It adds a new sysfs file, where the user can configure the mcbsp mode to use.
If the mcbsp channel is in use, it does not allow the change.
Than in omap_pcm_open we can call the omap_mcbsp_get_opmode to get the mode,
store it, than use it to implement the different modes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch renames the symbols that handles threshold
sysfs properties. This way we can add more sysfs properties
to them.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch export through sysfs two properties to configure
maximum threshold for transmission and reception on each
mcbsp instance. Also, it exports two helper functions to
allow mcbsp users to read this values.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a way to handle transmit/receive threshold.
It export to mcbsp users a callback registration procedure.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Increasing startup delay value as worst case:
CLKSRG*2 = 8000khz: (1/8000) * 2 * 2 usec
Although, 100us may give enough time for two CLKSRG,
due to some unknown PM related, clock gating etc. reason,
this patch increases it to 500us.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC has an annoying bug letting either L or R channel to be
played on L channel. In other words, L and R channels can
switch at random. This provides McBSP funtionality that may
be used to fix this feature.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Simultaneous audio playback and capture on OMAP1510 can cause that second
stream is stalled if there is enough delay between startup of the audio
streams.
Current implementation of the omap_mcbsp_start is starting both transmitter
and receiver at the same time and it is called only for firstly started
audio stream from the OMAP McBSP based ASoC DAI driver.
Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is
missed if there is no DMA transfer set up at that time when the first word
after McBSP startup is transmitted. The problem hasn't noted before since
later OMAPs are using level sensitive DMA request lines.
Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by
allowing to start and stop individually McBSP transmitter and receiver
logics. Then call those functions individually for both audio playback
and capture streams. This ensures that DMA transfer is setup before
transmitter or receiver is started.
Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem
analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA
request line behavior differences between the OMAP generations.
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If XSYNCERR or RSYNCERR interrupts are enabled, they are never
cleared causing the IRQ handler to be continuously called.
This patch clears the IRQs in question in the event they are
enabled and taken.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables writing to McBSP Transmit Configuration Control
Register (XCCR) and Receive Configuration Control Register (RCCR)
for 2430/34xx platforms. It also adds XCCR, RCCR entries in McBSP
register configuration structure and bit definitions for both
registers.
If we enable the writing to CCR registers for 2430/34xx and don't
set the default values (setting 0 as a consequence) in ASoC driver,
the Transmit/Receive DMA mode gets disabled and the the
transmission/reception doesn't happen, ending with a
"write error: Input/Output error" when playing with 'aplay'.
Also define dummy CCR registers for omap1.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bootloader may let McBSP logic running so make sure that block is idle
before requesting IRQs. Also make sure that TX and RX waitqueues are
initialized before request_irq.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on Chandra's earlier patches in linux-omap tree.
Note that omap1_mcbsp_check and omap2_mcbsp_check are no longer
needed as there's now omap_mcbsp_check_valid_id() defined.
Also some functions can now be marked __init.
Signed-off-by: Chandra Shekhar <x0044955@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use __init but __devinit to define probe function. A pointer to
omap_mcbsp_probe is passed to the core via platform_driver_register and
so the function must not disappear when the init code is freed. Using
__init and having HOTPLUG=y the following probably oopses:
echo -n omap-mcbsp.1 > /sys/bus/platform/driver/omap-mcbsp/unbind
echo -n omap-mcbsp.1 > /sys/bus/platform/driver/omap-mcbsp/bind
While at it move the remove function to the .devexit.text section.
Signed-off-by: Uwe Kleine-König <ukleinek@strlen.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mcbsp is confused as to what takes a physical or virtual address.
Fix the two instances where it gets it wrong.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch transform mcbsp code to use platform data
from arch/arm/plat-omap/devices.c
It also gets ride of ifdefs on mcbsp.c code.
To do it, a platform data structure was defined.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fix lots of warnings and errors reported by
scripts/checkpatch.pl on arch/arm/plat-omap/mcbsp.c.
Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP1 some McBSP features depend on DSP. Also export
polling functions as suggested by Luis Cargnini.
Signed-off-by: Tony Lindgren <tony@atomide.com>
mach-integrator/pci_v3.c: no need to reference 'irq' arg, its constant
mach-omap1/pm.c: remove extra whitespace
arch/arm/mach-sa1100/ssp.c: remove braces around single C stmt
arch/arm/plat-omap/mcbsp.c:
- remove pointless casts from void*
- make longer lines more readable
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds minimal OMAP2430 support to plat-omap files to
get the kernel booting on 2430SDP.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Untested, but this should fix up the bulk of the totally mechanical
issues, and should make the actual detail fixing easier.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
McBSP does not need sys_ck or sys_clkout. If the devices connected
to McBSP need sys_clkout, they need to request it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Tony Lindgren
Update misc OMAP core code from linux-omap tree:
- McBSP updates by Samuel Ortiz, Andrzej Zaborowski
- Whitespace cleanups by Ladislav Michl
- Other fixes by various linux-omap developers
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes OMAP clock framework to use clk_enable/disable
instead of clk_use/unuse as specified in include/linux/clk.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Serial port and framebuffer init improvments by Imre Deak
- Common omap pin mux framework by Tony Lindgren
- Common omap clock framework by Tony Lindren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Clock updates by Tuukka Tikkanen, Juha Yrjola,
Daniel Petrini and Tony Lindgren
- DMA fixes by Imre Deak, Juha Yrjola and Daniel Petrini
- Add support to dual-mode hardware timers by Lauri Leukkunen
- GPIO support for 24xx by Paul Mundt
- GPIO wake-up support by Tony Lindgren
- Better GPIO interrupt handler to not lose interrupts by
Ralph Walden and Ladislav Michl
- Power Management updates by Tuukka Tikkanen
- Make Power Management code use new SRAM functions by
Tony Lindgren
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch by various OMAP developers syncs the OMAP
specific arch files with the linux-omap tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Tony Lindgren
This patch move common OMAP code from arch-omap to plat-omap
directory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
