Move cma.c's internal definition of enum cma_state to enum rdma_cm_state
in an exported header so that it can be exported via RDMA netlink.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add basic RDMA netlink infrastructure that allows for registration of
RDMA clients for which data is to be exported and supplies message
construction callbacks.
Signed-off-by: Nir Muchtar <nirm@voltaire.com>
[ Reorganize a few things, add CONFIG_NET dependency. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the revision field of
struct pci_dev.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The IW_CM_EVENT_STATUS_xxx values were used in only a couple of places;
cma.c uses -Exxx values instead, and so do the amso1100, cxgb3 and cxgb4
drivers -- only nes was using the enum values (with the mild consequence
that all nes connection failures were treated as generic errors rather
than reported as timeouts or rejections).
We can fix this confusion by getting rid of enum iw_cm_event_status and
using a plain int for struct iw_cm_event.status, and converting nes to
use -Exxx as the other iWARP drivers do.
This also gets rid of the warning
drivers/infiniband/core/cma.c: In function 'cma_iw_handler':
drivers/infiniband/core/cma.c:1333:3: warning: case value '4294967185' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1336:3: warning: case value '4294967186' not in enumerated type 'enum iw_cm_event_status'
drivers/infiniband/core/cma.c:1332:3: warning: case value '4294967192' not in enumerated type 'enum iw_cm_event_status'
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-by: Faisal Latif <faisal.latif@intel.com>
Commit 44c10138fd ("PCI: Change all drivers to use pci_device->revision")
already converted this driver to using the revision field of struct
pci_dev but commit bb9171448d ("IB/ipath: Misc changes to prepare
for IB7220 introduction") later reverted that change for some strange
reason. Restore the change.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The time limit test now correctly checks against current jiffies to
avoid the hang.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A few more EEH fixes:
c4iw_wait_for_reply(): detect fatal EEH condition on timeout and
return an error.
The iw_cxgb4 driver was only calling ib_deregister_device() on an EEH
event followed by a ib_register_device() when the device was
reinitialized. However, the RDMA core doesn't allow multiple
iterations of register/deregister by the provider. See
drivers/infiniband/core/sysfs.c: ib_device_unregister_sysfs() where
the kobject ref is held until the device is deallocated in
ib_deallocate_device(). Calling deregister adds this kobj reference,
and then a subsequent register call will generate a WARN_ON() from the
kobject subsystem because the kobject is being initialized but is
already initialized with the ref held.
So the provider must deregister and dealloc when resetting for an EEH
event, then alloc/register to re-initialize. To do this, we cannot
use the device ptr as our ULD handle since it will change with each
reallocation. This commit adds a ULD context struct which is used as
the ULD handle, and then contains the device pointer and other state
needed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver was never really waiting for RDMA_WR/FINI completions
because the condition variable used to determine if the completion
happened was never reset, and this condition variable is reused for
both connection setup and teardown. This causes various driver
crashes under heavy loads due to releasing resources too early.
The fix is to use atomic bits to correctly reset the condition
immediately after the completion is detected.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Parens are missing: '|' has a higher presedence than '?'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
c4iw_uld_add() must return ERR_PTR() values instead of NULL on failure.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Concurrent ingress CLOSE and ULP ABORT operations causes a crash due
to a race condition where the close path releases the EP lock and then
tries to move the QP state to CLOSED. This must be done inside the EP
lock to avoid the race.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Lustre requires that clients bind to a privileged port number before
connecting to a remote server. On larger clusters (typically more
than about 1000 nodes), the number of privileged ports is exhausted,
resulting in lustre being unusable.
To handle this, we add support for reusable addresses to the rdma_cm.
This mimics the behavior of the socket option SO_REUSEADDR. A user
may set an rdma_cm_id to reuse an address before calling
rdma_bind_addr() (explicitly or implicitly). If set, other
rdma_cm_id's may be bound to the same address, provided that they all
have reuse enabled, and there are no active listens.
If rdma_listen() is called on an rdma_cm_id that has reuse enabled, it
will only succeed if there are no other id's bound to that same
address. The reuse option is exported to user space. The behavior of
the kernel reuse implementation was verified against that given by
sockets.
This patch is derived from a path by Ira Weiny <weiny2@llnl.gov>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
cma_use_port() assumes that the sockaddr is an IPv4 address. Since
IPv6 addressing is supported (and also to support other address
families) make the code more generic in its address handling.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
route: Take the right src and dst addresses in ip_route_newports
ipv4: Fix nexthop caching wrt. scoping.
ipv4: Invalidate nexthop cache nh_saddr more correctly.
net: fix pch_gbe section mismatch warning
ipv4: fix fib metrics
mlx4_en: Removing HW info from ethtool -i report.
net_sched: fix THROTTLED/RUNNING race
drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region
drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region
bonding: fix rx_handler locking
myri10ge: fix rmmod crash
mlx4_en: updated driver version to 1.5.4.1
mlx4_en: Using blue flame support
mlx4_core: reserve UARs for userspace consumers
mlx4_core: maintain available field in bitmap allocator
mlx4: Add blue flame support for kernel consumers
mlx4_en: Enabling new steering
mlx4: Add support for promiscuous mode in the new steering model.
mlx4: generalization of multicast steering.
mlx4_en: Reporting HW revision in ethtool -i
...
Commit 1765a57533 ("net: make dev->master general") introduced a
test of an uninitialized netdev. Fix the code so the intended netdev
is tested.
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Increase DMA max_segment_size on Mellanox hardware
IB/mad: Improve an error message so error code is included
RDMA/nes: Don't print success message at level KERN_ERR
RDMA/addr: Fix return of uninitialized ret value
IB/srp: try to use larger FMR sizes to cover our mappings
IB/srp: add support for indirect tables that don't fit in SRP_CMD
IB/srp: rework mapping engine to use multiple FMR entries
IB/srp: allow sg_tablesize to be set for each target
IB/srp: move IB CM setup completion into its own function
IB/srp: always avoid non-zero offsets into an FMR
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, each device is assumed to be able only handle 64 KB chunks
during DMA. By giving the segment size a larger value, the block layer
will coalesce more S/G entries together for SRP, allowing larger
requests with the same sg_tablesize setting. The block layer is the
only direct user of it, though a few IOMMU drivers reference it as
well for their *_map_sg coalescing code. pci-gart_64 on x86, and a
smattering on on sparc, powerpc, and ia64.
Since other IB protocols could potentially see larger segments with
this, let's check those:
- iSER is fine, because you limit your maximum request size to 512
KB, so we'll never overrun the page vector in struct iser_page_vec
(128 entries currently). It is independent of the DMA segment size,
and handles multi-page segments already.
- IPoIB is fine, as it maps each page individually, and doesn't use
ib_dma_map_sg().
- RDS appears to do the right thing and has no dependencies on DMA
segment size, but I don't claim to have done a complete audit.
- NFSoRDMA and 9p are OK -- they do not use ib_dma_map_sg(), so they
doesn't care about the coalescing.
- Lustre's ko2iblnd does not care about coalescing -- it properly
walks the returned sg list.
This patch ups the value on Mellanox hardware to 1 GB, which matches
reported firmware limits on mlx4.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There's no reason to print "NetEffect RNIC driver successfully loaded"
at level KERN_ERR (where it will uglify the console on a quiet boot).
Change it to KERN_INFO.
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (55 commits)
KVM: unbreak userspace that does not sets tss address
KVM: MMU: cleanup pte write path
KVM: MMU: introduce a common function to get no-dirty-logged slot
KVM: fix rcu usage in init_rmode_* functions
KVM: fix kvmclock regression due to missing clock update
KVM: emulator: Fix permission checking in io permission bitmap
KVM: emulator: Fix io permission checking for 64bit guest
KVM: SVM: Load %gs earlier if CONFIG_X86_32_LAZY_GS=n
KVM: x86: Remove useless regs_page pointer from kvm_lapic
KVM: improve comment on rcu use in irqfd_deassign
KVM: MMU: remove unused macros
KVM: MMU: cleanup page alloc and free
KVM: MMU: do not record gfn in kvm_mmu_pte_write
KVM: MMU: move mmu pages calculated out of mmu lock
KVM: MMU: set spte accessed bit properly
KVM: MMU: fix kvm_mmu_slot_remove_write_access dropping intermediate W bits
KVM: Start lock documentation
KVM: better readability of efer_reserved_bits
KVM: Clear async page fault hash after switching to real mode
KVM: VMX: Initialize vm86 TSS only once.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Commit b23dd4fe42 ("ipv4: Make output route lookup return rtable
directly") resulted in leaving ret uninitialized, where it may later
be returned.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In most cases, get_user_pages and get_user_pages_fast should be used
to pin user pages in memory. But sometimes, some special flags except
FOLL_GET, FOLL_WRITE and FOLL_FORCE are needed, for example in
following patch, KVM needs FOLL_HWPOISON. To support these users,
__get_user_pages is exported directly.
There are some symbol name conflicts in infiniband driver, fixed them too.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Michel Lespinasse <walken@google.com>
CC: Roland Dreier <roland@kernel.org>
CC: Ralph Campbell <infinipath@qlogic.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
Now that we can get larger SG lists, we can take advantage of HCAs that
allow us to use larger FMR sizes. In many cases, we can use up to 512
entries, so start there and work our way down.
Signed-off-by: David Dillow <dillowda@ornl.gov>
This allows us to guarantee the ability to submit up to 8 MB requests
based on the current value of SCSI_MAX_SG_CHAIN_SEGMENTS. While FMR will
usually condense the requests into 8 SG entries, it is imperative that
the target support external tables in case the FMR mapping fails or is
not supported.
We add a safety valve to allow targets without the needed support to
reap the benefits of the large tables, but fail in a manner that lets
the user know that the data didn't make it to the device. The user must
add "allow_ext_sg=1" to the target parameters to indicate that the
target has the needed support.
If indirect_sg_entries is not specified in the modules options, then
the sg_tablesize for the target will default to cmd_sg_entries unless
overridden by the target options.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Instead of forcing all of the S/G entries to fit in one FMR, and falling
back to indirect descriptors if that fails, allow the use of as many
FMRs as needed to map the request. This lays the groundwork for allowing
indirect descriptor tables that are larger than can fit in the command
IU, but should marginally improve performance now by reducing the number
of indirect descriptors needed.
We increase the minimum page size for the FMR pool to 4K, as larger
pages help increase the coverage of each FMR, and it is rare that the
kernel would send down a request with scattered 512 byte fragments.
This patch also move some of the target initialization code afte the
parsing of options, to keep it together with the new code that needs to
allocate memory based on the options given.
Signed-off-by: David Dillow <dillowda@ornl.gov>
Different configurations of target software allow differing max sizes of
the command IU. Allowing this to be changed per-target allows all
targets on an initiator to get an optimal setting.
We deprecate srp_sg_tablesize and replace it with cmd_sg_entries in
preparation for allowing more indirect descriptors than can fit in the
IU.
Signed-off-by: David Dillow <dillowda@ornl.gov>
It is unclear exactly how this code works around Mellanox SRP targets,
or if the problem is on the target side or in the HCA itself. In an
abundance of caution, we should always enable the workaround.
Signed-off-by: David Dillow <dillowda@ornl.gov>
rdma_destroy_id currently uses the global rdma cm 'lock' to test if an
rdma_cm_id has been bound to a device. This prevents an active
address resolution callback handler from assigning a device to the
rdma_cm_id after rdma_destroy_id checks for one.
Instead, we can replace the use of the global lock around the check to
the rdma_cm_id device pointer by setting the id state to destroying,
then flushing all active callbacks. The latter is accomplished by
acquiring and releasing the handler_mutex. Any active handler will
complete first, and any newly scheduled handlers will find the
rdma_cm_id in an invalid state.
In addition to optimizing the current locking scheme, the use of the
rdma_cm_id mutex is a more intuitive synchronization mechanism than
that of the global lock. These changes are based on feedback from
Doug Ledford <dledford@redhat.com> while he was trying to debug a
crash in the rdma cm destroy path.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This problem was reported by Moni Shoua <monis@mellanox.com> and Amir
Vadai <amirv@mellanox.com>:
When destroying a cm_id from a context of a work queue and if
the lap_state of this cm_id is IB_CM_LAP_SENT, we need to
release the reference of this id that was taken upon the send
of the LAP message. Otherwise, if the expected APR message
gets lost, it is only after a long time that the reference
will be released, while during that the work handler thread is
not available to process other things.
It turns out that we need to cancel any pending LAP messages whenever
we transition out of the IB_CM_ESTABLISH state. This occurs when
disconnecting - either sending or receiving a DREQ. It can also
happen in a corner case where we receive a REJ message after sending
an RTU, followed by a LAP. Add checks and cancel any outstanding LAP
messages in these three cases.
Canceling the LAP when sending a DREQ fixes the destroy problem
reported by Moni. When a cm_id is destroyed in the IB_CM_ESTABLISHED
state, it sends a DREQ to the remote side to notify the peer that the
connection is going away.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When processing a SIDR REQ, the ib_cm allocates a new cm_id. The
refcount of the cm_id is initialized to 1. However, cm_process_work
will decrement the refcount after invoking all callbacks. The result
is that the cm_id will end up with refcount set to 0 by the end of the
sidr req handler.
If a user tries to destroy the cm_id, the destruction will proceed,
under the incorrect assumption that no other threads are referencing
the cm_id. This can lead to a crash when the cm callback thread tries
to access the cm_id.
This problem was noticed as part of a larger investigation with kernel
crashes in the rdma_cm when running on a real time OS.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Doug Ledford and Red Hat reported a crash when running the rdma_cm on
a real-time OS. The crash has the following call trace:
cm_process_work
cma_req_handler
cma_disable_callback
rdma_create_id
kzalloc
init_completion
cma_get_net_info
cma_save_net_info
cma_any_addr
cma_zero_addr
rdma_translate_ip
rdma_copy_addr
cma_acquire_dev
rdma_addr_get_sgid
ib_find_cached_gid
cma_attach_to_dev
ucma_event_handler
kzalloc
ib_copy_ah_attr_to_user
cma_comp
[ preempted ]
cma_write
copy_from_user
ucma_destroy_id
copy_from_user
_ucma_find_context
ucma_put_ctx
ucma_free_ctx
rdma_destroy_id
cma_exch
cma_cancel_operation
rdma_node_get_transport
rt_mutex_slowunlock
bad_area_nosemaphore
oops_enter
They were able to reproduce the crash multiple times with the
following details:
Crash seems to always happen on the:
mutex_unlock(&conn_id->handler_mutex);
as conn_id looks to have been freed during this code path.
An examination of the code shows that a race exists in the request
handlers. When a new connection request is received, the rdma_cm
allocates a new connection identifier. This identifier has a single
reference count on it. If a user calls rdma_destroy_id() from another
thread after receiving a callback, rdma_destroy_id will proceed to
destroy the id and free the associated memory. However, the request
handlers may still be in the process of running. When control returns
to the request handlers, they can attempt to access the newly created
identifiers.
Fix this by holding a reference on the newly created rdma_cm_id until
the request handler is through accessing it.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Doug Ledford <dledford@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the M_Key field in SubnGet and SugnGetResp MADs based on correctly
interpreting the protection level specified in the M_KeyProtBits field.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For active and far-EQ cables use an LE2 value of 0 for improved SI.
Signed-off-by: Mitko Haralanov <mitko@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Show whether the SQ is in onchip memory or not.
- Dump both SQ and RQ QIDs.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This at least kicks the user mode applications that are watching for
device events.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the ULP mode for initial RDMA connection setup to the proper DDP
mode. This avoids wasting some HW resources while in streaming mode.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
