* 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
agp: Remove the BKL from agp_open
inifiband: Remove BKL from ipath_open()
mips: Remove BKL from tb0219
drivers: Remove BKL from scx200_gpio
drivers: Remove BKL from pc8736x_gpio
parisc: Remove BKL from eisa_eeprom
rtc: Remove BKL from efirtc
input: Remove BKL from hp_sdc_rtc
hw_random: Remove BKL from core
macintosh: Remove BKL from ans-lcd
nvram: Drop the bkl from non-generic nvram_llseek()
nvram: Drop the bkl from nvram_llseek()
mem_class: Drop the bkl from memory_open()
spi: Remove BKL from spidev_open
drivers: Remove BKL from cs5535_gpio
drivers: Remove BKL from misc_open
When iser enabled lu reset support it did not set the
bit to allow userspace to get/set the timeout. This
sets the tgt and lu reset timeout bits.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Include link scope as part of address resolution. Combine local
and remote address resolution into a single, simpler code path.
Fix error checking in the IPv6 routing lookups.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ Fix up cma_check_linklocal() for !IPV6 case. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Merge resolve local/remote address resolution into a single
data flow to ensure consistent access and use of the local routing
tables.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The RDMA CM is intended to support the use of a loopback address
when establishing a connection; however, the behavior of the CM
when loopback addresses are used is confusing and does not always
work, depending on whether loopback was specified by the server,
the client, or both.
The defined behavior of rdma_bind_addr is to associate an RDMA
device with an rdma_cm_id, as long as the user specified a non-
zero address. (ie they weren't just trying to reserve a port)
Currently, if the loopback address is passed to rdam_bind_addr,
no device is associated with the rdma_cm_id. Fix this.
If a loopback address is specified by the client as the destination
address for a connection, it will fail to establish a connection.
This is true even if the server is listing across all addresses or
on the loopback address itself. The issue is that the server tries
to translate the IP address carried in the REQ message to a local
net_device address, which fails. The translation is not needed in
this case, since the REQ carries the actual HW address that should
be used.
Finally, cleanup loopback support to be more transport neutral.
Replace separate calls to get/set the sgid and dgid from the
device address to a single call that behaves correctly depending
on the format of the device address. And support both IPv4 and
IPv6 address formats.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ Fixed RDS build by s/ib_addr_get/rdma_addr_get/ - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_dev_addr stores net_device address information:
the source device address, destination hardware address, and
broadcast address. For consistency, store the net_device type
rather than converting it to the rdma_node_type.
The type indicates the format of the various hardware addresses,
which is what we're concerned with, and not the RDMA node type
that the address may map to.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a source address is provided, verify that the address family matches
that of the destination address. If the source is not specified, use the
same address family as the destination.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide the device interface when resolving route information to
ensure that the correct outbound device is used. This will also
simplify processing of sin6_scope_id for IPv6 support.
Based on work from:
David Wilder <dwilder@us.ibm.com>
Jason Gunthorpe <jgunthrope@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If joining to an AF_INET6 address, we need to map the address to a MGID
in the same way as the IP stack. The old code would just fall through to
the IPv4 case and generate garbage.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
RDMA CM treats AF_INET6 addresses that are either 0 or prefixed with
FF1x:A01B::/32 as MGIDs, but the detection for the prefix was buggy;
fix it up.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
for_each_netdev() should be used with RTNL or dev_base_lock held,
or else we risk a crash.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export rdma_set_ib_paths to user space to allow applications to
manually set the IB path used for connections. This allows
alternative ways for a user space application or library to obtain
path record information, including retrieving path information
from cached data, avoiding direct interaction with the IB SA.
The IB SA is a single, centralized entity that can limit scaling
on large clusters running MPI applications.
Future changes to the rdma cm can expand on this framework to
support the full range of features allowed by the IB CM, such as
separate forward and reverse paths and APM.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Reviewed-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
After dma-mapping an SG list provided by the SCSI midlayer, iser has
to make sure the mapped SG is "aligned for RDMA" in the sense that its
possible to produce one mapping in the HCA IOMMU which represents the
whole SG. Next, the mapped SG is formatted for registration with the HCA.
This patch re-writes the logic that does the above, to make it clearer
and simpler. It also fixes a bug in the being aligned for RDMA checks,
where a "start" check wasn't done but rather only "end" check.
Signed-off-by: Alexander Nezhinsky <alexandern@voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary. This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size. The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length. Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is no such flag DE - the field is reserved and should be zero.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch was generated by
git grep -E -i -l '[Aa]quire' | xargs -r perl -p -i -e 's/([Aa])quire/$1cquire/'
and the cumsumed was found by checking the diff for aquire.
Signed-off-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
cycle_kernel_lock() got pushed down to ipath_open(). I tried hard to
understand what it might protect, but finally gave up.
Roland noted that qlogic seems to have abandoned the ipath driver and
came to the following wise conclusion: "So I guess if the BKL stuff is
blocking you in any way, we can just drop it from ipath and leave it
as yet another race condition in a rotting old driver."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <adad44tj090.fsf@cisco.com>
Cc: Roland Dreier <rdreier@cisco.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (34 commits)
[SCSI] qla2xxx: Fix NULL ptr deref bug in fail path during queue create
[SCSI] st: fix possible memory use after free after MTSETBLK ioctl
[SCSI] be2iscsi: Moving to pci_pools v3
[SCSI] libiscsi: iscsi_session_setup to allow for private space
[SCSI] be2iscsi: add 10Gbps iSCSI - BladeEngine 2 driver
[SCSI] zfcp: Fix hang when offlining device with offline chpid
[SCSI] zfcp: Fix lockdep warning when offlining device with offline chpid
[SCSI] zfcp: Fix oops during shutdown of offline device
[SCSI] zfcp: Fix initial device and cfdc for delayed adapter allocation
[SCSI] zfcp: correctly initialize unchained requests
[SCSI] mpt2sas: Bump version 02.100.03.00
[SCSI] mpt2sas: Support dev remove when phy status is MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT
[SCSI] mpt2sas: Timeout occurred within the HANDSHAKE logic while waiting on firmware to ACK.
[SCSI] mpt2sas: Call init_completion on a per request basis.
[SCSI] mpt2sas: Target Reset will be issued from Interrupt context.
[SCSI] mpt2sas: Added SCSIIO, Internal and high priority memory pools to support multiple TM
[SCSI] mpt2sas: Copyright change to 2009.
[SCSI] mpt2sas: Added mpi2_history.txt for MPI2 headers.
[SCSI] mpt2sas: Update driver to MPI2 REV K headers.
[SCSI] bfa: Brocade BFA FC SCSI driver
...
This patch allows a local IPv6 address to be resolved by rdma_cm.
To reproduce the problem:
$ rping -s -v -a ::0 &
$ rping -c -v -a <IPv6 address local to this system>
rdma_resolve_addr error -1
Local IPv6 address was obtained with "ip addr show ib0"
Addresses: https://bugs.openfabrics.org/show_bug.cgi?id=1759
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
in_dev_get() can return NULL. If it does, iwch_query_port() will crash.
Handle the NULL case by mapping it to port state INIT.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In commit cb58160e ("RDMA/iwcm: Reject the connection when the cm_id
is destroyed") a call to the provider's reject handler was added to
destroy_cm_id() to fix a provider endpoint leak. This call needs to
be done with interrupts enabled. So unlock and relock around this
call. This is safe because:
1) the provider will do nothing with this endpoint until the iwcm either
accepts or rejects.
2) the lock is only released after the iwcm state is changed, so an
errant iwcm app that is destroying -and- rejecting the connection
concurrently will get a failure on one of the calls.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use this_cpu_ptr and __this_cpu_ptr in locations where straight
transformations are possible because per_cpu_ptr is used with
either smp_processor_id() or raw_smp_processor_id().
cc: David Howells <dhowells@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
cc: Ingo Molnar <mingo@elte.hu>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Don't turn on carrier for a non-active port
IB/mthca: Fix access to freed memory in catastrophic event handling
mlx4_core: Pass cache line size to device FW
RDMA/nes: Remove duplicate .ndo_set_mac_address field initialization
IB/mad: Fix lock-lock-timer deadlock in RMPP code
Multicast joins can succeed even if the IB port is down. This happens
when the SM runs on the same port with the requesting port. However,
IPoIB calls netif_carrier_on() when the join of the broadcast group
succeeds, without caring about the state of the IB port. The result
is an IPoIB interface in RUNNING state but without an active IB port
to support it.
If a bonding interface uses this IPoIB interface as a slave it might
not detect that this slave is almost useless and failover
functionality will be damaged. The fix checks the state of the IB
port in the carrier_task before calling netif_carrier_on().
Adresses: https://bugs.openfabrics.org/show_bug.cgi?id=1726
Signed-off-by: Moni Shoua <monis@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
catas_reset() uses a pointer to mthca_dev, but mthca_dev is not valid
after the call to __mthca_restart_one().
Based on a similar patch for mlx4 (634354d7, "mlx4: Fix access to
freed memory") by Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The definition of nes_netdev_ops has initializations of a local function
and eth_mac_addr for its ndo_set_mac_address field. This change uses only
the local function.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I, s, fld;
position p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@s@
identifier I, s, r.fld;
position r.p0,p;
expression E;
@@
struct I s =@p0 { ... .fld@p = E, ...};
@script:python@
p0 << r.p0;
fld << r.fld;
ps << s.p;
pr << r.p;
@@
if int(ps[0].line)!=int(pr[0].line) or int(ps[0].column)!=int(pr[0].column):
cocci.print_main(fld,p0)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Holding agent->lock across cancel_delayed_work() (which does
del_timer_sync()) in ib_cancel_rmpp_recvs() leads to lockdep reports of
possible lock-timer deadlocks if a consumer ever does something that
connects agent->lock to a lock taken in IRQ context (cf
http://marc.info/?l=linux-rdma&m=125243699026045).
Fix this by changing the list items to a new state "CANCELING" while
holding the lock, and then canceling the delayed work without holding
the lock. If the delayed work runs after the lock is dropped, it will
see the state is CANCELING and return immediately, so the list will
stay stable while we traverse it with the lock not held.
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Originally, walk_memory_resource() was introduced to traverse all memory
of "System RAM" for detecting memory hotplug/unplug range. For doing so,
flags of IORESOUCE_MEM|IORESOURCE_BUSY was used and this was enough for
memory hotplug.
But for using other purpose, /proc/kcore, this may includes some firmware
area marked as IORESOURCE_BUSY | IORESOUCE_MEM. This patch makes the
check strict to find out busy "System RAM".
Note: PPC64 keeps their own walk_memory_resouce(), which walk through
ppc64's lmb informaton. Because old kclist_add() is called per lmb, this
patch makes no difference in behavior, finally.
And this patch removes CONFIG_MEMORY_HOTPLUG check from this function.
Because pfn_valid() just show "there is memmap or not* and cannot be used
for "there is physical memory or not", this function is useful in generic
to scan physical memory range.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let attribute group vectors be declared "const". We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...
Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to <asm-generic/socket.h> in the x86 tree. The generic
header has the same new #define's, so that works out fine.
- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.
Noted in 'next' by Stephen Rothwell.
If the cm_id of a connect request is destroyed prior to the ULP
accepting or rejecting the connection, then the provider never cleans
up the connection. The iwcm should explicitly reject these
connections if the cm_id is destroyed.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
FW mismatches can cause a crash in the iw_cxgb3 event handler.
- NULL the t3cdev->ulp pointer on failures in cxio_rdev_open()
- Silently ignore events when the ulp ptr is NULL in iwch_err_handler()
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
MADs are UD and can be dropped if there are no receives posted, so
allow receive queue size to be set with a module parameter in case the
queue needs to be lengthened. Send side tuning is done for symmetry
with receive.
Signed-off-by: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep reported a possible deadlock with cm_id_priv->lock,
mad_agent_priv->lock and mad_agent_priv->timed_work.timer; this
happens because the mad module does
cancel_delayed_work(&mad_agent_priv->timed_work);
while holding mad_agent_priv->lock. cancel_delayed_work() internally
does del_timer_sync(&mad_agent_priv->timed_work.timer).
This can turn into a deadlock because mad_agent_priv->lock is taken
inside cm_id_priv->lock, so we can get the following set of contexts
that deadlock each other:
A: holding cm_id_priv->lock, waiting for mad_agent_priv->lock
B: holding mad_agent_priv->lock, waiting for del_timer_sync()
C: interrupt during mad_agent_priv->timed_work.timer that takes
cm_id_priv->lock
Fix this by using the new __cancel_delayed_work() interface (which
internally does del_timer() instead of del_timer_sync()) in all the
places where we are holding a lock.
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Old query_port code reports static MTU and link state values.
Instead, map actual MTU to next largest IB_MTU_* constant and
correctly report link state.
Cc: Steve Wise <swise@opengridcomputing.com>
Reported-by: Jeff Squyres <jsquyres@cisco.com>
Signed-off-by: Chien Tung <chien.tin.tung@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The disconn routine has been reworked to acoomodate the terminate and
flushing changes. The routine has been reorganized to make all the
decisions at the start then it performs all the required operations.
This simplified the lock handling and is easier to follow.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the flush status to fill in cqe status when a specific error has
been identified. Subsequent flushed completions still use the flushed
value.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a flush request is given to the hw, it will place one cqe marked
as flushed (unless there is nothing to flush). An application that is
waiting for all wqe's to complete will be left hanging. This modifies
poll_cq to return the correct number of flushes for the pending
elements on the wq.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an asynchronous event occurs that requires a terminate, it is
sometimes possible to identify the wqe in error. This change uses
flush to get this information to the poll routine. The flush
operation puts the status into the cqe. If this information is not
available, it continues to use the more generic flush code as before.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement the sending and receiving of Terminate packets.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
CQ errors are not being handled correctly. Put in the the upcall for
CQ errors.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a QP is destroyed, unprocessed CQ entries could still reference
the QP. This change zeroes the context value at QP destroy time. By
skipping over cqe's with a zero context, poll_cq no longer processes a
cqe for a destroyed QP.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The routine to allocate a cqp request is not called from process
context code. Since it is not OK to sleep, it needs to use GFP_ATOMIC
not GFP_KERNEL.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code currently has a work structure in the QP. This requires a
lock and a pending flag to ensure there is never more than one request
active. When two events happen quickly (such as FIN and LLP CLOSE),
it causes unnecessary timeouts since the second one is dropped.
This fix allocates memory for the work request so the second one can
be queued. A lock is removed since it is no longer needed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During termination, it is possible for the refcnt to go to zero while
the worker thread is posting events upward. This fix increments the
refcnt before the request is passed to the worker thread. The thread
decrements the refcnt when the request is completed.
Signed-off-by: Don Wood <donald.e.wood@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When the mthca driver uses the same name for interrupts for every
device in the system. This can make it very confusing trying to work
out exactly which device MSI-X interrupts are for. Change the driver
to add the PCI name of the device to the interrupt name.
Signed-off-by: Arputham Benjamin <abenjamin@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_ib_lock_cqs()/mthca_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_config_reg.h was including <asm/page.h> for no reason -- the whole
file is just defines of constants, so it's entirely self-contained.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib_lock_cqs()/mlx4_ib_unlock_cqs() are helper functions that
lock/unlock both CQs attached to a QP in the proper order to avoid
AB-BA deadlocks. Annotate this so sparse can understand what's going
on (and warn us if we misuse these functions).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev->ibdev.iwcm allocation may fail, prevent a dereference.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since the original commit 883a99c7 ("[IB] uverbs: Add a mask of device
methods allowed for userspace"), the uverbs core returns EINVAL for
commands not implemented by a specific low-level driver.
This creates a problem that there is no way to tell the difference
between an unimplemented command and an implemented one which is
incorrectly invoked (which also returns EINVAL).
The fix is to have unimplemented commands return ENOSYS.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Until now, retries were only sent when joining a multicast group. This
patch will adds retries when leaving a multicast group as well.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Yossi Etigin <yosefe@voltaire.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open-coded reimplementations with printk_once().
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use the %pM conversion specifier to print a MAC address.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than just defining static spinlock_t variables and then
initializing them later in init functions, simply define them with
DEFINE_SPINLOCK() and remove the calls to spin_lock_init(). This cleans
up the source a tad and also shrinks the compiled code; eg on x86-64:
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-40 (-40)
function old new delta
ib_uverbs_init 336 326 -10
ib_mad_init_module 147 137 -10
ib_sa_init 123 103 -20
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The hop count field in a directed route MAD is only allowed to be in the
range 0 to 63 (by spec). Check that this really is the case to avoid
accessing outside the bounds of the hop array.
Reported-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Check that the format of multicast link addresses is correct before
taking them from dev->mc_list to priv->multicast_list. This way we
never try to send a bogus address to the SA, which prevents badness
from erronous 'ip maddr addr add', broken bonding drivers, etc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IPoIB currently must use irqsave locking for priv->lock, since it is
taken from interrupt context in one path. However, ipoib_send() does
skb_orphan(), and the network stack locking is not IRQ-safe.
Therefore we need to make sure we don't hold priv->lock when calling
ipoib_send() to avoid lockdep warnings (the code was almost certainly
safe in practice, since the only code path that takes priv->lock from
interrupt context would never call into the network stack).
Addresses: http://bugzilla.kernel.org/show_bug.cgi?id=13757
Reported-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
strlcpy() will always null terminate the string. node_desc is not
guaranteed to be NUL-terminated so just use memcpy().
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver was reporting CQE flags in the wrong bit positions, causing
consumers to miss incoming immediate data.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The old code used a lot of hard-coded values, which might not be valid
in all environments (especially routed fabrics or partitioned
subnets). Copy as much information as possible from the incoming
request to correct that.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make port autodetect mode the default for the ehca driver. The
autodetect code has been in the kernel for several releases now and
has proved to be stable.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A close/abort while waiting for a wr_ack during connection migration
can cause a hung process in iwch_accept_cr/iwch_reject_cr.
The fix is to set rpl_error/rpl_done and wake up the waiters when we
get a close/abort while in MPA_REQ_RCVD state.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Keep ref on connection request endpoints until either accepted or
rejected so it doesn't get freed early.
- Endpoint flags now need to be set via atomic bitops because they can
be set on both the iw_cxgb3 workqueue thread and user disconnect
threads.
- Don't move out of CLOSING too early due to multiple calls to
iwch_ep_disconnect.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Massage the err_handler upcall into an event handler upcall, pass
netdev port events to the cxgb3 ULPs and generate RDMA port events
based on LLD port events.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __init and __exit annotations to the module_init/module_exit
functions from drivers/infiniband/core/addr.c and cma.c.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Increment version number for DMEM toleration.
Signed-off-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dma_sync_single() is deprecated now, and the use in mthca is wrong:
there should be a dma_sync_single_for_cpu() before touching the memory
from the CPU, and a dma_sync_single_for_device() afterwards. Fix
this, prompted by a kick in the pants from a patch from FUJITA
Tomonori <fujita.tomonori@lab.ntt.co.jp>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During cluster testing, one QP was not closed, as FIN is not handled
properly when its rexmit count expires or in some cases when RST is is
received after sending FIN. The reason is that the cm_id does not get
decremented under these conditions.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In nes_query_device(), max_qp_init_rd_atom is incorrectly set to
max_qp_wr. This was found when a test application had a dapl async
event error.
Signed-off-by: Faisal Latif <faisal.latif@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This prevents the memcpy() of a guid_entries element using a negative index.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement toleration of dynamic memory operations and 16 GB gigantic
pages, where "toleration" means that the driver can cope with dynamic
memory operations that happen before the driver is loaded. While the
ehca driver is loaded, dynamic memory operations are still prohibited
by returning NOTIFY_BAD from the memory notifier.
On module load the driver walks through available system memory,
checks for available memory ranges and then registers the kernel
internal memory region accordingly. The translation of address ranges
is implemented via a 3-level busmap.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: general@lists.openfabrics.org
Cc: Christoph Raisch <raisch@de.ibm.com>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Cc: general@lists.openfabrics.org
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mlx4: Add strong ordering to local inval and fast reg work requests
IB/ehca: Remove superfluous bitmasks from QP control block
RDMA/cxgb3: Limit fast register size based on T3 limitations
RDMA/cxgb3: Report correct port state and MTU
mlx4_core: Add module parameter for number of MTTs per segment
IB/mthca: Add module parameter for number of MTTs per segment
RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
infiniband: Remove void casts
IB/ehca: Increment version number
IB/ehca: Remove unnecessary memory operations for userspace queue pairs
IB/ehca: Fall back to vmalloc() for big allocations
IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
