This describes all of the SCIF hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When initialising SCI devices their names will be .serial
not .sci.
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This will be used when initialising SCI devices using DT
until common clock framework support is added.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Lager board, i2c and iic cores can be interchanged since they can be
muxed to the same wires. Commit e489c2a9bc
("ARM: shmobile: lager: enable i2c devices") activated the i2c cores,
yet the iic cores should be default since they have the more interesting
features for generic use cases, i.e. SMBUS_QUICK and DMA (yet to be
supported).
Reported-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
I2C bus for VDD MPU regulator is IIC3, not I2C3.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk is not supported when devices are initialised
using DT, so remove it from the command line.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[horms+renesas@verge.net.au: minor witespace changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SPI device for RSPI on Genmai.
On this board, only rspi4 is in use. Its bus contains a single device
(a wm8978 audio codec), for which no bindings are defined yet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable internal AHB-PCI bridges for the USB EHCI/OHCI controllers attached to
them.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
[Sergei: enabled PCI0]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the R8A7790 internal PCI bridge devices.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
[Sergei: added several properties to the PCI bridge nodes]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch support PIO transfer only at this point
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a default PCIe bus clock node.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[horms+renesas@verge.net.au: resolved conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device tree clock node for the PCIe Controller
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a default PCIe bus clock node.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds the device tree clock node for the PCIe Controller
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
audio_clk_a/b/c are required from sound driver
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch support PIO transfer only at this point
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the I2C2 device node.
Based on the Koelsch I2C2 device tree patch by Wolfram Sang.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
A second i2c6 node was a added by
05e234a187058ee ("ARM: shmobile: koelsch dts: Add VDD MPU regulator for
DVFS"). Merge this into the existing node.
Also shuffle i2c nodes so they are all together.
Cc: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Due to an error when merging df40f256b18300e1 ("ARM: shmobile:
lager: add i2c1, i2c2 pins") a duplicate i2c3 node.
This patch moves the duplicate and moves to old node to
be closer to the other new i2c nodes.
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the Lager DTS to make use of the new unified legacy
memory map where the legacy window on Lager and Koelsch
have the same size.
With this change in place the code gets aligned with the
documentation.
After update the Lager board has the following map:
Bank0: 1GiB RAM (Legacy 32-bit: 0x40000000->0x7fffffff)
Bank1: 3GiB RAM (LPAE area: 0x140000000->0x1ffffffff)
Before the update the old map looked like this:
Bank0: 2GiB RAM (Legacy 32-bit: 0x40000000->0xbfffffff)
Bank1: 2GiB RAM (LPAE area: 0x180000000->0x1ffffffff)
Tested with and without LPAE on r8a7790 Lager.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Due to an error when resolving conflicts df40f256b18300e1 ("ARM: shmobile:
lager: add i2c1, i2c2 pins") added the i2c[12]_pins nodes to the wrong
node.
This patch moves them to their correct location in the pfc node.
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add pinctrl definitions for i2c1 and i2c2 busses on the Lager board
to ensure these are setup correctly at initialisation time. The i2c0
and i2c3 busses are connected to single function pins.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[horms+renesas@verge.net.au: Added shmobile to patch title]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add i2c0, i2c1, i2c2 and i2c3 nodes to the Lager reference device tree as
these busses all have devices on them that can be probed even if they
are no drivers yet.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[horms+renesas@verge.net.au: Added shmobile to title]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP
table. Due to the lack of proper OPP definition, use an arbitrary safe
value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every
OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this
value since the clock transition latency is not the only parameter that
will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since DVS is not supported in R-CAR Gen2.
- clocks
phandle to the CPU clock source. This clock source is used for all the
2 CortexA15 located inside the same cluster.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CA15 cluster is capable of voltage scaling. Add the regulator
in the i2c6 node, to allow the generic CPUFreq driver to use it.
Enable the i2c6 pin mux and the device node as well since the
da9210 is connected to that bus.
Note: In R-CAR Gen2, each frequency is using the same voltage,
and DVS control is not used. Therefore, this patch set the
voltage(Vmin/Vmax) to 1000mv.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add needed information inside CPU0 for the generic cpufreq-cpu0 driver.
- voltage-tolerance = 1%
It reflects the tolerance for the CPU voltage defined inside the OPP
table. Due to the lack of proper OPP definition, use an arbitrary safe
value.
- clock-latency = 300 us
Approximate worst-case latency to do a full DVFS transition for every
OPPs. Due to the lack of HW information, use an arbitrary safe value.
Note: The term transition-latency will be more accurate to define this
value since the clock transition latency is not the only parameter that
will define the overall DVFS transition.
- operating-points = < kHz - uV >
List of 6 operating points. All of them are using the same voltage
since the valid Vmin voltage is not documented in the HW spec.
- clocks
phandle to the CPU clock source. This clock source is used for all the
4 CortexA15 located inside the same cluster.
Signed-off-by: Benoit Cousson <bcousson+renesas@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Change the setting of OPPs for ES2.0]
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The CA15 cluster is capable of voltage scaling. Add the regulator
in the i2c3 node, to allow the generic CPUFreq driver to use it.
Enable the i2c3 pin mux and the device node as well since the
da9210 is connected to that bus.
Note: In R-CAR Gen2, each frequency is using the same voltage,
and DVS control is not used. Therefore, this patch set the
voltage(Vmin/Vmax) to 1000mv.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
[gaku.inami.xw@bp.renesas.com: Changes Vmin for disabling DVS]
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add clocks for the SYS-DMAC0 and SYS-DMAC1 hardware blocks.
Cfr. the r8a7790 version by Ben Dooks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The of_find_compatible_node() function returns a new reference to the
found node. Instead of just adding of_node_put() calls, simplify the
code by moving the CPU identification logic inside the loop over cpu
nodes, in order to lower complexity from O(n) to O(1) by replacing
of_find_compatible_node() calls with of_device_is_compatible().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As early printk support is not enabled in the kernel in the
shmobile defconfig it does not make much sense to provide for
it in the default command line.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
