The documentation to configure I3C3/FSI1 and I3C4/FSI2 was initially
unclear.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message, resolve rebase conflicts]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-5-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C function the pin participated in was incorrectly named SDA14
which lead to a failure to mux:
[ 6.884344] No function I2C14 found on pin 7 (7). Found signal(s) MACLINK4, SDA14, GPIOA7 for function(s) MACLINK4, SDA14, GPIOA7
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-4-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins crept in that weren't ordered in the list.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-3-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
Commit 674fa8daa8 ("pinctrl: aspeed-g5: Delay acquisition of regmaps")
was determined to be a partial fix to the problem of acquiring the LPC
Host Controller and GFX regmaps: The AST2500 pin controller may need to
fetch syscon regmaps during expression evaluation as well as when
setting mux state. For example, this case is hit by attempting to export
pins exposing the LPC Host Controller as GPIOs.
An optional eval() hook is added to the Aspeed pinmux operation struct
and called from aspeed_sig_expr_eval() if the pointer is set by the
SoC-specific driver. This enables the AST2500 to perform the custom
action of acquiring its regmap dependencies as required.
John Wang tested the fix on an Inspur FP5280G2 machine (AST2500-based)
where the issue was found, and I've booted the fix on Witherspoon
(AST2500) and Palmetto (AST2400) machines, and poked at relevant pins
under QEMU by forcing mux configurations via devmem before exporting
GPIOs to exercise the driver.
Fixes: 7d29ed88ac ("pinctrl: aspeed: Read and write bits in LPC and GFX controllers")
Fixes: 674fa8daa8 ("pinctrl: aspeed-g5: Delay acquisition of regmaps")
Reported-by: John Wang <wangzqbj@inspur.com>
Tested-by: John Wang <wangzqbj@inspur.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190829071738.2523-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise they look odd in the face of not being listed in the bindings
documents.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190724081313.12934-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2600 pinmux is fairly similar to the previous generations of
ASPEED BMC SoCs in terms of architecture, though differ in some of the
design details. The complexity of the pin expressions is largely reduced
(e.g. there are no-longer signals with multiple expressions muxing them
to the associated pin), and there are now signals and buses with
multiple pin groups.
The driver implements pinmux support for all 244 GPIO-capable pins plus
a further four pins that are not GPIO capable but which expose multiple
signals. pinconf will be implemented in a follow-up patch.
The implementation has been smoke-tested under qemu, and run on hardware
by ASPEED.
Debugged-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190711041942.23202-7-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2400 and AST2500 SoCs only exposed one pin group per function.
Lone pin groups drove some implementation simplifications in the ASPEED
pinmux infrastructure that is now invalid for the AST2600, which
supports multiple groups per function for some functions on the chip
(SMBus Alert pins and UARTs among others).
This patch reworks the macro jungle to enable support for multiple pin
groups. In the process we inflict some collateral damage on the existing
AST2400 and AST2500 drivers, but the rework is mostly a relatively
straight-forward, automated transform of adding the pin name as an
argument to some macro calls and implementing wrappers to paper over
groups in the cases where there aren't multiple.
As previously documented, the macro infrastructure exposes mux
configuration as symbols in the source file which are used to detect
accidental duplication. Previously these symbols were named in terms of
the signal for a given expression. As the AST2600 supports multiple pin
groups for a function, the signal name on its own is no-longer unique,
and we must switch to the (signal, group) tuple. However, this means
that we can no-longer derive the signal expression symbol name from the
signal name alone, which among other cases, impacts the operation of the
PIN_DECL_x() macros.
To fix that and avoid requiring we awkwardly provide the associated
group name for every signal for every PIN_DECL_x() invocation, instead
opportunistically alias the name of the signal expression symbol from
the unique (signal, group) tuple to the also unique (pin, signal) tuple,
then reference the alias symbol in the tables generated by PIN_DECL_x().
This way we do not require extra group parameters for PIN_DECL_x() as
the pin name was already provided as an argument, and instead simply
require that the pin name be provided to the expression declaration
macros in order to generate the alias symbol.
The patch implements the alias strategy and fixes up all the expression
definition macro calls in the AST2400 and AST2500 drivers to account for
pin groups. Given the implementation strategy has the property that
compilation either fails or loudly warns for bad pin descriptions, this
patch is theoretically tested by successfully compiling both affected
drivers. For a more practical test I've inspected the diff of the
content of the pinctrl debugfs entries before and after the patch under
qemu; all pins, functions and groups match.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190729055604.13239-5-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename macros as follows:
* s/SS_PIN_DECL()/PIN_DECL_1()/
* s/MS_PIN_DECL()/PIN_DECL_2()/
* s/MS_PIN_DECL_()/PIN_DECL_()/
This is in preparation for adding PIN_DECL_3(). We could clean this up
with e.g. CPPMAGIC_MAP() from ccan, but that might be a bridge too far
given how much of a macro jungle we already have.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190729055604.13239-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix sparse warning:
drivers/pinctrl/aspeed/pinmux-aspeed.c:8:12: warning:
symbol 'aspeed_pinmux_ips' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190711142457.37028-1-yuehaibing@huawei.com
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While sorting out some devicetree issues I found that the pinctrl driver
was failing to acquire its GFX regmap even though the phandle was
present in the devicetree:
[ 0.124190] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: No GFX phandle found, some mux configurations may fail
Without access to the GFX regmap we fail to configure the mux for the
VPO function:
[ 1.548866] pinctrl core: add 1 pinctrl maps
[ 1.549826] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: found group selector 164 for VPO
[ 1.550638] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 144 (V20) for 1e6e6000.display
[ 1.551346] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 145 (U19) for 1e6e6000.display
...
[ 1.562057] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 218 (T22) for 1e6e6000.display
[ 1.562541] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 219 (R20) for 1e6e6000.display
[ 1.563113] Muxing pin 144 for VPO
[ 1.563456] Want SCU8C[0x00000001]=0x1, got 0x0 from 0x00000000
[ 1.564624] aspeed_gfx 1e6e6000.display: Error applying setting, reverse things back
This turned out to be a simple problem of timing: The ASPEED pinctrl
driver is probed during arch_initcall(), while GFX is processed much
later. As such the GFX syscon is not yet registered during the pinctrl
probe() and we get an -EPROBE_DEFER when we try to look it up, however
we must not defer probing the pinctrl driver for the inability to mux
some GFX-related functions.
Switch to lazily grabbing the regmaps when they're first required by the
mux configuration. This generates a bit of noise in the patch as we have
to drop the `const` qualifier on arguments for several function
prototypes, but has the benefit of working.
I've smoke tested this for the ast2500-evb under qemu with a dummy
graphics device. We now succeed in our attempts to configure the SoC's
VPO pinmux function.
Fixes: 7d29ed88ac ("pinctrl: aspeed: Read and write bits in LPC and GFX controllers")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190724080155.12209-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Further cleanup from the SPDX fixup fallout for the recent ASPEED
series. aspeed_g4_defconfig, aspeed_g5_defconfig and multi_v5_defconfig
now compile. Smoke tested the g4 and g5 kernels under QEMU's
palmetto-bmc and romulus-bmc machines respectively.
Fixes: 35d8510ea3ad ("pinctrl: aspeed: Fix missed include")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190710032216.4088-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SPDX churn made my fixes drop an important include
from the Aspeed pinctrl header. Fix it up.
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ASPEED pinctrl driver implementations make heavy use of macros to
minimise tedium of implementation and maximise the chance that the
compiler will catch errors in defining signal and pin configurations.
While the goal of minimising errors is achieved, it is at the cost of
the complexity of the macros.
Document examples of the expanded form of pin declarations to
demonstrate the operation of the macros.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-9-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ASPEED have completely rearranged the System Control Unit register
layout with the AST2600. The existing code took advantage of the fact
that the AST2400 and AST2500 had layouts that were similar enough to
have little impact on the pinmux infrastructure (though there is a wart
with read-modify-write vs write-1-clear semantics of the hardware
strapping registers between the two).
Given that any similarity has been thrown out with the AST2600, separate
out the function applying an expression state to be driver-specific.
With it, extract out the pinmux macro jungle to its own header and
implementation so the pieces can be composed without dependency cycles.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-8-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Writes of 1 to SCU7C clear set bits in SCU70, the hardware strapping
register. The information was correct if you squinted while reading, but
hopefully switching the order of the registers as listed conveys it
better.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-7-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have handled the GFX register case for quite some time now.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-6-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for
supporting SGPIO in AST2500 SoC.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang does not support this option:
warning: unknown warning option '-Woverride-init'; did you mean
'-Woverride-module'? [-Wunknown-warning-option]
1 warning generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WARN_ON() already contains an unlikely(), so it's not necessary to
wrap it into another.
Signed-off-by: Igor Stoppa <igor.stoppa@huawei.com>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes these warnings:
pinctrl-aspeed.c:112: warning: Function parameter or member 'map' not
described in 'aspeed_sig_desc_eval'
pinctrl-aspeed.c:112: warning: Excess function parameter 'regmap'
description in 'aspeed_sig_desc_eval'
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Yong Li found that writes to the AST2500 strapping register were not
properly supported by the Aspeed pinctrl core and provided a patch to
rectify the problem. Several revisions of the patch were posted and
ultimately v4 should have been applied, however some unfortunate
liberal application of tags on my part lead to confusion between v3[1]
and v4[2].
Generate the diff between v3 and v4 to apply as a fixup patch.
[1] http://patchwork.ozlabs.org/patch/801662/
[2] http://patchwork.ozlabs.org/patch/802946/
Cc: Yong Li <sdliyong@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On AST2500, the hardware strap register(SCU70) only accepts write ‘1’,
to clear it to ‘0’, must set bits(write ‘1’) to SCU7C
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the AST2500 USB functions as described by the devicetree
bindings. The AST2500 exposes five USB controllers through two USB
ports. Similar to the AST2400, the pins exposing USB are outliers with
respect to the rest of the pinmux as they not capable of GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the AST2400 USB functions as described by the devicetree
bindings. Three ports are fully documented in the datasheet and exposed
through the bindings and pinctrl, though there are remnants of
documentation for a fourth port muxed with GPIO pins GPIOQ6 and GPIOQ7.
The implementation is updated to reflect this but the function and
group are not exposed.
Disregarding the mostly undocumented fourth port, the USB functions are
an outlier with respect to the rest of the muxed functionality on the
AST2400 as GPIO is not supported on these pins.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g5 was performed on an AST2500EVB system,
using the strategy outlined in the commit message for the change to the
Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, using the strategy outlined in the commit message for the
change to the Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Several pinconf parameters have a fairly straight-forward mapping onto
the Aspeed pin controller. These include management of pull-down bias,
drive-strength, and some debounce configuration.
Pin biasing largely is managed on a per-GPIO-bank basis, aside from the
ADC and RMII/RGMII pins. As the bias configuration for each pin in a
bank maps onto a single per-bank bit, configuration tables will be
introduced to describe the ranges of pins and the supported pinconf
parameter. The use of tables also helps with the sparse support of
pinconf properties, and the fact that not all GPIO banks support
biasing or drive-strength configuration.
Further, as the pin controller uses a consistent approach for bias and
drive strength configuration at the register level, a second table is
defined for looking up the the bit-state required to enable or query the
provided configuration.
Testing for pinctrl-aspeed-g4 was performed on an OpenPOWER Palmetto
system, and pinctrl-aspeed-g5 on an AST2500EVB as well as under QEMU.
The test method was to set the appropriate bits via devmem and verify
the result through the controller's pinconf-pins debugfs file. This
simultaneously validates the get() path and half of the set() path. The
remainder of the set() path was validated by configuring a handful of
pins via the devicetree with the supported pinconf properties and
verifying the appropriate registers were touched.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Three video input signals suffered from a search/replace failure in
some copied code.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Port D and port E GPIO loopback modes are commonly enabled via hardware
straps for use with front-panel buttons. When the BMC is powered
off or fails to boot, the front-panel buttons are directly connected to
the host chipset via the loopback to allow direct power-on and reset
control. Once the BMC has booted, the loopback mode must be disabled for
the BMC to take over control of host power-on and reset.
Disabling these loopback modes requires writing to the hardware strap
register which violates the current design of assuming the system
designer chose the strap settings for a specific reason and they should
be treated as read-only. Only the two bits of the strap register related
to these loopback modes are allowed to be written and comments have been
added to explain why.
Signed-off-by: Rick Altherr <raltherr@google.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Incorrect video output configuration bits were being tested on pins in
GPIO banks AA and AB for the ROM{8,16} mux functions. The ROM{8,16}
functions are the highest priority for the relevant pins and also the
default function, so we require the relevant video output configuration
be disabled to mux GPIO functionality. As the wrong bits were being
tested a GPIO export would succeed but leave the pin in an unresponsive
state (i.e. value updates were ignored).
This misbehaviour was discovered as part of extending the GPIO
controller's support to cover banks Y, Z, AA, AB and AC (AC in the case
of the g5 SoC).
Fixes: 6d329f14a7 ("pinctrl: aspeed-g4: Add mux configuration for all pins")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g4 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms. Now, update the bindings document
to reflect the complete functionality and implement the necessary pin
configuration tables in the driver.
Cc: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prevented C20 from successfully being muxed as GPIO.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes simple typos in the initial commit. There is no behavioural
change.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Xo Wang <xow@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consider a scenario with one pin P that has two signals A and B, where A
is defined to be higher priority than B: That is, if the mux IP is in a
state that would consider both A and B to be active on P, then A will be
the active signal.
To instead configure B as the active signal we must configure the mux so
that A is inactive. The mux state for signals can be described by
logical operations on one or more bits from one or more registers (a
"signal expression"), which in some cases leads to aliased mux states for
a particular signal. Further, signals described by multi-bit bitfields
often do not only need to record the states that would make them active
(the "enable" expressions), but also the states that makes them inactive
(the "disable" expressions). All of this combined leads to four possible
states for a signal:
1. A signal is active with respect to an "enable" expression
2. A signal is not active with respect to an "enable" expression
3. A signal is inactive with respect to a "disable" expression
4. A signal is not inactive with respect to a "disable" expression
In the case of P, if we are looking to activate B without explicitly
having configured A it's enough to consider A inactive if all of A's
"enable" signal expressions evaluate to "not active". If any evaluate to
"active" then the corresponding "disable" states must be applied so it
becomes inactive.
For example, on the AST2400 the pins composing GPIO bank H provide
signals ROMD8 through ROMD15 (high priority) and those for UART6 (low
priority). The mux states for ROMD8 through ROMD15 are aliased, i.e.
there are two mux states that result in the respective signals being
configured:
A. SCU90[6]=1
B. Strap[4,1:0]=100
Further, the second mux state is a 3-bit bitfield that explicitly
defines the enabled state but the disabled state is implicit, i.e. if
Strap[4,1:0] is not exactly "100" then ROMD8 through ROMD15 are not
considered active. This requires the mux function evaluation logic to
use approach 2. above, however the existing code was using approach 3.
The problem was brought to light on the Palmetto machines where the
strap register value is 0x120ce416, and prevented GPIO requests in bank
H from succeeding despite the hardware being in a position to allow
them.
Fixes: 318398c09a8d ("pinctrl: Add core pinctrl support for Aspeed SoCs")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The newly added aspeed driver tries to check for a negative return
value from a pinctrl function, but stores the intermediate value in
a 'bool' variable, which cannot work:
drivers/pinctrl/aspeed/pinctrl-aspeed.c: In function 'aspeed_sig_expr_set':
drivers/pinctrl/aspeed/pinctrl-aspeed.c:192:11: error: comparison of constant '0' with boolean expression is always false [-Werror=bool-compare]
This slightly reworks the logic to use an explicit comparison with zero
before assigning to the temporary variable.
Reported-by: Colin King <colin.king@canonical.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
