr. the other NCR5380 drivers.
This fixes:
drivers/scsi/NCR5380.h:303: warning: ‘NCR5380_exit’ declared ‘static’ but never defined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add ISA PNP IDs of the following cards to aha152x driver:
AVA-1502
AVA-1505
AHA-1510
AVA-1515
AHA-1520
AHA-1522
AHA-1530
AHA-1532
AIC-6360
(list from SCSI.INF file)
This makes my AHA-1530P card (has ADP3015 ID) work automatically.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Noticed that when the sysfs interface of the SCSI SES
driver was used to request a fault indication the LED
flashed but the buzzer didn't sound. So it was doing
what REQUEST IDENT (locate) should do.
Changelog:
- fix the setting of REQUEST FAULT for the device slot
and array device slot elements in the enclosure control
diagnostic page
- note the potentially defective code that reads the
FAULT SENSED and FAULT REQUESTED bits from the enclosure
status diagnostic page
The attached patch is against git/scsi-misc-2.6
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
commit 8ce7955aa5 ("[SCSI] atari_NCR5380:
update_timeout removal") removed all users, but not the avtual variable.
Suggested-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Using the current NEXT() macro for both lvalues and rvalues gives:
In file included from drivers/scsi/sun3_scsi.c:623:
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_queue_command_lck’:
drivers/scsi/sun3_NCR5380.c:993: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_main’:
drivers/scsi/sun3_NCR5380.c:1147: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c: In function ‘NCR5380_information_transfer’:
drivers/scsi/sun3_NCR5380.c:2277: warning: assignment discards qualifiers from pointer target type
drivers/scsi/sun3_NCR5380.c:2333: warning: assignment discards qualifiers from pointer target type
Change NEXT() to operate on rvalues only(), and introduce SET_NEXT() to
operate on lvalues, as is done in drivers/scsi/atari_NCR5380.c.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Deleting NPIV port causes a kernel panic when the NPIV port is in the same zone
as the physical port and shares the same LUN. This happens due to the fact that
vport destroy and unsolicited ELS are scheduled to run on the same workqueue,
and vport destroy destroys the lport and the unsolicited ELS tries to access
the invalid lport. This patch fixes this issue by maintaining a list of valid
lports and verifying if the lport is valid or not before accessing it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Do not set io_req->sc_cmd to NULL until bnx2fc_unmap_sg_list() is called to
enable it to unmap the DMA mappings.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NIC partitioned interfaces reports the speed of 2500 which was not handled by
the driver.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Enabling DEBUG_STRICT_USER_COPY_CHECKS causes the following
warning:
In file included from arch/x86/include/asm/uaccess.h:573,
from include/linux/uaccess.h:5,
from include/linux/highmem.h:7,
from include/linux/pagemap.h:10,
from include/linux/blkdev.h:12,
from drivers/scsi/lpfc/lpfc_debugfs.c:21:
In function 'copy_from_user':
arch/x86/include/asm/uaccess_64.h:65:
warning: call to 'copy_from_user_overflow' declared with
attribute warning: copy_from_user() buffer size is not provably
correct
presumably due to buf_size being signed causing GCC to fail to
see that buf_size can't become negative.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In certain circumstances, we can get an oops from a torn down device.
Most notably this is from CD roms trying to call scsi_ioctl. The root
cause of the problem is the fact that after scsi_remove_device() has
been called, the queue is fully torn down. This is actually wrong
since the queue can be used until the sdev release function is called.
Therefore, we add an extra reference to the queue which is released in
sdev->release, so the queue always exists.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Fix kernel-doc warnings in scsi_proc.c:
Warning(drivers/scsi/scsi_proc.c:390): No description found for parameter 'dev'
Warning(drivers/scsi/scsi_proc.c:390): No description found for parameter 'data'
Warning(drivers/scsi/scsi_proc.c:390): Excess function parameter 's' description in 'always_match'
Warning(drivers/scsi/scsi_proc.c:390): Excess function parameter 'p' description in 'always_match'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend BSG infrastructure and add link diagnostics:
- Removed unnecessary copies in handling pass-through mbox cmds.
- Add embedded SLI_CONFIG support for BSG.
- Add multibuffer support.
- Implemented the setting up and tearing down Lancer FC device for performing
internal and external loopback diagnostic tests.
- Implemented the driver support for performing new link diagnostic tests
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
