nla_nest_start may fail and thus deserves a check.
The fix returns -EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Mellanox commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.
ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for
getting mac address.
ncsi_rsp_handler_oem_mlx: This handles response received for all
mellanox OEM commands.
ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the ncsi-netlink interface with two new commands and
three new attributes to configure multiple packages and/or channels at
once, and configure specific failover modes.
NCSI_CMD_SET_PACKAGE mask and NCSI_CMD_SET_CHANNEL_MASK set a whitelist
of packages or channels allowed to be configured with the
NCSI_ATTR_PACKAGE_MASK and NCSI_ATTR_CHANNEL_MASK attributes
respectively. If one of these whitelists is set only packages or
channels matching the whitelist are considered for the channel queue in
ncsi_choose_active_channel().
These commands may also use the NCSI_ATTR_MULTI_FLAG to signal that
multiple packages or channels may be configured simultaneously. NCSI
hardware arbitration (HWA) must be available in order to enable
multi-package mode. Multi-channel mode is always available.
If the NCSI_ATTR_CHANNEL_ID attribute is present in the
NCSI_CMD_SET_CHANNEL_MASK command the it sets the preferred channel as
with the NCSI_CMD_SET_INTERFACE command. The combination of preferred
channel and channel whitelist defines a primary channel and the allowed
failover channels.
If the NCSI_ATTR_MULTI_FLAG attribute is also present then the preferred
channel is configured for Tx/Rx and the other channels are enabled only
for Rx.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the NCSI driver is stopped with ncsi_stop_dev() the channel
monitors are stopped and the state set to "inactive". However the
channels are still configured and active from the perspective of the
network controller. We should suspend each active channel but in the
context of ncsi_stop_dev() the transmit queue has been or is about to be
stopped so we won't have time to do so.
Instead when ncsi_start_dev() is called if the NCSI topology has already
been probed then call ncsi_reset_dev() to suspend any channels that were
previously active. This resets the network controller to a known state,
provides an up to date view of channel link state, and makes sure that
mode flags such as NCSI_MODE_TX_ENABLE are properly reset.
In addition to ncsi_start_dev() use ncsi_reset_dev() in ncsi-netlink.c
to update the channel configuration more cleanly.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The concepts of a channel being 'active' and it having link are slightly
muddled in the NCSI driver. Tweak this slightly so that
NCSI_CHANNEL_ACTIVE represents a channel that has been configured and
enabled, and NCSI_CHANNEL_INACTIVE represents a de-configured channel.
This distinction is important because a channel can be 'active' but have
its link down; in this case the channel may still need to be configured
so that it may receive AEN link-state-change packets.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a package is deselected all channels of that package cease
communication. If there are other channels active on the package of the
suspended channel this will disable them as well, so only send a
deselect-package command if no other channels are active.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the NCSI driver sends a select-package command to all possible
packages simultaneously to discover what packages are available. However
at this stage in the probe process the driver does not know if
hardware arbitration is available: if it isn't then this process could
cause collisions on the RMII bus when packages try to respond.
Update the probe loop to probe each package one by one, and once
complete check if HWA is universally supported.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCSI hardware arbitration allows multiple packages to be enabled at once
and share the same wiring. If the NCSI driver recognises that HWA is
available it unconditionally enables all packages and channels; but that
is a configuration decision rather than something required by HWA.
Additionally the current implementation will not failover on link events
which can cause connectivity to be lost unless the interface is manually
bounced.
Retain basic HWA support but remove the separate configuration path to
enable all channels, leaving this to be handled by a later
implementation.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Broadcom commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.
ncsi_oem_gma_handler_bcm: This handler send NCSI broadcom command for
getting mac address.
ncsi_rsp_handler_oem_bcm: This handles response received for all
broadcom OEM commands.
ncsi_rsp_handler_oem_bcm_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new command (NCSI_CMD_SEND_CMD) is added to allow user space application
to send NC-SI command to the network card.
Also, add a new attribute (NCSI_ATTR_DATA) for transferring request and response.
The work flow is as below.
Request:
User space application
-> Netlink interface (msg)
-> new Netlink handler - ncsi_send_cmd_nl()
-> ncsi_xmit_cmd()
Response:
Response received - ncsi_rcv_rsp()
-> internal response handler - ncsi_rsp_handler_xxx()
-> ncsi_rsp_handler_netlink()
-> ncsi_send_netlink_rsp ()
-> Netlink interface (msg)
-> user space application
Command timeout - ncsi_request_timeout()
-> ncsi_send_netlink_timeout ()
-> Netlink interface (msg with zero data length)
-> user space application
Error:
Error detected
-> ncsi_send_netlink_err ()
-> Netlink interface (err msg)
-> user space application
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM commands and response handling. It also defines OEM
command and response structure as per NCSI specification along with its
handlers.
ncsi_cmd_handler_oem: This is a generic command request handler for OEM
commands
ncsi_rsp_handler_oem: This is a generic response handler for OEM commands
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ncsi_pkg_info_all_nl() .dumpit handler is missing the NLM_F_MULTI
flag, causing additional package information after the first to be lost.
Also fixup a sanity check in ncsi_write_package_info() to reject out of
range package IDs.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves all of the netdev_printk(KERN_DEBUG, ...) messages over to
netdev_dbg.
As Joe explains:
> netdev_dbg is not included in object code unless
> DEBUG is defined or CONFIG_DYNAMIC_DEBUG is set.
> And then, it is not emitted into the log unless
> DEBUG is set or this specific netdev_dbg is enabled
> via the dynamic debug control file.
Which is what we're after in this case.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This does not provide useful information. As the ncsi maintainer said:
> either we get a channel or broadcom has gone out to lunch
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In normal operation we see this series of messages as the host drives
the network device:
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
ftgmac100 1e660000.ethernet eth0: NCSI interface down
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI interface up
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state down
ftgmac100 1e660000.ethernet eth0: NCSI: suspending channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI: channel 0 link down after config
ftgmac100 1e660000.ethernet eth0: NCSI interface down
ftgmac100 1e660000.ethernet eth0: NCSI: LSC AEN - channel 0 state up
ftgmac100 1e660000.ethernet eth0: NCSI: configuring channel 0
ftgmac100 1e660000.ethernet eth0: NCSI interface up
This makes all of these messages netdev_dbg. They are still useful to
debug eg. misbehaving network device firmware, but we do not need them
filling up the kernel logs in normal operation.
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_CC_STACKPROTECTOR enabled the kernel panics as below when
parsing a NCSI_CMD_PKG_INFO command:
[ 150.149711] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
[ 150.149711]
[ 150.159919] CPU: 0 PID: 1301 Comm: ncsi-netlink Not tainted 4.13.16-468cbec6d2c91239332cb91b1f0a73aafcb6f0c6 #1
[ 150.170004] Hardware name: Generic DT based system
[ 150.174852] [<80109930>] (unwind_backtrace) from [<80106bc4>] (show_stack+0x20/0x24)
[ 150.182641] [<80106bc4>] (show_stack) from [<805d36e4>] (dump_stack+0x20/0x28)
[ 150.189888] [<805d36e4>] (dump_stack) from [<801163ac>] (panic+0xdc/0x278)
[ 150.196780] [<801163ac>] (panic) from [<801162cc>] (__stack_chk_fail+0x20/0x24)
[ 150.204111] [<801162cc>] (__stack_chk_fail) from [<805cff08>] (ncsi_pkg_info_all_nl+0x244/0x258)
[ 150.212912] [<805cff08>] (ncsi_pkg_info_all_nl) from [<804f939c>] (genl_lock_dumpit+0x3c/0x54)
[ 150.221535] [<804f939c>] (genl_lock_dumpit) from [<804f873c>] (netlink_dump+0xf8/0x284)
[ 150.229550] [<804f873c>] (netlink_dump) from [<804f8d44>] (__netlink_dump_start+0x124/0x17c)
[ 150.237992] [<804f8d44>] (__netlink_dump_start) from [<804f9880>] (genl_rcv_msg+0x1c8/0x3d4)
[ 150.246440] [<804f9880>] (genl_rcv_msg) from [<804f9174>] (netlink_rcv_skb+0xd8/0x134)
[ 150.254361] [<804f9174>] (netlink_rcv_skb) from [<804f96a4>] (genl_rcv+0x30/0x44)
[ 150.261850] [<804f96a4>] (genl_rcv) from [<804f7790>] (netlink_unicast+0x198/0x234)
[ 150.269511] [<804f7790>] (netlink_unicast) from [<804f7ffc>] (netlink_sendmsg+0x368/0x3b0)
[ 150.277783] [<804f7ffc>] (netlink_sendmsg) from [<804abea4>] (sock_sendmsg+0x24/0x34)
[ 150.285625] [<804abea4>] (sock_sendmsg) from [<804ac1dc>] (___sys_sendmsg+0x244/0x260)
[ 150.293556] [<804ac1dc>] (___sys_sendmsg) from [<804ad98c>] (__sys_sendmsg+0x5c/0x9c)
[ 150.301400] [<804ad98c>] (__sys_sendmsg) from [<804ad9e4>] (SyS_sendmsg+0x18/0x1c)
[ 150.308984] [<804ad9e4>] (SyS_sendmsg) from [<80102640>] (ret_fast_syscall+0x0/0x3c)
[ 150.316743] ---[ end Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: 805cff08
This turns out to be because the attrs array in ncsi_pkg_info_all_nl()
is initialised to a length of NCSI_ATTR_MAX which is the maximum
attribute number, not the number of attributes.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the message be freed immediately, no need to trim it
back to the previous size.
Inspired by commit 7a9b3ec1e1 ("nl80211: remove unnecessary genlmsg_cancel() calls")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently refactored this code and introduced a static checker
warning. Smatch complains that if cmd->index is zero then we would
underflow the arrays. That's obviously true.
The question is whether we prevent cmd->index from being zero at a
different level. I've looked at the code and I don't immediately see
a check for that.
Fixes: 062b3e1b6d ("net/ncsi: Refactor MAC, VLAN filters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI driver defines a generic ncsi_channel_filter struct that can be
used to store arbitrarily formatted filters, and several generic methods
of accessing data stored in such a filter.
However in both the driver and as defined in the NCSI specification
there are only two actual filters: VLAN ID filters and MAC address
filters. The splitting of the MAC filter into unicast, multicast, and
mixed is also technically not necessary as these are stored in the same
location in hardware.
To save complexity, particularly in the set up and accessing of these
generic filters, remove them in favour of two specific structs. These
can be acted on directly and do not need several generic helper
functions to use.
This also fixes a memory error found by KASAN on ARM32 (which is not
upstream yet), where response handlers accessing a filter's data field
could write past allocated memory.
[ 114.926512] ==================================================================
[ 114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58
[ 114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546
[ 114.947593]
[ 114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13
...
[ 115.170233] The buggy address belongs to the object at 94888540
[ 115.170233] which belongs to the cache kmalloc-32 of size 32
[ 115.181917] The buggy address is located 24 bytes inside of
[ 115.181917] 32-byte region [94888540, 94888560)
[ 115.192115] The buggy address belongs to the page:
[ 115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1
[ 115.204200] flags: 0x100(slab)
[ 115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0
[ 115.215444] page dumped because: kasan: bad access detected
[ 115.221036]
[ 115.222544] Memory state around the buggy address:
[ 115.227384] 94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc
[ 115.233959] 94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc
[ 115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.247077] ^
[ 115.252523] 94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc
[ 115.259093] 94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[ 115.265639] ==================================================================
Reported-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to nla_nest_start calls nla_put which can lead to a NULL
return so it's possible for attr to become NULL and we can potentially
get a NULL pointer dereference on attr. Fix this by checking for
a NULL return.
Detected by CoverityScan, CID#1466125 ("Dereference null return")
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two error paths which are missing unlocks in this function.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're supposed to use kfree_skb() to free these sk_buffs.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic netlink family for NCSI. This supports three commands;
NCSI_CMD_PKG_INFO which returns information on packages and their
associated channels, NCSI_CMD_SET_INTERFACE which allows a specific
package or package/channel combination to be set as the preferred
choice, and NCSI_CMD_CLEAR_INTERFACE which clears any preferred setting.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current HNCDSC handler takes the status flag from the AEN packet and
will update or change the current channel based on this flag and the
current channel status.
However the flag from the HNCDSC packet merely represents the host link
state. While the state of the host interface is potentially interesting
information it should not affect the state of the NCSI link. Indeed the
NCSI specification makes no mention of any recommended action related to
the host network controller driver state.
Update the HNCDSC handler to record the host network driver status but
take no other action.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several response handlers return EBUSY if the data corresponding to the
command/response pair is already set. There is no reason to return an
error here; the channel is advertising something as enabled because we
told it to enable it, and it's possible that the feature has been
enabled previously.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI driver is mostly silent which becomes a headache when trying to
determine what has occurred on the NCSI connection. This adds additional
logging in a few key areas such as state transitions and calling out
certain errors more visibly.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/ncsi/ncsi-manage.c:41:5: warning:
symbol 'ncsi_get_filter' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The length of GVI (GetVersionInfo) response packet should be 40 instead
of 36. This issue was found from /sys/kernel/debug/ncsi/eth0/stats.
# ethtool --ncsi eth0 swstats
:
RESPONSE OK TIMEOUT ERROR
=======================================
GVI 0 0 2
With this applied, no error reported on GVI response packets:
# ethtool --ncsi eth0 swstats
:
RESPONSE OK TIMEOUT ERROR
=======================================
GVI 2 0 0
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI channel has been configured to provide service if its link
monitor timer is enabled, regardless of its state (inactive or active).
So the timeout event on the link monitor indicates the out-of-service
on that channel, for which a failover is needed.
This sets NCSI_DEV_RESHUFFLE flag to enforce failover on link monitor
timeout, regardless the channel's original state (inactive or active).
Also, the link is put into "down" state to give the failing channel
lowest priority when selecting for the active channel. The state of
failing channel should be set to active in order for deinitialization
and failover to be done.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are no NCSI channels probed, HWA (Hardware Arbitration)
mode is enabled. It's not correct because HWA depends on the fact:
NCSI channels exist and all of them support HWA mode. This disables
HWA when no channels are probed.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ncsi_channel_monitor() misses stopping the channel monitor in several
places that it should, causing a WARN_ON_ONCE() to trigger when the
monitor is re-started later, eg:
[ 459.040000] WARNING: CPU: 0 PID: 1093 at net/ncsi/ncsi-manage.c:269 ncsi_start_channel_monitor+0x7c/0x90
[ 459.040000] CPU: 0 PID: 1093 Comm: kworker/0:3 Not tainted 4.10.17-gaca2fdd #140
[ 459.040000] Hardware name: ASpeed SoC
[ 459.040000] Workqueue: events ncsi_dev_work
[ 459.040000] [<80010094>] (unwind_backtrace) from [<8000d950>] (show_stack+0x20/0x24)
[ 459.040000] [<8000d950>] (show_stack) from [<801dbf70>] (dump_stack+0x20/0x28)
[ 459.040000] [<801dbf70>] (dump_stack) from [<80018d7c>] (__warn+0xe0/0x108)
[ 459.040000] [<80018d7c>] (__warn) from [<80018e70>] (warn_slowpath_null+0x30/0x38)
[ 459.040000] [<80018e70>] (warn_slowpath_null) from [<803f6a08>] (ncsi_start_channel_monitor+0x7c/0x90)
[ 459.040000] [<803f6a08>] (ncsi_start_channel_monitor) from [<803f7664>] (ncsi_configure_channel+0xdc/0x5fc)
[ 459.040000] [<803f7664>] (ncsi_configure_channel) from [<803f8160>] (ncsi_dev_work+0xac/0x474)
[ 459.040000] [<803f8160>] (ncsi_dev_work) from [<8002d244>] (process_one_work+0x1e0/0x450)
[ 459.040000] [<8002d244>] (process_one_work) from [<8002d510>] (worker_thread+0x5c/0x570)
[ 459.040000] [<8002d510>] (worker_thread) from [<80033614>] (kthread+0x124/0x164)
[ 459.040000] [<80033614>] (kthread) from [<8000a5e8>] (ret_from_fork+0x14/0x2c)
This also updates the monitor instead of just returning if
ncsi_xmit_cmd() fails to send the get-link-status command so that the
monitor properly times out.
Fixes: e6f44ed6d0 "net/ncsi: Package and channel management"
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the value of the HNCDSC AEN packet.
Fixes: 7a82ecf4cf "net/ncsi: NCSI AEN packet handler"
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we drop any new VLAN ids if there are more than the current
(or last used) channel can support. Most importantly this is a problem
if no channel has been selected yet, resulting in a segfault.
Secondly this does not necessarily reflect the capabilities of any other
channels. Instead only drop a new VLAN id if we are already tracking the
maximum allowed by the NCSI specification. Per-channel limits are
already handled by ncsi_add_filter(), but add a message to set_one_vid()
to make it obvious that the channel can not support any more VLAN ids.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a new link error in allmodconfig kernels after ftgmac100
started using the ncsi helpers:
ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
Related to that, we get another error when CONFIG_NET_NCSI is disabled:
drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'?
drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'?
This fixes both problems at once, using a 'static inline' stub helper
for the disabled case, and exporting the functions when they are present.
Fixes: 51564585d8 ("ftgmac100: Support NCSI VLAN filtering when available")
Fixes: 21acf63013 ("net/ncsi: Configure VLAN tag filter")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the ndo_vlan_rx_{add,kill}_vid callbacks to have the NCSI
stack process new VLAN tags and configure the channel VLAN filter
appropriately.
Several VLAN tags can be set and a "Set VLAN Filter" packet must be sent
for each one, meaning the ncsi_dev_state_config_svf state must be
repeated. An internal list of VLAN tags is maintained, and compared
against the current channel's ncsi_channel_filter in order to keep track
within the state. VLAN filters are removed in a similar manner, with the
introduction of the ncsi_dev_state_config_clear_vids state. The maximum
number of VLAN tag filters is determined by the "Get Capabilities"
response from the channel.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves AEN handler for Host Network Controller Driver Status
Change (HNCDSC):
* The channel's lock should be hold when accessing its state.
* Do failover when host driver isn't ready.
* Configure channel when host driver becomes ready.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. C0 is in link-up state while C1 is in link-down
state. C0 is chosen as active channel until unplugging and plugging
C0's cable: On unplugging C0's cable, LSC (Link State Change) AEN
packet received on C0 to report link-down event. After that, C1 is
chosen as active channel. LSC AEN for link-up event is lost on C0
when plugging C0's cable back. We lose the network even C0 is usable.
This resolves the issue by recording the (hot) channel that was ever
chosen as active one. The hot channel is chosen to be active one
if none of available channels in link-up state. With this, C0 is still
the active one after unplugging C0's cable. LSC AEN packet received
on C0 when plugging its cable back.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. Both of them are connected to different LANs,
means they are in link-up state and C0 is chosen as the active one
until resetting BCM5718 happens as below.
Resetting BCM5718 results in LSC (Link State Change) AEN packet
received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet
received on C0 to report link-down, it fails over to C1 because C1
is in link-up state as software can see. However, C1 is in link-down
state in hardware. It means the link state is out of synchronization
between hardware and software, resulting in inappropriate channel (C1)
selected as active one.
This resolves the issue by sending separate GLS (Get Link Status)
commands to all channels in the package before trying to do failover.
The last link states of all channels in the package are retrieved.
With it, C0 (not C1) is selected as active one as expected.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several if/else statements in the state machine implemented
by switch/case in ncsi_suspend_channel() to avoid duplicated code. It
makes the code a bit hard to be understood.
This drops if/else statements in ncsi_suspend_channel() to improve the
code readability as Joel Stanley suggested. Also, it becomes easy to
add more states in the state machine without affecting current code.
No logical changes introduced by this.
Suggested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces ncsi_stop_dev(), as counterpart to ncsi_start_dev(),
to stop the NCSI device so that it can be reenabled in future. This
API should be called when the network device driver is going to
shutdown the device. There are 3 things done in the function: Stop
the channel monitoring; Reset channels to inactive state; Report
NCSI link down.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original NCSI channel monitoring was implemented based on a
backoff algorithm: the GLS response should be received in the
specified interval. Otherwise, the channel is regarded as dead
and failover should be taken if current channel is an active one.
There are several problems in the implementation: (A) On BCM5718,
we found when the IID (Instance ID) in the GLS command packet
changes from 255 to 1, the response corresponding to IID#1 never
comes in. It means we cannot make the unfair judgement that the
channel is dead when one response is missed. (B) The code's
readability should be improved. (C) We should do failover when
current channel is active one and the channel monitoring should
be marked as disabled before doing failover.
This reworks the channel monitoring to address all above issues.
The fields for channel monitoring is put into separate struct
and the state of channel monitoring is predefined. The channel
is regarded alive if the network controller responses to one of
two GLS commands or both of them in 5 seconds.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one NCSI request property for now: the response for
the sent command need drive the workqueue or not. So we had one
field (@driven) for the purpose. We lost the flexibility to extend
NCSI request properties.
This replaces @driven with @flags and @req_flags in NCSI request
and NCSI command argument struct. Each bit of the newly introduced
field can be used for one property. No functional changes introduced.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
