Use wait_drive_not_busy() in drive_cmd_intr().
v2:
* Fix wait_drive_not_busy() comment (noticed by Sergei).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
task_end_request() modified to always call ide_end_drive_cmd()
for taskfile requests. Previously, ide_end_drive_cmd() was
called only when IDE_TFLAG_FLAGGED was set. Also,
ide_dma_intr() is modified to use task_end_request().
Enables TASKFILE ioctls to get valid register outputs on
successful completion.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_{HOB,TF,DEVICE} defines.
* Set IDE_TFLAG_IN_* flags in {do_rw,ide_no_data,ide_raw}_taskfile() users.
* Remove no longer needed ->tf_flags setup from ide_end_drive_cmd().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Check for DRQ bit being cleared on the final status check.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide_dump_status() may set HOB bit before ide_end_drive_cmd() is called.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
In ide_taskfile_ioctl(), there was a race condition involving
drive->io_32bit. It was cleared and restored during ioctl
requests but there was no synchronization with other requests.
So, other requests could execute with the altered ->io_32bit
setting or updated drive->io_32bit could be overwritten by
ide_taskfile_ioctl().
This patch adds IDE_TFLAG_IO_16BIT flag to indicate to
ide_pio_datablock() that 16-bit I/O is needed regardless of
drive->io_32bit settting.
Bart:
- ported it over recent IDE changes
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This belongs to user-space (and only if really needed).
text data bss dec hex filename
3874 180 28 4082 ff2 drivers/ide/pci/cmd64x.o.before
2231 180 0 2411 96b drivers/ide/pci/cmd64x.o.after
Additionaly to being bloat the code reported incorrect UDMA modes for
the reserved values of UDIDETCR0/1 registers.
Also while at it remove unused CNTRL_DIS_RA0/1 defines.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove broken disk byte-swapping support:
- it can cause a data corruption on SMP (or if using PREEMPT on UP)
- all data coming from disk are byte-swapped by taskfile_*_data() which
results in incorrect identify data being reported by /proc/ide/ and IOCTLs
- "hdx=bswap/byteswap" kernel parameter has been broken on m68k host drivers
(including Atari/Q40 ones) since 2.5.x days (because of 'hwif' zero-ing)
- byte-swapping is limited to PIO transfers (for working with TiVo disks on
x86 machines using user-space solutions or dm-byteswap should result in
much better performance because DMA can be used)
For previous discussions please see:
http://www.ussg.iu.edu/hypermail/linux/kernel/0201.0/0768.htmlhttp://lkml.org/lkml/2004/2/28/111
[ I have dm-byteswap device mapper target if somebody is interested
(patch is for 2.6.4 though but I'll dust it off if needed). ]
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_busy_sleep() helper and use it in do_probe(),
enable_nest() and probe_hwif().
As a nice side-effect this fixes a minor bug in do_probe()
(the code was reading status register without any delay).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Print banner message once per controller in m68k host drivers.
* Change printk() level to KERN_INFO in buddha, falconide and gayle.
* Add banner message to q40ide.
This is basically a preparation for the future IDE layer changes.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move setting hwif->sg_max_nents from pmac_ide_setup_device()
to pmac_ide_setup_dma().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move setting hwif->gendev.parent from ide_pci_setup_ports()
to ide_hwif_configure().
* Always set hwif->io_ports in ide_hwif_configure().
* Use ide_init_port_hw() in ide_hwif_configure().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* ide_init_hwif_ports() call in setup-pci.c::ide_hwif_configure()
doesn't depend on the default cotrol register offset, default IRQ
or ppc_ide_md.ide_init_hwif implementations so ide_std_init_ports()
can always be used.
* Since 'base' is always non-zero and thus hwif->io_ports[IDE_DATA_OFFSET]
is also non-zero always clear hwif->noprobe.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* hwif->hold is always set in au_ide_probe() (few lines earlier),
no need to set it again
* hwif->{channel,select_data,config_data} should be always zero
* autotune PIO also if CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA is defined
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make remaining built-in only IDE host drivers modular, add ide-scan-pci.c
file for probing PCI host drivers registered with IDE core (special case
for built-in IDE and CONFIG_IDEPCI_PCIBUS_ORDER=y) and then take care of
the ordering in which all IDE host drivers are probed when IDE is built-in
during link time.
* Move probing of gayle, falconide, macide, q40ide and buddha (m68k arch
specific) host drivers, before PCI ones (no PCI on m68k), ide-cris (cris
arch specific), cmd640 (x86 arch specific) and pmac (ppc arch specific).
* Move probing of ide-cris (cris arch specific) host driver before cmd640
(x86 arch specific).
* Move probing of mpc8xx (ppc specific) host driver before ide-pnp (depends
on ISA and none of ppc platform that use mpc8xx supports ISA) and ide-h8300
(h8300 arch specific).
* Add "probe_vlb" kernel parameter to cmd640 host driver and update
Documentation/ide.txt accordingly.
* Make IDE_ARM config option visible so it can also be disabled if needed.
* Remove bogus comment from ide.c while at it.
v2:
* Fix two issues spotted by Sergei:
- replace ENOMEM error value by ENOENT in ide-h8300 host driver
- fix MODULE_PARM_DESC() in cmd640 host driver
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add mpc8xx_ide_probe() to mpc8xx.c and call it from probe_for_hwifs().
* Convert ide_arm, ide-cris, ide-h8300, ide-pnp, buddha, falconide, gayle,
macide, q40ide, cmd640 and mpc8xx host drivers to use ide_device_add().
This removes dependency on ide_generic for these drivers so update
ide/Kconfig accordingly.
v2:
* ide_arm build fix (s/ide_device_idx/ide_device_add/)
(Thanks to Christoph Lameter <clameter@sgi.com> for reporting the problem).
Cc: Mikael Starvik <starvik@axis.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_init_port_data() call from ide_arm_init() and move
ide_arm_init() call from init_ide_data() to ide_init().
This patch is a preparation for the future changes (and as a side-effect
makes obsolete "idex=io[,ctl[,irq]]" kernel parameters work for ide_arm).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_init_port_hw() helper.
* rapide.c: convert rapide_locate_hwif() to rapide_setup_ports()
and use ide_init_port_hw().
* ide_platform.c: convert plat_ide_locate_hwif() to plat_ide_setup_ports()
and use ide_init_port_hw().
* sgiioc4.c: use ide_init_port_hw().
* pmac.c: add 'hw_regs_t *hw' argument to pmac_ide_setup_device(),
setup 'hw' in pmac_ide_{macio,pci}_attach() and use ide_init_port_hw()
in pmac_ide_setup_device().
This patch is a preparation for the future changes in the IDE probing code.
There should be no functionality changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Jeremy Higdon <jeremy@sgi.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix build break of powerpc holly_defconfig:
In file included from arch/powerpc/platforms/embedded6xx/holly.c:24:
include/linux/ide.h:1206: error: 'CONFIG_IDE_MAX_HWIFS' undeclared here (not in a function)
There's no need to have a sized array in the prototype, might as well
turn it into a pointer.
It could probably be argued that large parts of the include file can be
covered under #ifdef CONFIG_IDE, but that's a larger undertaking.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename ide_device_add() to ide_device_add_all() and make it accept
'u8 idx[MAX_HWIFS]' instead of 'u8 idx[4]' as an argument.
* Add ide_device_add() wrapper for ide_device_add_all().
* Convert ide_generic_init() to use ide_device_add_all().
* Remove no longer needed ideprobe_init().
There should be no functionality changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add hwif->chipset fixup identical to the one in ideprobe_init()
to ide_device_add().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->chipset should be set if the hwif is claimed by host driver.
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
hwif->chipset should be set if the hwif is claimed by host driver.
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After hwif_register_devices() IDE devices are ready to be used so
the way in which ide_device_add() works currently is racy for hosts
with serialized / IRQ sharing interfaces.
Fix ide_device_add() by looping over interfaces for probe_hwif(),
hwif_init() and hwif_register_devices() operations.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Host drivers using ide_register_hw() and 'initializing == 1':
* ide-pnp
- depends on ISA
* ide_arm
- ARM arch specific
- initialized before all other host drivers
* ide-cris
- CRIS arch specific => IDE_ARCH_OBSOLETE_INIT is not defined
- broken
* ide-h8300
- H8300 arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI
* buddha/q40/gayle/macide/falconide
- M68K arch specific => IDE_ARCH_OBSOLETE_INIT is not defined, no PCI
Since the only host drivers which probe interfaces before the above ones are:
* ali14xx/dtc2278/ht6560b/qd65xx/umc8672
- depend on ISA
- require IDE_ARCH_OBSOLETE_INIT=y to work
* PCI ones
- depend on PCI
don't try to unregister interfaces if 'initializing == 1' in ide_register_hw()
(it is possible that built-in host drivers will claim all IDE interfaces but
later ide-pnp host driver will try to unregister them - this change fixes it).
Also skip hwif->hold check if 'initializing == 1' since it is set only by:
* pmac
- PPC && PMAC specific => no ISA
* au1xxx-ide
- MIPS && SOC_AU1200 specific => no ISA
and use ide_find_port() helper to find free ide_hwifs[] slot.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Assign drive->quirk_list in ->quirkproc implementations:
- hpt366.c::hpt3xx_quirkproc()
- pdc202xx_new.c::pdcnew_quirkproc()
- pdc202xx_old.c::pdc202xx_quirkproc()
* Make ->quirkproc void.
* Move calling ->quirkproc from do_identify() to probe_hwif().
* Convert it821x_fixups() to it821x_quirkproc() in it821x.c.
* Convert siimage_fixup() to sil_quirkproc() in siimage.c, also remove
no longer needed drive->present check from is_dev_seagate_sata().
* Convert ide_undecoded_slave() to accept 'drive' instead of 'hwif'
as an argument. Then convert ide_register_hw() to accept 'quirkproc'
argument instead of 'fixup' one.
* Remove no longer needed ->fixup method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge ->dma_host_{on,off} methods into ->dma_host_set method
which takes 'int on' argument.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Rename cris_dma_{on,off}() to cris_dma_host_{on,off}().
* Remove no longer needed ->dma_off_quietly
(IDE core has the needed code now).
* Make cris_dma_host_on() void.
I left fixing ide-cris after "kill dma_on/dma_off_quietly() methods"
patch because:
* Currently this driver is broken: cris_dma_on() (returns 'int')
is assigned to hwif->dma_host_on (returns 'void') so the driver
won't build.
* ->ide_dma_on method was missing so the driver OOPS-es on attempt
to enable DMA.
* drive->using_dma was never set/cleared so DMA wouldn't be used anyway.
Unfortunately it seems that ide-cris stays broken even after this patch:
* V10: <asm/arch-v10/ide.h> needs fixing
- ide_init_default_hwifs() should be removed
(IDE core no longer uses it)
- same for ide_init_hwif_ports() and ide_default_{irq,io_base}()
(they shouldn't be needed for ide-cris host driver)
* V32: I'm unable to find a place which defines ETRAX_ARCH_V32
but I'm leaving fixing this to CRIS gurus. :)
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_dma_off_quietly() and __ide_dma_on() always available.
* Drop "__" prefix from __ide_dma_on().
* Check for presence of ->dma_host_on instead of ->ide_dma_on.
* Convert all users of ->ide_dma_on and ->dma_off_quietly methods
to use ide_dma_on() and ide_dma_off_quietly() instead.
* Remove no longer needed ->ide_dma_on and ->dma_off_quietly methods
from ide_hwif_t.
* Make ide_dma_on() void.
There should be no functionality changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Since there is no PCI device there should be no functionality
changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Since there is no PCI device there should be no functionality
changes caused by this patch.
Cc: Russell King <rmk@arm.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_toggle_bounce() call to ->ide_dma_on/->dma_off_quietly
methods so they match generic __ide_dma_on()/ide_dma_off_quietly().
Tested on Altix by Jeremy.
Acked-by: Jeremy Higdon <jeremy@sgi.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix SWDMA/MWDMA masks in cy82c693_chipset.
* Add IDE_HFLAG_CY82C693 host flag and use it in ide_tune_dma() to
check whether the DMA should be enabled even if ide_max_dma_mode()
fails.
* Convert cy82c693_dma_enable() to become cy82c693_set_dma_mode()
and remove no longer needed cy82c693_ide_dma_on(). Then set
IDE_HFLAG_CY82C693 instead of IDE_HFLAG_TRUST_BIOS_FOR_DMA in
cy82c693_chipset.
* Bump driver version.
As a result of this patch cy82c693 driver will configure and use DMA on
all SWDMA0-2 and MWDMA0-2 capable ATA devices instead of relying on BIOS.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Mask device DMA masks by ATA_{S,M}WDMA2 in cy82c693_ide_dma_on().
* Remove clipping of DMA modes by id->tDMA in cy82c693_dma_enable():
- id->tDMA may not be defined on newer devices
- id->vendor6/id->tDMA word is in LE endianness
(cy82c693 seems to be Alpha specific though)
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
