Multiple backchannels can share the same tcp connection; from rfc 5661 section
2.10.3.1:
A connection's association with a session is not exclusive. A
connection associated with the channel(s) of one session may be
simultaneously associated with the channel(s) of other sessions
including sessions associated with other client IDs.
However, multiple backchannels share a connection, they must all share
the same xid stream (hence the same rpc_xprt); the only way we have to
match replies with calls at the rpc layer is using the xid.
So, keep the rpc_xprt around as long as the connection lasts, in case
we're asked to use the connection as a backchannel again.
Requests to create new backchannel clients over a given server
connection should results in creating new clients that reuse the
existing rpc_xprt.
But to start, just reject attempts to associate multiple rpc_xprt's with
the same underlying bc_xprt.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
This seems obviously transport-level information even if it's currently
used only by the server socket code.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
* 'for-2.6.37' of git://linux-nfs.org/~bfields/linux: (99 commits)
svcrpc: svc_tcp_sendto XPT_DEAD check is redundant
svcrpc: no need for XPT_DEAD check in svc_xprt_enqueue
svcrpc: assume svc_delete_xprt() called only once
svcrpc: never clear XPT_BUSY on dead xprt
nfsd4: fix connection allocation in sequence()
nfsd4: only require krb5 principal for NFSv4.0 callbacks
nfsd4: move minorversion to client
nfsd4: delay session removal till free_client
nfsd4: separate callback change and callback probe
nfsd4: callback program number is per-session
nfsd4: track backchannel connections
nfsd4: confirm only on succesful create_session
nfsd4: make backchannel sequence number per-session
nfsd4: use client pointer to backchannel session
nfsd4: move callback setup into session init code
nfsd4: don't cache seq_misordered replies
SUNRPC: Properly initialize sock_xprt.srcaddr in all cases
SUNRPC: Use conventional switch statement when reclassifying sockets
sunrpc/xprtrdma: clean up workqueue usage
sunrpc: Turn list_for_each-s into the ..._entry-s
...
Fix up trivial conflicts (two different deprecation notices added in
separate branches) in Documentation/feature-removal-schedule.txt
The source address field in the transport's sock_xprt is initialized
ONLY IF the RPC application passed a pointer to a source address
during the call to rpc_create(). However, xs_bind() subsequently uses
the value of this field without regard to whether the source address
was initialized during transport creation or not.
So far we've been lucky: the uninitialized value of this field is
zeroes. xs_bind(), until recently, used only the sin[6]_addr field in
this sockaddr, and all zeroes is a valid value for this: it means
ANYADDR. This is a happy coincidence.
However, xs_bind() now wants to use the sa_family field as well, and
expects it to be initialized to something other than zero.
Therefore, the source address sockaddr field should be fully
initialized at transport create time in _every_ case, not just when
the RPC application wants to use a specific bind address.
Bruce added a workaround for this missing initialization by adjusting
commit 6bc9638a, but the "right" way to do this is to ensure that the
source address sockaddr is always correctly initialized from the
get-go.
This patch doesn't introduce a behavior change. It's simply a
clean-up of Bruce's fix, to prevent future problems of this kind. It
may look like overkill, but
a) it clearly documents the default initial value of this field,
b) it doesn't assume that the sockaddr_storage memory is first
initialized to any particular value, and
c) it will fail verbosely if some unknown address family is passed
in
Originally introduced by commit d3bc9a1d.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Clean up.
Defensive coding: If "family" is ever something that is neither
AF_INET nor AF_INET6, xs_reclassify_socket6() is not the appropriate
default action. Choose to do nothing in that case.
Introduced by commit 6bc9638a.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Since the xprt in question is forcibly set to be bound the else
branch of this check is unneeded.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Same for UDP sockets creation paths.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The v4 and the v6 wrappers only pass the respective family
to the xs_tcp_setup_socket. This family can be taken from the
xprt's sockaddr.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Now we have a single socket creation routine and can call it
directly from the setup_socket routines.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
After xs_bind is merged it's easy to merge its callers.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
[bfields@redhat.com: fix address family initialization]
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
There's the only difference betseen the xs_bind4 and the
xs_bind6 - the size of sockaddr structure they use.
Fortunatelly its size can be indirectly get from the transport.
Change since v1:
* use sockaddr_storage instead of sockaddr
* use rpc_set_port instead of manual port assigning
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
[bfields@redhat.com: fix address family initialization]
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Remove now unneeded wrappers that just add type and protocol
to socket creation callback.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Same patch for v6 protocols.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The UDPv4 and TCPv4 socket creation callbacks now look very similar.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Make it look like the TCP sockets creation.
Unfortunately the git diff made the patch look messy :(
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The xs_tcp_reuse_connection takes the xprt only to pass it down
to the xs_abort_connection. The later one can get it from the given
transport itself.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The context is already known in all the sock_create callers.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
The net is known from the xprt_create and this tagging will also
give un the context in the conntection workers where real sockets
are created.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
We have for each socket :
One spinlock (sk_slock.slock)
One rwlock (sk_callback_lock)
Possible scenarios are :
(A) (this is used in net/sunrpc/xprtsock.c)
read_lock(&sk->sk_callback_lock) (without blocking BH)
<BH>
spin_lock(&sk->sk_slock.slock);
...
read_lock(&sk->sk_callback_lock);
...
(B)
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
(C)
spin_lock_bh(&sk->sk_slock)
...
write_lock_bh(&sk->sk_callback_lock)
stuff
write_unlock_bh(&sk->sk_callback_lock)
spin_unlock_bh(&sk->sk_slock)
This (C) case conflicts with (A) :
CPU1 [A] CPU2 [C]
read_lock(callback_lock)
<BH> spin_lock_bh(slock)
<wait to spin_lock(slock)>
<wait to write_lock_bh(callback_lock)>
We have one problematic (C) use case in inet_csk_listen_stop() :
local_bh_disable();
bh_lock_sock(child); // spin_lock_bh(&sk->sk_slock)
WARN_ON(sock_owned_by_user(child));
...
sock_orphan(child); // write_lock_bh(&sk->sk_callback_lock)
lockdep is not happy with this, as reported by Tetsuo Handa
It seems only way to deal with this is to use read_lock_bh(callbacklock)
everywhere.
Thanks to Jarek for pointing a bug in my first attempt and suggesting
this solution.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Fix an Oops in the NFSv4 atomic open code
NFS: Fix the selection of security flavours in Kconfig
NFS: fix the return value of nfs_file_fsync()
rpcrdma: Fix SQ size calculation when memreg is FRMR
xprtrdma: Do not truncate iova_start values in frmr registrations.
nfs: Remove redundant NULL check upon kfree()
nfs: Add "lookupcache" to displayed mount options
NFS: allow close-to-open cache semantics to apply to root of NFS filesystem
SUNRPC: fix NFS client over TCP hangs due to packet loss (Bug 16494)
This is more kernel-ish, saves some space, and also allows us to
expand the ops without breaking all the callers who are happy for the
new members to be NULL.
The few places which defined their own param types are changed to the
new scheme (more which crept in recently fixed in following patches).
Since we're touching them anyway, we change get() and set() to take a
const struct kernel_param (which they really are). This causes some
harmless warnings until we fix them (in following patches).
To reduce churn, module_param_call creates the ops struct so the callers
don't have to change (and casts the functions to reduce warnings).
The modern version which takes an ops struct is called module_param_cb.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: linux-nfs@vger.kernel.org
Cc: netdev@vger.kernel.org
When reusing a TCP connection, ensure that it's aborted if a previous
shutdown attempt has been made on that connection so that the RPC over
TCP recovery mechanism succeeds.
Signed-off-by: Andy Chittenden <andyc.bluearc@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the attempt to read the calldir fails, then instead of storing the read
bytes, we currently discard them. This leads to a garbage final result when
upon re-entry to the same routine, we read the remaining bytes.
Fixes the regression in bugzilla number 16213. Please see
https://bugzilla.kernel.org/show_bug.cgi?id=16213
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Also collect exit code together while we're at it.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
This patch removes from net/ (but not any netfilter files)
all the unnecessary return; statements that precede the
last closing brace of void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems strange to maintain stats for bytes_sent in one structure, and
bytes received in another. Try to assemble all the RPC request-related
stats in struct rpc_rqst
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
It is a BUG for anybody to call this function without setting
args->bc_xprt. Trying to return an error value is just wrong, since the
user cannot fix this: it is a programming error, not a user error.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Compute an RPC request's RTT once, and use that value both for reporting
RPC metrics, and for adjusting the RTT context used by the RPC client's RTT
estimator algorithm.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We should not allow soft tasks to wait for longer than the major timeout
period when waiting for a reconnect to occur.
Remove the field xprt->connect_timeout since it has been obsoleted by
xprt->reestablish_timeout.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This fixes a bug with setting xprt->stat.connect_start.
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The ->release_request() callback was designed to allow the transport layer
to do housekeeping after the RPC call is done. It cannot be used to free
the request itself, and doing so leads to a use-after-free bug in
xprt_release().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: ensure bdi_unregister is called on mount failure.
NFS: Avoid a deadlock in nfs_release_page
NFSv4: Don't ignore the NFS_INO_REVAL_FORCED flag in nfs_revalidate_inode()
nfs4: Make the v4 callback service hidden
nfs: fix unlikely memory leak
rpc client can not deal with ENOSOCK, so translate it into ENOCONN
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
(Applies on top of "Remove uses of NIPQUAD, use %pI4")
Casts to void of snprintf are most uncommon in kernel source.
9 use casts, 1301 do not.
Remove the remaining uses in net/sunrpc/
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally submitted Jan 1, 2010
http://patchwork.kernel.org/patch/71221/
Convert NIPQUAD to the %pI4 format extension where possible
Convert %02x%02x%02x%02x/NIPQUAD to %08x/ntohl
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NFSv4 client send a request before connect, or the old connection was broken
because a ETIMEOUT error catched by call_status, ->send_request will return
ENOSOCK, but rpc layer can not deal with it, so make sure ->send_request can
translate ENOSOCK into ENOCONN.
Signed-off-by: Bian Naimeng <biannm@cn.fujitsu.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This can, for instance, happen if the user specifies a link local IPv6
address.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
xprtsock.c: make bc_{malloc/free} static
The server backchannel buf_alloc and buf_free methods should
be static since they are not used outside this file.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: J. Bruce Fields <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The kernel sometimes makes RPC calls to services that aren't running.
Because the kernel's RPC client always assumes the hard retry semantic
when reconnecting a connection-oriented RPC transport, the underlying
reconnect logic takes a long while to time out, even though the remote
may have responded immediately with ECONNREFUSED.
In certain cases, like upcalls to our local rpcbind daemon, or for NFS
mount requests, we'd like the kernel to fail immediately if the remote
service isn't reachable. This allows another transport to be tried
immediately, or the pending request can be abandoned quickly.
Introduce a per-request flag which controls how call_transmit_status()
behaves when request transmission fails because the server cannot be
reached.
We don't want soft connection semantics to apply to other errors. The
default case of the switch statement in call_transmit_status() no
longer falls through; the fall through code is copied to the default
case, and a "break;" is added.
The transport's connection re-establishment timeout is also ignored for
such requests. We want the request to fail immediately, so the
reconnect delay is skipped. Additionally, we don't want a connect
failure here to further increase the reconnect timeout value, since
this request will not be retried.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For consistency drop & in front of every proc_handler. Explicity
taking the address is unnecessary and it prevents optimizations
like stubbing the proc_handlers to NULL.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Now that sys_sysctl is a compatiblity wrapper around /proc/sys
all sysctl strategy routines, and all ctl_name and strategy
entries in the sysctl tables are unused, and can be
revmoed.
In addition neigh_sysctl_register has been modified to no longer
take a strategy argument and it's callers have been modified not
to pass one.
Cc: "David Miller" <davem@davemloft.net>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
[[resending with correct cc: - "vfs.kernel.org" just isn't right!]]
xprt->reestablish_timeout is used to cause TCP connection attempts to
back off if the connection fails so as not to hammer the network,
but to still allow immediate connections when there is no reason to
believe there is a problem.
It is not used for the first connection (when transport->sock is NULL)
but only on reconnects.
It is currently set:
a/ to 0 when xs_tcp_state_change finds a state of TCP_FIN_WAIT1
on the assumption that the client has closed the connection
so the reconnect should be immediate when needed.
b/ to at least XS_TCP_INIT_REEST_TO when xs_tcp_state_change
detects TCP_CLOSING or TCP_CLOSE_WAIT on the assumption that the
server closed the connection so a small delay at least is
required.
c/ as above when xs_tcp_state_change detects TCP_SYN_SENT, so that
it is never 0 while a connection has been attempted, else
the doubling will produce 0 and there will be no backoff.
d/ to double is value (up to a limit) when delaying a connection,
thus providing exponential backoff and
e/ to XS_TCP_INIT_REEST_TO in xs_setup_tcp as simple initialisation.
So you can see it is highly dependant on xs_tcp_state_change being
called as expected. However experimental evidence shows that
xs_tcp_state_change does not see all state changes.
("rpcdebug -m rpc trans" can help show what actually happens).
Results show:
TCP_ESTABLISHED is reported when a connection is made. TCP_SYN_SENT
is never reported, so rule 'c' above is never effective.
When the server closes the connection, TCP_CLOSE_WAIT and
TCP_LAST_ACK *might* be reported, and TCP_CLOSE is always
reported. This rule 'b' above will sometimes be effective, but
not reliably.
When the client closes the connection, it used to result in
TCP_FIN_WAIT1, TCP_FIN_WAIT2, TCP_CLOSE. However since commit
f75e674 (SUNRPC: Fix the problem of EADDRNOTAVAIL syslog floods on
reconnect) we don't see *any* events on client-close. I think this
is because xs_restore_old_callbacks is called to disconnect
xs_tcp_state_change before the socket is closed.
In any case, rule 'a' no longer applies.
So all that is left are rule d, which successfully doubles the
timeout which is never rest, and rule e which initialises the timeout.
Even if the rules worked as expected, there would be a problem because
a successful connection does not reset the timeout, so a sequence
of events where the server closes the connection (e.g. during failover
testing) will cause longer and longer timeouts with no good reason.
This patch:
- sets reestablish_timeout to 0 in xs_close thus effecting rule 'a'
- sets it to 0 in xs_tcp_data_ready to ensure that a successful
connection resets the timeout
- sets it to at least XS_TCP_INIT_REEST_TO after it is doubled,
thus effecting rule c
I have not reimplemented rule b and the new version of rule c
seems sufficient.
I suspect other code in xs_tcp_data_ready needs to be revised as well.
For example I don't think connect_cookie is being incremented as often
as it should be.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
[sunrpc: change idle timeout value for the backchannel]
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Acked-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
